H3C WA2600 Series Enhanced WLAN Access Points Installation Manual

Transcription

1 H3C WA2600 Series Enhanced WLAN Access Points Installation Manual Hangzhou H3C Technologies Co., Ltd. Manual Version: 6PW

2 Copyright , Hangzhou H3C Technologies Co., Ltd. and its licensors H3C Technologies Co., Ltd., a subsidiary of 3Com Corporation. All Rights Reserved No part of this manual may be reproduced or transmitted in any form or by any means without prior written consent of Hangzhou H3C Technologies Co., Ltd. Trademarks Notice H3C,, Aolynk,, H 3 Care,, TOP G,, IRF, NetPilot, Neocean, NeoVTL, SecPro, SecPoint, SecEngine, SecPath, Comware, Secware, Storware, NQA, VVG, V 2 G, V n G, PSPT, XGbus, N-Bus, TiGem, InnoVision and HUASAN are trademarks of Hangzhou H3C Technologies Co., Ltd. All other trademarks that may be mentioned in this manual are the property of their respective owners. The information in this document is subject to change without notice. Every effort has been made in the preparation of this document to ensure accuracy of the contents, but all statements, information, and recommendations in this document do not constitute the warranty of any kind, express or implied.

3 About This Manual Organization H3C WA2600 Series Enhanced WLAN Access Points Installation Manual is organized as follows: Chapter 1 Product Overview 2 Preparing for Installation 3 Installing the AP Contents Introduces the hardware configurations, appearance, and interfaces of the H3C WA2600 Series Enhanced WLAN Access Points. Specifies the environmental requirements for installing the H3C WA2600 Series Enhanced WLAN Access Points, presents installation precautions, and introduces the installation tools needed. Introduces how to install the H3C WA2600 Enhanced Series WLAN Access Points and how to connect the power supply units and the Ethernet cable. Conventions The manual uses the following conventions: Symbols Convention Description Means reader be extremely careful. Improper operation may cause bodily injury. Means reader be careful. Improper operation may cause data loss or damage to equipment. Means a complementary description.

4 Related Documentation In addition to this manual, each H3C WA2600 Series Enhanced WLAN Access Points(Fat) documentation set includes the following: Manual H3C WA Series WLAN Access Points User Manual H3C WA Series WLAN Access Points Web-Based Configuration Manual Description Provides a guide to the upgrade and operation of H3C WA series WLAN access points. It covers configurations of interface, VLAN, IP services, IP routing, multicast, security, system, QoS, wireless, and a command index. Introduces the Web-based management function of the WA Series WLAN Access Points. In addition to this manual, each H3C WA2600 Series Enhanced WLAN Access Points(Fit) documentation set includes the following: Manual H3C WX Series Access Controllers User Manual H3C WX Series Access Controllers Web-Based Configuration Manual Description Provides a guide to the operation of H3C series access controller products (including access controllers, access controller modules, and the access controller engine of unified switches). It covers configurations of CLI, VLAN, system maintenance and debugging, WLAN, IPv4, IPv6, port basic configurations, multicast protocols, 802.1x, AAA, SSH, ACL, QoS, description of the acronyms used throughout the manual, and a command index. Introduces the Web-based management function of the WX series access controllers.

5 Obtaining Documentation and Technical Support To obtain up-to-date documentation and technical support, go to and select your country or region. Depending on your selection, you will be redirected to either of the following websites: At Documentation Go to the following columns for different categories of product documentation: [Products & Solutions]: Provides information about products and technologies, as well as solutions. [Technical Support & Document > Technical Documents]: Provides several categories of product documentation, such as installation and configuration. [Technical Support & Document > Software Download]: Provides the documentation released with the software version. Technical Support At Documentation 1) Select Drivers & Downloads in the Support area. 2) Select Documentation for Type of File and select Product Category. Technical Support Register Your Product Warranty and other service benefits start from the date of purchase, so it is important to register your product quickly to ensure you get full use of the warranty and other service benefits available to you. Warranty and other service benefits are enabled through product registration. Register your product at go to Support, Product Registration. Support services are based

