Allen-Bradley Replacements

Transcription

1 Digital Programmable Controller Wiring Systems (Catalog Number 49-IFM - - ) Product Data Contents Section Page Description Features and Benefits of Digital IFMs (Interface Modules) and Pre-wired Cables Features and Benefits of Ready to Wire Cables 3 IFM Options and Features 3 Standard Terminal Feedthrough Modules 4 Extra Terminal Modules 4 Sensor Modules 5 Fusible Modules 5 Accessories 6 How to Order Digital Pre-wired Cables and IFMs 7 How to Order Digital IFM Ready Cables and IFMs 7 How to Order I/O Module Ready Cables 7 IFM Catalog Number Explanation 8 Section Page Cable Catalog Number Explanation 9 Pre-wired Cable and IFM Selection Tables for Digital I/O 0 Modules Cable Technical Section 4 Pre-wired Cable Specifications 4 Pre-wired Cable Pinouts 5 IFM Ready Cable Specifications 0 CABLE*P Wiring 0 CABLE*Q Wiring 0 I/O Module Ready Cable Specifications IFM Technical Section 3 Specifications, Application Notes, and Pinouts 3 Dimensions 69 Adhesive Label Cards 74 Reference Publications Back Cover Allen-Bradley Replacements

2 Digital Programmable Controller Wiring Systems Description Features and Benefits of Digital IFMs (Interface Modules) and Pre-wired Cables The Bulletin 49 Digital Programmable Controller Wiring System Product Line consists of IFMs (Interface Modules), Pre-wired Cables and Ready-to-Wire Cables. These products aid in the installation of Allen-Bradley Programmable Controller I/O Modules. IFMs and pre-wired cables replace terminal blocks and up to 50% of the point-to-point wiring between the programmable controller and field devices. They are available for over 60 different 746 SLC 500, 756 ControlLogix, and 77 PLC Digital I/O Isolated and Non Isolated Modules. IFMs allow you to conveniently incorporate additional terminations, LED status indicators or overcurrent protection into your I/O circuitry. Faster Installation Time Pre-wired cables have the I/O module terminal block or wiring arm already wired-up on one end and a cable connector on the other. No need to measure, cut, strip, label, and terminate 0 to 40 wires per I/O module. Simply attach the wiring arm or removable terminal block end of the cable to the I/O module and snap the cable connector end of the cable to the IFM and you are ready to wire out to field devices. To assist in faster installation time, all of the Bulletin 49 pre wired digital cables are offered in four standard lengths (0.5m,.0m,.5m, and 5.0m) to fit a variety of applications. In addition, custom length cables (made to order) are also available, refer to page 0. Successful System Start-ups The pre-wired cables are 00% tested for continuity. No more crossed wires and loose connections between the I/O module and the terminal blocks on the DIN rail. With the pre-wired cable and IFM, your application will have a much higher rate of success at initial start-up. Simplified Troubleshooting IFMs with optional LED indicators provide the field side status of the I/O circuitry. No more guess work determining where a problem resides. The combination of the logic side I/O module LEDs and the field side IFM LEDs help to determine if the problem resides in the I/O module or the field device/wiring. Fusible IFMs provide termination for output modules as well as the ability to incorporate overcurrent protection. Optional on-board blown fuse indicators help to quickly identify which output or input circuit had the fault reducing costly troubleshooting and downtime. Reduced Panel Space Extra terminal, sensor, and fusible IFMs have terminals for connecting the I/O points. In addition, they contain commoned terminals that are used as power busses for field input and output devices. No additional terminal blocks are needed to provide power to the field-devices saving valuable panel/din rail space. Just bring in one power connection per group to the commoned terminals and terminate the other side of your input or output devices to the power bus. IFMs provide complete and compact wiring all on one IFM! Narrow IFMs have been designed to even further reduce panel space. They require 45% less panel space than the standard length IFMs, making them well suited for tightly packed enclosures. The high density narrow IFMs have two rows of ten field wiring terminals for an overall length of.36 (60mm). The standard IFMs have one row of twenty terminals for an overall length of 4.33 (0mm). Quality-Looking Panel The pre-wired cables and IFMs organize your wiring and terminations for a consistent look to your panel. Pre-printed adhesive labels for the terminal wiring neatly identify field-side connections.

3 Digital Programmable Controller Wiring Systems 3 Features and Benefits of Ready to Wire Cables Ready-to-wire cables provide one end of the cable pre-terminated, for either an IFM or a programmable controller I/O module. IFM-ready cables have a cable connector on one end to attach to the IFM and free conductors on the other end to wire to your own type of device. I/O module-ready cables have a wiring arm or removable terminal block wired up on one end and free conductors on the other to wire into standard terminal blocks or other types of connectors. Cables Fit Your Panel The Bulletin 49 Ready-to-Wire Cables are offered in three standard lengths (.0m,.5m, and 5.0m) to fit a variety of applications. Custom length cables (made to order) are also available, refer to page 0. Easy to Wire Both the IFM-ready cables and the I/O module-ready cables have individually colored conductors for quick wire-to-terminal coordination. IFM Options and Features Meets Most Panel Specifications The I/O module-ready cables utilize #8 AWG conductors for strength and rigidity on longer cable runs. They are designed to the maximum specification of its connecting I/O module. IFMs, similar to groups of terminal blocks, are available with either 0 pin or 40 pin cable connectors. The number of field-side wiring terminals varies with the type of module from one to three terminals per I/O point. LEDs and fuse clips are available on-board the IFMs to customize your wiring system to your application and provide assistance with troubleshooting your control panel. The IFMs are compatible with the pre-wired cables or the IFM-ready cables. All of the IFMs have the following features: Keyed cable connector with locking tabs for easy installation and secure connection of IFMs. UL Component Recognized (File E374 Guide NRAQ); CSA Certified (File LR34 Class 307); UL recognized per Canadian Safety Standards (cur) (File E374 Guide NRAQ); and CE Approved. Large rectangular write-on area acts as built-in group marking carrier for programmable controller rack, module group, and/or slot information. Pre-printed and blank adhesive marking strips are provided to identify either Programmable Controller I/O field-side wiring terminals or your own application requirements. High-density field-side wiring terminals allow more connections in less space and accommodate #- AWG wire. Continuous current rating of amps per circuit supports higher-current programmable controller output modules. Standard DIN #3 rail mounting for quick installation. Allen-Bradley Replacements

4 4 Digital Programmable Controller Wiring Systems Standard Terminal Modules L (+) Standard terminal modules provide one field-side wiring terminal per programmable controller input or output point as well as enough terminals for the I/O module power connections. The standard terminal modules are ideal for applications where the I/O device commons are terminated in the field or remotely from the I/O module panel. Extra Terminal Modules Voltage indicating LEDs are available on the standard, extra terminal and sensor IFMs. The LEDs provide field-side troubleshooting diagnostics: the on/off status of an input device or the on/off status of the programmable controller output circuit. When used in conjunction with the logic-side programmable controller LEDs, the IFM LEDs can help determine if a problem resides in the I/O module or field device/wiring. The LED modules have unique circuitry that allows compatibility with sinking or sourcing input or output modules. Extra terminal modules provide two or four field-side terminals per input or output point. Non Isolated IFMs have two terminals per input or output. Isolated IFMs have two or four terminals per input or output. Non-Isolated IFMs have the lower row of extra terminals commoned together in groups of 0➊, to serve as a power bus for the field device commons. Isolated IFMs have terminals isolated into 8 or 6 groups which allows each group of I/O devices to reference a different power source. The extra terminal modules are beneficial in applications where the I/O devices are terminated within the same panel as the I/O modules eliminating the need for many additional terminal blocks. These modules are also available with optional field-side status LEDs for troubleshooting inputs and outputs. ➊ Except Catalog Numbers 49-IFM0D4A- and -IFM0D0A- which are in groups of 0.

5 Digital Programmable Controller Wiring Systems 5 Sensor Modules Sensor _ + Sensor modules provide three field-side terminals per input point. The middle and lower rows of terminals commoned together in groups of 8, serve as power busses for 3-wire sensor types of devices eliminating additional terminal blocks and jumpering systems. Optional field-side LEDs identify the on/off condition of the sensor signal. The sensor modules provide a compact method of terminating and powering 4V AC/DC or 0V AC (IFM0F 3 only) 3 wire devices. Fusible Modules Fusible modules provide a convenient method of adding overcurrent protection into your programmable controller wiring. These modules have 5 x 0mm fuse clips on-board and are available with and without blown fuse indication. The 4V or 0V blown fuse indicators reduce the troubleshooting time to locate and replace a blown fuse on the IFM. The fusible modules have an easy-to-remove see-through Plexiglass cover to prevent objects from contacting fuse circuitry under normal operation. Standard fuse holders reside in the IFM aiding in the removal of a fuse with a fuse puller (fuses are not included). The fusible modules also have or 4 terminals per I/O point to create a power bus for input or output load connections. Fusible modules are available in both isolated and non-isolated versions. There are a select number of fusible IFMs available for input modules. Allen-Bradley Replacements

