TableofContents. Important Information: Warning: Please read operating manual carefully before operation.

Size: px

Start display at page:

Download "TableofContents. Important Information: Warning: Please read operating manual carefully before operation."

Anis Jacobs
5 years ago
Views:

1 Important Information: Please read operating manual carefully before operation. Warning: Overpush or overdraw the syringe may result in the fluid sprayed. Use appropriate measures to protect operator and equipment. Be careful during operation. When the fluid sprays out on the drive unit please shut down the power supply immediately and clean the drive unit, then turn on the power supply. If a trouble happens please contact us or our dealer. Don't repair the equipment by yourself. Be careful when inserting or extracting the connection wire between controller and drive unit to prevent the plug from damaging. If the power line or the plug are worn or damaged please pull out the plug. Please shut down the power supply before connecting the external control equipment. TableofContents Introduction Operation Panel Basic Operation Start/Stop Key Fast Forward Key Fast Reverse Key Rotary Coded Switch Channels Switch Key Menu Frame Work Multichannel Running Interface Multichannel Functions Setting Drive Unit Copy Parameters Set Delay Time Controller I.D. Single Channel Running Interface Single Channel Functions Setting Working ion meters Setting Acceptable Drive Units and Syringes Syringe Loading External Control Function Maintenance Warranty Technical Specifications

2 Introduction TS series products are controllers of four channels and multifunction syringe pumps. They need to be connected with drive units to constitute syringe pump systems of strong functions and easytooperate. They are widely used in biological laboratory. There are 3 types: Controller Type TSA TSA TSB DriveUnitType L007A L007A W009B Working Mode Infusiononly Infusion/Withdrawal Infusion/Withdrawal Operation Panel Fast Forward Key Channels Switch Key Fast Reverse Key Start/Stop Key Rotary Coded Switch S S3 S S Controller S Drive Unit S3 Glass Syringe F5 F F Power Switch F F4 F Power Socket F3 F3DriveUnitSocket F4 External Control Input and Communication Interface F5 External Control Output Interface Controller and drive unit are connected through 8 pin S terminal. Be careful when insertion or extraction. Please see page for detail information about External control function. Basic Operation Start/Stop Key Start/Stop Key to start or stop the pump. In multichannel working mode, to pause the running state, the pump will prompt if continue the current working state. Fast Forward Key In multichannel working mode, pressing the Fast Forward Key all the enabling channels infuse at the max. speed. In single channel working mode, pressing the Fast Forward Key this channel infuses at the max. speed. Loose this key the pump stops. Other keys are invalid when pressing this key. Fast Reverse Key In multichannel working mode, pressing the Fast Reverse Key all the enabling channels withdraw at the max. speed. In single channel working mode, pressing the Fast Reverse Key this channel withdraws at the max. speed. Loose this key the pump stops. Other keys are invalid when pressing this key. Fast Forward Key and Fast Reverse Key are invalid when the pump is in running state. Rotary Coded Switch () Turn the Rotary Coded Switch for menu selection or parameter setting. Rotary Coded Switch for confirmation. Put the finger in the center of the switch to press the. Put the finger on the small concave which is on the side of the switch to. Channels Switch Key Switch between different channels. Cancel current operation and return to previous menu.

