Lab Configuring the Management VLAN on a Single Switch
|
|
|
- Joseph Davidson
- 6 years ago
- Views:
Transcription
1 Lab Configuring the Management VLAN on a Single Switch Objective Equipment Scenario Step 1 In this lab, students will configure and use a non-default Management VLAN. This lab will use the config-vlan and vlan database modes to configure VLANs. The following equipment is required to complete this lab: Catalyst 3550 or 2950 series switch IOS 12.1(11)EA1 Two network-capable workstations with Telnet client packages Corporate headquarters has decided to further improve network management security by implementing VLANs to separate user and management traffic. Build the network according to the diagram. Reset the switch to factory defaults. Assign IP addresses to the workstations. Configure the switch name, but do not configure VLANs and do not assign an IP address to the switch. 1-7 CCNP 3: Multilayer Switching v Lab Copyright 2005, Cisco Systems, Inc.
2 Step 2 From privileged mode, enter VLAN database mode: ALSwitch#vlan database ALSwitch(vlan)# Create VLAN 10 and name it Users. ALSwitch(vlan)#vlan 10 name Users VLAN 10 added: Name: Users ALSwitch(vlan)# Verify that the VLAN has been created. ALSwitch(vlan)#show VLAN ISL Id: 1 Name: default Media Type: Ethernet VLAN Id: VLAN ISL Id: 10 Name: Users Media Type: Ethernet VLAN Id: VLAN ISL Id: 1002 Name: fddi-default Media Type: FDDI VLAN Id: VLAN ISL Id: 1003 Name: token-ring-default Media Type: Token Ring VLAN Id: Maximum ARE Hop Count: 7 Maximum STE Hop Count: 7 VLAN ISL Id: 1004 Name: fddinet-default Media Type: FDDI Net VLAN Id: CCNP 3: Multilayer Switching v Lab Copyright 2005, Cisco Systems, Inc.
3 STP Type: IEEE VLAN ISL Id: 1005 Name: trnet-default Media Type: Token Ring Net VLAN Id: STP Type: IBM 1. What VLAN numbers and names are displayed? Step 3 Exit VLAN database mode. ALSwitch(vlan)#exit APPLY completed. Exiting... ALSwitch# Display summary VLAN information from privileged mode default active Fa0/1, Fa0/2, Fa0/3, Fa0/4 Fa0/5, Fa0/6, Fa0/7, Fa0/8 Fa0/9, Fa0/10, Fa0/11, Fa0/12 Gi0/1, Gi0/2 10 Users active CCNP 3: Multilayer Switching v Lab Copyright 2005, Cisco Systems, Inc.
4 Step 4 Enter global configuration mode. Use the config-vlan configuration mode to create VLAN 99 and name it Mgt. ALSwitch(config)#vlan 99 ALSwitch(config-vlan)#name Mgt Return to privileged mode and verify the VLAN configuration. ALSwitch(config-vlan)#end 00:44:11: %SYS-5-CONFIG_I: Configured from console by console default active Fa0/1, Fa0/2, Fa0/3, Fa0/4 Fa0/5, Fa0/6, Fa0/7, Fa0/8 Fa0/9, Fa0/10, Fa0/11, Fa0/12 Gi0/1, Gi0/2 10 Users active 99 Mgt active 99 enet Can a Telnet connection from either PC to the switch be established? Explain why or why not. 4-7 CCNP 3: Multilayer Switching v Lab Copyright 2005, Cisco Systems, Inc.
5 Step 5 Enter global configuration mode. Assign an IP address to VLAN 99 on the switch. ALSwitch(config)#interface vlan 99 ALSwitch(config-if)#ip address ALSwitch(config-if)#no shutdown 3. Can a Telnet connection from either workstation to the switch be established? Explain why or why not. Step 6 Make port FastEthernet0/1 a member of VLAN 10. ALSwitch(config)#interface fastethernet 0/1 ALSwitch(config-if)#switchport mode access ALSwitch(config-if)#switchport access vlan 10 Make port FastEthernet0/4 a member of VLAN 99. ALSwitch(config)#interface fastethernet0/4 ALSwitch(config-if)#switchport mode access ALSwitch(config-if)#switchport access vlan 99 ALSwitch(config-if)#end Return to privileged mode and verify the VLAN configuration default active Fa0/2, Fa0/3, Fa0/5, Fa0/6 Fa0/7, Fa0/8, Fa0/9, Fa0/10 Fa0/11, Fa0/12, Gi0/1, Gi0/2 10 Users active Fa0/1 99 Mgt active Fa0/4 99 enet CCNP 3: Multilayer Switching v Lab Copyright 2005, Cisco Systems, Inc.
