DEMO MANUAL DC1338A LTC2990 I 2 C Temperature Voltage and Current Monitor DESCRIPTION

Transcription

1 DEMO MANUAL DC8A LTC990 I C Temperature Voltage and Current Monitor DESCRIPTION Demonstration circuit 8A features the LTC 990, a high performance temperature, voltage and current monitor that uses I C for communication. It offers submillivolt resolution and % current and C temperature measurement accuracy. DC8A is a member of Linear Technology s QuikEval family of demonstration boards. It is designed to allow easy evaluation of the LTC990 and may be connected directly to the target application s analog signals while using the DC90 USB Serial Controller board and supplied software to measure performance. Exposed ground planes allow proper grounding to prototype circuitry. After evaluating with Linear Technology s software, the I C lines can be connected to the end application s processor/controller for development of the serial interface. Design files for this circuit board are available at L, LT, LTC, LTM, Linear Technology and the Linear logo are registered trademarks and QuikEval is a trademark of Linear Technology Corporation. All other trademarks are the property of their respective owners. INPUTS RIBBON CABLE TO DC90 CONTROLLER Figure. Proper Measurement Equipment Setup. Power Is Obtained from DC90 dc8af

2 DEMO MANUAL DC8A QUICK START PROCEDURE Connect DC8A to a DC90 USB serial controller using the supplied conductor ribbon cable. Connect DC90 to host PC with a standard USB A/B cable. Run the evaluation software supplied with DC90 or downloaded from The correct program will be loaded automatically. Click the COLLECT button to start reading the input voltage (COLLECT button becomes PAUSE after collection has been initiated). Details on software features are documented in the control panel s help menu. Figure. Software Screenshot dc8af

3 DEMO MANUAL DC8A HARDWARE SETUP Connection to DC90 Serial Controller J is the power and digital interface connector. Connect to DC90 serial controller with supplied conductor ribbon cable. Jumper Settings V, V, V, V: These jumpers can be toggled between VOLT and. VOLT connects the corresponding input on the LTC990 with the corresponding turret for an external input. connects the corresponding input to the onboard FMMT90 (V and V) or the FMMT906 (V and V). Please note that the jumpers should be moved in pairs, V and V should both be connected either to VOLT or and V and V should also be both connected to either VOLT or. Once set, the proper selection should also be made inside the QuikEval software in the mode box to reflect any changes made. V CC : EXT allows the LTC990 to be powered from an external supply of.9v to.v, connected to the VCC EXT and GND turrets. If set to INT, the LTC990 is powered by the attached DC90B. ADR0, ADR: These jumpers are used to select the I C address for the LTC990. When used with QuikEval, the correct address should also be selected from within the software. Analog Connections Analog signal connections are made at turrets V, V, V and V. Single-ended input range is 0 to V CC, differential is ±00mV with a common mode range of 0 to V CC. When connecting the board to an existing circuit the exposed ground planes along the edges of the board may be used to form a solid connection between grounds. GND ( locations): This turret is connected directly to the internal ground planes. VCC EXT: This turret allows the user to provide V CC to the LTC990. (.9V to.v) V, V, V, V: These turrets are used to provide input voltage to the monitor when the corresponding jumpers are set to the VOLT position. V + : Unregulated 0V coming from the DC90B. Turret provided for testing purposes only. Presence of 0V indicates proper connection of DC90B. dc8af

