DI-80. When Accuracy Counts
|
|
- Carmella Paul
- 5 years ago
- Views:
Transcription
1 DI-80 Indi cator When Accracy Conts Operation Manal 73357
2 CONTENTS 1. INTRODUCTION Display A/D Section Item Memory Environment Interface Option CONFIGURATION Dimensions External Connectors Control Panel Keyboard Keys Display Icons & Indicator Lamps BASIC OPERATION Tare Sbtraction Semi-Ato Tare Sbtraction (One Toch Tare) Digital Tare Sbtraction (Preset Tare) Gross Weight Display Weight Unit Conversion Dal Scale Fnction Accmlation Weight Hold Fnction Animal Weighing Fnction Setpoint Fnction Setpoint Vale Entry Call Item Code in Weighing Mode COUNTING OPERATION Unit Weight Entry Unit weight entry by sampling Direct Entry by nmeric keys Accmlation of Conting Reslt Call Item Code in Conting Mode PROGRAM MODE Item Memory Alphanmeric Data Entry Item Programming Memory Edition and Deletion Delete and edit a certain Item Code Erase all Item data in memory Review Item Code already in Memory Date and Time...36 APPENDIX APPENDIX I LIST OF ASCII DATA..38 APPENDIX II LIST OF TERAOKA CODE.39 2
3 1. INTRODUCTION The DI-80 series is a general prpose weighing indicator for se in a variety of weighing, check weighing, conting systems. It can operate p to two analoge scales. The DI-80 featres, in its basic configration, two scales interface, 1,000 item memory, back light LCD display with color bars, battery operation, flly isolated setpoint interface, one serial interface. For more complex application, expansion modles; bilt-in thermal printer, analoge otpt interface (will be available near ftre), and RS-232C/485 interface are available Display 7 Digits LCD display Color Weight Checker Bars 17 digits dot matrix display (5 x 8 dots) for alphanmeric display CCFL Back Light Indicators: Zero, Net/Gross, Stable, Tare, Battery Weight Base Indicator: kg, oz, g, dwt, lb and (Pcs) 1.2. A/D Section A/D Conversion Speed: 30 times per sec. (at 1mV/V) Internal Resoltion: 1/500,000 or 1,000,000 Display Resoltion: 2500d - 10,000 Excitation Voltage: 12VDC Scale Channel: Nmber of Load Cells: Remote Sensing fnction Inpt Sensitivity: 0.4mV/V to 4.0mV/V Scale Interface: Amphenol 14 pin 2 scale channels Total 8 x 350 ohm load cells in parallel configration (total load cells of scale 1 and 2) 1.3. Item Memory 1,000 item memory as standard (Expandable p to 2,000 item memory as factory option). Memory fields of item code are as follows; Parameter Max Length Programmable Character Item Code 12 or 16 Alphanmeric or Nmeric Part Nmber 12 or 16 Alphanmeric or Nmeric Part Name 20 Alphanmeric Tare Weight 5 Nmeric Unit Weight 5 Nmeric Inventory 8 Nmeric Setpoint 1 6 Nmeric Setpoint 2 6 Nmeric Setpoint 3 6 Nmeric Setpoint 4 6 Nmeric 3
4 1.4. Environment Power Spply : 9VDC to 15VDC Inpt 1.5A or 6 pcs of D size battery (Via solder bridges, Di-80 can be configred for dry cell battery drive or rechargeable battery drive.) Operating Temperatre : -10 C to 40 C Operating Hmidity : 15% to 85% RH 1.5. Interface SETPOINT INTERFACE : RS-232C INTERFACE : Max 35VDC 500mA The device to be connected can be selected by internal specification. BAR-CODE SCANNER (PSC QUICKscan 6000 series) BAR-CODE PRINTER (ELTRON LP2622 series) PC 1.6. Option OP1 BUILT IN THERMAL PRINTER The bilt-in printer modle Thermal serial dot printer (SEIKO MTP201) Paper Size : 50mm diameter (58mm width) OP2 RS-232/RS-485 Interface board Optional interface board has RS-232C interface and 2 x RS-485 interface. It can be plgged into the interface socket of the CPU board. OP3 Analoge Otpt Interface board (will be available near ftre) Optional analoge otpt board provides an analoge otpt signal with 11 bit resoltion (Max 2000d). Via jmper switch, it can be configred for crrent otpt (4-20mA) or voltage otpt (0-10V). It can be plgged into the interface socket of the CPU board. 4
5 2. CONFIGURATION 2.1. Dimensions Display Key Panel Battery Cover Bilt-in Printer (Option) 2.2. External Connectors DC Power Inpt 1) RS-232C Interface 2) Setpoint Inteface 3) RS-485 Interface (Optional RS-232C/485 Board) 3) RS-232C Interface (Optional RS-232C/485 Board) 4) Scale 1 Interface 5) Scale 2 Interface DC Power Inpt b a): 9.5± 0.5mm b): Inside (-) 2.1± 0.5mm Otside (+) 5.5± 0.5mm 1 RS-232C Interface DIN 8 Pin (Female) 2 Setpoint Otpt Interface Mini DIN 8 pin (Female) 3 RS-232/485 Interface RS-232C DIN 8 Pin (Female) RS-485 RJ45(8 Pin) 4 Scale 1 interface Amphenol 14 pin 5 Scale 2 Interface Amphenol 14 pin - + a 5
6 2.3. Control Panel Keyboard Keys ON/STAND BY KEY: Switches between the ON and Stand-by mode. MODE KEY: Switches check weighing and conting mode. (Enter program mode with RE-ZERO key.) / B/G INVENT /GROSS KEY: Switches Between Net weight and Gross weight mode. If Item data is called, display inventory data. (By internal specification setting.) Program Inventory data in Program Mode. HOLD HOLD KEY: Enable/ disable Hold Fnction Pcs SAMPLE KEY: Calclate and enter a nit weight of item by sampling in conting mode and program mode. WEIGHT UNIT KEY: Select weight nits. Pcs UNIT WEIGHT KEY: Enter a nit weight of Item(per 1000 pcs) in conting mode and program mode. SCALE KEY: Switch between platform 1 and 2 when connecting two platforms. - Contined to the next page 6
7 FEED KEY: Feed paper when sing an optional bilt in printer. SET POINT KEY: Enter Setpoint Data. T TARE KEY: Enter or clear tare vale. 0 ZERO KEY: Set the scale to zero. - DATE + PROG # IN/OUT C SUBTRACT KEY: Sbtract weight vale (a qantity of parts in conting mode) to total memory. Set the date and time in program mode. Set parts name to item data in program mode. ADD KEY: Add weight vale (a qantity of parts in conting mode) to total memory. Set set point data to item data in program mode. TOTAL KEY: Clear total memory. Print the label or receipt when printer is sed. Save the data in program mode. CODE KEY: Call p item code. Select shipping, receiving, or stocktaking mode. Set parts no data to item data in program mode. CLEAR KEY: Clear keyed-in data. DECIMAL KEY: Enter the decimal comma dring nmeric entry. 0-9 NUMERIC KEY: Enter nmeric data. 7
8 Display Icons & Indicator Lamps Checker Display Main Display nd Display INSUFF IN HOLD MEMORY SCALE 1 RECOMP OUT PROG SCALE Indicators Descriptions of Indicators 1 0 Zero Lamp Weight is stable at zero point. 2 T Tare Lamp Presence of Tare weight 3 B/G Gross Lamp Gross weight is displayed. 4 Battery Lamp Battery needs to be recharged. 5 ~ Stable Lamp Weight is stable. 6 Net Lamp Net weight is displayed. 7 Pcs Pieces Lamp 1 Qantity is displayed. 8 kg,g,oz,lb, Weight Base Main display shows weight in the indicated weight base. dwt Lamps 9 Total Lamp Total weight is displayed on the left half of sb-display. 10 Unit Weight Lamp 1 Unit weight is displayed on the left half of sb-display. 11 Unit Weight Lamp 2 Unit weight is displayed on the right half of sb-display. 12 Pieces Lamp 2 Qantity is displayed on the right half of sb-display. Triangle Indicator Lamps INSUFF Insfficient Lamp Sample weight is too small to calclate nit weight. RECOMP Recompting Lamp Unit weight may be re-compted for higher accracy. IN IN (Receiving) Lamp Add a qantity of parts to item inventory. OUT OUT (Shipping) Lamp Remove a qantity of parts from item inventory. HOLD Hold Lamp Hold Fnction is enable. MEMORY Memory Lamp Accmlation data is in memory. PROG Program Lamp Scale is in Program mode. SCALE 1 Scale1 Lamp Scale 1 is in se. SCALE 2 Scale2 Lamp Scale 2 is in se. 8