6 6 Digital Programmable Controller Wiring Systems Accessories Cat. No. 49-IFMFH Fuse Holder Cat. No. 49-ISOSW- Isolation Switch Plug Cat. No. 49-SJM5-0 Insulated Side Jumper Replacement Fuse Holders The 49-IFMFH fuse holders accommodate a 5 x 0mm fuse or the 49-ISOSW- isolation switch plug and reside in the IFM under normal operation. All of the fusible 49 IFMs come standard with fuse holders. Most IFMs come with 0 fuse holders; but 0 fuse holders are included with 49-IFM0F-FS-, 49-IFM0F-FS4-, and 49-IFM0F-FS0-; 40 fuse holders are included with 49-IFM40F-F-, 49-IFM40F-F4-, and 49-IFM40F-F0-. Replacement fuse holders are available in packages of 0. Isolation Switch Plugs The 49-ISOSW- is an isolation switch or dummy fuse in a 5 x 0mm fuse form factor. The isolation switch plugs will fit into the 49-IFMFH fuse holders. If fusing is not desired on a fusible IFM, the 49-ISOSW- can be used to provide feed-through functionality under normal operation and isolation switch functionality once power has been removed from the circuit. The isolation switch can then be opened for maintenance and troubleshooting. Metering equipment can also be inserted into a -wire transmitter circuit to measure input loop current. The 49-ISOSW- isolation switch plugs are available in packages of 4. Insulated Side Jumpers The 49-SJM5-0 is a 0-pole comb-style insulated side jumper. A side cutter can be used to cut the 0-pole jumper into smaller pole assemblies. The jumper fits the field-side terminal spacings on all of the 49-IFMs and is a convenient means of connecting unused inputs together on the feed-through IFMs. The 49-SJM5-0 insulated side jumpers are available in packages of 0.

7 Digital Programmable Controller Wiring Systems 7 How to Order Digital Pre-wired Cables and IFMs How to Order IFM Ready Cables and IFMs To order the proper pre-wired cable and IFM, you need to know:. The catalog number(s) of the Digital I/O module(s).. The desired cable length (0.5m,.0m,.5m, 5.0m, or custom length). 3. If LEDs or fusing (check voltage ratings for LEDs) are needed. 4. If additional terminals for field devices are needed. Refer to the Pre-wired Cable and IFM Selection Tables on Page 0. For more information, refer to the Technical Section on IFMs on Page 3, and to the Technical Section on Pre-wired Cables on Page 4. To order the proper IFM Ready cable and IFM, you need to know:. If 0 or 40 wires/pins in the cable connection are required.. The desired cable length (0.5m,.0m,.5m, 5.0m, or custom length). 3. If LEDs or fusing (check voltage ratings for LEDs) are needed. 4. If additional terminals for field devices are needed. If 0 wires/pins in the cable connector are needed:. Use the 0 conductor IFM-ready cable (Catalog Number 49-CABLE_P).. Replace the _ in the catalog number with the code for the desired cable length ( 005 = 0.5m, 00 =.0m, 05 =.5m, 050 = 5.0m, or custom length). 3. Use a 0-point IFM (Catalog Number 49-IFM0 _). Refer to the Technical Section on IFMs on Page 3. If 40 wires/pins in the cable connector are needed:. Use the 40 conductor IFM-ready cable (Catalog Number 49-CABLE_Q).. Replace the _ in the catalog number with the code for the desired cable length ( 005 = 0.5m, 00 =.0m, 05 =.5m, 050 = 5.0m, or custom length). 3. Use a 40-point IFM (Catalog Number 49-IFM40 _). Refer to the Technical Section on IFMs on Page 3. For pinout and wiring information refer to the Technical Section on IFM-Ready Cables on Page 0. How to Order I/O Module Ready Cables To order the proper I/O Module Ready Cable, you need to know:. The type of connector needed for the I/O module(s) (Catalog Number of the wiring arm or removable terminal block).. The code for the desired cable length ( 00 =.0m, 05 =.5m, 050 = 5.0m, or custom length). For a listing of cables offered and their corresponding I/O module connectors, specifications, and wiring, refer to the Technical Section on I/O Module-Ready Cables on Page. Allen-Bradley Replacements

8 8 Digital Programmable Controller Wiring Systems IFM Catalog Number Explanation Important: The following IFM catalog number breakdown is for explanation purposes only. It is not a product configurator. All combinations of fields are not valid product catalog numbers. First, select the desired IFM using the steps in How to Order Digital Pre-wired Cables and IFMs on page 7. Then use this breakdown for verification and explanation only. 49 IFM0F F0 Bulletin Number IFM Product Type Interface Module Number of Cable Connector Pins 0 Twenty Pins 40 Forty Pins Number of Field-Side Terminals Blank One per I/O Point Two per I/O Point 3 Three per I/O Point 4 Four per I/O Point Status Indication Status Indication F No LEDs Blank No Fuse Clips FN Narrow IFM F 5x0mm Fuse Clips D4 D4N D4A DS4 DS4A D0 D0N 4V LEDs for Output Modules Narrow IFM with 4V LEDs 4V LEDs for Input Modules Isolated IFM with 4/48V LEDs for Outputs Isolated IFM with 4V LEDs for Inputs 0V LEDs for Output Modules Narrow IFM with 0V LEDs F4 F4A F0 F0A FS 5x0mm Fuse Clips with 4V Blown Fuse Indicators for Output Modules 5x0mm Fuse Clips with 4V Blown Fuse Indicators for Input Modules 5x0mm Fuse Clips with 0V Blown Fuse Indicators for Output Modules 5x0mm Fuse Clips with 0V Blown Fuse Indicators for Input Modules Isolated IFM with 5x0mm Fuse Clips D0A DS0 DS0A 0V LEDs for Input Modules Isolated IFM with 0V LEDs for Outputs Isolated IFM with 0V LEDs for Inputs FS4 FS4A FS0 FS0A Isolated IFM with 5x0mm Fuse Clips with 4V Blown Fuse Indicators for Output Modules Isolated IFM with 5x0mm Fuse Clips with 4V Blown Fuse Indicators for Input Modules Isolated IFM with 5x0mm Fuse Clips with 0V Blown Fuse Indicators for Output Modules Isolated IFM with 5x0mm Fuse Clips with 0V Blown Fuse Indicators for Input Modules

9 Digital Programmable Controller Wiring Systems 9 Cable Catalog Number Explanation The following cable catalog number explanation may be used as a product configurator. All combinations of fields indicated produce valid product catalog numbers. 49 CABLE00A Bulletin Number Product Type CABLE Interface Cable Standard Cable Length meter (.64 feet) 00.0 meter (3.8 feet) 05.5 meters (8.0 feet) meters (6.40 feet) Custom Cable Length meters ( feet) 0. meter (0.38 feet) increments meters ( feet) 0.5 meter (.64 feet) increments meters ( feet).0 meter (3.8 feet) increments Status Indication A,B,C,D Pre wired Cables for 8 Point Isolated and 6 Point Digital 746 E,G,N,S I/O Modules➊ F Pre wired Cable for 6 Point Digital 77 I/O Modules➊ FF H J,K,L,M,R U,V,W,X Pre wired Cable with Fused Wiring Arm for 6 Point Digital 77 Output Modules➊ Pre wired Cable for 3 Point Digital 746 I/O Modules➊ Pre wired Cables for 6 Point Isolated and 3 Point Digital 77 I/O Modules➊ Pre wired Cables for 8 and 6 Point Digital 756 I/O Modules➊ Y,Z Pre wired cables for 6 Point Isolated and 3 Point Digital 756 I/O modules➊ P Digital IFM Ready Cable with 0 Conductors Q N3 RTBB RTBO RTBR TBCH TBNH WA WD WH WHF WN Digital IFM Ready Cable with 40 Conductors Digital I/O Module Ready Cable with 40 Point 746 N3 Wiring Arm Digital I/O Module Ready Cable with 6 Point 746 RT5B Terminal Block (Blue) Digital I/O Module Ready Cable with 6 Point 746 RT5C Terminal Block (Orange) Digital I/O Module Ready Cable with 6 Point 746 RT5R Terminal Block (Red) Digital I/O Module Ready Cable with 36 Point 756 TBCH Wiring Arm Digital I/O Module Ready Cable with 0 Point 756 TBNH Wiring Arm Digital I/O Module Ready Cable with 77 WA 8 Point Wiring Arm Digital I/O Module Ready Cable with 77 WD 6 Point Wiring Arm Digital I/O Module Ready Cable with 77 WH 6 Point Wiring Arm Digital I/O Module Ready Cable with 77 WHF 6 Point Fused Wiring Arm Digital I/O Module Ready Cable with 77 WN 3 Point Wiring Arm ➊ Refer to Cable Selection Tables on Pages 0 and for proper IFM and I/O module compatibility. Allen-Bradley Replacements

10 0 Digital Programmable Controller Wiring Systems Pre-wired Cable and IFM Selection Tables for Digital I/O Modules Note: Use the tables starting on page to select pre-wired cables and IFMs for either Bulletin 746 SLC, 756 ControlLogix, or 77 PLC Digital I/O Modules. Select the appropriate table (SLC, ControlLogix, or PLC). Locate your I/O module catalog number in the shaded area. Follow down the selected column to the cable selection code that indicates compatible IFMs. If the box is blank, the I/O module and IFM are not recommended for use together. Select the catalog number of the desired IFM. Refer to the page number indicated for technical information on the IFM. To configure a cable catalog number, order 49-CABLE➊➋. ➊ Cables are available in 0.5,.0,.5, and 5.0m lengths. Insert the cable length code into the catalog number. Cable length codes are as follows: 005 = 0.5m, 00 =.0m, 05 =.5m, and 050 = 5.0m. All 49 cables are also available in custom lengths. Contact your local Allen-Bradley distributor or sales office for availability. Custom Cable Lengths Length Increment Size Cable Length Codes Examples 0.m.0m 0.m CABLE05A.0m 0.0m 0.5m CABLE075B 0.0m 99.0m.0m CABLE50F Note: Some I/O modules may have recommended maximum cable lengths. Refer to the appropriate I/O module Product Data Publication for more information. ➋ Insert cable selection code (see tables starting on page ). Example: 49-CABLE005A is a 0.5m cable for the 746-IA6 input module.