6 Note VLANs 10 and 99 now have associated interfaces. 4. Now is it possible to establish a Telnet connection from either workstation to the switch? Explain why or why not. Return to privileged mode and verify the VLAN configuration. ALSwitch(config-if)#end ALSwitch# 00:54:52: %SYS-5-CONFIG_I: Configured from console by console default active Fa0/2, Fa0/3, Fa0/5, Fa0/6 Fa0/7, Fa0/8, Fa0/9, Fa0/10 Fa0/11, Fa0/12, Gi0/1, Gi0/2 10 Users active Fa0/1 99 Mgt active Fa0/4 99 enet CCNP 3: Multilayer Switching v Lab Copyright 2005, Cisco Systems, Inc.
7 Note VLANs 10 and 99 now have associated interfaces. Step 7 Try to open a Telnet session to the switch from workstation Did it work? Why or why not? Try to open a Telnet session to the switch from workstation Did it work? Why or why not? Configure the vty lines for Telnet access into the switch. ALSwitch(config)#line vty 0 15 ALSwitch(config-line)#password cisco ALSwitch(config-line)#login ALSwitch(config-line)#end A Telnet session from workstation 2 should now be successful. 7-7 CCNP 3: Multilayer Switching v Lab Copyright 2005, Cisco Systems, Inc.
PT Activity 4.4.1: Basic VTP Configuration
Topology Diagram Addressing Table Device Interface IP Address Subnet Mask Default Gateway S1 VLAN 99 172.17.99.11 255.255.255.0 N/A S2 VLAN 99 172.17.99.12 255.255.255.0 N/A S3 VLAN 99 172.17.99.13 255.255.255.0
Lab Configuring Fast EtherChannel
Lab 3.7.5 Configuring Fast EtherChannel Objective Scenario The purpose of this lab is to provide more bandwidth between Ethernet switches. Two 100-Mb links will be combined together to form a full duplex
Lab Routing Between an External Router and an Internal Route Processor
Lab 5.3.4.2 Routing Between an External Router and an Internal Route Processor Objective Scenario The purpose of this lab is to configure routing between an internal route processor and an external router.
Lab Inter-VLAN Routing with the Internal Route Processor
Lab 5.3.4.1 Inter-VLAN Routing with the Internal Route Processor Objective Scenario The purpose of this lab is to configure Inter-VLAN routing using a switch with an internal route processor. The network
Lab Catalyst 2950T and 3550 Series VTP Domain and VLAN Trunking
Lab 2.3.7.1 Catalyst 2950T and 3550 Series VTP Domain and VLAN Trunking Objective Configure a VLAN trunk between two Cisco Catalyst WS-C2950T-24-EI switches and a Cisco Catalyst WS-C3550-24-EMI switch
Lab Catalyst 2950T and 3550 Series VTP Domain and VLAN Trunking
Lab 2.9.2 Catalyst 2950T and 3550 Series VTP Domain and VLAN Trunking Objective Configure a VLAN trunk between two Cisco Catalyst WS-C2950T-24-EI switches and a Cisco Catalyst WS-C3550-24-EMI switch in
Lab Catalyst 2950T and 3550 Series Static VLANS
Lab 2.9.1 Catalyst 2950T and 3550 Series Static VLANS Objective Create and maintain VLANs on a Cisco Catalyst 2950T or 3550 series Ethernet switch using the command-line interface (CLI) mode. Scenario
Device Interface IP Address Subnet Mask Default Gateway. Ports Assignment Network
Felix Rohrer Topology Diagram Addressing Table Device Interface IP Address Subnet Mask Default Gateway S1 VLAN 99 172.17.99.11 255.255.255.0 N/A S2 VLAN 99 172.17.99.12 255.255.255.0 N/A S3 VLAN 99 172.17.99.13
Lab 6.4.1: Basic Inter-VLAN Routing
Topology Diagram Addressing Table Device (Hostname) Interface IP Address Subnet Mask Default Gateway S1 VLAN 99 172.17.99.11 255.255.255.0 172.17.99.1 S2 VLAN 99 172.17.99.12 255.255.255.0 172.17.99.1
Lab Catalyst 2950 and 3550 Series Intra-VLAN Security
