Fiber Optic Media Converters

Transcription

1 Video iber Optic edia Converters iber Optic edia Converters Utilizes Small orm-factor Plggable (SP) modles lti-mode and single-mode modles available Spports distances p to 20 km (12.4 miles) Srface mont or rack mont capability The Bosch fiber optic edia Converter series are designed to transmit 10/100 bps signals over fiber optic cable sing Small orm-factor Plggable (SP) modles. These fiber optic media converter devices can be sed to transmit data well beyond the 100 m limit of copper-based media and provides a secre, EI/RI free transmission path. The media converter nits are designed to accept 10/100 bps SP modles. The SP modles are ordered separately to meet ser reqirements for mode type, distance and type of optical connector. Available offerings inclde mlti-mode fiber () or single-mode fiber (S) models with a single SC connector or dal-fiber with an LC connector. System overview VG4-SPSCKT The VG4-SPSCKT is a niqe media converter modle for se with VG4 series AtoDomes incorporating the (TCP/IP) Commnications odle, as well as with IC Series 550, 550IR, and 612 cameras. This media converter modle is designed to accept any of the 10/100 bps SP modles described below. The media converter modle along with the SP modle is ser installed directly into the power spply box of the AtoDome camera or of the IC camera to provide an integrated fiber optic soltion. Refer to the Installation Gide that accompanies the VG4-SPSCKT for detailed installation instrctions. CNE2C/IN The CNE2C/IN is a media converter device designed to transmit and receive 10/100 bps data over optical fiber sing SP modles. This head-end device is spplied in an enclosre that can be srface monted or rack monted sing the optional C1-IN rack mont card cage. The nit does not reqire infield adjstments, and provides atomatic DI/DI-X crossover. SP odles The selection of Small orm-factor Plggable (SP) modles provides the fast optical interface when sing the VG4-SPSCKT or the CNE2C/IN media converters. These interchangeable SP modles are available for se with or S optical fiber. The optical fiber SP modles are available as one and two fiber versions. They also are available with LC or SC optical connectors.

2 2 iber Optic edia Converters The VG4-SPSCKT and CNE2C/IN media converters accept the following SP modles: odle iber Type Optical Interface Dplex LC S Dplex LC 5 Single SC SP26 Single SC The 5/6 modles are conterparts; if yo se one in the VG4-SPSCKT modle, then yo mst se the other in the CNE2C/IN head-end nit. Refer to the chart below for the acceptable combinations. Compatibility Chart If this SP modle is sed with the VG4-SPSCKT 5 6 Then this SP modle mst be sed in the CNE2C/IN 6 5 C1-IN Rack ont Card Cage The C1-IN rack mont card cage is designed to hold a maximm of 14 CNE2C/IN modles. The C1-IN card cage tilizes an integral, yet field replaceable niversal power spply sitable for 120 VAC to 240 VAC, 50/60 Hz operation. The C1-IN nit incldes atomatic self-resetting crrent overload protection, so a falt in any one modle will not case the entire card cage to sht down. C1-BP Closre Panel The C1-BP is a closre panel for the C1-IN rack mont card cage, providing coverage for one rack slot. Installation/configration notes The Bosch iber Optic edia Converter soltion consists of three core components and several optional components to help fit every application. To provide fiber optic commnications between a Bosch VG4 AtoDome and a controller, yo mst se the following: One (1) VG4-SPSCKT iber Optic edia Converter Kit a printed circit board installed inside a VG4 power spply box. (See Technical Specification Section 1) One (1) CNE2C/IN iber Optic edia Converter a rack-monted or srface monted headend controller. (See Technical Specification Section 2) Two (2) Small orm-factor Plggable (SP) modles one modle is installed in the VG4-SPSCKT, the other is installed in the CNE2C/IN. (See Technical Specification Section 3) Optionally, yo can se the following modles to cstomize yor installation: C1-IN Rack ont Card Cage (See Technical Specification Section 4) C1-BP Closre Panel To provide fiber optic commnications between a IC Series 550, 550IR, or 612 camera and a controller, yo mst se the following: One (1) VG4-SPSCKT iber Optic edia Converter Kit a printed circit board installed inside a IC IP power spply box. (See Technical Specification Section 1) One (1) Small orm-factor Plggable (SP) modle one modle is installed in the VG4-SPSCKT. (See Technical Specification Section 3) Technical specifications Section 1: VG4-SPSCKT iber Optic edia Converter Kit Compatible Receiver Installation /Link (on circit board) iber Optic edia Converter kit. Reqires a small form-factor plggable (SP) modle (sold separately). 10/100 bps ll Dplex or Half Dplex Port ll Dplex Optical Port CNE2C/IN Installed inside a VG4-A-PA1, VG4-A-PA2, VG4 A PSU1 or a VG4 A PSU2 power spply box, or in a IC IP PSU, with spplied monting hardware. Note: Wiring for the VG4-SPSCKT mst be roted throgh the proper condit opening on the power spply box. Refer to the installation gide that accompanies the modle. is applied, fiber link is valid Red is applied, fiber link is missing / Red, rapid / Red, slow RJ-45 Connector is applied iber link is valid and video is streaming from the camera to a network connection is applied iber link is valid Video is not streaming from the camera, or the RJ45 connection to the camera is not valid

