Table of Contents LJ-NA02. Setting Manual Network Adaptor

Transcription

1 P40A Setting Manual Network Adaptor Model No. LJ-NA02 Table of Contents 1. Part names Connection diagram when configuring Before setup Setup Network adaptor registration Reference: 7-SEG LED error code Reset work Factory Reset work Thank you for purchasing a Panasonic product. -Before setting the system, please read this documentation. -For future reference, please keep this manual in a safe place. -Even if the product fails within the warranty period due to nonconforming to the Setting Manual, the User s Manual, and the caution labels attached to the product, we will not repair it free of charge. Notice: Microsoft, Windows, Microsoft windows 7, Microsoft Windows 8.1 are trademarks of Microsoft Corporation in the United States and or other countries. Printed in Japan

2 1. Part names Communication unit 7-SEG LED Power LED Power ON ON Power OFF OFF LAN (LINK/ACT) LED It represents the connection to the LAN. It represents the state of transmission and reception of data Status button RJ-45 Modular jack Status LED Power LED Power ON ON Power OFF OFF COM terminal Wiring hole Power cable Power supply unit Power LED Power ON ON Power OFF OFF Terminal (The inside) Terminal cover Status button Status LED S3 LED EMS LED COM LED S2 LED S1 LED RESET button SET button STATUS button MODE button How the displayed LEDs are represented in this manual. The on, flashing, and off states of the LEDs are represented as follows. 2 On Off Flashing

3 2. Connection diagram when configuring the network adaptor In your house Meter Grid 1Φ2W 230V Distribution board Servers operated by Utility CT 1Φ2W 230V 1Φ2W 230V External server RS485 LAN Broadband router Internet LJ-SK84A 1Φ2W 230V LJ-NA02 PC (Windows 7, Windows 8.1) LAN cable (3m~) Materials to configure the network adaptor LJ-SK84A: Lithium-ion storage battery system This system is equipped with three battery modules. This product incorporates a network adaptor that is connected to the external server of the utility via the Internet. This system automatically updates its charging/discharging schedule based on instructions from the utility. In the event of a power failure, you can use the stored electrical power via a Back-up Socket-outlet. LJ-NA02:Network adaptor The network adaptor facilitates the communications between the demand response server and the lithium-ion storage battery system (LJ-SK84A) to update the charging/discharging schedule and/or send information on the state of the stored electrical power. 3

4 3. Before setup The network adaptor is configured by connecting it to the configuration PC with a LAN cable. Before configuring the network adaptor, please configure the PC's network settings with the following procedure. NOTICE This procedure assumes that you will be using Microsoft Windows 7, Microsoft Windows 8.1, but you can use a PC with another OS by configuring the corresponding settings Click "start button" at the bottom of the screen, then select "Control Panel" * 1 NOTICE Windows 8.1: In order to display the Control Panel, please right-click the Start button on after switching to the desktop screen Click "View network status and tasks". * 3 3 * 3-3. Click "Change adapter settings"

5 3-4. The "Local Area Connection" icon is displayed. Right-click the icon and select "Properties". * Select "Internet Protocol Version 4 (TCP/IPv4)", then click the "Properties" button. * Set the IP address and subnet mask as shown in the image, then click the "OK" button * 8 9 IP Address : Subnet mask : Leave all fields blank except those above NOTICE We recommend you write down the original network settings. 5

6 4. Setup 4-1 Check before setup Remove the network adaptor cover, check that the inside power LEDs are on, and check that the network adaptor's power supply has been turned on. (3 locations) Check that nothing is connected to the network adaptor's RJ-45 modular jack. Connect the configuration PC after configuring the mode setting. Power LED Power LED RJ-45 Modular jack Power LED 4-2 Set expert mode Set the network adaptor to expert mode with the following procedure. (1) Press and hold the "RESET" button for 2 seconds or longer to restart the network adaptor. (2) When the 7-SEG LED displays "88" and the network adaptor has restarted, immediately release the "RESET", then press and hold both the "SET" button and the "MODE" button for 2 seconds or longer. (2) 7-SEG LED = "88" (1) Press the "RESET" button (2sec~) Release the "RESET" button Press the "SET" + "MODE" button (2sec~) 6

