TRFTTE. ISDN Gateway A104 / A104D / A104E / A104DE / RSVLC-1002B A108 / A108D / A108E / A108DE. Nemko Canada Inc.

Transcription

1 Report reference No TRFTTE Test item description Model ISDN Gateway A104 / A104D / A104E / A104DE / RSVLC-1002B A108 / A108D / A108E / A108DE Testing Laboratory Address Nemko Canada Inc. 303 River Road Ottawa, Ontario, Canada, K1V 1H2 +1 (613) Applicant's Name Address Sangoma Technologies 50 McIntosh Drive, Suite 120, Markham, Ontario L3R 9T3 CANADA Test specification TNA 134:1997 (ISDN L3, New Zealand) ISDN Layer 3 Supplementary testing Access standards Newsletter No. 125 Appendix No. 1 Tested by Kurt Mikolajewski Telecom specialist Approved by Stuart beck Director of Certification Date of issue 22 June 2010 Number of Pages 24 This test report shall not be reproduced in any form except in full without the written approval of the Test Laboratory.

2 Table of contents 1 Client information Equipment details Test project performance Test report summary Equipment under test EUT Description Technical judgement Modification performed during the assessment Additional observations Samples Submitted for testing Test laboratory description Test equipment used Photographs of test samples A104 Connector view A104 Base card bottom view A104 Base card Top view A104 Line Interface Card Top View A104 Line Interface Card Bottom view A108 Line Interface Card top view A108 Line Interface Card bottom view Requirement conditions table Test results summary Detailed test results...16 Page 2 of 24

3 1 Client information Client name: Sangoma Technologies Address: 50 McIntosh Drive, Suite 120, Markham, Ontario L3R 9T3 CANADA Telephone: Fax: Contact name: Bruno Fagundes 2 Equipment details Product name: Product type: Model(s): Samgoma T1/E1/J1 cards ISDN Gateway A104 / A104D / A104E / A104DE / RSVLC-1002B A108 / A108D / A108E / A108DE 3 Test project performance Project ID: Location: Test started: Test specification(s): Test suite: TRFTTE Nemko Canada 303 River Road, Ottawa, Ontario K1V 1H2 2/17/ :05:00 AM TNA 134:1997 (ISDN L3, New Zealand) TNA 134:1997 (ISDN L3, New Zealand) (3/12/2009, modified) Page 3 of 24

4 4 Test report summary Testing was completed against all relevant requirements of the test standard. The results obtained indicate that the product under test does comply in full with the requirements tested. The test results relate only to the items tested. 5 Equipment under test 5.1 EUT Description The EUT is a PC based VoIP Gateway card. It provides public telecommunication network access via up to 8 Primary Rate ISDN ports. The card has different variants, which allows the card to host the following configurations: 4 ports Model A104. The differences between models are the addition of a DSP for echo cancellation or the use of PCI Express as opposed to PCI architecture 8 ports Model A108. The differences between models are the addition of a DSP for echo cancellation or the use of PCI Express as opposed to PCI architecture The A104 is a depopulated version of the A Technical judgement The following technical judgements were made during the assessment: Technical judgement 1 The EUT has already been evaluated for compliance to TBR4 (Ref. Nemko Canada report TRFTTE) and therefore it was judged that only the supplementary L3 tests from the Access standards Newsletter No. 125 Appendix No.1 apply. 5.3 Modification performed during the assessment The following modifications were made during the assessment: Modification 1 The product as submitted did not support the Progress Indicator for analog ports. The S/W was modified to provide the Progress Indicator Call is not endtoend ISDN for calls to or from analog port. 5.4 Additional observations Software Version:6,0,13,1 Connector: 8 pin modular type Transformer: PULSE TX1475NL Framer / Transceiver: DALLAS, PN: DS26528 (for A108), DS26524 (for A104) Page 4 of 24

5 5.5 Samples Submitted for testing The following samples have been for type assessment: Sample Description Model Number Serial Number 1 A200 PCIe card with FXO modules A200-2 RJ11 adaptor cables for A HOST - Desktop PC (windows XP) port ISDN PCIe card A The first samples were received on: June 1 st, Test laboratory description Nemko Canada Inc., a testing laboratory, is accredited by the Standards Council of Canada. The tests included in this report referencing TBR 4 are within the scope of this accreditation. 7 Test equipment used Description Model S/N Hardware Rev. Software Rev. Last Calibration Telecom Conformance Analyzer Hermon Laboratories TCA 8200 FA A , build 2460, Thu 03/25/ :49: /5/2010 9:45:53 AM Page 5 of 24