9 3. BASIC OPERATION 3.1. Tare Sbtraction Semi-Ato Tare Sbtraction (One Toch Tare) This fnction is sed for sbtracting tare vale of an empty container. 1. Check that the indicator is at 0 ~ gross zero. 2. Pt the container on ~ platform. 0,526 kg 3. Sbtract the tare. [ T ] ~ T 4. Fill container to reqired ~ weight. T Note * 2) 1,376 kg Note: 1) To clear the tare vale, press [0] then [ T ] key or remove all the weight from the platform and press [ T ] key. Note: * 2) When the optional printer is sed, the net weight will be printed by [ ] key. 31 JAN :19PM * 1,376kg 9
10 Digital Tare Sbtraction (Preset Tare) This fnction can be sed when tare weight vale is known. It is sed for sbtracting tare vale of a prefilled container. 1. Check that the indicator is at 0 ~ gross zero. 2. Enter the tare vale thogh [ 5 ], [, ] 0 ~ nmeric keys. [ 1 ], [ 5 ] i.e. 5,158kg [ 8 ] 5, Sbtract the tare. [ T ] ~ T - 5,158 kg 4. Pt filled container. ~ T 11,376 kg Note: 1) To clear the tare vale, press [0] then [ T ] key or remove all the weight from the platform and press [ T ] key. 10
11 3.2. Gross Weight Display DI-80 series can switch the display between the net weight and gross weight. 1. Enter tare vale by any mean ~ of 3.1 Tare Sbtraction. T i.e. Tare vale = kg - 5,158 kg 2. Pt weight on the platter. ~ i.e. Gross weight = kg T 14,006 kg 3. Display Gross weight. B/G ~ [/ B/G] T 19,164 kg 4. Change to Net weight ~ display. [/ B/G] T 14,006 kg Note: This fnction can be invalid by internal specification setting. (SPEC25 BIT0) 11
12 3.3. Weight Unit Conversion This fnction allows to convert the weight data in display to other weight base(s) by key operation. The convertible weight nits are different from the base nit that the scale was calibrated with. The convertible nits to each base nit and the conversion seqence when the designated key operation is done, are listed in the following table. The base nit kg lb g oz dwt The convertible nits and the seqence kg lb kg lb kg lb g oz dwt g oz dwt g oz dwt g oz dwt 1. Pt weight on the platter. ~ (i.e. Kg as base nit) 1,746 kg 2. Change to lb base. [WEIGHT ~ UNIT] 3,850 lb 3. Back to kg base. [WEIGHT ~ UNIT] 1,746 kg Note: This fnction can be invalid by internal specification setting. (SPEC12 BIT0) 12
13 3.4. Dal Scale Fnction This fnction is available only when the system has two platforms/scales. DI-80 switch the scale to be sed by pressing [SCALE] key. The active platform is indicated by indicator lamps (scale 1 and scale 2) on the display. 1. Scale 1 is sed. ~ 2. Change to scale 2. [SCALE] 0 ~ 0,00 kg 3. Back to scale 1. [SCALE] ~ 1,746 kg 13
14 3.5. Accmlation The weight data can be accmlated or sbtracted by sing [ + ] and [ - ] keys. Total net weight will be held and displayed in the indicator. When accmlation data is in memory, the nit weight conversion nor the scale change fnctions are invalid. The total data will be cleared by pressing [ ] key. 1. Pt weight on the platform. ~ 2,162 kg 2. Add the weight to total [ + ] ~ memory. total W E I G H T 2, Clear the total display by [ C ] 0 ~ pressing [ C ] key. And, remove the weight 4. Pt next weight on the platter ~ 5. Add the weight to total [ + ] ~ memory. 1,204 kg total W E I G H T 3, Contine - 14
15 6. Clear the total display by [ C ] 0 ~ pressing [ C ] key. And, remove the weight 7. Pt weight on the platter ~ Note: *1) 8. Void/ Sbtract the weight [ - ] ~ from total memory 1,204 kg total W E I G H T 2, Clear the total data. [ ] 0 ~ (Scale is back to weighing display atomatically.) Note *3) Note: *1) To view crrent total, press [ ] key. Note: 2) Total display after [ + ], [ - ] key can be cleared atomatically by specification. Note: *3) When the optional printer is sed, the transaction will be printed by [ ] key. 31 JAN :19PM + 2,162kg + 1,204kg - 1,204kg 3T 2,162kg 15
16 3.6. Weight Hold Fnction DI-80 can hold weight display for 15 seconds. By internal specification setting, the weight data can be hold at the first stabilized point or peak point. This fnction is effective when pressing [HOLD] key. This fnction is effective when the indicator lamp (HOLD) is on by pressing [HOLD] key. Weight hold at the first stable point Weight hold at peak point Display Weight Display Weight Actal Weight Actal Weight 3.7. Animal Weighing Fnction DI-80 can alter 4 different display filter levels by internal specification setting. (SPEC34 and 35) Also, DI-80 series spports the animal weighing fnction to average the in-consist weight and display the averaged weight for mch vibration and other environmental inflences. This fnction is effective by internal specification settings.(spec36) 16
17 3.8. Setpoint Fnction Up to 4 setpoint vales can be programmed by specification. The setpoint signals are otpt via the setpoint interface when the qantity or weight exceeds setpoint vales. The character of the parameter can be selected from the following selections by internal specification setting. (SPEC # 07 Bit 1 & 2) Setpoint 1 Weight Weight Qantity Qantity Setpoint 2, (&3), (&4) Weight Percentage of setpoint 1 vale Qantity Percentage of setpoint 1 vale Setpoint 1 and Setpoint 2 can be tilized as nder and over limits of filling or check weighing application. The indicator shows the nder/over stats adiovisally with color graphic display and internal bzzer. This fnction is valid when both of setpoint 1 and setpoint 2 are entered and setpoint 2 is larger than setpoint 1. The setpoint alarm for filling or check weighing application can be selected by internal specification setting. (SPEC # 17 Bit 2) SETPOINT ALARM FOR FILLING APPLICATION Intermittent bzzer will beep when the weight or qantity is between Setpoint 1 and Setpoint 2. Continos bzzer will beep when the weight exceeds setpoint 2. E.g.) SETPOINT 1 (Weight Base) = 2.500kg SETPOINT 2 (Percentage of SETPOINT 1) = 120 % No Sond Intermittent Bzzer Continos Bzzer kg 120%(3.000kg) Setpoint 1 Setpoint 2 SETPOINT ALARM FOR CHECK WEIGHING APPLICATION The bzzer will beep when the weight or qantity is ot of target limits for check weighing application by internal specification setting. Intermittent Bzzer No Sond Intermittent Bzzer kg 120%(3.000kg) Setpoint 1 Setpoint 2 COLOR GRAPHIC DISPLAY Color graphic display consists of total 15 graphic blocks. Each block shows the achievement rate to the target range. Fnctions Yellow Block shows the achievement rate to the minimm limit (setpoint 1) Green Block shows the weight stats in the target range. Red Block shows the exceed rate against the maximm weight (setpoint 2) 17
18 Setpoint Vale Entry 1. stand-by stats 0 ~ 2. Go to Setpoint Setting mode. [SET 0 ~ POINT]key SP 1 3. Enter Setpoint 1 vale and [ 2 ], [ ], 0 ~ enter the data by pressing [ 0 ], [ 0 ], [SETPOINT] key. [ 0 ], [SET i.e kg POINT]key 4. Enter Setpoint 2 vale and [ 2 ], [ ], 0 ~ enter the data by pressing [ 5 ], [ 0 ], [SETPOINT] key. [ 0 ], [SET i.e kg POINT]key SP 2 Note: 1) If the entry of setpoint 3 and 4 are reqired, repeat the same procedre for Setpoint 3 and 4. Note: 2) If Setpoint 3 and 4 are not reqired, press [SET POINT] key withot entering data. 5. Fill the prodct to the ~ container. i. e. 2,200kg 2,200 kg 6. When the weight data 0 ~ reaches to the lower set point, remove the weight. 18
19 3.9. Call Item Code in Weighing Mode This section shows how to recall item codes in weighing mode. (Item code shold be pre-programmed in program mode before the following operation.) Refer to 5. PROGERAM MODE) 1. Stand-by stats 0 ~ 2. Enter the item code. [ 1 ], [ 0 ], 0 ~ [ 0 ], [ # ] C O N E J 8 W Note: If parts name is programmed to item code, the parts name is displayed in the second display. 3. Place item on platter. ~ weight. 1,376 kg Note: * 2) C O N E J 8 W Note: 1) If setpoint data is programmed to item code, the checker display shows the weight stats. Note: * 2) When the optional printer is sed, the net weight will be printed by [ ] key. 31 JAN :19PM 100 * 1,376kg CONEJ8 19