7 (3) When set to expert mode, the "S3" LED turns on. Release the "SET" button and the "MODE" button. If not set to expert mode, repeat the procedure from (1). 4-3 Network settings for the network adaptor Configure the settings for connecting the network adaptor to the PC. (1) Press and hold the "MODE" button for 2 seconds or longer. (2) When the 7-SEG displays a flashing "IP", release the button. (2) 7-SEG LED = "IP" (1) Press the "MODE" button (2sec~) (3) Within 5 minutes, press and hold the "MODE" button again for 2 seconds or longer. (4) When the 7-SEG displays "IP", release the button. (4) 7-SEG LED = "IP" (3) Press the "MODE" button (2sec~) 7

8 4-4 Connection settings to the server Configure the settings for connecting the network adaptor to the server. In Web browser, if the screen of each step is not displayed correctly, click the web browser's reload button or repeat the steps again from step(2). (1) Connect the network adaptor and the PC with a LAN cable. (2) Start the web browser on the PC, enter in the address bar, and press the Enter key. NOTICE You must be disabled if you have enabled the PROXY setting of the Web browser. (3) The network adaptor's configuration screen is displayed, click the "Network" button. (4) The "Network Setting" screen is displayed. Enter the DHCP and server URL fields as shown in the image, then click the "OK" button. *DHCP will use the ON (mode 2). NOTICE Please enter the server URL according to the information from the utility power company. * Note the input mistake of the URL. When the network adaptor can not be connected to the router, you can be in "OFF" the DHCP. In this case, enter the value of Network adaptor in the column of IP Address. In addition, IP address should not be overlapped with other equipment. 8

9 (5) The following confirmation dialog box is displayed. Click the "OK" button. NOTICE This message will vary depending on the DHCP mode. (6) The web browser on the PC will display the following popup dialog box. Click the "OK" button. NOTICE If this screen does not appear, it does not enable the setting. Please repeat the steps again from step(2). (7) The network adaptor's 7-SEG LED display will change to a flashing "St". Within 5 minutes, press and hold the "MODE" button on the network adaptor for 2 seconds. (8) When the 7-SEG LED display changes to "IP", the settings have been stored in the network adaptor and expert mode ends. (9) The network adaptor will automatically restart after this. (7) 7-SEG LED = "St" (8) 7-SEG LED = "IP" Press the "MODE" button (2sec~) 9

10 4-5 Operation check This concludes network adaptor setup. Disconnect the LAN cable connected to the PC, connect the network adaptor to the broadband router with a LAN cable, and check network adaptor operation with the following procedure. NOTICE The broadband router that the network adaptor will be connected to must be set to DHCP mode. For the setup method, check the manual for the broadband router that will be used. Power of broadband router must be set to ON to 10 minutes before the operation check. The broadband router must be connected to the Internet. (1) Start the Lithium-ion storage battery system. (2) If the network adaptor and the Lithium-ion storage battery system are communicating correctly, the "COM" LED turns on as shown below. In this case, 7-SEG LED displays the "A31" indicating an unregistered in the server. (3) If the network adaptor and the broadband router are communicating correctly, the "EMS" LED is flashing. (4) If the display of the 7-SEG LED and "EMS" LED is different from the (3), please check the network adapter settings again. (5) If an error code other than "A31" is displayed on the 7-SEG LED, please refer to the 6. Error code table. Also check that the communication wire have been correctly connected and that there are no problems with the Lithium-ion storage battery system and broadband router settings. (6) If the router is not connected when the network adaptor is restarted, network adaptor tries to connect to the server after 30 minutes. In this case, it will display a A21" on the 7-SEG LED. If you want to connect to the server immediately, press the SET button for more than two seconds. "COM" LED = on "EMS" LED = flashing 7-SEG LED = "A" 7-SEG LED = "31" Error code A31 10

11 5. Network adaptor registration When the network adaptor can communicate via the external server by the Utility, it starts sending a registration request to the server. Please perform registration with the following procedure. (1) Contact the utility power company and request network adaptor registration. In doing so, you will need to tell the utility power company the serial number of each unit in the system. Check by referring to the installation manual for the lithium-ion storage battery system. The network adaptor serial number is written on the serial number label on the bottom of the network adaptor. LJ-NA02 S-No. E LJ-NA02 S-No. E Serial Number Serial Number Model name Model No. Serial No. Lithium-ion storage battery system Lithium-ion storage battery 1 Lithium-ion storage battery 2 Lithium-ion storage battery 3 Network Adaptor LJ-SK84A LJ-SBK01 LJ-SBK01 LJ-SBK01 LJ-NA02 11