11 Digital Programmable Controller Wiring Systems Pre-wired Cable and IFM Selection Table for Digital I/O Modules, (Continued) Type of IFM SLC Point Isolated and 6-Point Digital 746 I/O Modules Description IFM Catalog Number I/O Module Catalog Number 746-IA6 746-IB6 746-IC6 746-IG6 746-IH6 746-IN6 746-ITB6 746-ITV6 746-IV6 746-OA6 746-OB6 746-OB6E 746-OBP6 746-OG6 746-OV6 746-OVP6 746-OW6 746-OX8 Feed-Through 0-Point Standard 49-IFM0F A B B E B B B B B C E E E E E E D D 0-Point Narrow Standard 49-IFM0FN A B B E B B B B B G E E E E E E N N 0-Point Extra Terminal 49-IFM0F- A B B E B B B B B C E E E E E E D 0-Point Sensor 49-IFM0F-3 A B B E B B B B B LED Indicating 0-Point Standard with 4V LEDs 49-IFM0D4 B B B B B E E E E E D 0-Point Narrow Standard with 4V LEDs 49-IFM0D4N B B B B B E E E N 0-Point Standard with 0V LEDs 49-IFM0D0 A B C D 0-Point Narrow Standard with 0V LEDs 49-IFM0D0N A G N 0-Point Extra Terminal with 4V LEDs for Outputs 49-IFM0D4- E E E E E D 0-Point Extra Terminal with 4V LEDs for Inputs 49-IFM0D4A- B B B B B 0-Point Extra Terminal with 0V LEDs for Outputs 49-IFM0D0- C D 0-Point Extra Terminal with 0V LEDs for Inputs 49-IFM0D0A- A 0-Point Sensor with 4V LEDs 49-IFM0D4-3 B B B B B 0-Point Isolated with 4/48V LEDs and 4 Terminals per Output 49-IFM0DS4-4 S 0-Point Isolated with 0V LEDs and 4 Terminals per Output 49-IFM0DS0-4 S Fusible 0-Point Extra Terminal for Outputs 49-IFM0F-F- C E E E E E D 0-Point Extra Terminal with 4V Blown Fuse Indicators for Outputs 49-IFM0F-F4- E E E E E D 0-Point Extra Terminal with 0V Blown Fuse Indicators for Outputs 49-IFM0F-F0- C D 0-Point Extra Terminal with 4V Blown Fuse Indicators for Inputs 49-IFM0F-F4A- B B B E E 0-Point Extra Terminal with 0V Blown Fuse Indicators for Inputs 49-IFM0F-F0A- A B 0-Point Isolated Extra Terminal for Outputs 49-IFM0F-FS- S 0-Point Isolated Extra Terminal w/4v Blown Fuse Indicators for Outputs 49-IFM0F-FS4- S 0-Point Isolated Extra Terminal w/0v Blown Fuse Indicators for Outputs 49-IFM0F-FS0- S SLC Point Digital 746 I/O Modules I/O Module Catalog No. Type of IFM Description IFM Catalog Number Feed-Through 40-Point Standard 49-IFM40F H H H➊ H➊ 40-Point Extra Terminal 49-IFM40F- H H H➊ H➊ 40-Point Sensor 49-IFM40F-3 H H LED Indicating 40-Point Standard with 4V LEDs 49-IFM40D4 H H H➊ H➊ 40-Point Extra Terminal with 4V LEDs for Outputs 49-IFM40D4- H➊ H➊ 40 Point Extra Terminal with 4V LEDs for Inputs 49-IFM40D4A- H H 40-Point Sensor with 4V LEDs 49-IFM40D4-3 H H Fusible 40-Point Extra Terminal for Outputs 49-IFM40F-F- H➊ H➊ 40-Point Extra Terminal with 4V Blown Fuse Indicators for Outputs 49-IFM40F-F4- H➊ H➊ ➊ 5.0m cable length is not recommended for use with the 746 OB3 and 746 OV3 SLC Output Modules. Note: The 49-IFM40D0-, 49-IFM40D0A-, 49-IFM40DS4-4, 49-IFM40DS4A-4, 49-IFM40DS0-4, 49-IFM40DS0A-4, 49-IFM40F-F0-, 49-IFM40F- FS-, 49-IFM40F-FS4-, 49-IFM40F-FS0-, 49-IFM40F-FS0-4, 49-IFM40F-FS4A-4, and 49-IFM40F-FS0A-4 are not compatible with I/O Modules listed in the table above. 746-IB3 746-IV3 746-OB V3 Allen-Bradley Replacements

12 Digital Programmable Controller Wiring Systems Pre-wired Cable and IFM Selection Tables for Digital I/O Modules, (Continued) ControlLogix 8- and 6-Point Digital 756 I/O Modules I/O Module Cat. No. Type of IFM Description IFM Catalog Number 756 IA8D 756 IA6 756 IB6 756 IC6 756 IN6 756 OA8 756 OA8D 756 OA8E 756 OA6 756 OB8 756 OB6E 756 OC8 756 ON8 Feed-Through 0-Point Standard 49-IFM0F U X X X X U U U X U X U U 0-Point Narrow Standard 49-IFM0FN U X X X X U U U X U X U U 0-Point Extra Terminal 49-IFM0F- U X X X X U U U X U X U U 0-Point 3 Wire Sensor 49-IFM0F-3 X X X X LED Indicating 0-Point Standard with 4V LEDs 49-IFM0D4 X X X 0-Point Narrow Standard with 4V LEDs 49-IFM0D4N X X X 0-Point Standard with 0V LEDs 49-IFM0D0 U X 0-Point Narrow Standard with 0V LEDs 49-IFM0D0N U X X 0-Point Extra Terminal with 4V LEDs for Outputs 49-IFM0D4- X 0-Point Extra Terminal with 4V LEDs for Inputs 49-IFM0D4A- X X 0-Point Extra Terminal with 0V LEDs for Outputs 49-IFM0D0- X 0-Point Extra Terminal with 0V LEDs for Inputs 49-IFM0D0A- U X 0-Point Sensor with 4V LEDs 49-IFM0D4-3 X X 0-Point Isolated with 4/48V LEDs and 4 Terminals per Output 49-IFM0DS4-4 W W W 0-Point Isolated with 0V LEDs and 4 Terminals per Output 49-IFM0DS0-4 W V V Fusible 0-Point Extra Terminal for Outputs 49-IFM0F-F- X X 0-Point Extra Terminal with 4V Blown Fuse Indicators for Outputs 49-IFM0F-F4- X 0-Point Extra Terminal with 0V Blown Fuse Indicators for Outputs 49-IFM0F-F0- X 0-Point Extra Terminal with 4V Blown Fuse Indicators for Inputs 49-IFM0-F4A- X X 0-Point Extra Terminal with 0V Blown Fuse Indicators for Inputs 49-IFM0-F0A- X 0-Point Isolated Extra Terminal for Outputs 49-IFM0-FS- W V V W W W 0-Point Isolated Extra Terminal with 4V Blown Fuse Indicators for Outputs 49-IFM0-FS4- W W W 0-Point Isolated Extra Terminal with 0V Blown Fuse Indicators for Outputs 49-IFM0-FS0- W V V Type of IFM ControlLogix 6-Point Isolated and 3-Point Digital 756 I/O Modules I/O Module Cat. No. Description IFM Catalog Number 756 IA6I 756 IB6D 756 IB6I 756 IB3 756 IH6I 756 OA6I 756 OB8EI 756 OB6D 756 OB6I 756 OB3 756 OH8I 756 OW6I 756 OX8I Feed-Through 40-Point Standard 49-IFM40F Y Y Y Z Y Y Y Y Y Z Y Y Y 40-Point Extra Terminal 49-IFM40F- Y Z Y Z 40-Point Sensor 49-IFM40F-3 Z LED Indicating 40-Point Standard with 4V LEDs 49-IFM40D4 Z Z 40-Point Extra Terminal with 4V LEDs for Outputs 49-IFM40D4- Z 40-Point Extra Terminal with 4V LEDs for Inputs 49-IFM40D4A- Z 40-Point Extra Terminal with 0V LEDs for Outputs 49-IFM40D0-40-Point Extra Terminal with 0V LEDs for Inputs 49-IFM40D0A- 40-Point Sensor with 4V LEDs 49-IFM40D4-3 Z 40-Point Isolated with 4/48V LEDs and 4 Terminals per Output 49-IFM40DS4-4 Y Y Y Y Y 40-Point Isolated with 4V LEDs and 4 Terminals per Input 49-IFM40DS4A-4 Y Y 40-Point Isolated with 0V LEDs and 4 Terminals per Output 49-IFM40DS0-4 Y Y Y 40-Point Isolated with 0V LEDs and 4 Terminals per Input 49-IFM40DS0A-4 Y Fusible 40-Point Extra Terminal for Outputs 49-IFM40F-F- Z 40-Point Extra Terminal with 4V Blown Fuse Indicators for Outputs 49-IFM40F-F4- Z 40-Point Extra Terminal with 0V Blown Fuse Indicators for Outputs 49-IFM40F-F0-40-Point Isolated Extra Terminal for Outputs 49-IFM40F-FS- Y Y Y Y Y Y Y 40-Point Isolated Extra Terminal with 4V Blown Fuse Indicators for Outputs 49-IFM40F-FS4- Y Y Y Y Y 40-Point Isolated Extra Terminal with 0V Blown Fuse Indicators for Outputs 49-IFM40F-FS0- Y Y Y Y 40-Point Isolated with 0V Blown Fuse Indicators and 4 Terminals per Output 49-IFM40F-FS0-4 Y Y Y 40-Point Isolated with 4V Blown Fuse Indicators and 4 Terminals per Input 49-IFM40F-FS4A-4 Y Y 40-Point Isolated with 0V Blown Fuse Indicators and 4 Terminals per Input 49-IFM40F-FS0A-4 Y Y