Lab 7.2.5.1 Catalyst 2950 and 3550 Series Intra-VLAN Security Objective Scenario Configure intra-vlan security with Access Control Lists (ACLs) using the command-line interface (CLI) mode. This lab will
Lab 9.1.5a Trunking with ISL 2924XL Series
Lab 9.1.5a Trunking with ISL 2924XL Series Objective Create a basic switch configuration and verify it. Create multiple VLANs, name them and assign multiple member ports to them. Create an ISL trunk line
Lab 5: Inter-VLANs Routing
Lab 5: Inter-VLANs Routing Network Topology:- Device Interface IP Address Subnet Mask Gateway/Clock Rate Fa 0/0.10 10.5.0.1 255.255.255.192 ----- R1 Fa 0/0.20 10.6.0.1 255.255.255.192 ----- Fa 0/0.30 10.10.0.1
Lab Catalyst 2950T and 3550 Series Basic Setup
Lab 1.2.9.1 Catalyst 2950T and 3550 Series Basic Setup Objective Configure a Cisco Catalyst 2950T or 3550 series Ethernet switch for the first time using the command-line interface (CLI) mode. Basic first
Basic switch configuration
Basic switch configuration Cisco IOS Basic switch functions, names and passwords The switch name is tool to let us see what device we are connected to. The prompt will display the name of the switch so
Netw 3000 VLAN 1 LAB Darlene Redmond Ryan Gamblin January 19 th 2012
Netw 3000 VLAN 1 LAB Darlene Redmond Ryan Gamblin January 19 th 2012 3. Attach a workstation to the Management VLAN and demonstrate a successful login to the switch at the privileged exec mode, with a
Lab 5.5.2: Challenge Spanning Tree Protocol
Topology Diagram Addressing Table Device (Hostname) Interface IP Address Subnet Mask Default Gateway S1 VLAN 99 172.17.99.11 255.255.255.0 N/A S2 VLAN 99 172.17.99.12 255.255.255.0 N/A S3 VLAN 99 172.17.99.13
Lab Port Level Tuning to Control STP Behavior
Lab 3.10.7 Port Level Tuning to Control STP Behavior Objective The purpose of this lab is to use PortFast, UplinkFast, BPDU guard, root guard, and UDLD to control STP behavior on a port. Scenario Note:
Question 5.1. Every port on a switch is a collision domain. Every port on a router is a collision domain.
Question 5.1 Q 5.1.1 Number of Collision Domains: = 14 Every port on a switch is a collision domain. Every port on a router is a collision domain. Number of Broadcast Domains: = 5 Every port on a router
Lab Add, Move, and Change MAC Addresses
Lab 6.2.6 Add, Move, and Change MAC Addresses Objective Create and verify a basic switch configuration. Move a PC from one switch port to another and add a new PC to the switch. Background/Preparation
Chapter 2 Lab 2-1, Static VLANS, VLAN Trunking, and VTP Domains and Modes
Chapter 2 Lab 2-1, Static VLANS, VLAN Trunking, and VTP Domains and Modes Topology Objectives Background Set up a VTP domain. Create and maintain VLANs. Configure ISL and 802.1Q trunking. VLANs logically
Lab Configuring Per-Interface Inter-VLAN Routing (Solution)
(Solution) Topology Addressing Table Objectives Device Interface IP Address Subnet Mask Default Gateway R1 G0/0 192.168.20.1 255.255.255.0 N/A G0/1 192.168.10.1 255.255.255.0 N/A S1 VLAN 10 192.168.10.11
Lab Configuring Per-Interface Inter-VLAN Routing (Instructor Version)
(Instructor Version) Instructor Note: Red font color or Gray highlights indicate text that appears in the instructor copy only. Topology Addressing Table Objectives Device Interface IP Address Subnet Mask
Lab Managing the MAC Address Table 2900XL Series
Lab 6.2.3 Managing the MAC Address Table 2900XL Series Objective Create a basic switch configuration. Manage the switch MAC table. Background/Preparation Cable a network similar to the one in the diagram.