3 Menu Frame Work Multichannel Running Interface #: #: 3#: 4#: Unit: # # 3# 4# # # 3# 4# Delay time: # 6.0 sec # 0.0 sec 3# 0.0 sec 4# 0.0 sec Controller ID: # nl/sec 0.0 sec Syringe: 00μL #V ol: 360 μl 40 sec 5 Syringe: 500μL 3# Vol: 860 μl 68.3 sec 0 Syringe: 000μL Infusion Withdrawal I/W W/I Continuous Unimetrics Becton Dickinson Hamilton Barrel I.D. Disp Vol Unit μL Infusion Unit 8.5 sec Withdrawal Unit 7.0 sec Copy No.: 0 Pause Time: 0. min Vol: 50.00μL Time: 60sec Act: 50.00μL Yes No Cancel Switch on the pump. First initializing, and then display the running interface. #: #: 3#: 4#: a b #: #: 3#: 4#: a. Enabling symbol: Symbol of enabling or disabling the channels. Means enabling the current channel. means disabling the current channel. The disabling channel is invalid when the pump is in running state or switching the channels. b. Channel number: Channel serial number. c. Start/Stop state: Display the state of current channel. Start displays. Stop displays. Pause displays. d. Direction: Display running direction. Infusion displays. Withdrawal displays. e. Working mode: Display current working mode. Display in infusion, withdrawal, infusion/withdrawal, withdrawal/infusion modes. Display in continuous mode. Multichannel Functions Setting Drive Unit: Means enabling the current channel. Means disabling the current channel. The disabling channel will not work when the pump is working. The setting method is as below: Unit: # # 3# 4# # # 3# 4# Yes or No e d c Unit: # # 3# 4# # # 3# 4# to set the enabling channels Turn the 4# Vol:700 nl 5 sec Syringe: 0μL : Volume Speed Flow Unit: # # 3# 4# # # 3# 4# Turn the to select the channels 3 4

4 Copy Parameters the parameters of one drive unit as copy parameters, all enabling channels will run according to copy parameters. Not setting copy parameters each enabling channel will run according to its own parameters setting. Means copy channel; means noncopy channel. Only one channel can be selected as copy channel, or noncopy channel is acceptable. The setting method is as below: #: #: 3#: 4#: Set Delay Time #: #: 3#: 4#: Unit: Unit: # # 3# 4# # # 3# 4# # # 3# 4# # # 3# 4# Yes the copy channel or No Turn the Unit: # # 3# 4# # # 3# 4# Delay time: # : 6.0 min # : 0.0 sec 3# : 0.0 sec 4# : 0.0 sec 5 Turn the Yes or No Unit: # # 3# 4# # # 3# 4# to set the copy channel Set delay time to start each drive unit in turn. Time units are sec, min and hour. Time numerical value is from 0. to The setting method is as below: if save the change Turn the to set the delay time Delay time: # : 6.0 sec # : 0.0 sec 3# : 0.0 sec Delay time: # : 6.0 sec # : 0.0 sec 3# : 0.0 sec channel Delay time: # : 6.0 min # : 0.0 sec 3# : 0.0 sec 4# : 0.0 sec Turn the to set the time unit Controller I.D. When control computer controls many pumps through RS485 interface, it must identify each controller's I.D.. This controller I.D. should be unique. It's the identification of this controller. The controller address serial number is from to 30. The default is. The setting method is as below: #: #: 3#: 4#: #: #: 3#: 4#: Single Channel Running Interface Unit: # # 3# 4# # # 3# 4# 6 Controller ID: Turn the Yes or No # Vol:.860 μl 8.3 sec 0 Syringe: 00μL Controller ID: Turn the to set the controller I.D. Switch on the pump. First initializing, and then display the multichannel running interface. Press Channels Switch Key to enter single channel running interface. Please see below for detail operation: Press Channels Switch Key Press Channels Switch Key # Vol:.860 μl 8.3 sec 0 Syringe: 00μL Press Channels Switch Key 3# Vol:.860 μl 8.3 sec 0 Syringe: 00μL Press Channels Switch Key 4# Vol:.860 μl 8.3 sec 0 Syringe: 00μL