20 4. COUNTING OPERATION DI-80 has the conting mode. To switch between weighing mode and conting mode, press [MODE] key Unit Weight Entry The nit weight can be determined by sampling or direct entry thogh nmeric keys Unit weight entry by sampling 1. Go to conting mode. [MODE] 0 ~ 0 0 Pcs Pcs 2. Place 10 samples onto the ~ platter and check INSUFF lamp is off. 0,186 kg 1 0 Pcs Pcs Note: If the sample qantity is not 10 pcs, enter the nmber of samples by nmeric key. 3. Compte a nit weight. [ Pcs ] ~ 0,186 kg Pcs Pcs Note: 1) DI-80 calclate the average nit weight by [Pcs]. To calclate the accrate nit weight, a sfficient nmber of items are reqired. Note: 2) Unit weight of item is displayed on the left half of the 2 nd display. Note: 3) Qantity is displayed on the right half of the 2 nd display. Note: 4) The indicator watches whether the weight of samples are enogh to calclate a nit weight. If sample pieces are not sfficient for accrate conting, the Insfficient lamp is lit. If calclate the nit weight with insfficient samples, the procedre 4 and 5 are reqired. The insfficient range can be selected in internal setting mode from 0.1% or 0.2% of fll scale capacity. - Contined - 20
21 4. Add the reqired samples. ~ Add kg 0 P C S Pcs Pcs Note: The additional sample qantity for accrate calclation is displayed on the left half of the 2 nd display. 5. Calclate nit weight with [ Pcs ] ~ sfficient samples. 0,149 kg Pcs Pcs 6. Cont item qantity. ~ 4,184 kg Note *4) Pcs Pcs Note *5) Note: 1) To clear nit weight data, press [ C ] key. Note: 2) If mltiple scales are connected to DI-80, it is qenerally recommended to perform the sampling operation with smaller capacity for better accracy. Note: 3) To retrn to weighing mode, press [MODE] key. Note: *4) Accracy of nit weight can be improved with more qantity than the sample qantities becase a larger sample size makes the weight variance smaller. Unit weight can be improved by [ Pcs ] key when RECOM lamp is ON. Note: *5) When the optional print is sed, the conting reslt will be printed by [ ] key. 31 JAN :19PM * 224Pcs 21
22 Direct Entry by nmeric keys 1. Go to conting mode. [MODE] 0 ~ 0 0 Pcs Pcs 2. Enter nit weight vale. [ 1 ], [ 8 ], 0 ~ [ ], [ 6 ], [ 9 ], [ 3 ] Note: The nit weight shold be 1000 pcs of items Pcs Pcs 3. Enter nit weight. [ Unit 0 ~ Weight ] Pcs Pcs 4. Place parts on the platter. ~ 2,757 kg Pcs Pcs 22
23 4.2. Accmlation of Conting Reslt In conting mode, DI-80 will accmlate the conting reslts in total memory. 1. Go to conting mode and 0 ~ enter nit weight by any means of 4.1 Unit Weight Entry Pcs Pcs 2. Place parts onto the platter. ~ 3,756 kg Pcs Pcs 3. Add the qantity to total [ + ] ~ memory. total Pcs Q U A N T I T Y Pcs Pcs 4. Clear the total display by [ C ] 0 ~ pressing [ C ] key. And, remove the weight Pcs Pcs 5. Pt parts on the platter. ~ 0,221 kg Pcs Pcs 6. Sbtract the qantity from [ - ] ~ total memory. total Pcs Q U A N T I T Y Pcs Pcs - Contine - 23
24 7. Enter the nmber of parts [ 1 ], [ 0 ], 0 ~ by nmeric key. [ 0 ], [ 0 ] (When adding or sbtracting the known qantity) Pcs Pcs 8. Add the qantity 0 ~ total pcs Q U A N T I T Y Pcs Pcs 9. Clear the total data. [ ] 0 ~ (Retrn to conting mode atomatically.) kg Pcs Pcs Note: *1) To view crrent total, press [ ] key. Note: 2) Total display after [ + ], [ - ] key can be cleared atomatically by specification. Note: *3) When the optional printer is sed, the transaction will be printed by [ ] key. 31 JAN :19PM Pcs - 146Pcs Pcs 3T 3335Pcs 24
25 4.3. Call Item Code in Conting Mode This section shows how to recall item codes in conting mode. (Item code shold be pre-programmed in program mode before the following operation.) Refer to 5. PROGERAM MODE) 1. Go to Conting Mode. 0 ~ Pcs Pcs Note: If parts name is programmed to item code, the parts name is displayed for a second in the second display. 2. Enter the item code. [ 1 ], [ 0 ], 0 ~ [ 0 ], [ # ] Pcs Pcs Note: If the nit weight is programmed to item code, the nit weight is recalled atomatically and displayed for a second display. 3. Select parts movement [ # ] 0 ~ stats Pcs Pcs Note: If Inventory qantity is programmed to item code, the inventory data is p-dated atomatically by pressing [ ] key. If yo do not se the inventory fnction, please skip this procedre. When In lamp is lit, a qantity of item is added to item inventory. When Ot lamp is lit, a qantity of item is removed from item inventory. When neither are lit, item inventory is not changed. In-Ot stats can be selected by pressing [ # ] key after calling p item code. The stats is toggled between IN, OUT, NON ADD (NO CHANGE). - Contine - 25
26 4. Place parts item on platter. ~ weight. 1,816 kg Note: 2) Pcs Pcs Note: 1) If setpoint data is programmed to item code, the checker display shows the weight stats. Note: *2) When the optional printer is sed, the transaction will be printed by [ ] key. 31 JAN :19PM 100 SCREW103 * 1449Pcs 26
27 5. PROGRAM MODE 5.1. Item Memory DI-80 series has 1000 item memory (can be expanded to 2000 item memory as factory option). Item code consists of the following data. Parameter Character Data Length Item Code Nmeric or 12 or 16 letters Note: *1) Alphanmeric Parts No. Nmeric or 12 or 16 letters Note: *1) Alphanmeric Parts Name Alphanmeric 20 letters Tare Weight Nmeric 5 digits Unit Weight Nmeric 5 digits Setpoint Nmeric 8 digits Inventory qantity Nmeric 8 digits Note: * 1) The maximm length and the programmable character can be set by specification. ITEM CODE Item code is sed as a reference code to call p item data. PARTS NO Parts No will be printed on label and transmitted to PC when connecting bar-code printer and PC. If barcode printer nor PC is not sed, yo may skip to program parts No. PARTS NAME Parts No will be printed on label and transmitted to PC when connecting bar-code printer and PC. When calling item code in operation mode, the parts name will be displayed in the 2 nd display. TARE WEIGHT Maximm length of data depends on the scale capacity and interval of yor system. If several tare container will be sed to one item code, yo may skip to store tare data to item memory. UNIT WEIGHT Unit weight can be registered by sampling or nmeric data entry in program mode. If an item is sed in weighing mode only, yo may skip to store nit weight data to item memory. INVENTORY QUANTITY Inventory qantity will be p-dated atomatically after IN/OUT operation in conting mode. If an item is sed in weighing mode only, yo may skip to store inventory data to item memory. SETPOINTS Maximm 4 setpoints can be programmed to each item code. The character of setpoint data can be selected from weight base or qantity base. 27
28 Alphanmeric Data Entry Alphanmeric data can be programmed to Item no., parts no, parts name. Yo may select the data entry by ASCII code or TERAOKA entry (two digit nmeric data) by internal spec selection. ASCII CODE ENTRY by ASCII code P 16 SCREW:CROMATE23_ A00 PARAMETER NAME: P: Parts Name n: Parts No I : Item Code ASCII DISPLAY: Shows that entry is by ASCII. POSITION OF CURSOR: These two digits shows the position of crsor. [ + ] and [ - ], to move crsor position. The example shows the crsor is at 16 th digit in part name. ASCII DATA: Entered ASCII code data is displayed. CONVERTED ALPHANUMERIC DATA: The alphanmeric data is displayed. FUNCTION KEYS IN ASCII CODE ENTRY [ C ] = Escape from Alphanmeric screen [ + ] = Move the crsor ahead [ - ] = Move the crsor back [WEIGHT UNIT CHANGE] = A [Pieces] = B [SCALE CHANGE] = C [UNIT WEIGHT] = D [SETPOINT] = E [FEED] = F [ 0 ] = 0 [ 1 ] = 1 [ 2 ] = 2 [ 3 ] = 3 [ 4 ] = 4 [ 5 ] = 5 [ 6 ] = 6 [ 7 ] = 7 [ 8 ] = 8 [ 9 ] = 9 i.e.) To enter SCREW: enter [ 5 ], [ 3 ] [ 4 ], [ 3 ] [ 5 ], [ 2 ] [ 4 ], [ 5 ] [ 5 ], [ 7 ] [ 3 ], [ A ] S C R E W : Note ) Refer to Appendix I (ASCII CODE LIST) 28
