WIRING DIAGRAMS NVIROMON NDCNTRLRS485. Remote Environmental Monitoring and Control for IT equipment. NVIROMON
|
|
- Liliana Armstrong
- 5 years ago
- Views:
Transcription
1 WIRING DIAGRAMS NVIROMON Remote Environmental Monitoring and Control for IT equipment. NVIROMON NDCNTRLRS485
2 Installation and wiring of NVIROMON system Items Quantity Equipment 1 NVIROMON unit 2 Temperature & water probe 4 Flood sensors 1 Power cable 1 Multi IO probe DCNTRLRS485 1 Sagem MA100 1 Door contacts 1 Maglock 1 Exit Button 1 Break Glass 1 12 VDC 3A power supply Third party requirements (Optional) A GSM SIM card is required to activate the GSM messaging and alert system of the NVIROMON unit. Any active GSM or prepaid GSM SIM card can be obtained from a local GSM service provider. Technical information Connector Information RJ45 RF MMCX IEC power inlet 1
3 Installation Procedure See attached wiring diagrams 1. The NVIROMON is a 1U rack mountable unit. (Page 4) Mount the NVIROMON in an available 1U slot inside an allocated cabinet. 2. Power feed connection. (Page 4) Connect the IEC power inlet to an available 230VAC supply. Switch on the backup battery activation switch at the back of the unit. 3. GSM Sim card (optional) Ensure that the mains power feed is switched off and ensure that the backup battery switch, mounted on the back of the unit, is in the off position before fitting the SIM card into the SIM card slot at the bottom of the unit. Connect the GSM external antenna to the RF MMCX connector. 4. Temperature and water probes (Diag. 0 Page 6) Place the two temperature and water probes at required locations. Connect the probes to the NVIROMON probe ports with CAT5 cables. Both ends of the CAT5 cable have RJ45 connectors. 5. Flood sensors (Diag. 0 Page 6) Place the four flood sensors at required locations. Connect the sensors to the temperature and water probe with CAT5 cables. Both ends of the CAT5 cable have RJ45 connectors. Flood sensors from Multi IO probe (Diag. 7-8 Page 7) Place the four flood sensors at required locations. Connect the sensors to the multi IO probe with CAT5 cables. Both ends of the CAT5 cable have RJ45 connectors. 6. Multi IO probe NDCNTRLRS485 (Diag. 2 Page 8) Place the multi IO probe at required location close to the access door. Connect the probe to the NVIROMON probe port with a CAT5 cable. Both ends of the CAT5 cable have RJ45 connectors VDC Power Supply (Diag. 2 Page 8) Place the Power supply at required location close to the access door. Connect the Power supply to an available 230VAC supply. Connect the Power supply to the multi IO probe with a suitable 2 core cable. The cable connects to a 2 pin connector on the multi IO probe. 8. SAGEM MA100 biometric reader (Diag. 5 Page 10) Install the SAGEM MA100 unit at required location outside and close to the access door. Connect the SAGEM MA100 unit with a CAT5 cable to port 5 of the multi IO probe. The CAT5 cable connects to the multi IO probe with a RJ45 connector. Connect the other end of the cable to the SAGEM MA100 unit according to diagram 5 on page 9. 2
4 9. DOOR contacts (Diag. 3-4 Page 9) Install the Door contacts at required location inside the access door. Connect the Door contacts with a CAT5 cable to port 4 of the multi IO probe. The CAT5 cable connects to the multi IO probe with a RJ45 connector. Connect the other end of the cable to the Door contacts according to diagram 3-4 on page EXIT button (Diag. 3-4 Page 9) Install the EXIT button at required location inside the access door. Connect the EXIT button with a CAT5 cable to port 3 of the multi IO probe. The CAT5 cable connects to the multi IO probe with a RJ45 connector. Connect the other end of the cable to the EXIT button according to diagram 3-4 on page BREAK GLASS contacts (Diag. 6 Page 11) Install the BREAK GLASS contacts at required location inside and close to the access door. Connect the BREAK GLASS contacts with a CAT5 cable to port 6 of the multi IO probe. The CAT5 cable connects to the multi IO probe with a RJ45 connector. Connect the other end of the cable to the BREAK GLASS connectors according to diagram 6 on page MAGLOCK (Diag. 6 Page 11) Install the MAGLOCK at required location inside the access door. Connect one end of a CAT5 cable to the FIREMAN S SWITCH contacts. Connect the other end of the cable to the MAGLOCK contacts according to diagram 6 on page 10. 3
5 NVIROMON MAIN WIRING DIAGRAM 4
6 Equipment Location at Access Door 5
7 6
8 7
9 8
10 9
11 10
12 11
WIRING DIAGRAMS. Installation and wiring of NVIROMON system NVIROMON MULIODCBPSU. Remote Environmental Monitoring and Control for IT equipment.