12 (2) After you confirm that the network adaptor has been registered on the server side of the utility power company, press and hold the "SET" button on the network adaptor for 2 seconds or longer. (3) When the connection with the server has finished normally, the "EMS" LED changes from flashing to solid on. Displayed error code on the 7-SEG LED will disappear. (2) Press the "SET" button (2sec~) "EMS" LED = flashing "EMS" LED = on 7-SEG LED = "A" 7-SEG LED = "31" Error code A31 (4) When the connection to the server has finished, contact the utility power company again to report that the connection has finished. (5) This concludes all tasks. Attach the network adaptor cover. 12

13 6. Reference SEG LED error code When there is an error in the operation of the network adaptor, the error code is displayed in the 7-SEG LED as shown below. Handle the error by referring to the error code table. 7-SEG LED = "A" 7-SEG LED = "11" Error code : A11 13

14 Error code table Error code Category Sub-category Error cause A11 A12 Network FROM error RTC error Network adaptor failure Network adaptor failure A20 adaptor error Duplicate IP address Duplicate IP address A21 A22 A23 Communication error with the external server by the Utility Lithium-ion storage battery system (LJ-SK84A) error DNS error Connection timeout A24 HTTP error response A25 SSL authentication error A26 Received data error A error A31 Error response 404 error received from A32 the utility 406 error power company A33 server 500 error A error A40 A41 A42 A43 Receive timeout Communication error Register write error Protocol error LJ-SK84A replacement error Not connect to the Utility server Broadband router failure Server-side malfunction. Congested network. Server-side malfunction. Congested network. Server-side error Server-side error Expired SSL certificate Server-side error Server-side error The communication wires to the LJ-SK84A are not connected or have been disconnected Connection failure with the communication wires to the LJ-SK84A LJ-SK84A failure Connection failure with the communication wires to the LJ-SK84A LJ-SK84A failure Action Replace the network adaptor Replace the network adaptor Check if the IP address has been duplicated by another device on the local network. (***.***.***.230 cannot be used.) Re-check URL connection address once more. Inspect or replace the broadband router. Wait a while and check again. Check if there are any devices on the local network that are performing unusual communication. Wait a while and check again Check if there are any devices on the local network that are performing unusual communication. Wait a while and check again Check if there are any devices on the local network that are performing unusual communication. Wait a while and check again Wait a while and check again Update the firmware Wait a while and check again Server-side error Wait a while and check again Server unregistered Registered in the server Waiting for registration to the server LJ-SK84A replacement detected Wait a while and check again Check the communication wires to the LJ-SK84A Check the communication wires to the LJ-SK84A Inspect the LJ-SK84A Check the communication wires to the LJ-SK84A Inspect the LJ-SK84A Inform the utility power company of having replaced the LJ-SK84A A50 LJ-SK84A LJ-SK84A failure detected Inspect the LJ-SK84A failure When inspecting the Lithium-ion storage battery system, refer to the Lithium-ion storage battery system manual. When a Lithium-ion storage battery system unit has been replaced, you must perform 5. Network adaptor registration" again. 14 * *

15 6-2 Reset work Network adaptor to restart with the following procedure. (1) Press and hold the RESET button for 2 seconds or longer to restart the network adaptor. (2) When the 7-SEG LED displays 88 and the network adaptor has restarted. (1) Press the "RESET" button (2sec~) (2) 7-SEG LED = "88" (3) If the EMS LED is off, it is in the state waiting for the connection to the EMS Server. In order to make a connection to the server, and press the SET Button for more than 2 seconds. EMS Server not connect EMS Server connect 6-3 Factory Reset work If you want to return the Network adaptor to the initial state, it can be done in Expert mode. (1) Press the Factory Reset button in the Network setting screen. (2) Next, please operate the web browser and network adaptor along the message of the screen. (3) After the network adaptor has restart, please do the setting of network adaptor again. 15

16 Panasonic Corporation Web Site : Printed in Japan P40A K1028-2