29 TERAOKA CODE ENTRY Data can be entered by TERAOKA character code. P 16 t00 SCREW:CROMATE23_ PARAMETER NAME: P: Parts Name n: Parts No I : Item Code TERAOKA DISPLAY: Shows that entry is by TERAOKA CODE. POSITION OF CURSOR: These two digits shows the position of crsor. [ + ] and [ - ], to move crsor position. The example shows the crsor is at 16 th digit in part name. TERAOKA DATA: Entered TERAOKA code data is displayed. CONVERTED ALPHANUMERIC DATA: The alphanmeric data is displayed. FUNCTION KEYS IN ASCII CODE ENTRY [ C ] = Escape from Alphanmeric screen [ + ] = Move the crsor ahead [ - ] = Move the crsor back [ 0 ] = 0 [ 1 ] = 1 [ 2 ] = 2 [ 3 ] = 3 i.e.) To enter SCREW:, enter [ 1 ], [ 9 ] [ 0 ], [ 3 ] [ 1 ], [ 8 ] [ 0 ], [ 5 ] [ 2 ], [ 3 ] [ 4 ] = 4 [ 5 ] = 5 [ 6 ] = 6 [ 7 ] = 7 [ 8 ] = 8 [ 9 ] = 9 S C R E W Note: Refer to Appendix II (TERAOKA CODE LIST) 29
30 Item Programming 1. Go to program mode. [MODE] + [RE- ZERO] ProG P L U C O U N T 0 Note) Press [MODE] key while pressing [RE-ZERO] key. Note) The 2 nd display shows the nmber of items that exist in memory. 2. Enter Item Code nmber and [ 1 ], [ 0 ], 0 ~ press [ # ] key. [ 0 ], [ # ] 3. Enter tare vale by any means 0 ~ of 3.1 Tare Sbtraction. T 8 Pcs Pcs - 0,500 kg 8 Pcs Pcs 4. Enter nit weight vale by any 0 ~ means of 4.1 Unit weight T entry. 0,056 kg 1 8, Pcs Pcs 5. Press [GROSS] key to enter [GROSS] inventory vale. InvEnt 0 30
31 6. Enter inventory qantity and [ 1 ], [ 5 ], 0 ~ press [GROSS] key. [ 0 ], [ 0 ], T [GROSS] 0,056 kg 1 8, i.e.1500pcs Pcs Pcs 7. Press [ - ] key to enter [ - ] parts no. n 00 A00 8. Enter data to parts No and [ 3 ], [ 5 ], 0 ~ press [ ] key. [ 4 ], [ 0 ], T [ 5 ], [ 4 ], 0,056 kg Refer to Alphanmeric [ 5 ], [ 2 ], 1 8, data entry. [ ] Pcs Pcs i.e. 5ATR 9. Press [ # ] key to enter [ # ] parts name. P 00 A Enter parts no and [ 5 ], [ 3 ], 0 ~ press [ # ] key. [ 4 ], [ 3 ], T [ 5 ], [ 2 ], 0,056 kg Refer to Alphanmeric [ 4 ], [ 5 ], 1 8, data entry. [ 5 ], [ 7 ], Pcs Pcs i.e. SCREW [ # ] 31
32 11. Press [ + ] key to enter [ + ] setpoint data. SP 1 pcs 12. Enter Setpoint 1 and press [ 3 ], [ 5 ], [ + ] key. [ 0 ], [ + ], SP 2 pcs i.e. 350 pcs 13. Enter Setpoint 2 and press [ 4 ], [ 0 ], [ + ] key. [ 0 ], [ + ], SP 3 pcs i.e. 400 pcs 14. Enter Setpoint 3 and press [ 5 ], [ 0 ], 0 ~ [ + ] key. [ 0 ], [ + ], T 0,056 kg 1 8, i.e. 500 pcs Pcs Pcs Note: The setpoint data can be selected from weight base or qantity base by internal specification settings. If the data is based on weight, please enter the weight vale in the procedre (Refer to 3.8 Setpoint Fnction) If the setpoint data is not reqired, skip the operation procedre Save the data to memory. [ ] ProG P L U C O U N T 1 32
33 5.2. Memory Edition and Deletion Delete and edit a certain Item Code 1. Go to program mode. [MODE] + [RE- ZERO] ProG P L U C O U N T 1 0 Note) Press [MODE] key while pressing [RE-ZERO] key. Note) The 2 nd display shows the nmber of items that exist in memory. 2. Enter Item Code to delete [ 1 ], [ 0 ], and press [ # ] key. [ 0 ], [ # ] ProG If calling the item that has C L E A R P L U? already existed in item memory, this display appears. To edit an item data. 3. Press [ # ] key. [ # ] 0 ~ T 0,056 kg The display is changed to item 1 8, programming screen. Pcs Pcs Note: * 1) Note: * 1) After changing item data, save the data by [ ] key. To clear a certain item code. 4. Clear the data by [ C ] key. [ C ] ProG P L U C O U N T 9 33
34 Erase all Item data in memory 1. Go to program mode. [MODE] + [RE- ZERO] ProG P L U C O U N T 1 0 Note) Press [MODE] key while pressing [RE-ZERO] key. Note) The 2 nd display shows the nmber of items that exist in memory. 2. Enter [ ], [ ], [ 0 ], while [ ], [ ], pressing [ RE-ZERO] key. [ 0 ], + [RE-ZERO] ProG C L E A R P L U? 3. Clear all item data. [ C ] ProG P L U C O U N T Reset Seqence Nmber to 0 1. Go to program mode. [MODE] + [RE- ZERO] ProG P L U C O U N T 1 0 Note) Press [MODE] key while pressing [RE-ZERO] key. Note) The 2 nd display shows the nmber of items that exist in memory. 2. Press [ + ] key [ + ] Note) The 2 nd display shows the existing seqence nmber in memory. SEq no 4 3. Reset Seqence No by [ 0 ] pressing [ 0 ] key SEq no 0 34
35 5.3. Review Item Code already in Memory 1. Go to program mode. [MODE] + [RE- ZERO] ProG P L U C O U N T 1 0 Note: Press [MODE] key while pressing [RE-ZERO] key. Note: The 2 nd display shows the nmber of items that exist in memory. 2. Press [ # ] key. [ # ] CH 1 A Check other item codes with [ C ] [ - ] and [ + ] key. CH 2 A Note) [ + ] key works to move to the next item code. [ - ] key works to be back to the previos item. 4. Back to the initial screen of [MODE] program mode. + [RE- ZERO] ProG P L U C O U N T
36 5.4. Date and Time 1. Go to program mode. [MODE] + [RE- ZERO] ProG P L U C O U N T 1 0 Note: Press [MODE] key while pressing [RE-ZERO] key. Note: The 2 nd display shows the nmber of items that exist in memory. 2. Press [ - ] key to display date [ - ] and time. 3. Press [ - ] key and again to [ - ] go to date entry mode. 21: 31: M O N EntEr D D M M Y Y 0 4. Enter date, month, and year [ 1 ], [ 8 ], data. [ 0 ], [ 2 ], [ 0 ], [ 0 ] EntEr i.e. 18 Feb 2000 D D M M Y Y Note: Each of two digit nmeric data represents date, month, and year. The order of Date, Time, Year (DDMMYY) can be changed by specification. 5. Press [ - ] key. [ - ] EntEr D A Y 0 - Contine - 36
37 6. Enter the day of the week. [ 4 ] EntEr i.e. Friday D A Y 4 Note: one digit nmeric data represents the day of the week as following table. Nmber Day of Week Nmber Day of Week 0 Monday 4 Friday 1 Tesday 5 Satrday 2 Wednesday 6 Snday 3 Thrsday 7. Press [ - ] key. [ - ] 8. Enter the crrent time. [ 2 ], [ 0 ], [ 5 ], [ 3 ] EntEr H H M M 0 EntEr i.e. 20: 53 D A Y Note: Each of two digit nmeric data represents hor and minte. 9. Store the data. [ ] ProG P L U C O U N T 1 0 Note: When pressing [ ] key, the internal clock starts to move from 00 second. 37
38 APENDIX I (LIST OF ASCII CODE) Code Chara. Code Chara. Code Chara. Code Chara. Code Chara. Code Chara. 20 Space P 60 ` 70 p 21! A 51 Q 61 a 71 q B 52 R 62 b 72 r 23 # C 53 S 63 c 73 s 24 $ D 54 T 64 d 74 t 25 % E 55 U 65 e & F 56 V 66 f 76 v G 57 W 67 g 77 w 28 ( H 58 X 68 h 78 x 29 ) I 59 Y 69 I 79 y 2A * 3A : 4A J 5A Z 6A j 7A z 2B + 3B ; 4B K 5B [ 6B k 7B { 2C, 3C < 4C L 5C \ 6C l 7C 2D - 3D = 4D M 5D ] 6D m 7D } 2E. 3E > 4E N 5E ^ 6E n 7E ~ 2F / 3F? 4F O 5F _ 6F o 7F 38
39 APENDIX II (LIST OF TERAOKA CODE) Code Chara. Code Chara. Code Chara. Code Chara. Code Chara. 00 Space 20 T A 21 U 41! B 22 V C 23 W 43 # D 24 X 44 $ E 25 Y 45 % F 26 Z 46 & G 27, 47 / H ( I ) J K Æ L Ä M Ø N Ö O Ã P Ê Q Á R S CR 39