WIRING DIAGRAMS NVIROMON R12 Remote Environmental Monitoring and Control for IT equipment. NVIROMON MULIODCBPSU Installation and wiring of NVIROMON system ITEMS Quantity Equipment 1 NVIROMON unit 4 Temperature
More informationIEI emerge MicroNode Install and Setup Guide. Contents
IEI emerge MicroNode Install and Setup Guide Contents Connecting power and the network to the MicroNode... 2 Using Power over Ethernet (PoE)... 3 or... 3 Using a 12 VDC power supply... 3 Connecting and
More informationSelf-Contained Equipment Cabinets
Self-Contained Equipment Cabinets The water and dust proof self-contained cabinets houses all the services required to service, power backup and protect your network core or distribution equipment required
More informationQuick Start Guide. SEB-710 I/O Expansion board. Introduction
SEB-710 I/O Expansion board Revision 1.0 - (March, 2011) Saflec Systems (Pty) Ltd Quick Start Guide Introduction The SEB-710 is an I/O expansion device for additional inputs and outputs. It has eight relay
More informationKAUGJUHTIMISSÜSTEEMID TELECONTROL SYSTEMS MODEM TELEM-GSM/GPRS 3G. User manual
KAUGJUHTIMISSÜSTEEMID TELECONTROL SYSTEMS MODEM TELEM-GSM/GPRS 3G User manual Martem AS 2014 CONTENTS 1. Description...3 2. Features...3 3. Interfaces...3 4. Indication and switches...4 4.1 State LED indication...4
More informationIP68. Autarkic Data Loggers - MT-051 / MT-713 / MT-723
Autarkic Data Loggers - MT-051 / MT-713 / MT-723 Use in the most demanding environments These data loggers are designed for use in difficult to reach and widely distributed locations. In places where neither
More informationModule Technical characteristics
Module Technical characteristics Power supply 220VAC Average power consomption 0.1W Peak power consumption 25W Battery 1400mAh :(charge average about 3 days ) 4 Input opto-isolated 220AC o 12VDC 4 separated
More informationWing Watch Lite. Battery Monitoring System. User Manual
Wing Watch Lite Battery Monitoring System User Manual February 2009 Check the contents: The Wing Watch-Lite is packed in soft, protective material inside a carton box. There are 5 sets in each packaging.
More informationDomain 3000 Back Panel
Domain 3000 Back Panel The Domain 3000 has 25 I/O ports plus a connector for an external power supply (included) and an LED to indicate that the power is on. Typically, it is placed on a shelf or equipment
More informationEntryphone. PinNet 4. Product manual. October 2010 R Granville Road, London SW18 5SD
Entryphone PinNet 4 Product manual October 2010 R4.9 www.entryphone.co.uk 23 Granville Road, London SW18 5SD This document covers the installation and use of the Entryphone on-line PinNet door control
More informationTECHNICAL DESCRIPTION
MPi80HD TECHNICAL DESCRIPTION 1 GENERAL DESCRIPTION The MPi80HD system is designed to convert AC mains voltage into 48 VDC and to supply telecom equipment with battery back up. The MPi80HD can house up
More informationDKG-210 UNIVERSAL INTERNET GATEWAY UNIT
DKG-210 UNIVERSAL INTERNET GATEWAY UNIT AC & DC SUPPLY VERSIONS DESCRIPTION The DKG-210 is designed for internet monitoring and control of industrial devices using different protocols through the RAINBOW
More informationTechnical Manual Nova: Cabinet Security Management System (CSMS)
Technical Manual Nova: Cabinet Security Management System (CSMS) KP_nova_TM_160501_EN 1 Publication May, 2016, Keyprocessor BV Paasheuvelweg 20 1105BJ Amsterdam, The Netherlands www.keyprocessor.com/nova
More informationENVIROMUX Series Installation Instruction For:
ENVIROMUX Series Installation Instruction For: ENVIROMUX-IMD(-P) INFRARED MOTION SENSOR ENVIROMUX-IMD-CM(P) CEILING MOUNT MOTION SENSOR ENVIROMUX-IMD-TAA INFRARED MOTION SENSOR-TAA COMPLIANT ENVIROMUX-GBS(-P)
More informationUser Manual Revision 1.02
User Manual Revision 1.02 Manufactured by Contents 1. Introduction... 4 2. Disclaimer and Warranty... 4 3. Specifications... 5 4. Features... 5 5. Quick Start Guide... 6 5.1 Hardware... 6 5.2 Software...