IEEE 802.1Q Configuration
CHAPTER15 This chapter describes: IP Routing over IEEE 802.1Q InterVLAN Routing and 802.1Q Trunking IP Routing over IEEE 802.1Q This section provides procedures for configuring protocols supported with
PT Activity 2.5.1: Basic Switch Configuration
Topology NOTE TO USER: This activity is a variation of Lab 2.5.1. Packet Tracer may not support all the tasks specified in the hands-on lab. This activity should not be considered equivalent to completing
Lab Analyzing a Test Plan and Performing a Test
Lab 7.1.6 Analyzing a Test Plan and Performing a Test Objectives Analyze a sample test plan to determine: The subject of the test The methods and tools for testing The potential results Perform the test
Configuring a LAN with DHCP and VLANs
CHAPTER 15 The Cisco 860 and Cisco 880 series Integrated Services Routers (ISRs) support clients on both physical LANs and VLANs. The routers can use the Dynamic Host Configuration Protocol (DHCP) to enable
Note: Use two 2960 switches for ALS1 and ALS2 and two 3560 switches for DLS1 and DLS2
LAB 2 - Part I - VLANs, VLAN Trunking, and VTP Domains Topology: Objectives Set up a VTP domain. Create and maintain VLANs. Configure 802.1Q trunking. Background VLANs logically segment a network by function,
EtherSwitch Service Module (ES) Configuration Example
EtherSwitch Service Module (ES) Configuration Example Document ID: 82288 Contents Introduction Prerequisites Requirements Components Used Related Products Conventions EtherSwitch Modules Concepts Configure
Lab - Configuring VLANs and Trunking (Solution)
(Solution) Topology Addressing Table Objectives Device Interface IP Address Subnet Mask Default Gateway S1 VLAN 1 192.168.1.11 255.255.255.0 N/A S2 VLAN 1 192.168.1.12 255.255.255.0 N/A PC-A NIC 192.168.10.3
Lab - Troubleshooting VLAN Configurations (Instructor Version Optional Lab)
(Instructor Version Optional Lab) Instructor Note: Red font color or gray highlights indicate text that appears in the instructor copy only. Optional activities are designed to enhance understanding and/or
TELECOMMUNICATION MANAGEMENT AND NETWORKS
QUAID-E-AWAM UNIVERSITY OF ENGINEERING SCIENCE AND TECHNOLOGY, NAWABSHAH TELECOMMUNICATION MANAGEMENT AND NETWORKS LAB # 3 CONFIGURING INTERFACES OF ROUTER AND SWITCH Topology Diagram Addressing Table
KIM DONNERBORG / RTS. Cisco Lab Øvelse Af Kim Donnerborg / RTS. Side 0 af 8
KIM DONNERBORG / RTS Side 0 af 8 INDHOLDSFORTEGNELSE Lab: Basic Router Configuration... 2 Topology Diagram... 2 Addressing Table... 2 Learning Objectives... 2 Scenario... 2 Task 1: Cable the Network....
Lab 5: Basic VLAN Configuration
Topology Diagram Addressing Table Device (Hostname) Interface IP Address Subnet Mask Default Gateway S1 VLAN 99 172.17.99.11 255.255.255.0 N/A S2 VLAN 99 172.17.99.12 255.255.255.0 N/A S3 VLAN 99 172.17.99.13
Lab 8-2 Securing Spanning Tree Protocol
Lab 8-2 Securing Spanning Tree Protocol Learning Objectives Secure the Layer 2 spanning tree topology with BPDU guard Protect the primary and secondary root bridge with root guard Protect switchports from
Table of Contents. isco Configuring 802.1q Trunking Between a Catalyst 3550 and Catalyst Switches Running Integrated Cisco IOS (Nativ
king Between a Catalyst 3550 and Catalyst Switches Running isco Configuring 802.1q Trunking Between a Catalyst 3550 and Catalyst Switches Running Integrated Cisco IOS (Nativ Table of Contents Configuring
configuring and connecting 24
Lecture (01) configuring and connecting 24 ports switch Dr. Ahmed M. ElShafee ١ ٢ Step 1: connecting your PC to the Console Port. Open HyperTerminal software Press RETURN to get started. Switch> (User
Lecture (01) configuring and connecting 24 ports switch
Lecture (01) configuring and connecting 24 ports switch Dr. Ahmed M. ElShafee ١ ٢ Step 1: connecting your PC to the Console Port. Open HyperTerminal software Press RETURN to get started. Switch> (User
VLANs. CCNA Exploration Semester 3 Chapter Sep-13
VLANs CCNA Exploration Semester 3 Chapter 3 1 Topics The role of VLANs in a network Trunking VLANs Configure VLANs on switches Troubleshoot common VLAN problems 2 Semester 3 LAN Design Basic Switch Concepts
RealCiscoLAB.com. Multiple Spanning Tree. Topology. Objective. Background. CCNPv6 SWITCH. Observe the behavior of multiple spanning tree (MST).