13 Digital Programmable Controller Wiring Systems 3 Pre-wired Cable and IFM Selection Tables for Digital I/O Modules, (Continued) PLC 6-Point Digital 77 I/O Modules I/O Module Cat. No. Type of IFM Description IFM Catalog Number 77-IAD 77-IBD 77-ICD 77-IGD 77-IND Feed-Through 0-Point Standard 49-IFM0F F F F F F F,FF F,FF F F,FF 0-Point Narrow Standard 49-IFM0FN F F F F F F,FF F,FF F F,FF 0-Point Extra Terminal 49-IFM0F- F F F F F F,FF F,FF F F,FF 0-Point 3 Wire Sensor 49-IFM0F-3 F F F F F LED Indicating 0-Point Standard with 4V LEDs 49-IFM0D4 F F F F,FF F,FF F,FF 0-Point Narrow Standard with 4V LEDs 49-IFM0D4N F F F F,FF F,FF F,FF 0-Point Standard with 0V LEDs 49-IFM0D0 F 0-Point Narrow Standard with 0V LEDs 49-IFM0D0N F F,FF 0-Point Extra Terminal with 4V LEDs for Outputs 49-IFM0D4- F,FF F,FF F,FF 0-Point Extra Terminal with 4V LEDs for Inputs 49-IFM0D4A- F F F 0-Point Extra Terminal with 0V LEDs for Outputs 49-IFM0D0- F,FF 0-Point Extra Terminal with 0V LEDs for Inputs 49-IFM0D0A- F 0-Point Sensor with 4V LEDs 49-IFM0D4-3 F F 0-Point Isolated with 4/48V LEDs and 4 Terminals per Output 49-IFM0DS4-4 0-Point Isolated with 0V LEDs and 4 Terminals per Output 49-IFM0DS0-4 Fusible 0-Point Extra Terminal for Outputs 49-IFM0F-F- F F F 0-Point Extra Terminal with 4V Blown Fuse Indicators for Outputs 49-IFM0F-F4- F F F 0-Point Extra Terminal with 0V Blown Fuse Indicators for Outputs 49-IFM0F-F0- F 0-Point Extra Terminal with 4V Blown Fuse Indicators for Inputs 49-IFM0-F4A- F F F 0-Point Extra Terminal with 0V Blown Fuse Indicators for Inputs 49-IFM0-F0A- F 0-Point Isolated Extra Terminal for Outputs 49-IFM0-FS- 0-Point Isolated Extra Terminal with 4V Blown Fuse Indicators for Outputs 49-IFM0-FS4-0-Point Isolated Extra Terminal with 0V Blown Fuse Indicators for Outputs 49-IFM0-FS0- Type of IFM PLC 6-Point Isolated and 3-Point Digital 77 I/O Modules Description IFM Catalog Number 77-OAD 77-OBD 77-OGD I/O Module Cat. No. 77-OND 77-IAN 77-IBN 77-ID6 77-IQ6 77-IVN 77-OAN 77-OBN 77-OD6 77-ODD 77-OQ6 77-OVN 77-OW6 77-OWN 77-OWNA Feed-Through 40-Point Standard 49-IFM40F J J M M K L L M M M L R L L 40-Point Extra Terminal 49-IFM40F- J J K L L L R L L 40-Point Sensor 49-IFM40F-3 J K LED Indicating 40-Point Standard with 4V LEDs 49-IFM40D4 J K L L L L 40-Point Extra Terminal with 4V LEDs for Outputs 49-IFM40D4- L L L L 40-Point Extra Terminal with 4V LEDs for Inputs 49-IFM40D4A- J K 40-Point Extra Terminal with 0V LEDs for Outputs 49-IFM40D0- L L L 40-Point Extra Terminal with 0V LEDs for Inputs 49-IFM40D0A- J 40-Point Sensor with 4V LEDs 49-IFM40D4-3 J K 40-Point Isolated with 4/48V LEDs and 4 Terminals per Output 49-IFM40DS4-4 M 40-Point Isolated with 4V LEDs and 4 Terminals per Input 49-IFM40DS4A-4 M 40-Point Isolated with 0V LEDs and 4 Terminals per Output 49-IFM40DS0-4 M M 40-Point Isolated with 0V LEDs and 4 Terminals per Input 49-IFM40DS0A-4 M Fusible 40-Point Extra Terminal for Outputs 49-IFM40F-F- L L L L L 40-Point Extra Terminal with 4V Blown Fuse Indicators for Outputs 49-IFM40F-F4- L L L L 40-Point Extra Terminal with 0V Blown Fuse Indicators for Outputs 49-IFM40F-F0- L L L 40-Point Isolated Extra Terminal for Outputs 49-IFM40F-FS- M M M 40-Point Isolated Extra Terminal with 4V Blown Fuse Indicators for Outputs 49-IFM40F-FS4- M 40-Point Isolated Extra Terminal with 0V Blown Fuse Indicators for Outputs 49-IFM40F-FS0- M M 40-Point Isolated with 0V Blown Fuse Indicators and 4 Terminals per Output 49-IFM40F-FS0-4 M M 40-Point Isolated with 4V Blown Fuse Indicators and 4 Terminals per Input 49-IFM40F-FS4A-4 M Allen-Bradley 40-Point Isolated with 0V Blown Fuse Indicators and 4 Terminals Replacements per Input 49-IFM40F-FS0A-4 M