More informationNetGen Hardware Installation Guide. for NetGen Ethernet Door Controllers
NetGen Hardware Installation Guide for NetGen Ethernet Door Controllers 0613 Table of Contents BLUEWAVE SYSTEM OVERVIEW...2 THE WI-FI LOCK AND SECURITY COMPANY...2 NETGEN DOOR CONTROLLERS...2 INSTALLATION
More informationCMi- box. M-Bus Metering Gateway for Mobile Network GSM/GPRS TCP/IP. CMi-Box
CMi Series CMi-Box CMi- box M-Bus Metering Gateway for Mobile Network The CMi-Box is a flexible solution for collection of meter values which can be customized to meet each individual customer s needs.
More information1. Product Specification
1. Product Specification Item Specification Voltage 12VDC +10%, Current 1.2A Lock Relay 12VDC/2A Environmental Temperature working:0 ~45 ; storage:-10 ~55 Relative humidity working:40%~90%rh; Card Capacity
More informationSierra Radio Systems. Digital Compass. Reference Manual. Version 1.0
Sierra Radio Systems Digital Compass Reference Manual Version 1.0 Contents Digital compass board RS485 power injector For more information, go to the Sierra Radio Systems web site at www.sierraradio.net
More informationthe Interactive Catalog
Interactive Catalog Supplements Catalog PDFs If you need detailed product information, or help choosing the right product for your application, see our Interactive Catalog Use the Interactive Catalog to
More informationFerrous metal (The sensing distance decreases with non-ferrous metal.) Power supply voltage (operating voltage range)
Description The sensors provide excellent results even with difficult-to-detect objects, e.g. small or thin parts, wires or bright metals. A variety of types cover a wide range of individual requirements
More informationH3G-380 Production Description
H3G-380 Production Description Designed for UPS battery strings of 15 to 48 batteries each of VRLA and Ni-Cd battery 1 Applications For strings of 15 to 48 batteries each Data Center IT Data Room 2 Product
More informationUC-2000 Installation Manual Unicorn Computers Technology Limited
UC2000 Installation Manual Copyright 2003. All rights reserved. Table of Contents Specifications 2 Enclosure for the UC2000 Controller 3 Unicorn Access Control System Configuration 4 UC2000 Controller
More informationT-Monitor E-Monitor TABLE OF CONTENTS SECTION 1 - DESCRIPTION...2 SECTION 2 - SPECIFICATIONS...3 SECTION 3 - INSTALLATION...5
T-Monitor E-Monitor TABLE OF CONTENTS SECTION - DESCRIPTION... SECTION - SPECIFICATIONS...3 SECTION 3 - INSTALLATION... SECTION - FRONT PANEL INDICATORS...7 SECTION - INTERFACE SIGNALS AND CABLES...8 SECTION
More informationLab 5: Access Control Training Station
Lab 5: Access Control Training Station Learning Objectives At the end of the lab, trainees should be able to: 1. Understand the functional block and hardware of an access control system. 2. Understand
More informationPQ-Box 100, 150, 200 & 300 Power Quality Analyser Clamps & Accessories
Mini Clamps: Part Number 111.7015 PQ-Box 100, 150, 200 & 300 Power Quality Analyser Clamps & Accessories Description 10 ma-to-20 A or 100 ma-to-200 A. Switchable range mini clamp. 40 Hz 20 khz 4 x mini
More informationTHE BRIDGE. Make any Wiegand device wireless with the Sure-fi Bridge FEATURES. Technology
THE BRIDGE Make any Wiegand device wireless with the Surefi Bridge *Housing options sold separately. Keep your Wiegand system connected. Fix faulty Wiegand systems quickly and easily with our wireless
More informationAC5160 SiPass integrated controller kit
AC5160 SiPass integrated controller kit SiPass integrated Wall housing with pre-assembled basic SiPass integrated components Equipped with one ACC (AC5100), two dual reader interfaces (ADD5100) and one
More informationBMCS CCX Cabinet. BMCS_CCX Cabinet is secured via a switchable 6A circuit breaker. Note the right selectivity ratio of your feeding.