5 Three Display Modes for Single Channel Running Interface: Volume Display a. b. c. d. Speed Display # Vol:.860 μl 8.3 sec 0 Syringe: 00μL e. f. g. Single Channel Functions Setting 5 functions are set: # Vol:.860 μl 8.3 sec 0 Syringe: 00μL Please see page 6 Display for Speed and Turn the Flow Rate Display #: 6.75mm/min 8.3 sec 0 Syringe: 00μL #: 4.0nL/sec 8.3 sec 0 Syringe: 00μL a.display mode: Display the current volume, flow rates or speed. Please see page 6 for setting method. b.time: Required time for one time infusing or withdrawal. Counting down when running. c.syringe: Display selected syringe. d.start/stop state: Start displays ; Stop displays ; Pause displays. e.copy number: Display dispensing copy number. Counting down when running (no display in continuous mode). f. Working mode: Display current working mode. Display in infusion, withdrawal, infusion/withdrawal, withdrawal/infusion modes. Display in continuous mode. g.direction: Display running direction. Infusion displays. Withdrawal displays. 7 TSA controller disables. It only has infusion working mode. Working ion # Vol:.860 μl 8.3 sec 0 Syringe: 00μL Please see page 6 Display for Speed and Yes to save the No not to save to return Prompts working mode Yes or No 8 Infusion Withdrawal I/W W/I Turn the to select working mode Continuous Turn the Turn the to select working mode Infusion: The pump infuses during the whole working course Withdrawal: The pump withdraws during the whole working course Infusion/Withdrawal: The pump infuses first and then withdraws during the whole working course Withdrawal/Infusion: The pump withdraws first and then infuses during the whole working course Continuous: The pump infuses first and then withdraws, and then cycles continuously Please see page Dispensing Parameters Setting to set the parameters for above working modes.

6 Standard Syringe # Vol:.860 μl 8.3 sec 0 Syringe: 00μL Please see page 6 Display for Speed and the specification Three syringe manufacturers are listed in the TSA,TSA menu. Please see below table for specifications: Unimetrics Yes to save the No not to save to return Unimetrics Hamilton SGE Spec( μl) I.D. ( mm) Spec( cc) I.D. ( mm) I.D. ( mm) Turn the to highlight Yes or No Size ( μl) I.D. :.3mm Unimetrics Becton Dickinson Hamilton Barrel I.D. the type Three syringe manufacturers are listed in the TSB menu. Please see below table for specifications: Becton Dickinson Hamilton Spec( μl) I.D. ( mm) Spec( ml) Spec( μl) I.D. ( mm) Spec( μl) I.D. ( mm) Setting and the Inner Diameter of the Syringe. Setting the Inner Diameter of the Syringe If the syringe used is not listed in the menu the inner diameter of the syringe needs to be measured and entered (0.0 mm 40 mm). The pump can save 4 inner diameters of the syringes. # Vol:.860 μl 8.3 sec 0 Syringe: 00μL Please see page 6 Display for Speed and # : 8.00mm # : 0.00mm 3# : 0.00mm 4# : 0.00mm Yes # : 8.00mm # : 5.00mm 3# : 0.00mm 4# : 0.00mm Yes to save the No not to save to return No # : 0.00mm # : 0.00mm 3# : 0.00mm 4# : 0.00mm # : 8.00mm # : 0.00mm 3# : 0.00mm 4# : 0.00mm. the Inner Diameter of the Syringe the inner diameter of the syringe after setting the inner diameter. Turn the to highlight the Turn the to set the inner diameter Unimetrics Becton Dickinson Hamilton Barrel I.D. 0 Yes or No Yes or No Unimetrics Becton Dickinson Hamilton Barrel I.D.