3 3 iber Optic edia Converters Amber No data is present Link is valid at 100 B If the right side is flashing green, link is valid at 10 B No LED lit issing the network cable, defective network cable or the other end of the network cable is not connected Crrent Protection Circit Board echanical Shipping Weight TB ma (spplied by the camera) Atomatic resettable Solid-state crrent limiters eets IPC Standard 7.4 x 7.1 x 3.8 cm (2.9 x 2.8 x 1.5 in.) 0.91 kg (2 lb) > 100,000 hors Section 2: CNE2C/IN iber Optic edia Converter Installation iber Optic edia Converter kit. Reqires a small form-factor plggable (SP) modle (sold separately). 10/100 bps ll Dplex or Half Dplex Port ll Dplex Optical Port Srface mont or rack mont sing C1-IN rack (sold separately) No LED lit Indicates a loss of fiber connection : power is spplied None: no power spplied is spplied No LED lit No power spplied RJ-45 Connector Amber No data is present Link is valid at 100 B If the right side is flashing green, link is valid at 10 B Spplied Pack Inpt: VAC, 50/60 Hz Otpt: 9 1 A odle: ma Crrent Protection Circit Board echanical Shipping Weight TB Operating Temperatre Storage Temperatre Relative Hmidity Atomatic resettable Solid-state crrent limiters eets IPC Standard 16.0 x 13.0 x 2.8 cm (6.3 x 5.1 x 1.1 in.) 0.91 kg (2 lb) > 100,000 hors 40 C to +75 C ( 40 to +167 ) 40 C to +85 C ( 40 to +185 ) 0% to 95% (non-condensing) Connectors Terminal block RJ-45 (10/100 BASE-T/TX) Reglatory Compliance cul, UL, RoHS Section 3: SP odles Socket Link/Act SP (10/100 BASE-X) Indicates a good fiber connection Indicates data is present on at least one side of the IP connection echanical Interchangeable modles available for se with or S optical fiber. 10/100 bps

4 4 iber Optic edia Converters, 5, 6 Weight (all SP modles) 55.5 x 13.5 x 8.5 mm (2.2 x 0.5 x 0.3 in.) 63.8 x 13.5 x 8.5 mm (2.5 x 0.5 x 0.3 in.) 0.23 kg (.05 lb) Otpt Voltage sing Indicator AC Line Cord 9 VDC ± 5% at 6.5 A at 75 C (167 ) 1.25 A slow blow (rack power spply) (plg-in modles individally electronically fsed) Red LED Detachable, IEC-connected. US, Eropean, and UK power cords spplied. echanical Ty pe Conn ector Dpl ex LC Wavelength (transmit/ receive) ax. Distance Rack Slots Shipping Weight 48 x 19 x 15 cm (19.0 x 7.5 x 6.0 in.) orteen (14) 1-in. slots available 3.4 kg (7.5 lb) S Dpl ex LC 20 km (12.4 miles) TB >100,000 hors 5 6 iber Compatibility Optical iber Compatibility, Optical iber Compatibility, S Optical Distance Specifications Singl e SC Singl e SC 1550 nm 1550 nm / 60/125 µm. or 50/125 µm fiber, sbtract 4 db from the specified optical bdget vale. st meet or exceed fiber standard ITU-T G /125 µm S. st meet or exceed fiber standard ITU-T G.652. Specified transmission distances are limited to the optical loss of the fiber and any additional loss introdced by connectors, splices, and patch panels. The modles are designed to operate over the entire optical loss bdget range, so they do not reqire a minimm loss in order to operate. Section 4: C1-IN Rack ont Card Cage Rack mont card cage designed to hold a maximm of 14 CNE2C/IN modles Red is spplied No LED lit No power Operating Temperatre Storage Temperatre Heat Generation Reglatory Compliance 40 C to +75 C ( 40 to +167 ), ambient 40 C to +85 C, ( 40 to +185 ), ambient 240 BTU Ordering information CC part 15,, cul, UL, RoHS VG4 SPSCKT iber Optic edia Converter Kit media converter video transmitter/data receiver fiber optic kit Order nmber VG4-SPSCKT CNE2C/IN Rack-monted iber Optic edia Converter Single-port 10/100 bps edia Converter, 120/230 VAC Order nmber CNE2C/IN SP 2 Small orm factor Plggable Optical Interface SP iber Optic odle, lti-mode,, 2 km (1.2 miles), 2 LC connectors Order nmber SP 3 Small orm factor Plggable Optical Interface SP iber Optic odle, Single-mode,, 20 km (12.4 miles), 2 LC connectors Order nmber SP 25 Small orm factor Plggable Optical Interface SP iber Optic odle, lti-mode, 1310/1550 nm,, 1 SC connector Order nmber 5 Inpt Voltage VAC at 1 A maximm

5 5 iber Optic edia Converters SP 26 Small orm factor Plggable Optical Interface SP iber Optic odle, lti-mode, 1550/,, 1 SC connector Order nmber 6 Accessories C1-IN Rack ont Card Cage for CNE2C EIA 19-in. rack for CNE2C, VAC Order nmber C1-IN C1 BP Blank Panel for C1 Rack Blank panel for C1 rack mont card cage, 1 slot width (1 in.) Order nmber C1-BP