SATEL-LP product family

Transcription

1 SATEL-LP product family V1.6

2 SATEL LP -radio units SATEL-LP24 License free 2.4 GHz ( GHz GHz) ISM (Industrial, Scientific and Medical) band, FHSS (Frequency Hopping Spread Spectrum) Wireless transceiver with RS-232 and RS-485 interface. Can be extended with I/O modules (max. 32 extension modules per radio unit). Screw connection, antenna connection: RSMA (female), including DIN rail connector. Max. TX power 20dBm(100mW) -40 C C (>55 C derating) Universal use 128-bit data encryption (AES) Mesh networks of up to Mission-Critical 250 devices Connectivity Air speed: Data transmission speed [kbps] Typical receiver sensitivity [dbm] EIRP: max. radiated power [dbm] Potential distance that can be covered with line of sight and a system reserve of 12 db [m] (Europe: 19) 125 (default) (Europe: 18, default) (Europe: 11) (Europe: 2000) 5000 (Europe: 3000)

3 SATEL LP -radio units SATEL-LP9 900 MHz ( MHz) ISM (Industrial, Scientific and Medical) band (FHSS, Frequency Hopping Spread Spectrum) Wireless transceiver with RS-232 and RS-485 interface. Can be extended with I/O modules (max. 32 extension modules per radio unit). Screw connection, antenna connection: RSMA (female), including DIN rail connector. Max. TX power 30dBm(1000mW) For use in North and South America and Canada 128-bit data encryption (AES) -40 C C (>55 C derating) Mesh networks of up to 250 devices Cooling part Air speed: Data trans- mission speed [kbps] Typical receiver sensitivity [dbm] (default) D9, RS232 combination socket with the screw terminal block

4 SATEL-LP8 868 MHz (869.4 MHz MHz) FHSS (Frequency Hopping Spread Spectrum)* Wireless transceiver with RS-232 and RS-485 interface. Can be extended with I/O modules (max. 32 extension modules per radio unit). Screw connection, antenna connection: RSMA (female), including DIN rail connector Max. TX power 27dBm(500mW) 128-bit data encryption (AES) -40 C C (>55 C derating) For use throughout Europe Mesh networks of up to 99 devices Air speed: Data trans- mission speed Typical Mission-Critical receiver Connectivity [kbps] sensitivity [dbm] SATEL LP -radio units (default) MHz 2,4 GHz *Depending of network topology and selected air speed. The FHSS is depending of the used topology and baud rate over the air. Only in Mesh networks with baud rates from 1,2k up to 19,2k the FHSS is used. But at 60k and 120k the frequency is fixed. In pointto-point connections, FHSS is never used.

5 SATEL LP -extension modules SATEL-LP-DI4 YI digital inputs (0 250 V AC/DC) SATEL-LP-DOR4 YI digital relay outputs (6 A, 24 VDC / 250 VAC) SATEL-LP-AI4 YI analog inputs ( ma / 4 20 ma) SATEL-LP-AO4 YI analog outputs (0 20 ma / 4 20 ma, 0 10 VDC) SATEL-LP-DI8 YI digital inputs ( VDC) OR 2 pulse inputs (0 100 Hz) SATEL-LP-DO8 YI digital transistor outputs (30.5 VDC / 200 ma) SATEL-LP-DAIO6 YI analog input (0 20 ma / 4 20 ma) 1 analog output (0 20 ma / 4 20 ma, 0 10 VDC) 2 digital input / outputs (2A, 24 VDC / 250 VAC) SATEL-LP-PT100 YI PT 100 resistance thermometer inputs (-50 C +250 C) 99 I/O extension modules per radio network.

6 99 I/O extension modules per radio network. SATEL LP -extension modules The input /output modules that can work against each other Input module SATEL-LP-DI4 YI digital inputs (0 250 V AC/DC) SATEL-LP-DOR4 YI digital relay outputs (6 A, 24 VDC / 250 VAC) SATEL-LP-AI4 YI analog inputs ( ma / 4 20 ma) SATEL-LP-AO4 YI analog outputs (0 20 ma / 4 20mA, 0 10 VDC) Output module Possible to set input point to multipoint output (one per radio module) SATEL-LP-PT100 YI PT 100 resistance thermometer inputs (-50 C +250 C) The pulse counter function is only available in PLC/Modbus RTU mode. SATEL-LP-DAIO6 YI analog input (0 20 ma / 4 20 ma) 1 analog output (0 20 ma / 4 20 ma, 0 10 VDC) 2 digital input / outputs (relay) (0 250 V AC/DC) Only point-to-point in I/O data mode SATEL-LP-DI8 YI digital inputs ( VDC) OR 2 pulse inputs (0 100 Hz) SATEL-LP-DO8 YI digital transistor outputs (30.5 VDC / 200 ma)