Version: 2011-01-13 BMCS CCX Cabinet Description & Function: The BMCS_CCX Cabinet is a ready to install wall housing for one or more BMCS systems (see figures 1 to 3). The BMCS_CCX Cabinet is designed
More informationFACIAL RECOGNITION TERMINAL SYSTEM
StoneLock is a global leader in designing and manufacturing secure access control solutions. We are proud to build and design the most secure, reliable and user-friendly access control products for both
More informationCOPPER-T EXTENDER TABLE OF CONTENTS SECTION 1 - DESCRIPTION SECTION 2 - SPECIFICATIONS... SECTION 3 - INSTALLATION
COPPER-T EXTENDER TABLE OF CONTENTS SECTION - DESCRIPTION...... SECTION - SPECIFICATIONS...... 3 SECTION 3 - INSTALLATION...... SECTION - FRONT PANEL INDICATORS... 7 SECTION - INTERFACE SIGNALS AND CABLES...
More informationTIME SERVER NETSILON. Quick start.
TIME SERVER NETSILON Quick start This document refers to the following products: 907,900 NETSILON 7 (100-240 VAC) 907,901 NETSILON 7 (18-36 VDC) 907,902 NETSILON 7 (100-240 VAC + 18-36 VDC) www.bodet-time.com
More informationTAPR GPS Kit USER S GUIDE
TAPR GPS Kit USER S GUIDE GPS Kit parts derived from the original Synergy Systems, LLC SynPaQ/E M12+ version Shipped as-is without Warranty These GPS Kit parts were previously used in a timing application
More informationSee it. Control it. The TelPro Solution
See it. Control it. The TelPro Solution JANUARY 2017 Introducing the TelPro Solution A combined cellular and wireless IoT gateway and cloud portal system Collection and analysis of commercial and industrial
More informationUser Manual IDD-213TH
User Manual IDD-213TH On your cellphone go to Play Store or APP Store. Search for Lit guardian and download/install. Install a standard SIM card with no pin code in device (CDMA unsupported). Place IDD-213TH
More informationGSM Voice Active Monitoring OTP-GSM89
GSM Voice Active Monitoring OTP-GSM89 1 Feature: 1. Voice active monitoring, when detect voice level higher then voice setting sensitivity, the module will send SMS and making call automatically. 2. Can
More informationThe 3-phase, 5-wire model name is PF LNM. The 3-phase, 4-wire model name is PF LNN.
The 12.5kW power shelf accepts 3-phase input power and provides stable DC output power (1000A at 12.5VDC). The OCP 21-inch power shelf includes a total of 5+5 high-power, hot-swappable PSUs in redundant
More informationUSP-070-B08 USP-104-B10, USP-104-M10 USP-156-B10
UniStream HMI Panel Installation Guide USP-070-B10, USP-070-B08 USP-104-B10, USP-104-M10 USP-156-B10 Unitronics UniStream platform comprises control devices that provide robust, flexible solutions for
More informationPDU Solutions. PDU Solutions
Canovate offers a full range of PDU s from basic and metered ones to IP PDU s with per socket switching capability and wireless sensor connectivity. Our PDU s can be used in the most complex ISP and Colocation
More informationEdaFastCam The Smart Clip-on Meter Reader for Home and Business
EdaFastCam The Smart Clip-on Meter Reader for Home and Business power of technology UNIVERSAL For all mechanical electricity, gas and water meters SIMPLE OCR-assisted install mechanism makes installation
More informationInstallation Instructions. i-net Access Control Units. Part Code: IA-PCB IA-ACB IA-ACU IA-KIT
Installation Instructions i-net Access Control Units Part Code: IA-PCB IA-ACB IA-ACU IA-KIT This device is configured for DHCP. Identity Access software will find this device, go to setup and controller,
More informationM2M Control C350 Professional
M2M Control C350 Professional The C350 is a invaluable powerful M2M Platform! wide and universal I/O interface digital and analog I/O, S0 and I/O extension modules versatile interfaces and powerful protocols
More informationVT825 / Environmental Monitoring unit. Environmental Infrastructure monitoring
Environmental Infrastructure monitoring VT825 / Environmental Monitoring unit The unit is used for IT environmental control in data-centers, remote facilities, offices, industrial facilities & remote shelters.