RealCiscoLAB.com CCNPv6 SWITCH Multiple Spanning Tree Topology Objective Background Observe the behavior of multiple spanning tree (MST). Four switches have just been installed. The distribution layer
This document is exclusive property of Cisco Systems, Inc. Permission is granted to print and copy this document for non-commercial distribution and
This document is exclusive property of Cisco Systems, Inc. Permission is granted to print and copy this document for non-commercial distribution and exclusive use by instructors in the CCNA Exploration:
This document is exclusive property of Cisco Systems, Inc. Permission is granted to print and copy this document for non-commercial distribution and
This document is exclusive property of Cisco Systems, Inc. Permission is granted to print and copy this document for non-commercial distribution and exclusive use by instructors in the CCNA Exploration:
Lab Verifying NAT and PAT Configuration
Lab 1.1.5 Verifying NAT and PAT Configuration Objective Configure a router for Network Address Translation (NAT) and Port Address Translation (PAT) Test the configuration and verify NAT/PAT statistics
Lab 6.2.7a Managing Switch Operating System Files 2900XL Series
Lab 6.2.7a Managing Switch Operating System Files 2900XL Series Objective Create and verify a basic switch configuration. Backup the switch IOS to a TFTP server and then restore it. Background/Preparation
Lab - Configuring VLANs and Trunking
Topology Addressing Table Objectives Device Interface IP Address Subnet Mask Default Gateway S1 VLAN 1 192.168.1.11 255.255.255.0 N/A S2 VLAN 1 192.168.1.12 255.255.255.0 N/A PC-A NIC 192.168.10.3 255.255.255.0
ISP /24. Fas0/0. Fas1/0/1. Fas1/0/22 NYCORE1. Cisco PS. Fas0/1. Lab Nic /24
Introduction The Configuring VLANs and Trunks module provides you with the instructions and Cisco hardware to develop your hands on skills in configuring layer 2 technologies VLANs and trunking. This module
CS IT ports switch basic configuration. Lecture (01) Introduction to 24 ports managed switches By: Dr. Ahmed ElShafee.
Lecture (01) Introduction to 24 ports managed switches By: Dr. Ahmed ElShafee CS IT Agenda 24 ports switch basic configuration Switch remote configuration peer2peer star network clients/server star network
Lab Configuring Basic Switch Settings (Solution)
(Solution) Topology Addressing Table Objectives Device Interface IP Address Subnet Mask Default Gateway S1 VLAN 99 192.168.1.2 255.255.255.0 192.168.1.1 PC-A NIC 192.168.1.10 255.255.255.0 192.168.1.1
Configuring ISL Trunking Between Catalyst Switches Running CatOS and Cisco IOS System Software
Configuring ISL Trunking Between Catalyst Switches Running CatOS and Cisco IOS System Software Document ID: 8759 Contents Introduction Prerequisites Requirements Components Used Background Theory Important
All Transparent VTP Domain to Server Client VTP Domain Migration Configuration Example
All Transparent VTP Domain to Server Client VTP Domain Migration Configuration Example Document ID: 81682 Contents Introduction Prerequisites Requirements Components Used Conventions Background Information
Lab 3-2 Modifying Default Spanning Tree Behavior
Lab 3-2 Modifying Default Spanning Tree Behavior Objective The purpose of this lab is to observe what happens when the default spanning tree behavior is modified. Scenario Four switches have just been
Lab - Configuring VLANs and Trunking
Topology Addressing Table Objectives Device Interface IP Address Subnet Mask Default Gateway S1 VLAN 1 192.168.1.11 255.255.255.0 N/A S2 VLAN 1 192.168.1.12 255.255.255.0 N/A PC-A NIC 192.168.10.3 255.255.255.0
Configuring a Management IP Address on Catalyst 4500/4000, 5500/5000, 6500/6000, and Catalyst Fixed Configuration Switches
Configuring a Management IP Address on Catalyst 4500/4000, 5500/5000, 6500/6000, and Catalyst Fixed Configuration Switches Document ID: 10594 Interactive: This document offers customized analysis of your
Route between VLANs using a 3560 switch with an internal route processor using Cisco Express Forwarding (CEF).