6 8 Photographs of test samples Photographs were taken of relevant samples during the assessment. These are detailed below and are included in this section. 8.1 A104 connector view 8.2 A104 Base card bottom view 8.3 A104 Base card top view 8.4 A104 Line Interface Card top view 8.5 A104 Line Interface Card bottom view 8.6 A108 Line Interface Card top view 8.7 A108 Line Interface Card bottom view The photographs depict the samples as originally submitted. Page 6 of 24

7 8.1 A104 Connector view Page 7 of 24

8 8.2 A104 Base card bottom view Page 8 of 24

9 8.3 A104 Base card Top view Page 9 of 24

10 8.4 A104 Line Interface Card Top View Page 10 of 24

11 8.5 A104 Line Interface Card Bottom view Page 11 of 24

12 8.6 A108 Line Interface Card top view Page 12 of 24

13 8.7 A108 Line Interface Card bottom view Page 13 of 24

14 9 Requirement conditions table Condition TNA 134:1997 (ISDN L3, New Zealand) (3/12/2009, modified) Applies No ISDN Layer 3 Supplemental Testing (Newsletter No. 125 Appendix No. 1) Yes Page 14 of 24

15 10 Test results summary Test TNA 134:1997 (ISDN L3, New Zealand) (3/12/2009, modified) TNA 134:1997 (ISDN L3, New Zealand) Layer 3 requirements Status Not Tested See TBR4 report Nemko Canada TRFTTE ISDN Layer 3 Supplemental Testing (Access Standards Newsletter No. 125 Appendix N0. 1) I Applicable to all ISDN CPE 1. Redirecting Number IE Accepts call with Redirecting number information in the Setup message Pass 2. Date and Time IE Accepts call with time and date in the Setup message Pass Accepts call with time and date in the Connect message Pass II Only for EUTs intended to support Telecom CENTREX 1. Feature activation IE Not Supported 2. Called Number type and plan Not Supported III Only for EUTs with Analog ports (Terminal adapters) 1. Outgoing call from Analogue port Setup message including Progress Indicator IE Pass Page 15 of 24

16 11 Detailed test results Page 16 of 24

17 Test specification: Test purpose: Test mode: Redirecting Number IE (Information Element) Project No.: TRFTTE The test checks that calls with the Redirecting number information element in the SETUP message are accepted by the EUT. The extraction and processing of the redirecting information element is left to the equipment supplier. This is a subscription option. Compliance Date & Time: 3/17/2010 Verdict: PASS Temperature: 26 C Air Pressure: 99.5 kpa Relative Humidity: 33 % Mains Power Supply: 230Vac 50Hz Remarks: Redirecting Number IE (Information Element) 17:38:49/ Q931 ID:O,1 - User Indication (0): Outgoing call #1 Incoming call 17:38:49/ RS D1 BOP FRAME flg=999 [0039] D2 Q921 (S:00 T:000 C/R:1) I P:0 NR:000 NS:000 [0035] D3 Q931 Pro:08 Ref:(O,00 01) SETUP IE:(0/04) len:3 >> Bearer capability Oct 3 : Coding = ITU-T Capability = Speech Oct 4 : Transfer mode = Circuit Transfer rate = 64 kbits/s Oct 5 : L1 protocol = G711 A-law IE:(0/18) len:3 >> Channel identification Oct 3 : Int id = implicit Interface = Primary Preferred/Exclusive = Exclusive Channel select = Indication follows Oct 32: Coding = ITU-T Number/Map = Number Type = B-channel Oct 33: Channel number = 1 IE:(0/29) len:5 >> Date/time Oct 3 : Year = 10 Oct 4 : Month = 1 Oct 5 : Day = 13 Oct 6 : Hour = 9 Oct 7 : Minute = 38 IE:(0/70) len:5 >> Called party number Oct 3 : Type of number = Unknown Numbering plan= Unknown Oct 4 : ******** Number = 1234 IE:(0/a1) len:0 >> Sending complete IE:(0/74) len:3 >> Redirecting number Redirecting number Oct 3 : Type of number = Unknown Numbering plan= Unknown Oct 3a: Presentation = Allowed Screening = Network provided Oct 3b: Reason = Unknown Oct 4 : ******** Number = 17:38:49/ TS D1 BOP FRAME flg=999 [0004] D2 Q921 (S:00 T:000 C/R:1) RR P/F:0 NR:001 17:38:49/ S2 Q921 SL T:000 S:00 DATA-INDICATION 17:38:49/ S3 Q931 SL ID:O,1 C1 TS:01 ESTABLISH-CONFIRM Page 17 of 24