More informationStatement of compliance no 40/2011
-1- ST-65 module GSM v1.0.7 Statement of compliance no 40/2011 We, the company TECH, headquartered in Wieprz 1047A, 34122 Wieprz, declare with full liability, that the controller ST 65 GSM, produced by
More informationIPassan Installation guide
IPassan Installation guide 1 Content 1 Overview... 3 1.1 Features... 3 1.2 Hardware... 3 1.2.1 s... 3 1.2.2 Extra modules... 5 1.3 IPassan manager... 7 2 Installation... 7 2.1... 8 2.1.1 Power supply...
More informationEZ-TAG2 Manual_Layout 5 11/12/ :14 Page 1 U S E R M A N UAL
EZ-TAG2 Manual_Layout 5 11/12/2012 09:14 Page 1 USER MANUAL EZ-TAG2 Manual_Layout 5 11/12/2012 09:14 Page 2 Contents EZ-TAG2 and Back Plate 1 x Security Torx Key 4 x Screws and raw plugs 1 x Marking out
More informationWT-380 Automated Switching Solution For 48 Twisted Pairs or 40 Twisted Quad Cables
WT-380 defines multi-line, vectored performance testing of Gfast modems using profiles 106 or 212. This is done over 48 (or 40) short or long loops of twisted pair (or twisted quad) cables. The Telebyte
More informationThe INJ-102GT-24V PoE Injector is an advanced IEEE802.3at compliant device with intelligent detection that provided
Industrial 2-port Gigabit High Power PoE Injector, 24V~50V Input Support Features Supports 2x10/100/1000Base-T(X) for power and data Output Fully compliant with IEEE802.3at/802.3af standard Auto protection
More informationCommunication Interface
Communication Interface Com'X 200 Technical data sheet Communications Functions and characteristics PB112041 Ethernet GPRS data logger function The collects and stores wages consumptions (Water, Air, Gas,
More informationFAST EnergyCam. The Smart Clip-on Meter Reader for Home and Business
The Smart Clip-on Meter Reader for Home and Business Retrofit rather than replace Smart metering power in a tiny, beautifully-designed package The quick and inexpensive way to turn your conventional meter
More information1. Introduction. 2. Product Overview Appearance Buttons/Mini USB Interface Description. UBI5000E User Manual
1. Introduction UBI5000E is a powerful GPS locator which is designed for vehicle, pets and assets tracking. With superior receiving sensitivity, fast TTFF and GSM frequencies 850/900/1800/1900. Its location
More informationTechnical Documentation, RTCU-SA
Technical Documentation, RTCUSA The RTCUSA product (GSM antenna not included in product) The RTCUSA product is a RTCU unit with a builtin communications module such as GSM, DECT or FSK Modem. The RTCUSA
More informationGSM Controller BR160SM-2FLOW-4A-A / BR161SM-2FLOW-4A-A Preliminary data
GSM Controller BR160SM-2FLOW-4A-A / BR161SM-2FLOW-4A-A Preliminary data Version for flow (pulses), analog and digital signal monitoring GSM module for SMS remote monitoring and control applications Features
More informationSMS TEXT DIALLER INSTALLATION AND OPERATION MANUAL
SMS TEXT DIALLER INSTALLATION AND OPERATION MANUAL Flashing Light (Text Message Received) Permanent Light (In Alarm) Optional Battery Backup SIM Card Carrier (see how to insert SMS card later in this manual)
More informationThe Packs Infotel. GSM Converter V2. Installation Manual V7
The Packs Infotel GSM Converter V2 Installation Manual V7 1 Index Connecting the M60 to the GSM Converter 3 1. GSM Converter description 4 2. Equipment installation 4 3. Led functions. 5 4. GSM Converter
More informationUniStream HMI Panel. CPU-for-Panel
UniStream HMI Panel Installation Guide USP-070-B10,USP-104-B10, USP-156-B10 Unitronics UniStream platform comprises control devices that provide robust, flexible solutions for industrial automation. This
More informationConverter Box Data Sheet
Page 1 from 6 Functions of the converter box The converter box is used to adapt physically two interfaces and to separate them galvanicly. It is configured as follows: Two interface slots can be used to
More informationWiring and Configuration Instruction