4 DEMO MANUAL DC8A PARTS LIST ITEM QUANTITY REFERENCE DESIGNATOR DESCRIPTION MANUFACTURER S PART NUMBER Required Circuit Components: C, C CAP, X7R 0.µF V 0% AVX, 060C0KATA C, C CAP, NPO 70pF V 0% AVX, 060A7KATA 8 E, E, E, E, E, E6, E7, E8 TURRET, TESTPOINT MILL MAX, JP, JP, JP, JP, JP, HEADERS, PINS mm CTRS SAMTEC, TMM-0-0-L-S JP6, JP7 J HEADERS, PIN mm CTRS MOLEX, Q TRANSISTOR, PNP ZETEX, FMMT906 7 Q TRANSISTOR, NPN ZETEX, FMMT90 8 R, R RES, CHIP.99k 0.06W % VISHAY, CRCW00K99FKED 9 U IC,, VOLT, CURR MONITOR LINEAR TECHNOLOGY, LTC990CMS 0 U IC, SERIAL EEPROM MICROCHIP, LC0-I/ST 7 XJP, XJP,XJP, XJP, XJP TO XJP7 SHUNT, mm CTRS SAMTEC, SN-BK-G dc8af

5 DEMO MANUAL DC8A SCHEMATIC DIAGRAM ECO REV REVISION HISTORY DESCRIPTION APPROVED DATE ADR VCC E D EXT VCC D EXT 0 E INT GND JP JP V ADR0 E V+ VOLT J JP C VUNREG 70pF 0 E JP SCL SDA +V V Q TP TP FMMT906 V SCK/SCL C C V SDA 6 VOLT SCL 7 6 JP 7 V E ADR0 8 8 V ADR 9 V V C EESDA 9 VCC 0 EEVCC 0 V GND 0.uF EESCL VOLT EEGND U JP6 Q LC0-I/ST E6 FMMT90 8 V C VCC A0 70pF 7 V WP A R 6 SCL A B B.99K % SDA VSS VOLT R JP7.99K E7 % C V E8 GND 0.uF TECHNOLOGY Leo C. A A Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights. dc8af

6 DEMO MANUAL DC8A DEMONSTRATION BOARD IMPORTANT NOTICE Linear Technology Corporation (LTC) provides the enclosed product(s) under the following AS IS conditions: This demonstration board (DEMO BOARD) kit being sold or provided by Linear Technology is intended for use for ENGINEERING DEVELOPMENT OR EVALUATION PURPOSES ONLY and is not provided by LTC for commercial use. As such, the DEMO BOARD herein may not be complete in terms of required design-, marketing-, and/or manufacturing-related protective considerations, including but not limited to product safety measures typically found in finished commercial goods. As a prototype, this product does not fall within the scope of the European Union directive on electromagnetic compatibility and therefore may or may not meet the technical requirements of the directive, or other regulations. If this evaluation kit does not meet the specifications recited in the DEMO BOARD manual the kit may be returned within 0 days from the date of delivery for a full refund. THE FOREGOING WARRANTY IS THE EXCLUSIVE WARRANTY MADE BY THE SELLER TO BUYER AND IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED, IMPLIED, OR STATUTORY, INCLUDING ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE. EXCEPT TO THE EXTENT OF THIS INDEMNITY, NEITHER PARTY SHALL BE LIABLE TO THE OTHER FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES. The user assumes all responsibility and liability for proper and safe handling of the goods. Further, the user releases LTC from all claims arising from the handling or use of the goods. Due to the open construction of the product, it is the user s responsibility to take any and all appropriate precautions with regard to electrostatic discharge. Also be aware that the products herein may not be regulatory compliant or agency certified (FCC, UL, CE, etc.). No License is granted under any patent right or other intellectual property whatsoever. LTC assumes no liability for applications assistance, customer product design, software performance, or infringement of patents or any other intellectual property rights of any kind. LTC currently services a variety of customers for products around the world, and therefore this transaction is not exclusive. Please read the DEMO BOARD manual prior to handling the product. Persons handling this product must have electronics training and observe good laboratory practice standards. Common sense is encouraged. This notice contains important safety information about temperatures and voltages. For further safety concerns, please contact a LTC application engineer. Mailing Address: Linear Technology 60 McCarthy Blvd. Milpitas, CA 90 Copyright 00, Linear Technology Corporation 6 LT 0 PRINTED IN USA Linear Technology Corporation 60 McCarthy Blvd., Milpitas, CA (08) -900 FAX: (08) LINEAR TECHNOLOGY CORPORATION 00 dc8af