18 Test specification: Test purpose: Test mode: Redirecting Number IE (Information Element) Project No.: TRFTTE The test checks that calls with the Redirecting number information element in the SETUP message are accepted by the EUT. The extraction and processing of the redirecting information element is left to the equipment supplier. This is a subscription option. Compliance Date & Time: 3/17/2010 Verdict: PASS Temperature: 26 C Air Pressure: 99.5 kpa Relative Humidity: 33 % Mains Power Supply: 230Vac 50Hz Remarks: 17:38:49/ TS D1 BOP FRAME flg=012 [0014] D2 Q921 (S:00 T:000 C/R:0) I P:0 NR:001 NS:000 [0010] D3 Q931 Pro:08 Ref:(D,00 01) CALL PROCEEDING IE:(0/18) len:3 >> Channel identification Oct 3 : Int id = implicit Interface = Primary Preferred/Exclusive = Exclusive Channel select = Indication follows Oct 32: Coding = ITU-T Number/Map = Number Type = B-channel Oct 33: Channel number = 1 17:38:49/ RS D1 BOP FRAME flg=298 [0004] D2 Q921 (S:00 T:000 C/R:0) RR P/F:0 NR:001 17:38:51/ S2 Q921 SL T:000 S:00 DATA-INDICATION 17:38:51/ S3 Q931 SL ID:O,1 C1 TS:01 USER-ALERTING 17:38:51/ TS D1 BOP FRAME flg=999 [0009] D2 Q921 (S:00 T:000 C/R:0) I P:0 NR:001 NS:001 [0005] D3 Q931 Pro:08 Ref:(D,00 01) ALERTING 17:38:51/ RS D1 BOP FRAME flg=999 [0004] D2 Q921 (S:00 T:000 C/R:0) RR P/F:0 NR:002 17:38:54/ S2 Q921 SL T:000 S:00 DATA-INDICATION 17:38:54/ S3 Q931 SL ID:O,1 C1 TS:01 CONNECT-INDICATION 17:38:54/ TS D1 BOP FRAME flg=999 [0009] D2 Q921 (S:00 T:000 C/R:0) I P:0 NR:001 NS:002 [0005] D3 Q931 Pro:08 Ref:(D,00 01) CONNECT 17:38:54/ RS D1 BOP FRAME flg=999 [0009] D2 Q921 (S:00 T:000 C/R:1) I P:0 NR:003 NS:001 [0005] D3 Q931 Pro:08 Ref:(O,00 01) CONNECT ACKNOWLEDGE Call connected Page 18 of 24