14 4 Digital Programmable Controller Wiring Systems Cable Technical Section Pre wired Cable Specifications Bulletin 49 Pre wired Cables are designed to minimize control wiring in a panel. Pre-wired cables, when used with an IFM, replace the point-to-point wiring between Allen-Bradley programmable controller I/O modules and individual terminal blocks. The ready-to-wire cables provide one end of the cable pre-terminated, for either an IFM (IFM-ready cable) or a programmable controller I/O module (I/O module-ready cable). The pre wired cables have a 746 Removable Terminal Block, 756 Removable Terminal Block, or 77 Wiring Arm on one end and a cable connector on the other to connect to the IFM. The broad offering of pre-wired cables supports over 60 different 6- and 3-point SLC ControlLogix and PLC digital I/O modules. Refer to the Selection Tables starting on page for proper I/O module, IFM, and pre-wired cable coordination. For wiring information, refer to the Label Section on page 74. In addition, refer to Publication (Digital Programmable Controller Wiring Systems Installation Wiring Diagrams) or the Wiring System web page at b/chassis/49.html. Refer to the online documentation for new product information and for the most up to date set of wiring diagrams. Catalog Number Cable Lengths Insulation Rating Number of Conductors Pre-wired Cable Specifications Conductor Size Nominal Outer Diameter I/O Module Connector 49-CABLE➊A 0.5,.0,.5, 5.0m 300V 80 C 0 Conductors # AWG 9.0mm (0.36 ) 746-RT5R Red Removable Terminal Block 49-CABLE➊B 0.5,.0,.5, 5.0m 300V 80 C 0 Conductors # AWG 9.0mm (0.36 ) 746-RT5B Blue Removable Terminal Block 49-CABLE➊C 0.5,.0,.5, 5.0m 300V 80 C 0 Conductors # AWG 9.0mm (0.36 ) 746-RT5R Red Removable Terminal Block 49-CABLE➊D 0.5,.0,.5, 5.0m 300V 80 C 0 Conductors # AWG 9.0mm (0.36 ) 746-RT5C Orange Removable Terminal Block 49-CABLE➊E 0.5,.0,.5, 5.0m 300V 80 C 0 Conductors # AWG 9.0mm (0.36 ) 746-RT5B Blue Removable Terminal Block 49-CABLE➊F 0.5,.0,.5, 5.0m 300V 80 C 0 Conductors # AWG 9.0mm (0.36 ) 77-WH (6-Point/ Terminal) Wiring Arm 49-CABLE➊FF 0.5,.0,.5, 5.0m 300V 80 C 0 Conductors # AWG 9.0mm (0.36 ) 77-WHF (6-Point/ Terminal) Fused Wiring Arm 49-CABLE➊G 0.5,.0,.5, 5.0m 300V 80 C 0 Conductors # AWG 9.0mm (0.36 ) 746-RT5R Red Removable Terminal Block 49-CABLE➊H 0.5,.0,.5, 5.0m 300V 80 C 40 Conductors # AWG.7mm (0.46 ) 746-N3 40 Pin Cable Connector 49-CABLE➊J 0.5,.0,.5, 5.0m 300V 80 C 40 Conductors # AWG.7mm (0.46 ) 77-WN (3-Point/40 Terminal) Wiring Arm 49-CABLE➊K 0.5,.0,.5, 5.0m 300V 80 C 40 Conductors # AWG.7mm (0.46 ) 77-WN (3-Point/40 Terminal) Wiring Arm 49-CABLE➊L 0.5,.0,.5, 5.0m 300V 80 C 40 Conductors # AWG.7mm (0.46 ) 77-WN (3-Point/40 Terminal) Wiring Arm 49-CABLE➊M 0.5,.0,.5, 5.0m 300V 80 C 40 Conductors # AWG.7mm (0.46 ) 77-WN (3-Point/40 Terminal) Wiring Arm 49-CABLE➊N 0.5,.0,.5, 5.0m 300V 80 C 0 Conductors # AWG 9.0mm (0.36 ) 746-RT5C Orange Removable Terminal Block 49-CABLE➊R 0.5,.0,.5, 5.0m 300V 80 C 40 Conductors # AWG.7mm (0.46 ) 77-WN (3-Point/40 Terminal) Wiring Arm 49-CABLE➊S 0.5,.0,.5, 5.0m 300V 80 C 0 Conductors # AWG 9.0mm (0.36 ) 746-RT5C Orange Removable Terminal Block 49-CABLE➊U 0.5,.0,.5, 5.0m 300V 80 C 0 Conductors # AWG 9.0mm (0.36 ) 756-TBNH Removable Terminal Block 49-CABLE➊V 0.5,.0,.5, 5.0m 300V 80 C 0 Conductors # AWG 9.0mm (0.36 ) 756-TBNH Removable Terminal Block 49-CABLE➊W 0.5,.0,.5, 5.0m 300V 80 C 0 Conductors # AWG 9.0mm (0.36 ) 756-TBNH Removable Terminal Block 49-CABLE➊X 0.5,.0,.5, 5.0m 300V 80 C 0 Conductors # AWG 9.0mm (0.36 ) 756-TBNH Removable Terminal Block 49-CABLE➊Y 0.5,.0,.5, 5.0m 300V 80 C 40 Conductors # AWG.7mm (0.46 ) 756-TBCH Removable Terminal Block 49-CABLE➊Z 0.5,.0,.5, 5.0m 300V 80 C 40 Conductors # AWG.7mm (0.46 ) 756-TBCH Removable Terminal Block ➊ Cables are available in lengths of 0.5m,.0m,.5m and 5.0m. To order, insert the code for the desired cable length into the Catalog Number ( 005 = 0.5m, 00 =.0m, 05 =.5m, and 050 = 5.0m). Example: Catalog Number 49-CABLE005A is for a 0.5m cable for the 746-IA6 I/O Module. See also Custom Cable Lengths on page 0.

15 Digital Programmable Controller Wiring Systems 5 Pre wired Cable IFM Mating Connector Dimensions 9 mm (.5 in.) 38 mm (.50 in.) 54.4 mm (.5 in.) 39 mm (.54 in.) 34.3 mm (.35 in.) 9.0 mm (0.36 in.) 35.9 mm (.4 in.).7 mm (0.46 in.) 0 mm (.40 in.) 0 Point Cable Dimensions 40 Point Cable Dimensions 0 mm (.40 in.) Pre wired Cable IFM Mating Connector Dimensions Conductor Cable 40 Conductor Cable Pre wired Cable Pinouts The following diagrams illustrate how the individual conductors in the Digital Pre wired Cables are connected at both ends. The description listed first is the wire color of the conductor connected to the Removable Terminal Block (746 and 756 I/O) or Wiring Arm (77 I/O). The number that follows in parentheses is the corresponding pin number of the IFM mating connector at the other end. Red (3) Orange (5) White/Black (7) Green/Black (9) Blue/Black () Red/White (3) Blue/White (5) White/Red (7) Blue/Red (9) Red RTB Green (4) Blue (6) Red/Black (8) Orange/Black (0) Black/White () Green/White (4) Black/Red (6) Orange/Red (8) Red/Green (0) Red (3) Orange (5) White/Black (7) Green/Black (9) Blue/Black () Red/White (3) Blue/White (5) White/Red (7) Blue/Red (9) Blue RTB Green (4) Blue (6) Red/Black (8) Orange/Black (0) Black/White () Green/White (4) Black/Red (6) Orange/Red (8) Red/Green (0) 49-CABLE➊A 49-CABLE➊B Allen-Bradley Replacements

16 6 Digital Programmable Controller Wiring Systems Pre wired Cable Pinouts, (Continued) White () Black () Green (4) Blue (6) Red/Black (8) Orange/Black (0) Black/White () Green/White (4) Black/Red (6) Orange/Red (8) Red RTB Red (3) Orange (5) White/Black (7) Green/Black (9) Blue/Red (9) Red/Green (0) Blue/Black () Red/White (3) Blue/White (5) White/Red (7) White () Black () Green (4) Blue (6) Red/Black (8) Orange/Black (0) Black/White () Green/White (4) Black/Red (6) Orange/Red (8) Orange RTB Red (3) Orange (5) White/Black (7) Green/Black (9) Blue/Red (9) Red/Green (0) Blue/Black () Red/White (3) Blue/White (5) White/Red (7) 49-CABLE➊C 49-CABLE➊D White () Blue RTB Black () Red (3) Green (4) Orange (5) Blue (6) White/Black (7) Red/Black (8) Green/Black (9) Orange/Black (0) Blue/Black () Black/White () Red/White (3) Green/White (4) Blue/White (5) Black/Red (6) White/Red (7) Orange/Red (8) Red/Green (0) Blue/Red (9) 49-CABLE➊E Black () White () Blue/Red (9) Red (3) Green (4) Orange (5) Blue (6) White/Black (7) Red/Black (8) Green/Black (9) Orange/Black (0) Blue/Black () Black/White () Red/White (3) Green/White (4) Blue/White (5) Black/Red (6) White/Red (7) Orange/Red (8) Red/Green (0) A B C D E CAUTION DISCONNECT POWER BEFORE SERVICING FUSES ALL FUSES 30 50V A B C D E 49-CABLE➊FF Black () White () Blue/Red (9) Red (3) Green (4) Orange (5) Blue (6) White/Black (7) Red/Black (8) Green/Black (9) Orange/Black (0) Blue/Black () Black/White () Red/White (3) Green/White (4) Blue/White (5) Black/Red (6) White/Red (7) Orange/Red (8) Red/Green (0) White () Black () Green (4) Blue (6) Red/Black (8) Orange/Black (0) Black/White () Green/White (4) Black/Red (6) Orange/Red (8) 49-CABLE➊F 49-CABLE➊G Jumper Red RTB Red (3) Orange (5) White/Black (7) Green/Black (9) Blue/Red (9) Blue/Black () Red/White (3) Blue/White (5) White/Red (7)

17 Digital Programmable Controller Wiring Systems 7 Pre wired Cable Pinouts, (Continued) Black () White () Red (3) Green (4) Orange (5) Blue (6) White/Black (7) Red/Black (8) Green/Black (9) Orange/Black (0) Blue/Black () Black/White () Red/White (3) Green/White (4) Blue/White (5) Black/Red (6) White/Red (7) Orange/Red (8) Blue/Red (9) Red/Green (0) Orange/Green () Black/White Red () White/Black Red (3) Red/Black White (4) Green/Black White (5) Orange/Black White (6) Blue/Black White (7) Black/Red Green (8) White/Red Green (9) Red/Black Green (30) Green/Black Orange (3) 49-CABLE➊H Orange/Black Green (3) Blue/White Orange (33) Black/White Orange (34) White/Red Orange (35) Orange/White Blue (36) White/Red Blue (37) Black/White Green (38) White/Black Green (39) Red/White Green (40) Orange (5) Green/Black (9) Red/White (3) White/Red (7) White/Red Blue (37) Orange/Green () Green/Black White (5) White/Red Green (9) Blue/White Orange (33) White/Black Green (39) Blue (6) Orange/Black (0) Green/White (4) Orange/Red (8) Black/White Green (38) Black/White Red () Orange/Black White (6) Red/Black Green (30) Black/White Orange (34) Red/White Green (40) CABLE➊L Black () White/Black (7) Blue/Black () Blue/White (5) Blue/Red (9) Red (3) White/Black Red (3) Blue/Black White (7) Green/Black Orange (3) White/Red Orange (35) White () Red/Black (8) Black/White () Black/Red (6) Red/Green (0) Green (4) Red/Black White (4) Black/Red Green (8) Orange/Black Green (3) Orange/White Blue (36) White/Black (7) Blue/Black () Blue/White (5) Blue/Red (9) Red (3) White/Black Red (3) Blue/Black White (7) Green/Black Orange (3) White/Red Orange (35) White/Black Green (39) Red/Black (8) Black/White () Black/Red (6) Red/Green (0) Green (4) Red/Black White (4) Black/Red Green (8) Orange/Black Green (3) Orange/White Blue (36) Red/White Green (40) Red (3) White/Black (7) Blue/Black () Blue/White (5) Blue/Red (9) White/Black Green (39) White/Black Red (3) Blue/Black White (7) Green/Black Orange (3) White/Red Orange (35) Green (4) Red/Black (8) Black/White () Black/Red (6) Red/Green (0) Red/White Green (40) Red/Black White (4) Black/Red Green (8) Orange/Black Green (3) Orange/White Blue (36) Red/Green (0) Black () White () Green (4) Blue (6) Red/Black (8) Orange/Black (0) Black/White () Green/White (4) Black/Red (6) Orange/Red (8) CABLE➊J CABLE➊K 49-CABLE➊N Orange (5) Green/Black (9) Red/White (3) White/Red (7) Black () Orange/Green () Green/Black White (5) White/Red Green (9) Blue/White Orange (33) White/Red Blue (37) Blue (6) Orange/Black (0) Green/White (4) Orange/Red (8) White () Black/White Red () Orange/Black White (6) Red/Black Green (30) Black/White Orange (34) Black/White Green (38) Black () Orange (5) Green/Black (9) Red/White (3) White/Red (7) White/Red Blue (37) Orange/Green () Green/Black White (5) White/Red Green (9) Blue/White Orange (33) White () Blue (6) Orange/Black (0) Green/White (4) Orange/Red (8) Black/White Green (38) Black/White Red () Orange/Black White (6) Red/Black Green (30) Black/White Orange (34) Jumper Orange RTB Red (3) Orange (5) White/Black (7) Green/Black (9) Blue/Red (9) Blue/Black () Red/White (3) Blue/White (5) White/Red (7) Allen-Bradley Replacements