Wiring and Configuration Instruction This ENVIROMUX Sensor is intended for connection to an NTI ENVIROMUX-MINI-LXO /-16D / -5D/-2D for use in detecting changes in the environment. When properly connected,
More informationI/O Expansion Module Installation & Reference
Overview The In-Sight vision sensor supports up to ten discrete inputs and ten discrete outputs. Two inputs and two outputs are built-in to the In-Sight processor. The remaining eight inputs and outputs
More informationGSM Controller BR160SM-Sd BR161SM-Sd V1.2
GSM Controller BR0SM-Sd BRSM-Sd V. Standard version for digital signal monitoring GSM module for SMS remote monitoring and control applications Alarm Notification Remote Control www.bieneelectronics.com
More informationFeatures. Reliable High RF Shielding. Pneumatic control of lid open-close and optional test fixture motions
TC-5972AP/CP Pneumatic Shield Box Features Reliable High RF Shielding Pneumatic control of lid open-close and optional test fixture motions Easily customizable to meet various test needs Shock Absorbers
More informationDIRIS Digiware D and C Communication and control power interfaces
Multi-circuit metering and measurement diris-dw_006_a_us_cat diris-dw_142_a The solution for > Industry > Building > Infrastructure > Data centers DIRIS D-40/D-50/D-70 Centralization and display of data
More informationEP-ELVCTL Elevator Control (NION-16C48M)
EP-ELVCTL Elevator Control (NION-16C48M) Product Installation Document This document covers the procedures and specifications for installing the above listed unit and when appropriate, information regarding
More informationProduct description The SWH is a board Cellular Terminal solution for GSM GPS/GLONASS
SWH Product description The SWH is a board Cellular Terminal solution for GSM GPS/GLONASS Rev.1 01/03/2013 1. Overview The SWH is a complete board Cellular Terminal solution for GSM GPS/GLONASS applications.
More informationNGSMPM-PH1 - Simple GSM Power Monitor PH1 User Manual
User Manual The GSM single phase utility power monitor is used to monitor the mains power at your premises, simply plug the unit into one of the power plugs. Install a SIM and SMS your cell phone number,
More informationUSER MANUAL. Mobeye WaterGuard-FS. Float sensor CM2300FS. SW version 5.n
USER MANUAL Mobeye WaterGuard-FS Float sensor CM2300FS SW version 5.n CONTENT 1. General description 4 2. Getting started 5 2.1 Insert a SIM card 5 2.2 Connect a sensor to the input 6 2.3 Insert the batteries
More informationUp to 4 x Temperature Monitoring Probes with Control Cable (1 Included) User set point control, display for Rack Face Temperature
4 x EC Fans Power feed Tool less Stringer Hangers User Temperature Control Interface Up to 4 x Temperature Monitoring Probes with Control Cable (1 Included) Imperial -Fan Assist SPECIFICATIONS General
More informationSafeLine GL5. Installation manual. A GSM alternative for all of our lift telephones with built-in power supply and battery backup.
SafeLine GL5 Installation manual A GSM alternative for all of our lift telephones with built-in power supply and battery backup. SafeLine GL5 Installation manual TECHNICAL DATA Communication: Antenna connector
More informationTime Counters mini "h", DC Version
Type 633-DC Time Counters mini "h", DC Version Type 633.0 Type 633.7 Type 633.8 High shock resistance Miniature dimensions Electrical connections in standard grid Suitable for PCB mounting Machine-solderable
More informationPT2060 Monitor. PT2060/91 SIM System Interface Module. Specifications. Electrical. Messtechnik
PT2060/ System Interface Module ProvibTech s PT2060/ module is a communication and system interface module. This module is used to: module. The two phase reference channels can be used to provide phase
More informationMT550 Cat M1/NB1 GPS Tracker User Manual V2.0
MT550 Cat M1/NB1 GPS Tracker User Manual V2.0 Preface Congratulations on choosing the Mictrack MT550 Cat M1/NB1 GPS tracker. This manual shows how to easily program and setup the tracker for best results.