7 meters Setting The dispense parameters include dispense volume, infusion time, withdrawal time, copy number and pause time. Dispense volume: It is the volume for one time infusion or withdrawal The volume range is nl to ml There are volume units of nl, 0.0nL, 0.μL, μl and 0.0mL available. # Vol:.860 μl 8.3 sec 0 Syringe: 00μL Please see page 6 Display for Speed and Yes to save the No not to save to return Turn the and highlight the Yes or No Disp Vol Unit μL Infusion Unit 8.5 sec Disp Vol Unit μL Infusion Unit 8.5 sec Turn the and set the unit Disp Vol Unit μL Infusion Unit 8.5 sec Turn the to set the volume When the one time dispensing volume or the total dispensing volume (multiply one time dispensing volume by copy number) are more than the volume of the syringe the running interface will display Vol Overflow (see below). Please change the syringe or adjust the dispensing volume or the copy number. Vol overflow! 8.3 sec 0 Syringe: 00μL Infusion time: It is the time for one time infusion The range of infusion time is from 0. second to hours There are time units of second, minute and hour available # Vol:.860 μl 8.3 sec 0 Syringe: 00μL Please see page 6 Display for Speed and Yes to save the No not to save to return Turn the and highlight the Yes or No When the pump can't infuse volume in time the running interface will display Ispeed Overflow (see below). Pleaseadjustthedispensingtimeorthedispensingvolume. Ispeed Overflow! 8.3 sec 0 Syringe: 00μL Disp Vol Unit μL Infusion Unit 8.5 sec Disp Vol Unit μL Infusion Unit 8.5 sec Turn the and set the unit Disp Vol Unit μL Infusion Unit 8.5 sec Turnthe tosetthetime

8 Withdrawaltime:Itisthetimeforonetimewithdrawal The range of withdrawal time is from 0. second to hours There are time units of second, minute and hour available # Vol:.860 μl 8.3 sec 0 Syringe: 00μL Please see page 6 Display for Speed and Yes to save the No not to save to return Turn the and highlight the Yes or No Wspeed Overflow! 8.3 sec 0 Syringe: 00μL Withdrawal Unit 8.3 sec Copy No.: Withdrawal Unit 8.3 sec Copy No.: Turn the and set the unit Withdrawal Unit 8.3 sec Copy No.: Turnthe tosetthetime When the pump can't withdrawal volume in time the running interface will display Wspeed Overflow (see below). Please adjust the dispensing time or the dispensing volume. Copy Number: It is the total infusion and withdrawal numbers of the whole working course. The range is 999. In Infusion/Withdrawal (I/W) and Withdrawal/Infusion (W/I) modes, one time working course is finishing one time infusion and withdrawal. # Vol:.860 μl 8.3 sec 0 Syringe: 00μL Please see page 6 Display for Speed and # Vol:.860 μl 8.3 sec 0 Syringe: 00μL Yes to save the Yes to save the No not to save to return 3 4 Vol overflow! 8.3 sec 0 Syringe: 00μL Pause Time: 0. min Pause Time: No not to save Withdrawal Unit 60.0 sec to return Copy No.: Turn the and set the copy number When the one time dispensing volume or the total dispensing volume (multiply one time dispensing volume by copy number) are more than the volume of the syringe the running interface will display Vol Overflow (see right). Please change the syringe or adjust the dispensing volume or the copy number. Turn the and highlight the DispensePara Yes or No Yes or No Pause Time: It is the stop time between two dispensing operation. Therangeis min. Please see page 6 Display for Speed and Turn the and highlight the DispensePara Withdrawal Unit 60.0 sec Copy No.: 0. min Turn the and set the pause time

9 When the accuracy of the dispensing volume can not reach 0.5% (in the condition of 30% of max. infusion distance), calibration is needed to adjust the linear speed of the drive unit. 8.3 sec 0 # Vol:.860 μl Syringe: 00μL 8.3 sec 0 Syringe: 00μL Please see page 6 Display for Speed and Turn the and highlight the Yes or No Interface A 0% 50% 80% Vol: Time: 60sec Act: 0.00μL Vol: 0.00μL Time: 60sec Act: 0.00μL Start/Stop Key to start the test # Vol:.860 μl Please see page 6 Display for Speed and Yes to save the No not to save to return : Volume Speed Flow Turn the and highlight the Display Mode the Display Mode Yes or No Yes to save the No not to save to return Turn the to enter the calibration volume Yes or No Vol: 0.00μL Time: 60sec Act: 0.00μL Vol: 0.00μL Time: 60sec Act: 0.00μL Turn the to enter the actual volume There are volume, speed and flow rate display modes available. Volume: Display current one time infusion or withdrawal volume Speed: Display current running speed Flow rates (Flow): Display current flow rates Volume (Vol): The required volume for calibration Enter volume setting interface (see Interface A) and to set the calibration volume. There are 0%, 50% and 80% of the syringe volume available. When selecting the userdefined syringe the default calibration volume is 50% of the syringe volume. Please see page 9 to select suitable syringe. Time: The calibration time for the pump is minute. Actual volume (Act): Start/Stop Key after setting the calibration volume. Enter the actual volume. 5 6