6 on accounts that you create or have authorization to access. First time users must apply for a user name and password that provides access to a number of esupport features including Product Registration, Repair Services, and Service Request. If you have trouble registering your product, please contact 3Com Global Services for assistance. Purchase Value-Added Services To enhance response times or extend warranty benefits, contact 3Com or your authorized reseller. Value-added services like Express SM and Guardian SM can include 24x7 telephone technical support, software upgrades, onsite assistance or advance hardware replacement. Experienced engineers are available to manage your installation with minimal disruption to your network. Expert assessment and implementation services are offered to fill resource gaps and ensure the success of your networking projects. More information on 3Com maintenance and Professional Services is available at Contact your authorized reseller or 3Com for a complete list of the value-added services available in your area. Troubleshoot Online You will find support tools posted on the web site at under Support, Knowledgebase. The Knowledgebase helps you troubleshoot H3C products. This query-based interactive tool contains thousands of technical solutions. Access Software Downloads Software Updates are the bug fix / maintenance releases for the version of software initially purchased with the product. In order to access these Software Updates you must first register your product on the web site at go to Support, Product Registration. First time users will need to apply for a user name and password. A link to software downloads can be found at under Support, Drivers and downloads. Software Upgrades are the software releases that follow the software version included with your original product. In order to access upgrades and related documentation you must first purchase a service contract from 3Com or your reseller.

7 Telephone Technical Support and Repair To enable telephone support and other service benefits, you must first register your product at Warranty and other service benefits start from the date of purchase, so it is important to register your product quickly to ensure you get full use of the warranty and other service benefits available to you. When you contact 3Com for assistance, please have the following information ready: Product model name, part number, and serial number Proof of purchase, if you have not pre-registered your product A list of system hardware and software, including revision level Diagnostic error messages Details about recent configuration changes, if applicable To send a product directly to 3Com for repair, you must first obtain a return authorization number (RMA). Products sent to 3Com, without authorization numbers clearly marked on the outside of the package, will be returned to the sender unopened, at the sender s expense. If your product is registered and under warranty, you can obtain an RMA number online at under support, Repair & Replacement Request. First time users will need to apply for a user name and password. Contact Us 3Com offers telephone, and internet access to technical support and repair services. To access these services for your region, use the appropriate telephone number, URL or address. Find a current directory of contact information posted on the web site at under Support, Technical Support Contact. Documentation Feedback You can your comments about product documentation to info@h3c.com. We appreciate your comments.

8 Environmental Protection This product has been designed to comply with the requirements on environmental protection. For the proper storage, use and disposal of this product, national laws and regulations must be observed.

9 Table of Contents 1 Product Overview Introduction Hardware Configuration LEDs Interfaces Preparing for Installation Safety Precautions Unpacking and Inspection Preparing Installation Tools Examining the Installation Site Temperature and Humidity Requirements Power Supply Grounding and Lightning Protection Installing the AP Installation Flowchart Determining the Installation Position Installing the AP on a Wall Installing the Wall-Mounting Bracket on the Wall Installing the AP on the Wall-Mounting Bracket Locking the AP onto the Wall-Mounting Bracket (Optional) Connecting the Power Supply Local Power Supply Power over Ethernet Connecting the AP to the Network i

10 1 Product Overview Introduction The H3C WA2600 Series Enhanced WLAN Access Points (hereinafter referred to as the WA2600 enhanced series) are one of the n access point (AP) product series developed by Hangzhou H3C Technologies Co., Ltd. (hereinafter referred to as H3C). The WA2600 enhanced series can serve as FIT APs to cooperate with wireless local area network (WLAN) switches or access controllers to provide wireless access for WLAN users. Figure 1-1 shows a typical scenario of hotspot deployments using the WA2600 enhanced series. Figure 1-1 Typical networking using the WA2600 enhanced series Figure 1-2 shows the appearance of the WA2600 enhanced series. 1-1