19 Test specification: Test purpose: Test mode: Date and Time IE (Information Element) The tests check that calls with the Date/Time information element in the SETUP or CONNECT messages are accepted by the EUT. The extraction and processing/display of the date and time information element is left to the equipment supplier. This is a subscription option. Compliance Date & Time: 3/17/2010 Verdict: PASS Temperature: 26 C Air Pressure: 99.5 kpa Relative Humidity: 35 % Mains Power Supply: 230Vac 50Hz Remarks: Call setup with Date and Time 18:34:50/ Q931 ID:O,1 - User Indication (0): Outgoing call #1 Incoming call 18:34:50/ RS D1 BOP FRAME flg=999 [0048] D2 Q921 (S:00 T:000 C/R:1) I P:0 NR:007 NS:006 [0044] D3 Q931 Pro:08 Ref:(O,00 02) SETUP IE:(0/04) len:3 >> Bearer capability Oct 3 : Coding = ITU-T Capability = Speech Oct 4 : Transfer mode = Circuit Transfer rate = 64 kbits/s Oct 5 : L1 protocol = G711 A-law IE:(0/18) len:3 >> Channel identification Oct 3 : Int id = implicit Interface = Primary Preferred/Exclusive = Exclusive Channel select = Indication follows Oct 32: Coding = ITU-T Number/Map = Number Type = B-channel Oct 33: Channel number = 1 IE:(0/29) len:5 >> Date/time Date and Time IE Oct 3 : Year = 10 Oct 4 : Month = 1 Oct 5 : Day = 11 Oct 6 : Hour = 10 Oct 7 : Minute = 34 IE:(0/70) len:5 >> Called party number Oct 3 : Type of number = Unknown Numbering plan= Unknown Oct 4 : ******** Number = 1234 IE:(0/a1) len:0 >> Sending complete IE:(0/76) len:12 >> Redirection number Oct 3 : Type of number = National Numbering plan= ISDN/tel. (E164/E163) Oct 4 : ******** Number = :34:50/ TS D1 BOP FRAME flg=999 [0004] D2 Q921 (S:00 T:000 C/R:1) RR P/F:0 NR:007 18:34:50/ S2 Q921 SL T:000 S:00 DATA-INDICATION 18:34:50/ S3 Q931 SL ID:O,1 C1 TS:01 ESTABLISH-CONFIRM 18:34:50/ TS D1 BOP FRAME flg=009 [0014] D2 Q921 (S:00 T:000 C/R:0) I P:0 NR:007 NS:007 [0010] Page 19 of 24

20 Test specification: Test purpose: Test mode: Date and Time IE (Information Element) The tests check that calls with the Date/Time information element in the SETUP or CONNECT messages are accepted by the EUT. The extraction and processing/display of the date and time information element is left to the equipment supplier. This is a subscription option. Compliance Date & Time: 3/17/2010 Verdict: PASS Temperature: 26 C Air Pressure: 99.5 kpa Relative Humidity: 35 % Mains Power Supply: 230Vac 50Hz Remarks: D3 Q931 Pro:08 Ref:(D,00 02) CALL PROCEEDING IE:(0/18) len:3 >> Channel identification Oct 3 : Int id = implicit Interface = Primary Preferred/Exclusive = Exclusive Channel select = Indication follows Oct 32: Coding = ITU-T Number/Map = Number Type = B-channel Oct 33: Channel number = 1 18:34:50/ RS D1 BOP FRAME flg=292 [0004] D2 Q921 (S:00 T:000 C/R:0) RR P/F:0 NR:008 18:34:51/ S2 Q921 SL T:000 S:00 DATA-INDICATION 18:34:51/ S3 Q931 SL ID:O,1 C1 TS:01 USER-ALERTING 18:34:51/ TS D1 BOP FRAME flg=999 [0009] D2 Q921 (S:00 T:000 C/R:0) I P:0 NR:007 NS:008 [0005] D3 Q931 Pro:08 Ref:(D,00 02) ALERTING 18:34:51/ RS D1 BOP FRAME flg=999 [0004] D2 Q921 (S:00 T:000 C/R:0) RR P/F:0 NR:009 18:34:58/ S2 Q921 SL T:000 S:00 DATA-INDICATION 18:34:58/ S3 Q931 SL ID:O,1 C1 TS:01 CONNECT-INDICATION 18:34:58/ TS D1 BOP FRAME flg=999 [0009] D2 Q921 (S:00 T:000 C/R:0) I P:0 NR:007 NS:009 [0005] D3 Q931 Pro:08 Ref:(D,00 02) CONNECT 18:34:58/ RS D1 BOP FRAME flg=999 [0009] D2 Q921 (S:00 T:000 C/R:1) I P:0 NR:010 NS:007 [0005] D3 Q931 Pro:08 Ref:(O,00 02) CONNECT ACKNOWLEDGE 18:34:58/ TS D1 BOP FRAME flg=045 [0004] D2 Q921 (S:00 T:000 C/R:1) RR P/F:0 NR:008 Call connected Page 20 of 24