10 Acceptable Drive Units and Syringes TSB/W009B TSA/L007A TSA/L007A Drive Unit Glass Syringe Drive Unit Glass Syringe Controller Controller Reference Flow Rates List Syringe Material Glass Syringe Specification ( μl) Glass Syringe Inner Diameter (mm) Flow Rate (/min) Glass Syringe nL 3.30nL 3.8μL 33.0μL 6.60nL 66.0μL 3.8nL 3.8μL 3.96nL 39.6μL 66.nL 66.μL 3.4nL 34.μL Syringe Material Syringe Specification ( μl) Flow Rate (/min) Syringe Material Syringe Specification ( cc) Flow Rate (/min) Syringe Material Syringe Specification ( ml) Flow Rate (/min) Glass Syringe nL 3.30nL 3.8μL 33.0μL 6.60nL 66.0μL 3.8nL 3.8μL 3.96nL 39.6μL Plastic Syringe 66.nL 66.μL 0.38μL 0.460μL 0.896μL.306μL.6μL.904μL.38mL 4.60mL 8.96mL 3.06mL.6mL 9.04mL Plastic Syringe 3.4nL 34.μL μL 0.330μL 0.66μL.33μL 3.305μL 6.60μL.3mL 3.30mL 6.6mL 3.3mL 33.05mL 66.0mL μl ml 7 8

11 Syringe Loading TSB/W009B TSA/L007A Pressing Knob Plunger Fixing Board. Lift up and rotate the pressing knob Barrel Fixing Board.Rotate the tightening knobs according to the arrowhead directions. Loose the plunger fixing board and the barrel fixing board Loading Pole. 3. Lift up the pressing knob and rotate the press knob according to the arrowhead direction to fix the glass syringe See above drawing to load the glass syringe Pressing Knob.Lift up the pressing knob and rotate the pressing knob according to the arrowhead direction. Load the syringe. Rotate the pressing knob to press the syringe TSA/L007A. Lift up and rotate the pressing knob. Rotate and loose the tightening knobs according to the arrowhead directions Pressing Knob Loading Pole. See above drawing to load the glass syringe. Lift up the press knob and rotate the press knob according to the arrowhead direction to press the glass syringe Tightening Knob 3.Tighten the tightening knobs according to the arrowhead directions to fix the syringe 3. Rotate the tightening knobs according to the arrowhead directions to fix the glass syringe Tightening Knob 9 0