Lab 3- Part I Inter-VLAN routing with a Multilayer Switch Configuration and Management of Networks - 2014 Topology Objective Route between VLANs using a 3560 switch with an internal route processor using
Table of Contents. co Configuring InterVLAN Routing and ISL/802.1Q Trunking on a Catalyst 2900XL/3500XL/2950 Switch Using An Extern
outing and ISL/802.1Q Trunking on a Catalyst 2900XL/3500XL/2 co Configuring InterVLAN Routing and ISL/802.1Q Trunking on a Catalyst 2900XL/3500XL/2950 Switch Using An Extern Table of Contents Configuring
Lab Hot Standby Router Protocol
Lab 6.5.1 Hot Standby Router Protocol Objective Scenario Step 1 Step 2 Configure Hot Standby Router Protocol (HSRP) on a pair of routers to provide redundant router services to a network. Two routers are
Lab Configuring Inter-VLAN Routing
Lab 9.3.6 Configuring Inter-VLAN Routing Objective Create a basic switch configuration and verify it. Create multiple VLANs, name them and assign multiple member ports to them. Create a basic configuration
LAN Switching and Wireless
LAN Switching and Wireless CCNA Exploration Labs and Study Guide Allan Johnson ii LAN Switching and Wireless, CCNA Exploration Labs and Study Guide LAN Switching and Wireless CCNA Exploration Labs and
Lecture (04) VTP Ports Security
Lecture (04) VTP Ports Security By: Dr. Ahmed ElShafee ١ Dr. Ahmed ElShafee, ACU : Fall 2015, Practical App. Networks II VTP VLAN Trucking Protocol (VTP) is a Cisco proprietary protocol that propagates
Chapter 3 Lab 3-3, Per-VLAN Spanning Tree Behavior
Chapter 3 Lab 3-3, Per-VLAN Spanning Tree Behavior Topology Objectives Background Observe the behavior of a separate spanning tree instance per VLAN. Change spanning tree mode to rapid spanning tree. Four
Using VLAN & Bridge APPENDIX
APPENDIX I Using VLAN & Bridge The VLAN & Bridge application allows you to configure groups of ports independent of their physical location as a virtual LAN. This arrangement is called a logical grouping
Lab Configuring OSPF Timers 2500 Series
Lab 2.3.5 Configuring OSPF Timers 2500 Series Objective Setup an IP addressing scheme for OSPF area. Configure and verify OSPF routing. Modify OSPF interface timers to adjust efficiency of network. Background/Preparation
Internetwork Expert s CCNP Bootcamp. VLANs, Trunking, & VTP. VLANs Overview
Internetwork Expert s CCNP Bootcamp VLANs, Trunking, & VTP http:// VLANs Overview Virtual Local Area Network Hosts in the same VLAN share the same broadcast domain Switches create a separate CAM table
Lab 1.1.4a Configuring NAT
Lab 1.1.4a Configuring NAT Objective Configure a router to use network address translation (NAT) to convert internal IP addresses, typically private addresses, into outside public addresses. Background/Preparation
Antonio Cianfrani. Packet Tracer
Antonio Cianfrani Packet Tracer Packet Tracer (1/2) Packet Tracer? Cisco Packet Tracer is a software able to emulate CISCO networking devices. Packet Tracer features: Allows to create network topologies
Lab 1.1.4c Configuring Static NAT Addresses
Lab 1.1.4c Configuring Static NAT Addresses Objective Configure a router to use network address translation (NAT) to convert internal IP addresses, typically private addresses, into outside public addresses.
RealCiscoLAB.com. Observe the behavior of a separate spanning tree instance per VLAN. Change spanning tree mode to rapid spanning tree.
RealCiscoLAB.com CCNPv6 SWITCH Per-VLAN Spanning Tree Behavior Topology Objectives Background Observe the behavior of a separate spanning tree instance per VLAN. Change spanning tree mode to rapid spanning
CCNP SWITCH 6.0 Student Lab Manual
CCNP SWITCH 6.0 Student Lab Manual This document is exclusive property of Cisco Systems, Inc. Permission is granted to print and copy this document for non-commercial distribution and exclusive use by
Lab Password Recovery Procedure on a Catalyst 2900 Series Switches
Lab 6.2.8 Password Recovery Procedure on a Catalyst 2900 Series Switches Objective Create and verify a basic switch configuration verify it. Change passwords to the password recovery procedure be performed.