11 Figure 1-2 Appearance of the WA2600 enhanced series WA2610E-AGN WA2620E-AGN Table 1-1 Physical dimensions and weight of the WA2600 enhanced series Model WA2610E-AGN WA2620E-AGN Physical dimensions (H W D) mm ( in.) mm ( in.) Weight 1.2 kg (2.65 lb.) 1.3 kg (2.87 lb.) Hardware Configuration The two models of the WA2600 enhanced series have different radio frequencies (RFs) and structures. Table 1-2 lists the supported protocols and the chassis material. 1-2

12 Table 1-2 Supported protocols and chassis material Model WA2610E-AGN WA2620E-AGN Protocols and chassis material IEEE a/b/g/n, single-rf, sheet metal IEEE a/b/g/n, dual-rf, sheet metal The following describes the hardware configurations and functions of the WA2600 enhanced series in detail. LEDs The positions and identifications of LEDs on the panel vary with the models. For details about these LEDs, see Table 1-3. H3C WA2610E-AGN Figure 1-3 LEDs on the WA2610E-AGN H3C WA2620E-AGN Figure 1-4 LEDs on the WA2620E-AGN 1-3

13 Table 1-3 Description of the LEDs on the WA2610E-AGN and WA2620E-AGN LED Color QTY Meaning POWER Green 1 RADIO Green 1 2.4GHz (Wireless link LED) 5GHz (Wireless link LED) Green 1 Green 1 Displays the power supply status: On: The power supply is normal. Off/blinking: The power supply is not well connected or works abnormally. Displays the wireless link status: On: The wireless link is normal. Off: The wireless link is not initialized or the link is faulty. Blinking slowly: The wireless link works normally. Blinking rapidly: Data is being transmitted or received. Displays the 2.4 GHz wireless link status: On: The wireless link is normal. Off: The wireless link is not initialized or the link is faulty. Blinking slowly: The wireless link works normally. Blinking rapidly: Data is being transmitted or received. Displays the 5 GHz wireless link status: On: The wireless link is normal. Off: The wireless link is not initialized or the link is faulty. Blinking slowly: The wireless link works normally. Blinking rapidly: Data is being transmitted or received. 1-4

14 LED Color QTY Meaning 10/100M (Ethernet interface LED) 1000M (Ethernet interface LED) Yellow 1 Green 1 Displays the status of the Ethernet interface: On: The Ethernet interface is in the link-up state. Off: The Ethernet interface is in the link-down state. Blinking: Data is being transmitted or received at 10/100 Mbps. Displays the status of the 1000 M Ethernet interface: On: The Ethernet interface is in the link-up state. Off: The Ethernet interface is in the link-down state. Blinking: Data is being transmitted or received at 1000 Mbps. Interfaces The WA2600 enhanced series provide the following interfaces: 2.4 GHz or 5 GHz antenna interfaces A console interface An Ethernet copper interface A power supply interface In addition, the WA2600 enhanced series have a reset button and a security slot. 1-5

15 Interfaces provided by the H3C WA2610E-AGN Figure 1-5 Interfaces on the WA2610E-AGN Interfaces provided by the H3C WA2620E-AGN Figure 1-6 Interfaces on the WA2620E-AGN Top view Bottom view Table 1-4 describes the interfaces provided by each model. 1-6

16 Table 1-4 Descriptions of interfaces on the WA2600 enhanced series WLAN access points Model Interface Standards and protocols Description ANT-1 ANT-2 ANT-3 IEEE802.11a IEEE802.11b IEEE802.11g IEEE802.11n The antenna interfaces are provided for 2.4 GHz/5 GHz dual-rf antennas for MIMO transmission. WA2610E -AGN Console Ethernet RS/EIA-232 IEEE802.3 IEEE802.3u IEEE802.3af The console interface is used for device configuration and management. The Ethernet interface can serve as an uplink interface to access the Internet or MAN, and as a PoE interface at the same time. Power supply The power supply interface is used for +48 VDC power supply to the device. 1-7