12 External Control Function External Control Output Interface Start/Stop State Output Direction State Output Maintenance Keep the surface of the pump clean and dry. Prevent the liquids from entering the inner of the drive units. The surface of drive units are not organic solvent and aggressive liquids resistant. Please pay attention when using. Note If a trouble happens, please contact us or our dealers. Warranty Channel 3 4 Channel Channel 3 Channel Stop State: OC gate is open ( )(5 6)(9 0)(3 4) Running State: OC gate is close are 4 suits OC gates Infusion: OC gate is open Withdrawal:OCgateisclose (3 4)(7 8)( )(5 6) are 4 suits OC gates External Control Input and Communication Interface Port Definition: # +5V # COM 3# COM for external control start/stop 4# External control start/stop: change to high level, start and stop states switch 5# NC 6# COM for Rs485 7# RS485 B 8# RS485 A 3# are RS485 communication bus ports. Can connect to the control computer (computer, PLC, SCM). The warranty period for this product is one year. If repair or adjustment is necessary within the warranty period, the problem will be corrected at no charge if it is not due to misuse or abuse on your part, as determined by the manufacturer. Repair costs outside the warranty period, or those resulting from product misuse or abuse,maybeinvoicedtoyou. TSA/L007A TSA/L007A TSB/W009B Technical Specifications System Functions Parameters Setting: The parameters of each channel can be different Parameters Saving: The parameters of each channel can be saved Running Control: Each drive unit can be controlled separately; Or four drive units can be controlled to run simultaneously or run at different time Copy Channel: All drive units can be run according to the parameters of one drive unit of them Delaying Startup: Delaying startup time of each channel can be controlled separately Memory Function: resume operation or remain stopped when power returns after an interruption Block Protection: When one drive unit stops accidently, the system will warm and stop External Control: Each channel has two ways OC gate output to indicate the start/stop and running direction of this channel Communication: Realize computer control through RS485 communication interface Main Functions for Each Channel ion: The syringe can be selected in the manufacturer table which includes manufacturer and size Userdefined Syringe: 4 inner diameter of userdefined syringe barrel canbeinputandsaved Working Mode Setting: TSA has only infusion working mode. TS A/TSB has 5 working modes available: infusion, withdrawal, infusion/withdrawal, withdrawal/infusion, continuous Parameters Setting: Set dispensing volume, infusion time, withdrawal time, pause time and copy number Display ion: Different parameters (volume, flow rate, linear speed) can be selected in the main display interface FastForward&FastReverse:Infusionorwithdrawalatthemax.speed : Acquire accurate volume through calibration

13 TSA/L007A, TSA/L007A Specifications Max. Infusion Distance: 70 mm AcceptableGlassSyringe:5μL000μL Linear Speed: 7.94 μm/min 79.4 mm/min Adjusting Resolution: 7.94 μm/min Distance Resolution: 0.65 μm Linear Force: > 0 N Setting Mode: Membrane Keypad and rotary coded switch Accuracy: ± 0.5% error in the condition of 30% of max. infusion distance Display: 8x64 graphic LCD External Control: Input control: start/stop Output control: start/stop, direction (OC gate) Communication Interface: RS485 Power:AC00V40VorDCV/3.A Power Consumption: 4W OperatingCondition:Temperature040 Relative humidity 80 % ControllerDimensions(L W H): Controller Weight: 0.9 Kg DriveUnitDimensions(L W H): (mm) DriveUnitWeight:0.6Kg IP Rating: IP TSB/W009B Specifications Max. Infusion Distance: 90 mm AcceptableSyringe:5μL60mL Linear Speed: 7.9 μm/min 79.4 mm/min Adjusting Resolution: 7.94 μm/min Distance Resolution: 0.65 μm Linear Force: > 90 N Setting Mode: Membrane Keypad and rotary coded switch Accuracy: ± 0.5% error in the condition Of 30% of max. Infusion distance Display: 8x64 graphic LCD External Control: Input control: start/stop Output control: start/stop, direction (OC gate) Communication Interface: RS485 Power:AC00V 40VorDCV/3.A Power Consumption: 34W OperatingCondition:Temperature040 Relative humidity 80 % ControllerDimensions(L W H): Controller Weight: 0.9 Kg DriveUnitDimensions(L W H): (mm) DriveUnitWeight:3Kg IP Rating: IP4 3 4

14 BaodingLongerPrecisionPumpCo.,Ltd ADD: Building A,Chuangye Center Baoding National High Tech Industrial Development Zone Baoding, Hebei, China 0705 TEL: FAX: E mail: longer@longerpump.com Longer Syringe Pump Operating Manual SYRINGE PUMP OPERATING MANUAL TSA/L007A TSA/L007A TSB/W009B Baoding Longer Precision Pump Co., Ltd.

kd Scientific Model 200 Series

kd Scientific Model 200 Series Contents Introduction 1 Specifications 2 Features 3 Operating Instructions 13 Power switch 6 Syringe loading 6 Withdrawal operation 6 Menu features 8 Keypad functions 8 Fast