7 SATEL LP -extension modules Digital-Input SATEL-LP-DI4 YI0101 Analog-Input SATEL-LP-AI4 YI0103 Digital/Analog- In-/Output SATEL-LP-DAIO6 YI0105 Resistance thermometer inputs SATEL-LP-PT100 YI0108 Digital-Input SATEL-LP-DI8 YI0106 Analog-Output SATEL-LP-AO4 YI0104 Digital-Output SATEL-LP-DI8 YI0107 Digital-Output(relay) SATEL-LP-DOR4 YI0102 Analog-Output SATEL-LP-AO4 YI0104 Digital/Analog-In- /Output SATEL-LP-DAIO6 YI0105 The pulse counter function is only available in PLC/Modbus RTU mode.

8 SATEL LP -radio unit SATEL-LP24 24 V DC Power suply RSMA- antenna connector RSSI test port (0 3 V) T-BUS connector connection Programming interface (S-Port) Diagostic + Configuration Status LEDs (ERR, DAT, PWR) Metal foot catch for DIN rail fixing Yellow Thumb Wheel for RAD-ID LED-Bar graph RSSI SET push button Status LED (RX/TX) Serial Interface RF Link relay (potential free) Terminal block RS-232 Terminal block RS-485

9 SATEL LP module installation Mount the wireless module to the left and the I/O extension modules exclusively to the right of the wireless module. The individual extension modules can be arranged in any order. Data is transmitted and power is supplied to the I/O extension modules via the T-BUS foot. For easy installation, it is also possible to pull out the screw terminal block from the device and to re-insert it after having connected the wires.

10 SATEL LP -extension units DIP switches for configuring the output behavior of the relay outputs (hold/reset) SATEL-LP-DOR4 Relay output 1 with floating PDT contact White thumbwheel for setting the I/O- MAP address PWR status LED, green (supply voltage) Relay output 2 with floating PDT contact T-BUS connector connection DAT status LED, green (bus communication) ERR status LED, red (communication error) Metal foot catch for DIN rail fixing Status LEDs for the relay outputs DO1... DO4 Relay output 4 with floating PDT contact Relay output 3 with floating PDT contact

11 SATEL LP -product family SATEL-LP24 connection notes: Included in the package of the selected device: o T-BUS connector o Package slip o In same sheet in English, German, Italian, in French, Spanish, Portuguese, Russian, Turkish and Chinese. o Safety notes o Short description o Connection notes o Configuration o Diagnostic and status indicators o Technical data SATEL-LP-DI4 connection notes: Connection notes pictured on the left side of the modules. SATEL-LP-DOR4 connection notes:

12 SATEL-PL24 default settings: o Operating mode: I/O data (wire in/wire out) SATEL LP -product family Default settings of the radio units Wireless interface o Net ID: 127 o RF band: 4 RF bands between and network IDs between by using the SATEL-LP-CONF software o Encryption: OFF o Network structure: Mesh o Device type: Repeater/slave o Blacklisting WLAN channel: 6 (2437MHz (+/-11MHz)) o Data rate of the wireless interface: 125 kbps o Receive preamplifier: Activated o Transmission power: 18dBm(~63mW) SATEL-LP8 default settings: o Operating mode: I/O data mode (wire in/wire out) Wireless interface o Net ID: 127 o RF band: 2 RF bands between and network IDs between by using the SATEL-LP-CONF software o Encryption: OFF o Network structure: Mesh o Device type: Repeater/slave o Data rate of the wireless interface: 9.6 kbps o Reception amplifier: Activated o Transmission power: 27dBm(500mW)

13 SATEL LP -product family Default settings of the radio units SATEL-LP9 default settings: o Operating mode: I/O data (wire in/wire out) Wireless interface o Net ID: 127 o RF band: 1 RF band 1 always in use. Network IDs between by using the SATEL-LP-CONF software o Encryption: OFF o Network structure: Star o Device type: Slave o Data rate of Mission-Critical the wireless interface: Connectivity 125kbps o Transmission power: 30dBm (1W)