18 8 Digital Programmable Controller Wiring Systems Pre wired Cable Pinouts, (Continued) Orange (5) White/Black (7) Green/Black (9) Blue/Black () NC Red/White (3) Blue/White (5) White/Red (7) Blue/Red (9) NC Orange/Green () White/Black Red (3) Green/Black White (5) Blue/Black White (7) NC White/Red Green (9) Green/Black Orange (3) Blue/White Orange (33) White/Red Orange (35) NC Blue (6) Red/Black (8) Orange/Black (0) Black/White () NC Green/White (4) Black/Red (6) Orange/Red (8) Red/Green (0) NC Black/White Red () Red/Black White (4) Orange/Black White (6) Black/Red Green (8) NC Red/Black Green (30) Orange/Black Green (3) Black/White Orange (34) Orange/White Blue (36) NC Black () White/Black (7) Red/Black (8) Green/Black (9) Orange/Black (0) Blue/Black () Black/White () Red/White (3) Green/White (4) Red/Green (0) CABLE➊U White () Red (3) Green (4) Orange (5) Blue (6) Blue/White (5) Black/Red (6) White/Red (7) Orange/Red (8) Blue/Red (9) Red (3) White/Black (7) Blue/Black () Blue/White (5) Blue/Red (9) White/Black Red (3) Blue/Black White (7) Green/Black Orange (3) White/Red Orange (35) White/Black Green (39) Green (4) Red/Black (8) Black/White () Black/Red (6) Red/Green (0) Red/Black White (4) Black/Red Green (8) Orange/Black Green (3) Orange/White Blue (36) Red/White Green (40) 49-CABLE➊M Black () Orange (5) Green/Black (9) Red/White (3) White/Red (7) Orange/Green () Green/Black White (5) White/Red Green (9) Blue/White Orange (33) White/Red Blue (37) White () Blue (6) Orange/Black (0) Green/White (4) Orange/Red (8) Black/White Red () Orange/Black White (6) Red/Black Green (30) Black/White Orange (34) Black/White Green (38) NC White () Green (4) Blue (6) Red/Black (8) Black/White () Green/White (4) Black/Red (6) Orange/Red (8) NC CABLE➊V Black () Red (3) Orange (5) White/Black (7) Green/Black (9) Blue/Black () Red/White (3) Blue/White (5) White/Red (7) Blue/Red (9) 49-CABLE➊R Orange RTB White () Red (3) Green (4) Orange (5) Blue (6) White/Black (7) Red/Black (8) Green/Black (9) NC NC Black/White () Blue/Black () Green/White (4) Red/White (3) Black/Red (6) Blue/White (5) Orange/Red (8) White/Red (7) 49-CABLE➊S White () Green (4) Blue (6) Red/Black (8) Orange/Black (0) Black/White () Green/White (4) Black/Red (6) Orange/Red (8) Red/Green (0) CABLE➊W Red (3) Orange (5) White/Black (7) Green/Black (9) Black () Blue/Black () Red/White (3) Blue/White (5) White/Red (7) Blue/Red (9)

19 Digital Programmable Controller Wiring Systems 9 Pre wired Cable Pinouts, (Continued) Green (4) Red (3) Blue (6) Orange (5) Red/Black (8) White/Black (7) Orange/Black (0) Green/Black (9) Black () White () Black/White () Blue/Black () Green/White (4) Red/White (3) Black/Red (6) Blue/White (5) Orange/Red (8) Blue/Red (9) 0 9 White/Red (7) Red/Green (0) Orange (5) Blue (6) White/Black (7) Green/Black (9) Red/Black (8) Orange/Black (0) Blue/Black () Black/White () Red/White (3) Green/White (4) Blue/White (5) Black/Red (6) White/Red (7) Orange/Red (8) Blue/Red (9) Red/Green (0) Orange/Green () Black/White Red () White/Black Red (3) Red/Black White (4) Green/Black White (5) Orange/Black White (6) Blue/Black White (7) Black/Red Green (8) White/Red Green (9) Red/Black Green (30) Green/Black Orange (3) Orange/Black Green (3) Blue/White Orange (33) Black/White Orange (34) White/Red Orange (35) Orange/White Blue (36) NC NC NC NC CABLE➊X 49-CABLE➊Y White/Black (7) Blue/Black () Blue/White (5) Blue/Red (9) White/Black Red (3) Blue/Black White (7) Green/Black Orange (3) White/Red Orange (35) Black () Red/Black (8) Black/White () Black/Red (6) Red/Green (0) Red/Black White (4) Black/Red Green (8) Orange/Black Green (3) Orange/White Blue (36) White () Orange (5) Green/Black (9) Red/White (3) White/Red (7) Orange/Green () Green/Black White (5) White/Red Green (9) Blue/White Orange (33) White/Black Green (39) Blue (6) Orange/Black (0) Green/White (4) Orange/Red (8) Black/White Red () Orange/Black White (6) Red/Black Green (30) Black/White Orange (34) Red/White Green (40) 49-CABLE➊Z Allen-Bradley Replacements

20 0 Digital Programmable Controller Wiring Systems IFM Ready Cable Specifications IFM-ready cables have a cable connector on one end to attach to the IFM and either 0 or 40 individually colored conductors on the other end (CABLE➊P and CABLE➊Q, respectively). These cables allow the IFM to be used in specialty applications that require a custom connection. Catalog Number Cable Lengths Insulation Rating IFM Ready Cable Specifications Number of Conductors Conductor Size Nominal Outer Diameter Current/Conductor Compatible IFMs 49-CABLE➊P 0.5,.0,.5, 5.0m 300V 80 C 0 Conductors # AWG 9.0mm (0.36 ) Amps IFM0 _ 49-CABLE➊Q 0.5,.0,.5, 5.0m 300V 80 C 40 Conductors # AWG.7mm (0.46 ) Amps IFM40 _ CABLE➊P Wiring Each colored conductor is connected to one pin of the molded cable connector as listed in the tables below. 49-CABLE➊P Connector Pin Number Wire/Stripe Color Connector Pin Number Wire/Stripe Color Black Blue/Black White Black/White 3 Red 3 Red/White 4 Green 4 Green/White 5 Orange 5 Blue/White 6 Blue 6 Black/Red 7 White/Black 7 White/Red 8 Red/Black 8 Orange/Red 9 Green/Black 9 Blue/Red 0 Orange/Black 0 Red/Green ➊ Cables are available in lengths of.0m,.5m and 5.0m. To order, insert the desired cable length into the Catalog Number ( 00 =.0m, 05 =.5m, and 050 = 5.0m). Example: Catalog Number 49-CABLE05P is for a.5m, 0 conductor IFM-ready cable. See also Custom Cable Lengths Table on page 0. CABLE➊Q Wiring 49-CABLE➊Q Connector Pin Number Wire/Stripe Color Connector Pin Number Wire/Stripe Color Connector Pin Number Wire/Stripe Color Black 5 Blue/White 9 White/Red - Green White 6 Black/Red 30 Red/Black - Green 3 Red 7 White/Red 3 Green/Black - Orange 4 Green 8 Orange/Red 3 Orange/Black - Green 5 Orange 9 Blue/Red 33 Blue/White - Orange 6 Blue 0 Red/Green 34 Black/White - Orange 7 White/Black Orange/Green 35 White/Red - Orange 8 Red/Black Black/White - Red 36 Orange/White - Blue 9 Green/Black 3 White/Black - Red 37 White/Red - Blue 0 Orange/Black 4 Red/Black - White 38 Black/White - Green Blue/Black 5 Green/Black - White 39 White/Black - Green Black/White 6 Orange/Black - White 40 Red/White - Green 3 Red/White 7 Blue/Black - White 4 Green/White 8 Black/Red - Green