Lab Configuring Static VLANs
Lab 8.2.3 Configuring Static VLANs Objective Create a basic switch configuration and verify it. Determine the switch firmware version. Create two VLANs, name them and assign member ports to them. Background/Preparation
Lab Configuring 802.1Q Trunk-Based Inter-VLAN Routing (Instructor Version Optional Lab)
(Instructor Version Optional Lab) Instructor Note: Red font color or gray highlights indicate text that appears in the instructor copy only. Optional activities are designed to enhance understanding and/or
Lab Password Recovery Procedure on a Catalyst 2950 Series Switch 2900XL Series
Lab 6.2.8 Password Recovery Procedure on a Catalyst 2950 Series Switch 2900XL Series Objective Create and verify a basic switch configuration. Change passwords and use the password recovery procedure.
ICND1. Switch Configuration Lab. All configurations have been set to factory defaults for these labs
ICND1 Switch Configuration Lab TOPOLOGY 3xPC (hosts) 2x2950 (Layer 2 Switches) 1x3560 (Layer 3 Switch) 5x2811 (Routers, unused in this set of labs) All configurations have been set to factory defaults
Lab Configure Extended VLANs, VTP, and DTP
Topology Addressing Table Objectives Part 1: Configure VTP Part 2: Configure DTP Table Heading Interface IP Address Subnet Mask S1 VLAN 99 192.168.99.1 255.255.255.0 S2 VLAN 99 192.168.99.2 255.255.255.0
Lab Classifying Traffic using Class of Service at the Access Layer
Lab 8.9.1 Classifying Traffic using Class of Service at the Access Layer Objective For effective quality of service (QoS) it is important to classify traffic as soon as possible. This allows routing and
Chapter 4 Lab 4-1, Inter-VLAN Routing with an External Router
Chapter 4 Lab 4-1, Inter-VLAN Routing with an External Router Topology Objective Background Configure inter-vlan routing using an external router, also known as a router on a stick. Inter-VLAN routing
BASIC CONFIGURATION CISCO SWITCH
BASIC CONFIGURATION CISCO SWITCH switch#show running-config ( prikaz trenutne konfiguracije ) switch#show startup-config ( prikaz startne konfiguracije ) switch#configure terminal ( ulaz u global config
Lab Configuring Router Passwords. Objective. Background/Preparation. Step 1 Login to the router in user EXEC mode
Lab 3.1.3 Configuring Router Passwords Objective Configure a password for console login to user EXEC mode. Configure a password for virtual terminal (Telnet) sessions. Configure a secret password for privileged
This chapter describes how to configure VLANs on the Cisco 7600 series routers.
CHAPTER 14 This chapter describes how to configure VLANs on the Cisco 7600 series routers. For complete syntax and usage information for the commands used in this chapter, refer to the Cisco 7600 Series
Document Configurations for Standardization across the Camera. Network. Kevin O Neal. DeVry University. NETW206: Introduction to Switching
Document Configurations for Standardization across the Camera Network Kevin O Neal DeVry University NETW206: Introduction to Switching Submitted to: Professor: Hopkins Date: 8-5-2012 To standardize the
Lab Multigroup Hot Standby Router Protocol
Lab 6.2.2.2 Multigroup Hot Standby Router Protocol Objective Scenario Step 1 Configure Multigroup Hot Standby Router Protocol (MHSRP) on a pair of routers to provide redundant router services to a network.
Cisco Switch VLAN Setup (IOS)
Summary WirelessTrakker requires that the switch ports involved for connecting the components for WirelessTrakker be 802.1q VLAN tagged / trunked ports. These directions tell you how to do that. Note:
the larger the number of users and devices, the more broadcasts and packets each switch must handle.
VLANs Introduction By default, routers allow broadcasts to occur only within the originating network, while switches forward broadcasts to all segments. Flat network = one broadcast domain. that the largest
VLANs. Traditional Campus Networks. Performance Issues. Broadcast Issues. Bridges terminate collision domains
Traditional Campus Networks Broadcast Domain VLANs Collision Domain 1 Collision Domain 2 Bridges terminate collision domains 2003, Cisco Systems, Inc. All rights reserved. 2-1 2003, Cisco Systems, Inc.
Lab Hot Standby Router Protocol
Lab 6.2.2.1 Hot Standby Router Protocol Objective Scenario Configure Hot Standby Router Protocol (HSRP) on a pair of routers to provide redundant fault tolerant router services to a network. Two routers
King Fahd University of Petroleum & Minerals. Configuration of Routers and Establishing Routed Networks
King Fahd University of Petroleum & Minerals Electrical Engineering Department EE 400, Experiment # 7 Objectives: Configuration of Routers and Establishing Routed Networks The objective of this experiment
VLANs. 2003, Cisco Systems, Inc. All rights reserved. 2-1
VLANs 2003, Cisco Systems, Inc. All rights reserved. 2-1 Traditional Campus Networks Broadcast Domain Collision Domain 1 Collision Domain 2 Bridges terminate collision domains 2003, Cisco Systems, Inc.