14 SATEL LP -product family I/O to I/O Operation modes o I/O from one location to another via wireless without the need for an additional controller or software. PLC/Modbus RTU mode o Digital/analog I/O signals are linked to a controller (Modbus RTU) o I/O extension modules are connected to the controller directly via the integrated RS- interface by means of wireless communication. The wireless master works as a Modbus slave and has its own Modbus address. o Configuration via SATEL-LP-CONF software Serial to serial o o o o In serial data mode, multiple controllers or serial I/O devices are networked. Configuration with PC software. In serial communication mode, the messages are realised via broadcast transmission(note! Only from master radio!). Replacement of RS-232/485 cables Configuration via SATEL-LP-CONF software

15 SATEL LP -product family Network structures o All the communication methods, I/O to I/O, serial communication and PLC/Modbus RTU mode can be used with any network structure. o Only one operating mode can be set in use at once. It is not possible to simultaneously transmit I/O signals and serial data (future development). o It is not possible to individually assign the channels of the input and output modules(input 1 of an input module no.:x output 1 of an output module no.:x). Network structures: Mesh and line networks Star networks Point-to-point networks

16

17 OTA data 2,4 GHz 250 kbps up to 800 m Requirement 1. Free lign of sight 2. Antenna Panel Omni 3. Fresnel Zone 125 kbps(factory default) up to 1500 m up to 5000 m 16 kbps

18 2,4GHz antenna setups 2 dbi Omni 6dBi Omni 8 dbi Panel 19 dbi Parabol typ. > 5000 m typ. up to 300 m typ. up to 1500 m typ. up to 3000 m The range can be considerably exceeded or fallen below and depends on the environment, OTA data rate and antenna technology!

19 OTA data 869 MHz 120 kbps up to 5 km 60 kbps Requirement 1. Free lign of sight 2. Antenna Panel Omni 3. Fresnel Zone up to 10 km 19,2 kbps up to 15 km 9,6 kbps (factory default) up to 20 km 1,2 kbps up to 25 km

20 869MHz antenna setups 4dBi Omni 3,5 dbi Panel 8 dbi Yagi 12 dbi Yagi typ. up to 8 km typ. up to 10 km typ. up to 15 km typ. > 20 km The range can be considerably exceeded or fallen below and depends on the environment, OTA data rate and antenna technology!

21

22 Accessories Omnidirectional antennas: (Incl. Wall mounting bracket and mast clips) SATEL-LP-ANT24N, 6dBi, N(f) YA2400 SATEL-LP-ANT9N, 7dBi, N(f) YA1900 SATEL-LP-ANT8N, 4dBi, N(f) YA0869 Radio antenna connection: RSMA(f) Antenna cable: SATEL-LP-RF2, YC1520 RSMA(m) N(m), 2 meters Atte.: 0,87dB@868/900, 1,35dB@2,4GHz

23 Omnidirectional antennas: (Incl. Wall mounting bracket and mast clips) SATEL-LP-ANT24N, 6dBi, N(f) YA2400 SATEL-LP-ANT9N, 7dBi, N(f) YA1900 SATEL-LP-ANT8N, 4dBi, N(f) YA0869 Antenna cable: ECOFLEX10 Low loss cable YC1004 N(m) to N(m) connectors YC1003 ECOFLEX15 Low loss cable N(m) to N(m) connectors Radio antenna connection: RSMA(f) Accessories YC1005 YC1007 Cable type Ecoflex 10 Frequency [MHz] Max. lenght meters feet 15 8 Attenuation [db/10 m) Attenuation [db/10 ft) 1,34 0,41 2,36 0, ,92 0,28 Ecoflex ,63 0,50 Recommended max. lenght Adapter cable YC1550 SATEL-LP-RF50 control cabinet feed-through, N(f) - RSMA(m) length: 0.5 m Atten.: 0,6dB@868/900, 1dB@2,4GHz 49 26

24 Accessories SATEL-LP-MEMORY YO0010 For all radio SATEL-LP radio modules SATEL-LP-PROG YC0520 For programming and diagnostics of SATEL-LP radio modules SATEL-LP-CONF3 For SATEL-LP24 SATEL-LP-CONF5 For SATEL-LP24 SATEL-LP-CONF7 For SATEL-LP24 YO0003 YO0005 YO0007 SATEL-LP-ANT8/9 YA0899 For SATEL-LP8 and SATEL-LP9 RSMA (m) 2dBi SATEL-LP-ANT24 YA2410 For SATEL-LP24 RSMA (m) 2dBi SATEL-LP8-CONF1 For SATEL-LP8 SATEL-LP9-CONF1 For SATEL-LP9 YO0001 YO0002 Power supply YP0118 PS-DIN-2, DIN-rail, IN Vac, OUT 24 Vdc / 2.5 A

25 Thank you for your attention