21 Digital Programmable Controller Wiring Systems I/O Module Ready Cable The I/O module-ready cables have a pre-wired wiring arm or removable terminal block on one end to connect the programmable controller I/O module and - 40 individually colored #8 AWG conductors on the other. These cables provide the convenience of a pre-wired I/O module connector while still allowing the flexibility to wire to standard terminal blocks. Catalog Number Cable Lengths Insulation Rating Pre-wired I/O module connectors include: 746-N3 40-point plug in connector (CABLE➊N3) point removable terminal blocks in Red, Blue and Orange (CABLE➊RTBR, ➊RTBB, ➊RTBO) 756-TBCH 36-point removable terminal block (CABLE➊TBCH) 756-TBNH 0-point removable terminal block (CABLE➊TBNH) 77-WH 6-point wiring arm (CABLE➊WH) 77-WN 3-point wiring arm (CABLE➊WN) 77-WHF 6-point fused wiring arm (with fuses) (CABLE➊WHF) 77-WD 6-point wiring arm (CABLE➊WD) 77-WA 8-point wiring arm (CABLE➊WA) I/O Module-Ready Cable Specifications Number of Conductors Conductor Size Nominal Outer Diameter I/O Module Connector 49-CABLE➊N3.0,.5, 5.0m 300V 80 C 40 # AWG 9.0mm (0.36 ) 746-N3 (40 Point) Plug in Connector 49-CABLE➊RTBB.0,.5, 5.0m 300V 80 C 0➋ #8 AWG 9.0mm (0.36 ) 77-RT5B Blue Removable Terminal Block 49-CABLE➊RTBO.0,.5, 5.0m 300V 80 C 0➋ #8 AWG 9.0mm (0.36 ) 77-RT5C Orange Removable Terminal Block 49-CABLE➊RTBR.0,.5, 5.0m 300V 80 C 0➋ #8 AWG 9.0mm (0.36 ) 77-RT5R Red Removable Terminal Block 49-CABLE➊TBCH.0,.5, 5.0m 300V 80 C 40➌ #8 AWG 9.0mm (0.36 ) 756-TBCH (36-Point) Removable Terminal Block 49-CABLE➊TBNH.0,.5, 5.0m 300V 80 C 0 #8 AWG.7mm (0.46 ) 77-TBNH (0-Point) Removable Terminal Block 49-CABLE➊WA.0,.5, 5.0m 300V 80 C ➋ #8 AWG 9.0mm (0.36 ) 77-WA (8-Point/0 Terminal) Wiring Arm 49-CABLE➊WD.0,.5, 5.0m 300V 80 C #8 AWG 9.0mm (0.36 ) 77-WD (6-Point/ Terminal) Wiring Arm 49-CABLE➊WH.0,.5, 5.0m 300V 80 C 0 #8 AWG 9.0mm (0.36 ) 77-WH (6-Point/ Terminal) Wiring Arm 49-CABLE➊WHF.0,.5, 5.0m 300V 80 C 0 #8 AWG 9.0mm (0.36 ) 77-WHF (6-Point/ Terminal) Fused Wiring Arm 49-CABLE➊WN.0,.5, 5.0m 300V 80 C 40 #8 AWG 9.0mm (0.36 ) 77-WN (3-Point/40 Terminal) Wiring Arm ➊ Cables are available in lengths of.0m,.5m and 5.0m. To order, insert the code for the desired cable length into the Catalog Number ( 00 =.0m, 05 =.5m and 050 = 5.0m). Example: Catalog Number 49-CABLE05WH is for a.5m cable with a pre-wired 77-WH Wiring Arm on one end. See also Custom Cable Lengths Table on page 0. ➋ Two conductors are not wired to I/O module connector. ➌ Four conductors are not wired to I/O module connector. I/O Module-Ready Cables and Mating I/O Modules Catalog Number Mating I/O Modules 49-CABLE➊N3 746-IB3, 746-IV3, 746-OB3, 746-OV3 49-CABLE➊RTBB 746-IB6, 746-IC6, 746-IG6, 746-IH6, 746-IN6, 746-ITB6, 746-ITV6, 746-IV6, 746-OB6, 746-OB6E, 746-OBP8, 746-OBP6, 746-OG6, 746-OV6, 746-OVP6 49-CABLE➊RTBO 746-OW6, 746-OX8 49-CABLE➊RTBR 746-IA6, 746-OA6, 746-OAP, 746-IM6 49-CABLE➊TBCH 756-IA6I, 756-IB6D, 756-IB6I, 756-IB3, 756-IF6, 756-IH6I, 756-IM6I, 756-OA6I, 756-OB8EI, 756-OB6D, 756-OB6I, 756-OB3, 756-OH8I, 756-OW6I, 756-OX8I 49-CABLE➊TBNH 756-IA8D, 756-IA6, 756-IB6, 756-IC6, 756-IF6I, 756-IF8, 756-IN6, 756-IR6I, 756-IT6I, 756-OA8, 756-OA8D, 756-OA8E, 756-OA6, 756-OB8, 756-OB6E, 756-OC8, 756-OF4, 756-OF6CI, 756-OF6VI, 756-OF8, 756-ON8 49-CABLE➊WA 77-IA, 77-IA, 77-IB, 77-IC, 77-IH, 77-IM, 77-IN, 77-IT, 77-IV, 77-OA, 77-OB, 77-OC, 77-OM, 77-ON, 77-OP 49-CABLE➊WD 77-ID, 77-ID0, 77-OD, 77-ODZ, 77-OR, 77-OW, 77-OYL, 77-OZL 49-CABLE➊WH 77-IAD, 77-IBD, 77-ICD, 77-IGD, 77-IMD, 77-IND, 77-OAD, 77-OBD, 77-OGD, 77-OMD, 77-OND 49-CABLE➊WHF 77-IBD➋, 77-OAD➋, 77-OBD➋, 77-OMD➋, 77-OND➋ 49-CABLE➊WN 77-IAN, 77-IBN, 77-ID6, 77-IQ6, 77-IV6, 77-OAN, 77-OBN, 77-OD6, 77-ODD, 77-OQ6, 77-OVN, 77-OW6, 77-OWN, 77-OWNA ➊ Cables are available in lengths of.0m,.5m and 5.0m. To order, insert the code for the desired cable length into the Catalog Number ( 00 =.0m, 05 =.5m and 050 = 5.0m). Example: Catalog Number 49-CABLE05WH is for a.5m cable with a pre-wired 77-WH Wiring Arm on one end. See also Custom Cable Lengths Table on page 0. Allen-Bradley ➋ Includes an optional 3A fuse in the Wiring Arm for 77 PLC mating I/O Modules. Replacements Note: The following I/O Modules do not have Removable Terminal Blocks (RTBs): 746-IA4, 746-IA8, 746-IB8, 746-IM4, 746-IM8, 746-IV8, 746-OA8, 746-OB8

22 Digital Programmable Controller Wiring Systems I/O Module Ready Cables (Continued) Below is the wire color table for I/O module-ready cables. Each colored conductor is given a reference number in the table. The reference number is used in the illustrations that follow to indicate the corresponding screw terminal CABLE➊TBCH CABLE➊TBNH CABLE➊N3 Reference Number Wire/Stripe Color Reference Number Wire/Stripe Color Black Orange/Green White Black/White - Red 3 Red 3 White/Black - Red 4 Green 4 Red/Black - White 5 Orange 5 Green/Black - White 6 Blue 6 Orange/Black - White 7 White/Black 7 Blue/Black - White 8 Red/Black 8 Black/Red - Green 9 Green/Black 9 White/Red - Green 0 Orange/Black 30 Red/Black - Green Blue/Black 3 Green/Black - Orange Black/White 3 Orange/Black - Green 3 Red/White 33 Blue/White - Orange 4 Green/White 34 Black/White - Orange 5 Blue/White 35 White/Red - Orange 6 Black/Red 36 Orange/White - Blue 7 White/Red 37 White/Red - Blue 8 Orange/Red 38 Black/White - Green 9 Blue/Red 39 White/Black - Green 0 Red/Green 40 Red/White - Green CABLE➊WN 49-CABLE➊WH 49-CABLE➊WHF 49-CABLE➊WD 49-CABLE➊WA 49-CABLE➊RTBR 49-CABLE➊RTBB 49-CABLE➊RTBO ➊ Cables are available in lengths of.0m,.5m and 5.0m. To order, insert the code for the desired cable length into the Catalog Number ( 00 =.0m, 05 =.5m and 050 = 5.0m). Example: Catalog Number 49-CABLE05WH is for a.5m cable with a pre-wired 77-WH Wiring Arm on one end. See also Custom Cable Lengths Table on page 0.

