Business Network Solutions for Dynamic Computing Services Connection

Transcription

1 Remote Access Service (RAS).docx C1 - Public Business Network Solutions for Dynamic Computing Services Connection Commissioning Swisscom (Schweiz) AG PMK-SME-PDC-OP Miller Patrice Inbetriebnahme Service Connection BNS zu DCS /11

2 Contents 1 Preparation Commissioning Cloud Part DCS Portal BNS Part BNS Dashboard Cloud Bonus Part vcloud Director (additional example for to a VM) /11

3 1 Preparation The following data should be prepared before starting the onboarding process, in order to ensure everything runs smoothly. The CP-ID can only be found once the onboarding process has been started (see chapter 2.2). Connection Point Name (EON name) BNS customer Network Address (Network address for your EON) /24 Gateway IP Address (IP for the virtual gateway connected to the EON -> auto-gen rec*) IP Address Router 1 (auto-gen rec) IP Address Router 2 (auto-gen rec) Pool Start IP Address (IP pool for the EON -> auto-gen rec) Pool End IP Address (IP pool for the EON -> auto-gen rec) DNS Server 1/2 (optional -> swisscom rec) / DNS Domain (for VM's connected to the EON -> optional) "Shared" Yes to share the EON in all your Dynamic Data Centers Connection Point ID (CP-ID to be used in the BNS dashboard to connect the EON) 16 ATTENTION: The desired subnet may not be in use at any other customer location. The desired subnet must be in the private network range (RFC 1918). If this requirement is ignored, the packets will not be routed between BNS and DCS. The point cannot be adjusted after it has been created. *auto-gen rec = auto-generated recommendation from Swisscom 2/11

4 2 Commissioning The first step for ensuring a successful configuration must take place on the DCS side. Using the data from Chapter 1, a virtual EON (external organisational network) must be configured, which can be seen on the DCS and should be connected to the BNS router. 2.1 Cloud Part DCS Portal First of all, log in to the ENT extranet using your personal extranet login. (extranet.swisscom.ch / datacenter.swisscomcloud.com) Click on the eservice "Dynamic Computing" within the DCS portal. The 2-factor authentication is started. In the next step, you select the data center via the DCS portal, which is to be connected to BNS. Click the network symbol of the respective DDC. 3/11

5 Now add a "Connection Point" under "Swisscom Cloud Services Connectivity". Now fill in the fields "Connection Point Name" and "Network Address" on the screen that appears. If required, the automatically generated details can be adjusted (e.g. Pool IP Range / DNS / Shared). Now click on "Submit Order". In a few minutes, you will receive an confirming the successful creation of the EON. 4/11

6 After the order has been completed successfully, the CP-ID will be visible on the DCS portal under "Swisscom Cloud Services Connectivity" in the Connectivity area of the respective data center under "Info". The remaining configuration settings will now be entered via the BNS dashboard. 5/11

7 2.2 BNS Part BNS Dashboard Log in to the Swisscom Customer Center at " Under the menu "Smart Business Connect", click on "Business Internet Services" and select the respective router that is displaying BNS. Click Configure to start the BNS dashboard. 6/11

8 Under the menu point "Groups", open the menu "Logical s" and enter the DCS CP-ID. The CP ID can be found on the DCS portal as described in section 2.1. Continue with the configuration via the BNS dashboard. Tick the checkbox (if the customer has already been informed). Now click "Validate and order". Open the shopping cart and submit the order. The should be established within a short period of time (approx. 15 minutes). 7/11

9 2.3 Cloud Bonus Part vcloud Director (additional example for to a VM) In the next to last step, you will log on to the extranet again and switch to the DCS portal (see chapter 2.1). This time, however, you go one step further and open the vcloud Director by clicking the server icon of the respective data centre. From the startpage, switch to the vapp that has been prepared for this example, for which a VM has already been commissioned and which is to be connected to BNS (the server must be stopped to complete the configuration). Right-click the VM and then select "Properties". 8/11

10 In the "Hardware" menu under "Network adapter", select "Add network..." via the drop-down menu. 9/11

11 On the next screen, select "VDC organisation network" and then click "Continue". Now select the correct BNS network and select "Finish". 10/11

12 Now click "OK" to attach the network. The server can now be started and the configuration tested. 11/11