GSV-2MSD-DI DMS-Data Logger

Transcription

1 GS-2MSD-DI DMS-Data Logger Description The GS-2MSD-DI is a measuring amplifier with integrated data logger, which is suitable as a hand-held device and for stationary use. Due to its compact size, the GS-2MSD-DI fits in every bag. Data logger with SD card slot USB interface For DMS quarter, half and full bridges 0...0, potentiometric sensor 24 bit resolution sensor configurations available Battery mode Real-time clock IP version optional The sensors are connected via -pin Sub-D connector. Force sensors, torque sensors, DMS, quarter bridges, half bridges and full bridges can be connected. The measuring amplifier has integrated bridge completition for 20 ohm, 30 ohm and 000 ohm strain gauges. Active sensors with output signal and potentiometric distance sensors can also be connected. A version of the device with protection class IP is also available. The SD card slot and the USB interface are then sealed with an additional cover. The SUB-D sensor connection and the housing seals are then reinforced for this protection class. The measurement data is saved with time stamp. Different operating modes e.g. individual value request, permanent recording, triggering per control line, min./max. mode and other settings are possible. The measuring rate can be set up to 370. Recording on SD card is possible up to 000. Up to sensor configurations can be defined and retrieved, e.g. for switching a sensor or quickly setting the measurement conditions. Tel +49 (0) , Fax +49 (0) , info@me-systeme.de,

2 Dimensions Terminal assignment Sensor terminal, Sub-D Screen 2 GNDA Ground analogue input 7 Tare Zero-setting input / Trigger input 9 UE Analogue input 0 UA Analogue output +US Positive bridge power supply -US Negative bridge power supply (GND) +UD Positive differential input -UD Negative differential input 3 +UF Positive sensor cable 2 -UF Negative sensor cable 4 HB Half Bridge selector QB20 3 QB30 4 QB000 Bridge Completition Resistor 20 ohm Additional quarter bridge 30 ohm Additional quarter bridge 000 ohm Pin 4 must be bridged with Pin to connect half and quarter bridges. Quarter bridge are connected in three-wire connection to Pin, Pin and QB (3 and/or or 4). 9 Table : Allocation Sub-D socket 2 Tel +49 (0) , Fax +49 (0) , info@me-systeme.de,

3 Connection plan for DMS bridges Full bridge Half bridge Quarter bridge -pole Sub D -pole Sub-D -pole Sub-D R R 4 R 4 QB Shield Shield No bridge Bridge between 4 and Bridge between 4 and Table : Connection of full and/or half and quarter bridges to -pin Sub D socket The following are supplied as standard accessories: Switching power supply /.7A -pin Sub-D mating connector USB cable Software CD Instruction manual Required accessories: SD memory card, Class 0 (recommended for recordings of 000) Tel +49 (0) , Fax +49 (0) , info@me-systeme.de, 3

4 Technical data (in battery operation or UB = 2 DC in the nominal temperature range) Size alue Unit Accuracy class Analogue 0, Digital Inputs Measurement range 0,0 ± (JP on with sensor supply) ±2 or ±3. per software (JP on 2 with 2, sensor supply) m/ m/ Connectible full bridge 4 x 30 Bridge supply voltage 2, / Input impedance >20 (300pF) M Common mode rejection DC 00 Analogue input ) Input voltage range >20 > Input resistance k Accuracy Linearity deviation <0,02 of unit Influence of temperature on Measurement range m/: <0.4 type 0.2 of unit the zero point per 0K Measurement range 2m/: <0.2 type 0. of unit Influence of temperature on the measurement sensitivity per 0K referring to the measured value < 0,; type. 0,0 Analogue output <0,0; type. 0,00 Display / digital Resolution Peak value >30000 parts RMS >0000 parts Output Analogue output filter -3dB cut-off frequency, Bessel, 2. order Digital output filter - 3dB cut-off frequency Digital output measuring rate Analogue output Source resistance Control cables 3.; 20; 700 (can be switched using software) High level: 3.4 (active high) Automatic zero-point adjustment Low level: <.4 4 Tel +49 (0) , Fax +49 (0) , info@me-systeme.de, db db

5 Supply Supply voltage Nominal range Operating range Size alue Unit Power input 2 (charge battery: max. ) A Battery 3,2 Wh Operating time with battery Normal operation Standby Duration of battery charging Supply voltage Supply with USB (standby operation) Interface USB version max. 20 max. 300 max. max Fullspeed Device classes Mass Storage Device, Communication Device Class Memory card SD (.x), SDHC File system FAT, FAT32 Functions, user menu (selection) Parameter memory Last setting (automatic) Manufacturer s settings parameter sets Other functions - programmable amplification - programmable adjustment of the digital final value - activation of the zero-point adjustment Temperature range Nominal temperature range 0 +0 Storage temperature range Dimensions L x B x H Weight Protection class x 7 x 0 0 IP / IP ) The analogue input is not switched over to the analogue output. Absolute limit values (all voltages based on supply chassis) Differential input:: Sense inputs: Control cables: Analogue input: Subject to technical modifications. ersion DC DC Days C C mm g Tel +49 (0) , Fax +49 (0) , info@me-systeme.de,