17 Model Interface Standards and protocols Description Antenna interface (2.4 G) IEEE802.11b IEEE802.11g IEEE802.11n This antenna interface is used to connect a 2.4 GHz antenna or a feeder. Antenna interface (5 G) IEEE802.11a IEEE802.11n This antenna interface is used to connect a 5 GHz antenna or a feeder. WA2620E -AGN Console Ethernet RS/EIA-232 IEEE802.3 IEEE802.3u The console interface is used for device configuration and management. The Ethernet interface can serve as an uplink interface to access the Internet or MAN, and a PoE interface at the same time, supporting non-standard PoE power supply(the PoE input power is at least up to 16W). Power supply The power supply interface is used for +48 VDC power supply to the device. 1-8

18 2 Preparing for Installation This chapter describes the preparations for WA2600 installation, including the preparation of installation tools, environment examination, unpacking and inspection. Safety Precautions Installation and removal of the unit and its accessories must be carried out by qualified personnel. You must read all of the Safety Instructions supplied with your device before installation and operation. Installation und Ausbau der Anlage und ihrer Zubehörteile müssen von qualifiziertem Personal realisiert werden. Sie müssen vor der Installation oder Bedienung allen beiliegenden Sicherheitshinweise lesen. 2-1

19 负责安装和日常维护本设备的人员必须具备安全操作基本技能 在操作本设备前, 请务必认真阅读和执行产品手册规定的安全规范 Unpacking and Inspection Before unpacking the package, make sure that the package is intact, without any serious damage or signs of water soaking. When unpacking the package, avoid excessive force or collision. Otherwise, the articles inside the package may get damaged. The accessories may vary with the models. For the exact contents of the package, refer to the packing list. If the contents do not check with the packing list, timely contact your local dealer. If the package is found to be rusted or water soaked, stop unpacking and contact your local dealer immediately. Three omni antennas are shipped with the WA2610E-AGN, while six omni antennas are shipped with the WA2620E-AGN. 2-2

20 Preparing Installation Tools When installing the AP, you may need the tools listed in Table 2-1. Choose the appropriate tools according to the installation environment. Table 2-1 List of installation tools Type of tool General tools Special tools Auxiliary tools Indoor installation 1-meter-long rulers, marking pens, knives, and a percussion drill with appropriate bits Cable strippers, crimping pliers, and RJ-45 crimping pliers Ladders and rubber hammers Table 2-1 is for reference only. If you install the AP on a tabletop, none of the above tools is required. Examining the Installation Site Before installation, examine the installation site to make sure that the AP will work in a good environment. You can examine the installation site from the following two aspects. Temperature and Humidity Requirements Table 2-2 lists the operating temperature and humidity requirements. 2-3

21 Table 2-2 Environment specifications Specification Operating temperature (indoor) Storage temperature Operating humidity (noncondensing) Range -10 C to 65 C (14 F to 149 F) 40 C to +70 C ( 40 F to +158 F) 5% to 95% Power Supply The WA2600 series can be powered through 802.3af-compliant power over Ethernet (PoE) or an external power adaptor. For details see the Table 2-3. Outside China it is recommended that this unit be PoE powered. Please see the H3C/3Com product catalogues for a range of 802.3af compatible power sources. Table 2-3 Power Supply Power Source AC/DC Power Adapter Connection Details H3C WA2600 series access points can accept power from an AC/DC power adapter. Input specification is as follows: +48V, 0.52A min. Connect the adapter s power jack to the AP power interface. Ordering information If you need an AC/DC power adapter for your H3C WA2600 series access point, you must use the FSP025-1AD207A adapter(part number 0231A0EQ) which is available from H3C/3Com. 2-4