More informationMicro Instruments price list All pricing excludes 15%
Micro Instruments price list All pricing excludes VAT @ 15% - 2019 Product Description Solar Smart R1 Solar MPPT regulator 12/24V - 20Amp with R2 799.00 5 Way Relay board R360.00 Ethernet + SNMP support
More informationARVO-TEC OY. Control System
ARVO-TEC OY Control System ARVO-TEC FEEDING NETWORK FEEDING PROCESS MANAGEMENT VIA WEB BASED INTERFACE ALL INFORMATION IN ONE DATABASE REMOTE ACCESS - ACCESS YOUR SYSTEMS ONLINE DATALOGGING ALARMS VIA
More informationUP200-GSM Intercom and access control unit operating on mobile GSM network
UP200-GSM Intercom and access control unit operating on mobile GSM network INTRODUCTION The UP200-GSM is an intercom unit which as a cell phone can call the owner s mobile or landline phone. By pressing
More informationBLU- CIF Interface Board
BLU- CIF Interface Board The BLU-CIF Interface Board simplifies the wiring of all of the BLU products to the BSS Audio London Series Digital Signal Processors. It allows for Cat5e wiring termination, as
More informationGSM controller module for SMS remote monitoring, alarming and control applications BR900-ST. Preliminary data. GSM module BR900-ST.
GSM controller module for SMS remote monitoring, alarming and control applications BR900ST Preliminary data Introduction The BR900ST controller is a low dimensions low cost GSM communications device that
More informationVersaMax IP. Proficy Machine Edition. Publication Reference Chart
Distributed I/O is designed to offer the ruggedness and reliability of a standard I/O system installed in a NEMA 4 cabinet, without the cost and effort to build the cabinet. is IP67 rated so it can be
More informationMetaDolce MD3600 IP65 Multi-Data Capture Tablet Quick Manual. 1. Keys and Connectors
1. Keys and Connectors 1 2. Technical Specifications 2 3. Product Use Recommendations 3.1 Attention: Only use the charger supplied by the manufacturer to recharge the device, other chargers may cause damage.
More informationHardware manual. 1. Overview 2. Technical characteristics 3. Connections. ( Portal (../portal/portal.html)
1 (http://nethix.com) Portal (../portal/portal.html) WE110 (../we110/we110.html) WE120 (../we120/we120.html) WE300 (../we300/we300.html) WE500 (we500.html) Quick start guide (we500_qsg.html) Hardware manual
More informationType K/J Thermometers
Type K/J Thermometers 800005 CONTENTS INTRODUCTION....2 FRONT PANEL DESCRIPTION...3 LCD DISPLAY....4 OPERATION INSTRUCTION...5 Power Up....5 Connecting the Thermocouples....5 Selecting Temperature Scale....5
More informationConversion of Contact ID event codes sent by alarm control panel via GSM and PSTN channel to SMS messages
GSM ProCom Description GSM and PSTN communication Management of 2 independent SIM cards Reception of incoming calls, possibility for restriction Installable behind PBX Management of different prefix numbers
More informationGrow your business by providing an intuitive home safety and comfort experience
Grow your business by providing an intuitive Self-contained, wireless security and interactive home automation system Fire detection s Video cameras Locks S.O.S./panic buttons Key features and benefits
More informationLCD-1 CD-LCD1-01 PRODUCT OVERVIEW. Product. Description. Specifications SKU: LCD-1. 5-Button Scene Controller
CD-LCD1-01 LCD-1 Product 5-Button Scene Controller Description The Evolve 5-Button Scene Controller is a programmable device that provides command and control of up to 5 (RF) network scenes and it s a
More information10/100 AUTO-SENSING MEDIA CONVERTERS
NxTFAUTOxxx 10/100 AUTO-SENSING MEDIA CONVERTERS 10/100Mbps with auto-negotiation. - or single- versions available. No delays. Front-panel diagnostic LEDs. Auto-sensing. Available in table-top, industrial,
More informationACCESSORIES. Driver Mounting Clips. OWA-60U-24 (pg. 6) Flat; Corner (pg. 5) Wire Size PERFORMANCE
CLOSET RATED is a high performance LED fixture suitable for use in closets, under cabinets, and in shelving. has a built-in motion sensor that activates the light without the need for a wall switch or
More informationAccess Easy Control System. Reference Guide
Access Easy Control System Reference Guide Content 3 1. AEC System Overview 4 2. AEC Main Components 6 3. AEC Configuration 7 4. AEC Benefits 8 5. AEC Easy Ordering 10 6. AEMC More than 16 readers? 12
More informationACCESSORIES. Driver Mounting Clips. OWA-60U-24 Flat; Corner Wire Size PERFORMANCE. Field of View CRI Lumen Maintenance Binning Tolerance Warranty + +
NITELIGHT is a high performance LED fixture suitable for use in closets, under cabinets, and in shelving. NITELIGHT has a built-in motion sensor that activates the light without the need for a wall switch
More informationHUDGE STORAGE MEMORY TO CATER FOR FUTURE EXPANSION OPTO ISOLATION FOR BETTER NOISE PROTECTION
CUSTOMISED ENCLOSURE BEAT - 200 32 BIT CPU CONTROLLER 128MB INTERNAL MEMORY 2 x 16 CHARACTER LCD BACKLIGHT DISPLAY ISO 14443 TYPE A&B READ SUPPORTED MIFARE SUPPORTED MULTIPLE LED LIGHT INDICATOR 4 x 4
More informationUp to two expansion cards can be added; these cards may either add an additional 4 analogue or 8 digital inputs.