40 DI-80 Limited Warranty Rice Lake Weighing Systems (RLWS) warrants that all RLWS eqipment and systems properly installed by a Distribtor or Original Eqipment Manfactrer (OEM) will operate per written specifications as confirmed by the Distribtor/OEM and accepted by RLWS. All systems and components are warranted against defects in materials and workmanship for two (2) years. RLWS warrants that the eqipment sold herender will conform to the crrent written specifications athorized by RLWS. RLWS warrants the eqipment against falty workmanship and defective materials. If any eqipment fails to conform to these warranties, RLWS will, at its option, repair or replace sch goods retrned within the warranty period sbject to the following conditions: Upon discovery by Byer of sch nonconformity, RLWS will be given prompt written notice with a detailed explanation of the alleged deficiencies. Individal electronic components retrned to RLWS for warranty prposes mst be packaged to prevent electrostatic discharge (ESD) damage in shipment. Packaging reqirements are listed in a pblication, Protecting Yor Components From Static Damage in Shipment, available from RLWS Eqipment Retrn Department. Examination of sch eqipment by RLWS confirms that the nonconformity actally exists, and was not cased by accident, misse, neglect, alteration, improper installation, improper repair or improper testing; RLWS shall be the sole jdge of all alleged non-conformities. Sch eqipment has not been modified, altered, or changed by any person other than RLWS or its dly athorized repair agents. RLWS will have a reasonable time to repair or replace the defective eqipment. Byer is responsible for shipping charges both ways. In no event will RLWS be responsible for travel time or on-location repairs, inclding assembly or disassembly of eqipment, nor will RLWS be liable for the cost of any repairs made by others. THESE WARRANTIES EXCLUDE ALL OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING WITHOUT LIMITATION WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. NEITHER RLWS NOR DISTRIBUTOR WILL, IN ANY EVENT, BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. RLWS AND BUYER AGREE THAT RLWS S SOLE AND EXCLUSIVE LIABILITY HEREUNDER IS LIMITED TO REPAIR OR REPLACEMENT OF SUCH GOODS. IN ACCEPTING THIS WARRANTY, THE BUYER WAIVES ANY AND ALL OTHER CLAIMS TO WARRANTY. SHOULD THE SELLER BE OTHER THAN RLWS, THE BUYER AGREES TO LOOK ONLY TO THE SELLER FOR WARRANTY CLAIMS. No terms, conditions, nderstanding, or agreements prporting to modify the terms of this warranty shall have any legal effect nless made in writing and signed by a corporate officer of RLWS and the Byer Rice Lake Weighing Systems, Inc. Rice Lake, WI USA. All Rights Reserved. RICE LAKE WEIGHING SYSTEMS 230 WEST COLEMAN STREET RICE LAKE, WISCONSIN USA 1
DMC-688. When Accuracy Counts
DMC-688 Money Counti ng Scal e When Accuracy Counts Operation Manual 73360 DMC- 688 SERIES OPERATING MANUAL SECTION INDEX PAGE NUMBER 1.0. GENERAL 1.1. Unlocking Procedure 1.2. Setting Up 2 3 2.0. SPECIFICATIONS
More informationBCD Interface for the 520 Indicator. Installation and Configuration Manual
BCD Interface for the 520 Indicator Installation and Configuration Manual 7627 Contents About This Manual....0 Introduction... 2.0 Installation... 2 2. BCD Option Card Installation.......................................................
More informationDI-80. When Accuracy Counts
DI-80 Indi cator When Accuracy Counts Service Manual 75591 GENERAL SPECIFICATION 1. GENERAL SPECIFICATION Model : DI 80 Dimension : 255 (L) X 240 (W) X 146 (H) Number Of Loadcells : max 2 x External Platform
More informationBCD Interface for the 520 Indicator DISCONTINUED. Installation and Configuration Manual Rev A
BCD Interface for the 520 Indicator Installation and Configuration Manual 76127 Rev A Contents About This Manual... 1 1.0 Introduction... 1 2.0 Installation... 2 2.1 BCD Option Card Installation.....................................................
More informationR-30 Price Computing Retail Scale. Version 2. Installation and Service Manual
R-30 Price Computing Retail Scale Version 2 Installation and Service Manual 64041 Contents About This Manual... 1 1.0 Introduction... 1 1.1 Start-up Self Check... 1 1.2 Power Supply... 1 1.3 Battery Replacement...
More informationPC 150. Digital Bench Scale. Operation Manual
PC 150 Digital Bench Scale Operation Manual Revision 1.2 September 14, 2000 1996-2000 Transcell Technology, Inc. Contents subject to change without notice. Transcell Technology, Inc. 35 Waltz Drive Wheeling,
More informationDVR 630/650 Series. Video DVR 630/650 Series. 8/16-Channel real-time recording with CIF resolution. Flexible viewing with two monitor outputs
Video DVR 630/650 Series DVR 630/650 Series 8/16-Channel real-time recording with resoltion Flexible viewing with two monitor otpts Remote viewing, playback, control, and configration Easy Pan/Tilt/Zoom
More informationIQ6200/6500 Counting Scales. Installation Manual
IQ6200/6500 Counting Scales Installation Manual 32224 Contents About this Manual... 1 1.0 Introduction... 1 1.1 Scale Resolution... 2 1.2 Choosing the Best Sample... 2 2.0 Installation and Start-Up...
More informationEMC ViPR. User Guide. Version
EMC ViPR Version 1.1.0 User Gide 302-000-481 01 Copyright 2013-2014 EMC Corporation. All rights reserved. Pblished in USA. Pblished Febrary, 2014 EMC believes the information in this pblication is accrate
More informationPC-150. DIGITAL BENCH SCALE Setup / Operation Manual
PC-150 DIGITAL BENCH SCALE Setup / Operation Manual Revision 1.3 975 Deerfield Parkway Buffalo Grove, IL 60089 October 6, 2010 Tel (847) 419-9180 Fax (847) 419-1515 http://www.transcell.com 1 ATTENTION:
More informationOperation Instructions
RL150-10-7 Digital Floor Level Scale 150-10-7 Software Revision 11439 Operation Instructions 131994 - Rev A Contents 1.0 Introduction... 1 2.0 Safety... 2 2.1 Safety Signals...................................................................
More informationCS Series. Digital Counting Scale. Operation Manual
CS Series Digital Counting Scale Operation Manual Revision 1.0 October 31, 1994 1994 Transcell Technology, Inc. Contents subject to change without notice. Transcell Technology, Inc. 975 Deerfield Parkway
More informationNortel DECT Handset 4025 User Guide
DECT 4025 Nortel DECT Handset 4025 User Gide Revision history Revision history October 2005 Standard 2.00. This docment is p-issed to spport Nortel Commnication Server 1000 Release 4.5. Febrary 2005 Standard
More informationLTC 8600 Series Allegiant Matrix/Control Systems - Modular
Video 86 Series Allegiant Matrix/Control Systems - Modlar 86 Series Allegiant Matrix/Control Systems - Modlar www.boschsecrity.com 128 Camera by 16 monitor switching Modlar constrction Powerfl alarm handling
More informationFiber Optic Media Converters
Video iber Optic edia Converters iber Optic edia Converters Utilizes Small orm-factor Plggable (SP) modles lti-mode and single-mode modles available Spports distances p to 20 km (12.4 miles) Srface mont
More informationStandard. 8029HEPTA DataCenter. Because every fraction of a second counts. network synchronization requiring minimum space. hopf Elektronik GmbH
8029HEPTA DataCenter Standard Becase every fraction of a second conts network synchronization reqiring minimm space hopf Elektronik GmbH Nottebohmstraße 41 58511 Lüdenscheid Germany Phone: +49 (0)2351
More informationLocal Run Manager Generate FASTQ Analysis Module
Local Rn Manager Generate FASTQ Analysis Modle Workflow Gide For Research Use Only. Not for se in diagnostic procedres. Overview 3 Set Parameters 3 Analysis Methods 5 View Analysis Reslts 5 Analysis Report
More informationDI-10. When Accuracy Counts
DI-1 Check Wei ghi ng Scal e When Accuracy Counts Service Manual 73355 1 CONTETS PAGE 1. 2. 3. 4. 5. 6. 7. a. EXTERNAL VIEW........................... 2 DISPLAY & KEYS.......................... 2 2-1.