21 Test specification: Test purpose: Test mode: Date and Time IE (Information Element) The tests check that calls with the Date/Time information element in the SETUP or CONNECT messages are accepted by the EUT. The extraction and processing/display of the date and time information element is left to the equipment supplier. This is a subscription option. Compliance Date & Time: 3/17/2010 Verdict: PASS Temperature: 26 C Air Pressure: 99.5 kpa Relative Humidity: 35 % Mains Power Supply: 230Vac 50Hz Remarks: Connect message with Date and Time 18:27:37/ TS D1 BOP FRAME flg=999 [0033] D2 Q921 (S:00 T:000 C/R:0) I P:0 NR:003 NS:003 [0029] D3 Q931 Pro:08 Ref:(O,00 01) SETUP IE:(0/04) len:3 >> Bearer capability Oct 3 : Coding = ITU-T Capability = Speech Oct 4 : Transfer mode = Circuit Transfer rate = 64 kbits/s Oct 5 : L1 protocol = G711 A-law IE:(0/18) len:3 >> Channel identification Oct 3 : Int id = implicit Interface = Primary Preferred/Exclusive = Exclusive Channel select = Indication follows Oct 32: Coding = ITU-T Number/Map = Number Type = B-channel Oct 33: Channel number = 31 IE:(0/70) len:11 >> Called party number Oct 3 : Type of number = Unknown Numbering plan= ISDN/tel. (E164/E163) Oct 4 : ******** Number = IE:(0/a1) len:0 >> Sending complete 18:27:37/ RS D1 BOP FRAME flg=999 [0014] D2 Q921 (S:00 T:000 C/R:1) I P:0 NR:004 NS:003 [0010] D3 Q931 Pro:08 Ref:(D,00 01) CALL PROCEEDING IE:(0/18) len:3 >> Channel identification Oct 3 : Int id = implicit Interface = Primary Preferred/Exclusive = Exclusive Channel select = Indication follows Oct 32: Coding = ITU-T Number/Map = Number Type = B-channel Oct 33: Channel number = 31 18:27:37/ TS D1 BOP FRAME flg=079 [0004] D2 Q921 (S:00 T:000 C/R:1) RR P/F:0 NR:004 18:27:38/ S3 Q931 SL ID:I,1 C1 TS:31 CONNECT-INDICATION Called party number: :27:38/ Q931 ID:I,1 - Connect (1): LOOP Outgoing call Page 21 of 24

22 Test specification: Test purpose: Test mode: Date and Time IE (Information Element) The tests check that calls with the Date/Time information element in the SETUP or CONNECT messages are accepted by the EUT. The extraction and processing/display of the date and time information element is left to the equipment supplier. This is a subscription option. Compliance Date & Time: 3/17/2010 Verdict: PASS Temperature: 26 C Air Pressure: 99.5 kpa Relative Humidity: 35 % Mains Power Supply: 230Vac 50Hz Remarks: C1 TS: 31 18:27:38/ RS D1 BOP FRAME flg=999 [0016] D2 Q921 (S:00 T:000 C/R:1) I P:0 NR:004 NS:004 [0012] D3 Q931 Pro:08 Ref:(D,00 01) CONNECT IE:(0/29) len:5 >> Date/time Oct 3 : Year = 1 Oct 4 : Month = 12 Oct 5 : Day = 12 Oct 6 : Hour = 14 Oct 7 : Minute = 45 18:27:38/ TS D1 BOP FRAME flg=999 [0004] D2 Q921 (S:00 T:000 C/R:1) RR P/F:0 NR:005 18:27:38/ S2 Q921 SL T:000 S:00 DATA-INDICATION 18:27:38/ TS D1 BOP FRAME flg=001 [0009] D2 Q921 (S:00 T:000 C/R:0) I P:0 NR:005 NS:004 [0005] D3 Q931 Pro:08 Ref:(O,00 01) CONNECT ACKNOWLEDGE 18:27:38/ RS D1 BOP FRAME flg=278 [0004] D2 Q921 (S:00 T:000 C/R:0) RR P/F:0 NR:005 Connect with Date and time Call connected Page 22 of 24