SA380TX-L Hardware The basic TX-L unit features: 4 digital inputs 2 analogue inputs 1 RS485 port 24v 2W auxiliary power supply GSM modem. An Ethernet port can be fitted as an option when ordering. Up to
More informationPeristaltic Cased Tube Pump
Peristaltic Cased Tube Pump Selectable Output Control Functionality and Setup Version 1.0v-11/2016 Print-No. 01 Table of Contents 1. Introduction 2. Powering the Input/Output Port 2.1 Wiring for Local
More informationD O O R S T A T I O N W I T H P R O X I M I T Y R E A D E R
D O O R S T A T I O N W I T H P R O X I M I T Y R E A D E R Table of contents Planning and installing the Enterview VX............................ 3 Wiring Diagram.....................................................
More informationx x 60 mm, 700 gm. Wall mounted enclosure, 1 Kg. Weatherproof, high impact GF ABS. Remote control and monitoring with debug features
Smart Hub Intelligent Energy Management and IoT Hub Unit (CT200i) General Dimension and weight 202.73 x 267.45 x 60 mm, 700 gm Dimension with standard cover 268 x 204 x 56 mm Dimension with weatherproof
More informationPrice List MSRP. Bundle price, save $15. Non- Discountable
sensorprobe SENSORPROBE 2 (SP2) * sensorprobe2 SP2 $250 sensorprobe2 with PoE option SP2POE $295 sensorprobe2 with 1ft temperature sensor SP2T01 $295 sensorprobe2 PoE with 1ft temperature sensor SP2POET01
More informationChassis-based Media Converters
Media Converters with Individual Metal Case Housing. DMC-615SC DMC-1002 Management Module DMC-1000 Chassis Chassis-based Media Converters System Overview The Chassis-based Media Converters include a number
More informationRackmount LCD Console - 1U - 17in Screen - US Keyboard p
Rackmount LCD Console - 1U - 17in Screen - US Keyboard - 1080p Product ID: RKCOND17HDEU This 1U LCD console offers a space-saving solution for managing and monitoring your DVI or VGA servers and KVM switches
More informationfor Sagem SIGMA Readers
Galaxy Configuration guide for Sagem SIGMA Readers Compatible with Galaxy Hardware for new & existing installations Galaxy supports Legacy mode in SG 10.3.1 or higher Page 1 of 9 System Galaxy Version
More informationRemote Console Manager with GSM Modem QS Guide
LES1204A-3G-R2 Remote Console Manager with GSM Modem QS Guide Quick Start Guide This Quick Start Guide helps you through installation, configuration, and local operation. For more details, refer to the
More informationConnecting a Cisco Input Module
CHAPTER 4 Overview The optional Cisco Input Module (Figure 4-1) is attached to a Cisco Physical Access Gateway or Cisco Reader Module to provide additional connections for up to ten input devices. Each
More informationSitePORTAL Lite TA-SPL32-R48
SitePORTAL Lite TA-SPL32-R48 Quick Connect Guide The TA-SPL32-R48 is a 19 inch, 2 RU rack mountable siteportal Lite (spl). It comes with 8 analog inputs, 8 temperature inputs (sensors sold separately),
More informationCorning Optical Network Evolution (ONE ) Solutions Mid-Power Remote Expansion Unit (MxU)
features and benefits Supported service Supported channels Expands mid-power remote unit (MRU) services Optical fiber savings Design and deployment flexibility Scalable Design Simple installation and maintenance
More information