RealCiscoLAB.com. Securing Spanning Tree Protocol. Topology. Objectives. Background. CCNPv6 SWITCH
RealCiscoLAB.com CCNPv6 SWITCH Securing Spanning Tree Protocol Topology Objectives Background Secure the Layer 2 spanning-tree topology with BPDU guard. Protect the primary and secondary root bridge with
Lab 9.1.5b Trunking with 802.1q
Lab 9.1.5b Trunking with 802.1q Objective Create a basic switch configuration and verify it. Create multiple VLANs, name them and assign multiple member ports to them. Create an 802.1q trunk line between
VLANs. 2003, Cisco Systems, Inc. All rights reserved. 2-1
VLANs 2003, Cisco Systems, Inc. All rights reserved. 2-1 Traditional Campus Networks Broadcast Domain Collision Domain 1 Collision Domain 2 Bridges terminate collision domains 2003, Cisco Systems, Inc.
2] Chapter 2 Cisco IOS Commands traceroute mac
![2] Chapter 2 Cisco IOS Commands traceroute mac](/thumbs/72/68003916.jpg "2] Chapter 2 Cisco IOS Commands traceroute mac")
2] Chapter 2 traceroute mac traceroute mac Use the traceroute mac privileged EXEC command on the switch stack or on a standalone switch to display the Layer 2 path taken by the packets from the specified
Buy full file at
14 Chapter 2 LAN Redundancy Chapter 2 LAN Redundancy 2.0.1.2 Class Activity Stormy Traffic ( ) Objective Explain the purpose of the Spanning Tree Protocol (STP) in a switched LAN environment with redundant
Lab Troubleshooting VTP Configuration
Lab 4.4.3 Troubleshooting VTP Configuration Topology Diagram Addressing Table Device (Hostname) Interface IP Address Subnet Mask S1 VLAN 99 172.17.99.11 255.255.255.0 S2 VLAN 99 172.17.99.12 255.255.255.0
Lecture (06) Design and Configuration LAN Practicing, working on CISCO equipment. By: Dr. Ahmed ElShafee
Lecture (06) Design and Configuration LAN Practicing, working on CISCO equipment By: Dr. Ahmed ElShafee ١ Dr. Ahmed ElShafee, ACU : Fall 2015, Practical App. Networks II Part I ٢ ٣ SW01 steps firstly connect
Module 9, Assignment 7
Module 9, Assignment 7 7.2.3 Control Router via Console (in Packet Tracer) 1. Prepare a Cisco 1841 Router (see figure 6-9). 2. Prepare a PC for administration. 3. Prepare a console cable and plug the serial
CCENT Study Guide. Chapter 11 VLANs and Inter-VLAN Routing
CCENT Study Guide Chapter 11 VLANs and Inter-VLAN Routing Chapter 11 Objectives The CCENT Topics Covered in this chapter include: 2.0 LAN Switching Technologies 2.4 Configure, verify, and troubleshoot
If this is your first time configuring the switch, you will notice that the Switch IOS is almost identical to Router IOS.
Spanning Tree Lab Objective Create a basic switch configuration and verify it. Determine which switch is selected as the root switch with the factory default settings. Force the other switch to be selected
PT Activity 4.3.3: Configure VTP
Topology Diagram Learning Objectives Investigate the current configuration. Configure S1 as VTP server. Configure S2 and S3 as VTP clients. Configure VLANs on S1. Configure trunks on S1, S2, and S3. Verify
CCNA Layer 2 switching. Revision no.: PPT/2K605/03
CCNA 640-801 Layer 2 switching Revision no.: PPT/2K605/03 What is Switching? It breaks the Collision Domain It takes the packet and forwards to destined port without any modification. Network still remains
Lab 1.4.6B Implementing Port Security
Lab 1.4.6B Implementing Port Security Device Designation Device Name VLAN 1 Address Subnet mask S1 FC-ASW-1 10.0.0.2 255.255.255.0 PC1 Host 1 10.0.0.254 255.255.255.0 PC2 Host 2 10.0.0.253 255.255.255.0