22 Power Source Power over Ethernet (PoE, IEEE 802.3af standard) power source Connection Details H3C WA2600 series access points can accept power from a PoE power source. No DC power adapter is required. Connect the PoE cable directly to the 10/100/1000 Base-TX Ethernet connector. Ordering information Please see the H3C/3Com product catalogues for a range of 802.3af compatible power sources. Grounding and Lightning Protection Table 2-4 Grounding and lightning protection requirements Item Grounding resistance Requirements The grounding resistance is typically required to be less than 5 ohms, and less than 10 ohms in an area that has less than 20 thunderstorm days a year. If an angle iron is to be buried into the earth as the earthing conductor, the grounding resistance is required to be less than 10 ohms. If the installation site has a high earth resistance rate, it is recommended to spray some salt water or resistance-reducing agent on the earth around the buried earthing conductor to reduce the resistance rate of the earth. The top of the earthing conductor should be at least 0.7 m (2.30 ft) away from the ground surface. In cold areas, the earthing conductor should be buried below the frozen soil layer. 2-5

23 Item Protection grounding Grounding lead AC power grounding Requirements If a grounding strip is available at the site, attach the yellow-green PGND cable of the AP to the grounding strip. The PGND cable must have a cross-section area of at least 6 mm 2 (0.01 in 2 ) and a length not longer than 3 m (9.84 ft). If no grounding strip is available at the site, hammer a 0.5 m (1.64 ft) or longer angle iron or steel tube into the earth. The angle iron should be sized at least mm ( in.); the steel tube should have a wall thickness of at least than 3.5 mm (0.18 in.) and be zinc-plated. Weld the yellow-green grounding cable to the angel iron or steel tube and treat the joint for corrosion protection. With a cross-section area of at least 6 mm 2 (0.01 in 2 ), the grounding cable should be as short as possible. Do not coil the cable. Make sure the lightning arresters of all devices and the peering devices connected to these devices are well grounded. The grounding lead is a metal conductor connecting the grounding strip to the grounding grid. The PGND cable of the device should be attached to the grounding strip. The grounding lead should not be longer than 30 m (98.43 ft). A zinc-plated flat steel with a cross-section area of 40 4 mm ( in) or 50 5 mm ( in) is recommended. The grounding strip and the grounding lead should be jointed using a 35 mm2 yellow-green PGND cable or directly welded together with the joint treated for corrosion protection. Make sure you use the power cable with a PE terminal but not the cables with only L and N wires. It is strictly prohibited to connect the N wire of the power cable to the protection ground of any other communications device, and the L and N wires must be connected correctly. 2-6

24 Item Lightning rod Feeder Outdoor lightning arresters Network cable Requirements In a plain area, the protection angel of the lightning rod should be less than 45 degrees. In a mountainous area or lightning intensified area, the protection angle should be less than 30 degrees. The lightning protection ground (for example, the ground of the lightning rod) and the protection ground of the equipment room should be connected to the same earthing conductor. The antenna support is ready and in accordance with the design requirement. A feeder lightning rod is already installed and grounded according to the design requirement. In case of outdoor installation, a power supply lightning arrester, a feeder lightning arrester and a network port lightning arrester are required. The power supply lightning arrester and feeder lightning arrester are located close to the AP while the network port lightning arrester is installed close to the peer device where the network cable goes out of the room. In case of outdoor installation, make sure to use a shielded network cable and the interconnected devices are well grounded. After you have completed the preparations, you can start installing the AP. For details, refer to 3 "Installing the AP" on page

25 3 Installing the AP The WA2600 enhanced series WLAN APs can be directly fixed onto a wall by using the wall-mounting brackets. The following introduces the wall-mounting procedure of the WA2600 enhanced series in detail. Installation Flowchart Figure 3-1 shows the installation flowchart of the WA2600 enhanced series. Figure 3-1 Installation flowchart Determining the Installation Position Determine the installation position by observing the following principles: 3-1