More informationContent Safety Precaution... 4 Getting started... 7 Input method... 9 Using the Menus Use of USB Maintenance & Safety...
STAR -1- Content 1. Safety Precation... 4 2. Getting started... 7 Installing the cards and the Battery... 7 Charging the Battery... 8 3. Inpt method... 9 To Shift Entry Methods... 9 Nmeric and English
More informationI/O Module. For Intrinsically Safe Systems Version 2.0. Installation Manual
I/O Module For Intrinsically Safe Systems Version 2.0 Installation Manual 78076 Contents.0 Introduction... 2.0 Installation... 2 2. Unpacking and Assembly........................................................
More informationLTC 8500 Series Allegiant Matrix/Control Systems - Modular
Video LTC 85 Series Allegiant Matrix/Control Systems - Modlar LTC 85 Series Allegiant Matrix/Control Systems - Modlar www.boschsecrity.com 64 Camera by 8 monitor switching 8 Independent keyboards Modlar
More informationCrane Scale. Revision 1.4 February 18, Transcell Technology, Inc. Contents subject to change without notice.
CR-500 Crane Scale Setup / Operation Manual Revision 1.4 February 18, 2003 2003 Transcell Technology, Inc. Contents subject to change without notice. Transcell Technology, Inc. 975 Deerfield Parkway Buffalo
More informationLTC 8500 Series Allegiant Matrix/Control Systems - Modular
Video LTC 85 Series Allegiant Matrix/Control Systems - Modlar LTC 85 Series Allegiant Matrix/Control Systems - Modlar www.boschsecrity.com 64 Camera by 8 monitor switching 8 Independent keyboards Modlar
More informationModel 500 Digital Weight Indicator
Rev. 1.10 Serial Number: Model 500 Digital Weight Indicator USER MANUAL 1992-2000, Reliable Scale Corporation Reliable Scale Corporation 520 Moraine Road NE Calgary, Alberta, Canada Tel:1-800-419-1189
More informationProgrammable HMI Indicator/Controller. In-Motion Checkweighing System Manual
Programmable HMI Indicator/Controller In-Motion Checkweighing System Manual 103244 Contents About This Manual... 1 1.0 Introduction and System Setup... 1 1.1 Hardware Requirements..........................................................
More information21e Multi-Function Indicator
21e Multi-Function Indicator 21e is built to answer the needs of highly demanding applications in the aspect of transaction & data speed, number of peripheral connection, management data & security, flexibility
More information1. Basic safety information 3 2. Proper use 3
0 6 12 18 24 0 6 12 18 24 307262 01 4 5 6 C2 0,5mm 2-2,5mm 2 8mm 230-240V~ 50-60Hz R 10a -30T 0,5mm 2-2,5mm 2 8mm 230-240V~ 50-60Hz R 10a -30T EN Time switch DV1K 108272 DV2K 108273 MENU OK 1 C1 16(10)A
More informationLocal Run Manager. Software Reference Guide for MiSeqDx
Local Rn Manager Software Reference Gide for MiSeqDx Local Rn Manager Overview 3 Dashboard Overview 4 Administrative Settings and Tasks 7 Workflow Overview 12 Technical Assistance 17 Docment # 1000000011880
More informationCOIN COUNTING SCALE TC-290 SERIES. Count Any Coin, Any Quantity, Anywhere, In Three Seconds Accurately!
TC-290 SERIES COIN COUNTING SCALE TC-290 Single Coin Counting Scale Light Tower TC-292 Dual Coin Counting Scale Count Any Coin, Any Quantity, Anywhere, In Three Seconds Accurately! High counting & weight
More informationPS-IN202 Weighing Indicator User Manual
PS-IN202 Weighing Indicator User Manual Version 2015.05 Contents FRONT AND REAR VIEW OF THE INDICATOR CHAPTER 1 CONNECTIONS 1.1 WHAT'S IN THE BOX 1.2 CONNECTING TO THE WEIGH PLATFORM 1.3 CONNECTION TO
More informationChapter 6: Pipelining
CSE 322 COPUTER ARCHITECTURE II Chapter 6: Pipelining Chapter 6: Pipelining Febrary 10, 2000 1 Clothes Washing CSE 322 COPUTER ARCHITECTURE II The Assembly Line Accmlate dirty clothes in hamper Place in
More informationDSCUSB Standard User Manual. mantracourt.com DSCUSB. Digital Sensor Card USB Strain Gauge Input
DSCUSB Standard User Manual mantracourt.com DSCUSB Digital Sensor Card USB Strain Gauge Input Contents Chapter 1 Introduction...2 Overview... 2 Manual Scope... 2 LED Status Indication... 2 Chapter 2 Getting
More informationAccess Professional Edition 2.1
Engineered Soltions Access Professional Edition 2.1 Access Professional Edition 2.1 www.boschsecrity.com Compact access control based on Bosch s innovative AMC controller family Integrated Video Verification
More informationThe extra single-cycle adders
lticycle Datapath As an added bons, we can eliminate some of the etra hardware from the single-cycle path. We will restrict orselves to sing each fnctional nit once per cycle, jst like before. Bt since
More information1. Basic safety information 4 2. Proper use 4
307075 EN Time switch TR 611 top2 6110100 TR 622 top2 6220100 1. Basic safety information 4 2. Proper se 4 Disposal 4 3. Installation and connection 5 Monting the time switch 5 Connecting the cable 7 Disconnecting
More informationKW serial. User s guide. Bench Scales UGKW-E0302
KW serial Bench Scales User s guide UGKW-E0302 KW serial bench scale user s manual Table of Contents SECTION 1 INTRODUCTION 1 SECTION 2 SPECIFICATIONS.. 2 SECTION 3 INSTALLATION.3 SECTION 4 KEY DESCRIPTIONS
More informationDIVAR IP U. Video DIVAR IP U.
Video DIVAR IP 7000 3U DIVAR IP 7000 3U www.boschsecrity.com RAID-5 protected (standard configration), all-in-one video management soltion for p to 128 channels Ot-of-the-box IP video management soltion
More informationDIVAR IP U. Video DIVAR IP U.
Video DIVAR IP 7000 2U DIVAR IP 7000 2U www.boschsecrity.com RAID-5 protected (standard configration), all-in-one video management soltion for p to 128 channels Ot-of-the-box IP video management soltion
More informationCAPL Scripting Quickstart
CAPL Scripting Qickstart CAPL (Commnication Access Programming Langage) For CANalyzer and CANoe V1.01 2015-12-03 Agenda Important information before getting started 3 Visal Seqencer (GUI based programming
More informationOperating Bulletin MODBUS-RTU. The Fastest Flow Controller Company in the World!
Operating Bulletin MODBUS-RTU The Fastest Flow Controller Company in the World! 1 Notice: Alicat Scientific, Inc. reserves the right to make any changes and improvements to the products described in this
More information1. Introduction Page 2. Specifications Page Installation Page Key Functions Page Operations Page 6. Check Weighing Page 6
Contents: 1. Introduction Page 2 Specifications Page 2 2. Installation Page 3 3. Key Functions Page 4 4. Operations Page 6 Check Weighing Page 6 Accumulation Page 7 Parts Counting Page 7 Print (RS232C)
More informationDC-190. When Accuracy Counts
DC-190 Counti ng Scal e When Accuracy Counts Operation Manual 73352 CONTENT 1. General Specification 1 2. Overall Dimension 2.1 DC 190 Indicator 2 2.2 S-X Platform 2 2.3 Pole Type 3 2.4 Bench Type 4 3.
More informationDIVAR hybrid 5000 recorder
Video DIVAR hybrid 5000 recorder DIVAR hybrid 5000 recorder www.boschsecrity.com APP H.265 Hybrid recording of p to 16 IP and 16 analog channels Extended rack-mont nit with advanced connections 12 MP IP
More informationVEZ-400 Mini PTZ Dome
Video VEZ-400 Mini PTZ Dome VEZ-400 Mini PTZ Dome www.boschsecrity.com Tre day/night camera with 26X optical zoom 600 TVL resoltion Wide Dynamic Range (WDR) Compact, vandal-resistant (IK10 rated) enclosre
More informationDIVAR IP U. Video DIVAR IP U.