23 Test specification: Test purpose: Test mode: Project No.: TRFTTE Progress Indicator IE (Information Element) Call not end to end ISDN The test checks that calls from an analogue port result in a SETUP message that includes a Progress Indicator IE Call is not end to end ISDN. Compliance Date & Time: 3/17/2010 Verdict: PASS Temperature: 26 C Air Pressure: 99.5 kpa Relative Humidity: 33 % Mains Power Supply: 230Vac 50Hz Remarks: Analogue port includes Progress Indicator IE 19:50:20/ TS D1 BOP FRAME flg=999 [0053] D2 Q921 (S:00 T:000 C/R:0) I P:0 NR:000 NS:000 [0049] D3 Q931 Pro:08 Ref:(O,00 01) SETUP Outgoing call IE:(0/04) len:3 >> Bearer capability Oct 3 : Coding = ITU-T Capability = Speech Oct 4 : Transfer mode = Circuit Transfer rate = 64 kbits/s Oct 5 : L1 protocol = G711 A-law IE:(0/18) len:3 >> Channel identification Oct 3 : Int id = implicit Interface = Primary Preferred/Exclusive = Exclusive Channel select = Indication follows Oct 32: Coding = ITU-T Number/Map = Number Type = B-channel Oct 33: Channel number = 31 IE:(0/1e) len:2 >> Progress indicator Progress Indicator Oct 3 : Coding = ITU-T Loc = User Oct 4 : = Not end to end ISDN Not end to end IE:(0/28) len:14 >> Display ISDN Oct 3 : ******** IA5 = JONES JENNIFER IE:(0/70) len:11 >> Called party number Oct 3 : Type of number = Unknown Numbering plan= ISDN/tel. (E164/E163) Oct 4 : ******** Number = IE:(0/a1) len:0 >> Sending complete 19:50:20/ RS D1 BOP FRAME flg=999 [0014] D2 Q921 (S:00 T:000 C/R:1) I P:0 NR:001 NS:000 [0010] D3 Q931 Pro:08 Ref:(D,00 01) CALL PROCEEDING IE:(0/18) len:3 >> Channel identification Oct 3 : Int id = implicit Interface = Primary Preferred/Exclusive = Exclusive Channel select = Indication follows Oct 32: Coding = ITU-T Number/Map = Number Type = B-channel Oct 33: Channel number = 31 Page 23 of 24

24 Test specification: Test purpose: Test mode: Project No.: TRFTTE Progress Indicator IE (Information Element) Call not end to end ISDN The test checks that calls from an analogue port result in a SETUP message that includes a Progress Indicator IE Call is not end to end ISDN. Compliance Date & Time: 3/17/2010 Verdict: PASS Temperature: 26 C Air Pressure: 99.5 kpa Relative Humidity: 33 % Mains Power Supply: 230Vac 50Hz Remarks: 19:50:20/ TS D1 BOP FRAME flg=094 [0004] D2 Q921 (S:00 T:000 C/R:1) RR P/F:0 NR:001 19:50:21/ S3 Q931 SL ID:I,1 C1 TS:31 CONNECT-INDICATION Called party number: :50:21/ Q931 ID:I,1 - Connect (1): LOOP C1 TS: 31 19:50:21/ RS D1 BOP FRAME flg=999 [0016] D2 Q921 (S:00 T:000 C/R:1) I P:0 NR:001 NS:001 [0012] D3 Q931 Pro:08 Ref:(D,00 01) CONNECT IE:(0/29) len:5 >> Date/time Oct 3 : Year = 1 Oct 4 : Month = 12 Oct 5 : Day = 12 Oct 6 : Hour = 14 Oct 7 : Minute = 45 19:50:21/ TS D1 BOP FRAME flg=999 [0004] D2 Q921 (S:00 T:000 C/R:1) RR P/F:0 NR:002 19:50:21/ S2 Q921 SL T:000 S:00 DATA-INDICATION 19:50:21/ TS D1 BOP FRAME flg=001 [0009] Call connected D2 Q921 (S:00 T:000 C/R:0) I P:0 NR:002 NS:001 [0005] D3 Q931 Pro:08 Ref:(O,00 01) CONNECT ACKNOWLEDGE 19:50:21/ RS D1 BOP FRAME flg=278 [0004] D2 Q921 (S:00 T:000 C/R:0) RR P/F:0 NR:002 19:50:31/ TS D1 BOP FRAME flg=999 [0004] D2 Q921 (S:00 T:000 C/R:0) RR P/F:1 NR:002 Page 24 of 24