26 Leave as few obstacles (such as wall and ceiling) as possible between the AP and the wireless stations. Keep the AP far away from electronic devices (such as microwave ovens) that may generate RF noise. Install the AP in a place where it will not hinder people s daily work and life. Make sure the ceiling is strong enough and the structure is suitable in case of ceiling mounting. Reinforce the ceiling if needed. A padlock is required for ceiling mounting to prevent any falloff in case of shocks. Installing the AP on a Wall The following describes how to install a WA2600 enhanced series AP on a wall: Installing the Wall-Mounting Bracket on the Wall Installing the AP on the Wall-Mounting Bracket Locking the AP onto the Wall-Mounting Bracket (Optional) Installing the Wall-Mounting Bracket on the Wall 1) Drill holes 6 mm (0.24 in) in diameter on the wall where the AP is to be mounted. The drilled holes must correspond to those in the wall-mounting bracket. There are eight installation holes in total in the wall-mounting bracket. Select at least four of them for the installation. 3-2

27 Figure 3-2 Screw hole locations and screw hole size ) Insert the pointed end of anchors into the drilled holes and tap the flat end of anchors with a rubber hammer until they are all flush with the wall surface. 3) Align the holes in the wall-mounting bracket with the anchors and insert screws through the installation holes into the anchors, as shown in Figure ) Adjust the position of the wall-mounting bracket and tighten the screws. 3-3

28 Figure 3-3 Install the wall-mounting bracket Install the wall-mounting bracket with the arrow on the bracket pointing upwards. 3-4

29 Installing the AP on the Wall-Mounting Bracket The installation procedure is the same for both the WA2610E-AGN and WA2620E-AGN. The WA2610E-AGN is taken as an example in this manual. 1) Align the AP with the hooks on the wall-mounting bracket and hang the AP on the bracket. See (1) in Figure ) Press the AP downward to fix it. See (2) in Figure

30 Figure 3-4 Fix the AP onto the wall-mounting bracket Locking the AP onto the Wall-Mounting Bracket (Optional) The WA2600 enhanced series APs have a security slot on the top, which can be used to lock the AP onto the wall-mounting bracket to prevent theft. Follow these steps to lock the AP onto the wall-mounting bracket: 1) Insert the locking plate into the security slot on the top of the AP. See (1) in Figure ) Turn the locking plate counterclockwise until the hole on the locking plate is aligned with the hole in the wall-mounting bracket. See (2) in Figure ) Put the latch through the two holes that are aligned in step 2. See (3) in Figure

31 4) Lock the latch with a lock. Figure 3-5 Lock the AP onto the wall-mounting bracket The lock is user supplied. 3-7

32 Connecting the Power Supply Local Power Supply Connect the AP to the power source through the power adapter, as shown in Figure 3-6. Figure 3-6 Local power supply connection Power over Ethernet If the uplink device of the AP is a PoE-capable switch or the like, use an Ethernet cable to connect the Ethernet interface of the AP to the PoE-capable device. Figure 3-7 PoE connection 3-8

33 In the PoE mode, you do not need to connect the power interface to a power source. You only need to connect one end of an Ethernet cable to the Ethernet interface of the AP and the other end to an Ethernet interface of the PoE-capable device (for example, an Ethernet switch). Identify the silkscreen on the device to avoid taking the console interface for the Ethernet interface, or vice versa. The WA2620E-AGN supports only non-standard PoE power supply(the PoE input power is at least up to 16W). Connecting the AP to the Network The WA2600 enhanced series can access the Internet or MAN through the Ethernet uplink interface. Connect the Ethernet interface of the AP to an Ethernet interface of an Ethernet switch to implement Internet or MAN access, as shown in Figure 3-8. Figure 3-8 Connect the AP to the network 3-9