Video DIVAR IP 6000 2U DIVAR IP 6000 2U RAID-5 protected (standard configration), all-in-one recording soltion for p to 128 channels Pre-installed, pre-configred IP storage soltion with p to 32 TB storage
More informationTC1880 Series. 4/5/6/8 Channel RS-232 FIBER OPTIC MICRO MUX User's Manual
Series 4/5/6/8 Channel RS-232 FIBER OPTIC MICRO MUX MODEL: S/N: DATE: Notice! Although every effort has been made to insure that this manual is current and accurate as of date of publication, no guarantee
More informationFeatures. ICMS Integrated Corrosion Management System
ICMS Integrated Corrosion System Featres Total Corrosion Data Data Exhange with DCS/PCS/SCADA Systems Correlate Corrosion & Process Data Enables Highly Cost-Effective Asset Designed Specifically for Corrosion
More informationDTT Series Digital Torque Testers User Manual
for DTT Models above Serial Number: 2000 15700 S. Waterloo Road Cleveland, OH 44110-3898 Phone: (888) 486-6163 Fax: (216) 481-4519 2017 Jergens, Inc. All Rights Reserved Revision Date: 02/19/18 Email:
More informationDSA E-Series 4TB (E2700)
Video DSA E-Series 4TB (E2700) DSA E-Series 4TB (E2700) Scale-p network storage soltion: controller nit with 12 internal HDDs expandable via state-of-theart SAS interface-connected expansion nits Configrable
More informationdss-ip Manual digitalstrom Server-IP Operation & Settings
dss-ip digitalstrom Server-IP Manal Operation & Settings Table of Contents digitalstrom Table of Contents 1 Fnction and Intended Use... 3 1.1 Setting p, Calling p and Operating... 3 1.2 Reqirements...
More informationDIVAR IP U. Video DIVAR IP U.
Video DIVAR IP 6000 3U DIVAR IP 6000 3U www.boschsecrity.com RAID-5 protected (standard configration), all-in-one recording soltion for p to 128 channels Pre-installed, pre-configred IP storage soltion
More informationCOBALT C INSTALLATION GUIDE RFID CONTROLLER ESCORT MEMORY SYSTEMS. High Frequency Passive Radio Frequency Identification Controller
ESCORT MEMORY SYSTEMS COBALT C0405-232-01 RFID CONTROLLER High Frequency Passive Radio Frequency Identification Controller INSTALLATION GUIDE How to Install and Configure Escort Memory Systems Cobalt C0405-232-01
More informationDivar Digital Video Recorder
Video Divar Digital Video Recorder Divar Digital Video Recorder 6, 9, and 16channel versions Bilinx commnication optional Simltaneos recording, playback & archiving AtoDome control Smart motion search
More informationPSD Strain Gauge or Load Cell Hand Held Display TEDS enabled
TEDS Enabled TEDS enabled 2 label options available for the PSD PSD Strain Gauge or Load Cell Hand Held Display TEDS enabled User Manual www.mantracourt.co.uk What is TEDS?...2 Basic concept...2 How it
More informationEASON TECHNOLOGY. IO8 & IO24 Break-Out Module
EASON TECHNOLOGY IO8 & IO24 Break-Out Module p/n 50-00180-01 Revision1.2 Eason Technology, Inc. 7975 Cameron Dr. Bldg 300 Windsor, CA 95492 Phone (707) 837-0120 FAX (707) 837-2742 http://www.eason.com
More informationWhat s New in AppSense Management Suite Version 7.0?
What s New in AMS V7.0 What s New in AppSense Management Site Version 7.0? AppSense Management Site Version 7.0 is the latest version of the AppSense prodct range and comprises three prodct components,
More informationEMC VNX Series. Problem Resolution Roadmap for VNX with ESRS for VNX and Connect Home. Version VNX1, VNX2 P/N REV. 03
EMC VNX Series Version VNX1, VNX2 Problem Resoltion Roadmap for VNX with ESRS for VNX and Connect Home P/N 300-014-335 REV. 03 Copyright 2012-2014 EMC Corporation. All rights reserved. Pblished in USA.
More informationDIVAR IP U. Video DIVAR IP U.
Video DIVAR IP 7000 3U DIVAR IP 7000 3U www.boschsecrity.com RAID-5 protected (standard configration), all-in-one video management soltion for p to 128 channels Ot-of-the-box IP video management soltion
More informationComputer User s Guide 4.0
Compter User s Gide 4.0 2001 Glenn A. Miller, All rights reserved 2 The SASSI Compter User s Gide 4.0 Table of Contents Chapter 1 Introdction...3 Chapter 2 Installation and Start Up...5 System Reqirements
More informationIsilon InsightIQ. Version 2.5. User Guide
Isilon InsightIQ Version 2.5 User Gide Pblished March, 2014 Copyright 2010-2014 EMC Corporation. All rights reserved. EMC believes the information in this pblication is accrate as of its pblication date.
More informationHardware Design Tips. Outline
Hardware Design Tips EE 36 University of Hawaii EE 36 Fall 23 University of Hawaii Otline Verilog: some sbleties Simlators Test Benching Implementing the IPS Actally a simplified 6 bit version EE 36 Fall
More informationDRAFT. Customer site gravity factor. Filtering parameters. Five points for linearity correction to ensure maximum accuracy
Avery Weigh-Tronix Technical Specification Description General This specification describes the indicator, capable of stand-alone operation, or of integration into a larger system via serial interface.
More informationUWE-1707 SERIES CONTENTS OPERATION MANUAL ELECTRONIC WEIGHING INDICATOR 1. SPECIFICATIONS 2. INSTALLATION
UWE-1707 SERIES CONTENTS ELECTRONIC WEIGHING INDICATOR OPERATION MANUAL 1. SPECIFICATIONS PLEASE READ THIS MANUAL VERY CAREFULLY BEFORE ATTEMPT TO OPERATE THE SCALE 2. INSTALLATION 3. ROUTINE OPERATION
More informationTable of Contents. User Manual. DS-201 Solar Web Monitor
Table of Contents User Manual DS-201 Solar Web Monitor Installation.... 1 Step 1 Unpack and identify all Cables Step 2 Verify Serial Communication Setup Step 3 Plug in Communications Cable to Controller
More informationPRODUCT CONTENTS... 3 II. REQUIRED MATERIALS... 3 III. OVERVIEW... 3 IV. BENCH LAYOUT...
IR-510 Bench 2012 Infrared Industries, Inc. 25590 Seaboard Lane Hayward, CA 94545 Toll-free phone 800.344.0321 Phone 510.782.8100 Fax 510.782.8101 www.infraredindustries.com Table of Contents I. PRODUCT
More informationThe single-cycle design from last time
lticycle path Last time we saw a single-cycle path and control nit for or simple IPS-based instrction set. A mlticycle processor fies some shortcomings in the single-cycle CPU. Faster instrctions are not
More informationAUTOMATION. Operator s Manual. PG5 Digital Pressure Gauge
AUTOMATION P R O D U C T S GROUP, INC. Operator s Manual PG5 Digital Pressure Gauge DOC. 9003264 Rev. A1 3/10 Tel: 1/888/525-7300 Fax: 1/435/753-7490 www.apgsensors.com E-mail: sales@apgsensors.com PG5
More informationIR-Corrected Zoom and Varifocal Lenses
Video IR-Corrected Zoom and Varifocal Lenses IR-Corrected Zoom and Varifocal Lenses www.boschsecrity.com IR for operation with high performance day/night and monochrome cameras 1/3-inch and 1/2-inch formats
More informationL EGAL NOTICES. ScanSoft, Inc. 9 Centennial Drive Peabody, MA 01960, United States of America
L EGAL NOTICES Copyright 2002 by ScanSoft, Inc. All rights reserved. No part of this pblication may be transmitted, transcribed, reprodced, stored in any retrieval system or translated into any langage
More informationOCEAN WATERPROOF WEIGHING SCALE USER MANUAL
OCEAN WATERPROOF WEIGHING SCALE USER MANUAL Excell Precision Limited 2006. All rights reserved Worldwide. The information contained herein is the property of Excell Precision Limited and is supplied without
More informationGMC-206/215/230 Digital Desktop Weighing Scale Operation Manual
GMC-206/215/230 Digital Desktop Weighing Scale Operation Manual Version 2.1 Gamma Scale Tel: (905) 455-8333 Fax: (905) 455-0658 E-mail: info@gammascale.com Website: www.gammascale.com 1. Technical Parameters
More informationReview. A single-cycle MIPS processor
Review If three instrctions have opcodes, 7 and 5 are they all of the same type? If we were to add an instrction to IPS of the form OD $t, $t2, $t3, which performs $t = $t2 OD $t3, what wold be its opcode?
More informationModel SRV945-BT 24 X 36 Platform Scale App-Enabled Operating and Service Manual Part No.: MAN945-BT_ Page 1 of 16.
Part No.: MAN945-BT_180417 Page 1 of 16 S by S Instruments, Inc. Model SRV945-BT Portable Platform Scale App Enabled Wireless Operating and Service Manual Part No.: MAN945-BT_180417 Page 2 of 16 TABLE
More informationDigital Scale. Operation Manual. Revision 1.1 April 16, Transcell Technology, Inc. Contents subject to change without notice.
EL 3000 Digital Scale Operation Manual Revision 1.1 April 16, 2002 1995-2002 Transcell Technology, Inc. Contents subject to change without notice. Transcell Technology, Inc. 975 Deerfield Parkway Buffalo
More informationInstallation / Operator / Service Manual. Bench Scales Revision 6 07/ by Fairbanks Scales Inc. All rights reserved
Installation / Operator / Service Manual Bench Scales 2005-2010 by Fairbanks Scales Inc. All rights reserved 50778 Revision 6 07/10 Amendment Record 50778 Manufactured by Fairbanks Scales Inc. 821 Locust
More informationSY021 Portable Load/Force Meter User instructions
SY021 Portable Load/Force Meter User instructions Relates to firmware version 5.2 INTRODUCTION The SY021 is a portable load meter, which can indicate the load present on any attached cell. A dual channel
More informationDIVAR IP Video DIVAR IP Remote viewing via Video Security App and Video Security Client from Bosch
Video DIVAR IP 5000 DIVAR IP 5000 www.boschsecrity.com Remote viewing via Video Secrity App and Video Secrity Client from Bosch Flly featred video recording soltion for p to 32 channels Ot-of-the-box IP
More informationICMS3 Integrated Corrosion Management System
Integrated System Featres Total Data Data Exhange with DCS/PCS/SCADA Systems Correlate & Process Data Enables Highly Cost-Effective Asset Designed Specifically for Personnel Fll Client- Operation The Integrated
More informationNorth American Service Manual
North American Service Manual MODEL PC SERIES Version 2 March 25, 1997 Revision B1.1 April 4, 2000 Prepared by TRANSCELL TECHNOLOGY, INC. TABLE OF CONTENTS Page Chapter 1: Introduction... 1-1 Chapter 2:
More informationReview Multicycle: What is Happening. Controlling The Multicycle Design
Review lticycle: What is Happening Reslt Zero Op SrcA SrcB Registers Reg Address emory em Data Sign etend Shift left Sorce A B Ot [-6] [5-] [-6] [5-] [5-] Instrction emory IR RegDst emtoreg IorD em em
More informationNetworks An introduction to microcomputer networking concepts
Behavior Research Methods& Instrmentation 1978, Vol 10 (4),522-526 Networks An introdction to microcompter networking concepts RALPH WALLACE and RICHARD N. JOHNSON GA TX, Chicago, Illinois60648 and JAMES
More informationUnit Testing with VectorCAST and AUTOSAR
Unit Testing with VectorCAST and AUTOSAR Vector TechDay Software Testing with VectorCAST V1.0 2018-11-15 Agenda Introdction Unit Testing Demo Working with AUTOSAR Generated Code Unit Testing AUTOSAR SWCs
More informationclick DuoFix screwless Plug-in screwless terminal NC contact Test tap
307098 Time switch installation EN Astro Time Switch SELEKTA 170 top2 1700100 1. Basic safety information WARNING Danger of death from electric shock or fire! ¾Installation shold only be carried ot by
More informationDIVAR network IP recorder
Video DIVAR network 2000 8IP recorder DIVAR network 2000 8IP recorder www.boschsecrity.com 8 IP channels with 256 Mbps incoming 8 MP (UHD) IP camera spport for view and playback Real time live display
More informationEMC AppSync. User Guide. Version REV 01
EMC AppSync Version 1.5.0 User Gide 300-999-948 REV 01 Copyright 2012-2013 EMC Corporation. All rights reserved. Pblished in USA. EMC believes the information in this pblication is accrate as of its pblication
More informationDWP-PC SERIES PRICE COMPUTING SCALE User s Guide
DWP-PC SERIES PRICE COMPUTING SCALE User s Guide PLEASE READ THIS MANUAL VERY CAREFULLY BEFORE ATTEMPT TO OPERATE THE INSTRUMENT Specifications subject to change without prior notice CONTENTS 1. INSTALLATION
More informationRangerBOSS Network Ready Constant Monitor Model CM2800
RangerBOSS Network Ready Constant Monitor Model CM2800 Instruction Manual Contents 1 Description CM2800 1 Features 1 2 Installation Installation Instructions 2 Installation Diagram 3 3 Operation Wrist
More informationLCI Load Cell Junction Box with Fault Monitor
LCI Load Cell Junction Box with Fault Monitor User Manual www.mantracourt.co.uk The LCI Load Cell Failure Alarm Manual Chapter 1 Introduction to the LCI...2 Chapter 2 Installing the LCI...3 Figure 2.1
More informationDigital Counting Scale. Revision 2.4 October 20, Transcell Technology, Inc. Contents subject to change without notice.
TC-2001 Series Digital Counting Scale Setup & Operation Manual Revision 2.4 October 20, 2003 2001-2003 Transcell Technology, Inc. Contents subject to change without notice. Transcell Technology, Inc. 975
More information!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
"#$%&"'()*#%&+,"-)&./&+ SECTP-E0403 Contents SECTION 1 INTRODUCTION...... 1 1. 1 Figures...1 1. 2 Specifications.... 1 1. 3 Dimension..1 SECTION 2 KEYBOARD DESCRIPTIONS...2 SECTION 3 OPERATION.....3 3.
More informationCOMPLETE MANUAL. WEIGHING INDICATOR TI-1200 and TI-1200-S TI-1200 with rechargeable battery.
COMPLETE MANUAL WEIGHING INDICATOR TI-1200 and TI-1200-S TI-1200 with rechargeable battery. TI-1200-S without rechargeable battery and with a smaller cabinet. Note: When TI-1200 is shipped as a part of
More informationPV3500. Fuel Site Controller. Service Manual OPW Fuel Management Systems Manual M Rev. 1
PV3500 Fuel Site Controller Service Manual 2002 OPW Fuel Management Systems Manual M11-00.03 Rev. 1 OPW Fuel Management Systems - System and Replacement Parts Warranty Statement Effective September 1,
More informationCS 251, Winter 2019, Assignment % of course mark
CS 25, Winter 29, Assignment.. 3% of corse mark De Wednesday, arch 3th, 5:3P Lates accepted ntil Thrsday arch th, pm with a 5% penalty. (7 points) In the diagram below, the mlticycle compter from the corse
More information1. Basic safety information 4 2. Proper use 4
8mm 0 6 12 18 24 µ 307263 01 L N EN Astro Time Switch ASTRO1K 108274 0,5mm 2-2,5mm 2 MENU 16(10)A 250V~ 230-240V~ 50-60Hz R 10a -30T OK 1 2 3 1. Basic safety information 4 2. Proper se 4 Disposal 4 3.
More informationReview: Computer Organization
Review: Compter Organization Pipelining Chans Y Landry Eample Landry Eample Ann, Brian, Cathy, Dave each have one load of clothes to wash, dry, and fold Washer takes 3 mintes A B C D Dryer takes 3 mintes
More informationAUTOMATION. Operator s Manual PG-5. Full Access. DOC Rev. A1 3/10
AUTOMATION P R O D U C T S G R O U P, I N C. Operator s Manual PG-5 Full Access DOC. 9003384 Rev. A1 3/10 Tel: 1/888/525-7300 Fax: 1/435/753-7490 www.apgsensors.com E-mail: sales@apgsensors.com PG5 Rev.
More informationVIP X16 XF E Video Encoder
Video VIP X16 XF E Video Encoder VIP X16 XF E Video Encoder www.boschsecrity.com 16 video inpt channels with Dal Streaming Deinterlacing at video inpt and progressive encoding Network-attached iscsi recording
More informationDIVAR hybrid 5000 recorder
Video DIVAR hybrid 5000 recorder DIVAR hybrid 5000 recorder www.boschsecrity.com APP H.265 Hybrid recording of p to 16 IP and 16 analog channels Extended rack-mont nit with advanced connections 12 MP IP
More informationEtherNet/IP. Interface for 520 and 920i Indicators. Installation and Programming Manual
EtherNet/IP Interface for 520 and 920i Indicators Installation and Programming Manual 88537 Contents About This Manual... 1 1.0 Introduction... 1 2.0 Installation... 2 2.1 Installing the EtherNet/IP Interface...................................................
More informationPennsylvania Scale Company Model 400B Battery Powered Digital Indicator Operation & Calibration Manual
Pennsylvania Scale Company Model 400B Battery Powered Digital Indicator Operation & Calibration Manual Pennsylvania Scale Company 1042 New Holland Avenue Lancaster PA 17601 For online interactive tech
More information