23 Digital Programmable Controller Wiring Systems 3 IFM Technical Section IFM Cat. No. Page No. for Specifications, Application Notes & Pinout Page No. for Adhesive Label Card IFM Cat. No. Page No. for Specifications, Application Notes & Pinout Page No. for Adhesive Label Card 49-IFM0F IFM40F IFM0FN IFM40F IFM0F IFM40F IFM0F IFM40D IFM0D IFM40D IFM0D4N IFM40D4A IFM0D IFM40D IFM0D0N IFM40D0A IFM0D IFM40D IFM0D4A IFM40DS IFM0D IFM40DS4A IFM0D0A IFM40S IFM0D IFM40DS0A IFM0DS IFM40F F IFM0DS IFM40F F IFM0F F IFM40F F IFM0F F IFM40F FS IFM0F F4A IFM40F FS IFM0F F IFM40F FS IFM0F F0A IFM40F FS IFM0F FS IFM40F FS4A IFM0F FS IFM40F FS0A IFM0F FS For all IFM dimensions, see page 69. For general Adhesive Label Card information, see page 74. For Field-Side Wiring Diagrams, refer to Publication (Digital Programmable Controller Wiring Systems Installation Wiring Diagrams) or the Wiring System web page at chassis/49.html. Refer to the online documentation for new product information and for the most up to date set of wiring diagrams. Symbols and Terminal Identification Conventions Used Throughout The Pinout Section = Fuse and Blown Fuse Indicator (where applicable) = LED Indicator = LED Indicator = Connector Pin = Fuse and Blown Fuse Indicator Allen-Bradley Replacements

24 4 Digital Programmable Controller Wiring Systems 49-IFM0F Specifications Approvals Voltage Rating Maximum Peak Voltage ➊ Maximum Current (per Circuit) Maximum Current (per Module) UL Component Recognized (File E374 Guide NRAQ) CSA Certified (File LR34 Class 307) CE Approved 0 3V AC/DC 600V p A Indicator Circuit Current (Nominal) No. of Terminals per Device Common Wire Range (Rated Cross Section) ➋ # # AWG (0. 4mm ) Wire Strip Length Recommended Tightening Torque Operating Temperature Range A 0.3 (8mm) lb.-in. ( Nm) 0 C to +60 C ➊ For transients >600V p, use a UL recognized suppression device rated at.5kv withstand. ➋ Maximum number of the same gauge stranded copper conductors allowed per wire funnel: AWG # #0 #8 #6 #4 # No. of Wires Application Notes. Compatibility To ensure proper operation with the I/O module, do not exceed the voltage and current ratings of the IFM. 3 Pinout A A A3. Wiring Refer to the Label Section on page 74. For Field-Side Wiring Diagrams, refer to Publication (Digital Programmable Controller Wiring Systems Installation Wiring Diagrams) or the Wiring System web page at chassis/49.html. Refer to the online documentation for new product information and for the most up to date set of wiring diagrams A8 A9 A0 3. Dimensions See page 69.

25 Digital Programmable Controller Wiring Systems 5 49-IFM0FN Specifications Approvals Voltage Rating Maximum Peak Voltage ➊ Maximum Current (per Circuit) Maximum Current (per Module) UL Component Recognized (File E374 Guide NRAQ) CSA Certified (File LR34 Class 307) CE Approved 0 3V AC/DC 600V p A Indicator Circuit Current (Nominal) No. of Terminals per Device Common Wire Range (Rated Cross Section) ➋ # # AWG (0. 4mm ) Wire Strip Length Recommended Tightening Torque Operating Temperature Range A 0.3 (8mm) lb.-in. ( Nm) 0 C to +60 C ➊ For transients >600V p, use a UL recognized suppression device rated at.5kv withstand. ➋ Maximum number of the same gauge stranded copper conductors allowed per wire funnel: AWG # #0 #8 #6 #4 # No. of Wires Application Notes. Compatibility To ensure proper operation with the I/O module, do not exceed the voltage and current ratings of the IFM. Pinout B B. Wiring Refer to the Label Section on page 74. For Field-Side Wiring Diagrams, refer to Publication (Digital Programmable Controller Wiring Systems Installation Wiring Diagrams) or the Wiring System web page at chassis/49.html. Refer to the online documentation for new product information and for the most up to date set of wiring diagrams. 8 0 B9 B0 A 3. Dimensions See page A 0 A9 9 A0 Allen-Bradley Replacements

26 6 Digital Programmable Controller Wiring Systems 49-IFM0F- Specifications Approvals Voltage Rating Maximum Peak Voltage ➊ Maximum Current (per Circuit) Maximum Current (per Module) UL Component Recognized (File E374 Guide NRAQ) CSA Certified (File LR34 Class 307) CE Approved 0 3V AC/DC 600V p A Indicator Circuit Current (Nominal) No. of Terminals per Device Common 0 Wire Range (Rated Cross Section) ➋ # # AWG (0. 4mm ) Wire Strip Length Recommended Tightening Torque Operating Temperature Range A 0.3 (8mm) lb.-in. ( Nm) 0 C to +60 C ➊ For transients >600V p, use a UL recognized suppression device rated at.5kv withstand. ➋ Maximum number of the same gauge stranded copper conductors allowed per wire funnel: AWG # #0 #8 #6 #4 # No. of Wires Application Notes. Compatibility To ensure proper operation with the I/O module, do not exceed the voltage and current ratings of the IFM. 3 Pinout B B B3. Wiring Refer to the Label Section on page 74. For Field-Side Wiring Diagrams, refer to Publication (Digital Programmable Controller Wiring Systems Installation Wiring Diagrams) or the Wiring System web page at chassis/49.html. Refer to the online documentation for new product information and for the most up to date set of wiring diagrams A A A A B8 B9 B0 3. Isolation The power bus is isolated into groups of 0 terminals. This allows each group of the I/O devices to reference a different power source. A9 A0 A9 A0 4. Dimensions See page 69.

27 Digital Programmable Controller Wiring Systems 7 49-IFM0F-3 Specifications Approvals Voltage Rating Maximum Peak Voltage ➊ Maximum Current (per Circuit) Maximum Current (per Module) UL Component Recognized (File E374 Guide NRAQ) CSA Certified (File LR34 Class 307) CE Approved 0 3V AC/DC 600V p A Indicator Circuit Current (Nominal) No. of Terminals per Device Common A 7 (bottom row). 8 (middle row) Wire Range (Rated Cross Section) ➋ # # AWG (0. 4mm ) Wire Strip Length Recommended Tightening Torque Operating Temperature Range 0.3 (8mm) lb.-in. ( Nm) 0 C to +60 C ➊ For transients >600V p, use a UL recognized suppression device rated at.5kv withstand. ➋ Maximum number of the same gauge stranded copper conductors allowed per wire funnel: AWG # #0 #8 #6 #4 # No. of Wires Application Notes. Compatibility To ensure proper operation with the I/O module, do not exceed the voltage and current ratings of the IFM. 3 Pinout C. Wiring Refer to the Label Section on page 74. For Field-Side Wiring Diagrams, refer to Publication (Digital Programmable Controller Wiring Systems Installation Wiring Diagrams) or the Wiring System web page at chassis/49.html. Refer to the online documentation for new product information and for the most up to date set of wiring diagrams. 3. Isolation The power busses are connected to one common (one bus has 7 terminals, and one bus has 8 terminals). All of the input devices used must reference the same power source. 8 0 C6 B B B7 B8 A A 4. Dimensions See page 69. A6 A7 A8 Allen-Bradley Replacements

28 8 Digital Programmable Controller Wiring Systems 49-IFM0D4 Specifications Approvals Voltage Rating Maximum Peak Voltage ➊ Maximum Current (per Circuit) Maximum Current (per Module) Indicator Circuit Current (Nominal) UL Component Recognized (File E374 Guide NRAQ) CSA Certified (File LR34 Class 307) CE Approved 0 30V AC/DC 600V p A No. of Terminals per Device Common 6 A ma Wire Range (Rated Cross Section) ➋ # # AWG (0. 4mm ) Wire Strip Length Recommended Tightening Torque Operating Temperature Range 0.3 (8mm) lb.-in. ( Nm) 0 C to +60 C ➊ For transients >600V p, use a UL recognized suppression device rated at.5kv withstand. ➋ Maximum number of the same gauge stranded copper conductors allowed per wire funnel: AWG # #0 #8 #6 #4 # No. of Wires Application Notes. Compatibility To ensure proper operation with the I/O module, do not exceed the voltage and current ratings of the IFM. When this IFM is used with a hard contact (relay) output circuit that switches an inductive load, surge suppression must be used (i.e., a N4004 diode reverse wired across a DC load).. Wiring Refer to the Label Section on page 74. For Field-Side Wiring Diagrams, refer to Publication (Digital Programmable Controller Wiring Systems Installation Wiring Diagrams) or the Wiring System web page at chassis/49.html. Refer to the online documentation for new product information and for the most up to date set of wiring diagrams. The LEDs are powered off the position terminal block. Make only one connection to the power source for normal operation. The test push button and wiring connection are only used to test the LEDs Pinout A A A3 A8 A9 A0 L (+) L ( ) 3. Isolation The LEDs are connected to one common. All of the I/O devices used must reference the same power source. 4. Dimensions See page 69.

29 Digital Programmable Controller Wiring Systems 9 49-IFM0D4N Specifications Approvals Voltage Rating Maximum Peak Voltage ➊ Maximum Current (per Circuit) Maximum Current (per Module) Indicator Circuit Current (Nominal) UL Component Recognized (File E374 Guide NRAQ) CSA Certified (File LR34 Class 307) CE Approved 0 30V AC/DC 600V p A No. of Terminals per Device Common 6 A ma Wire Range (Rated Cross Section) ➋ # # AWG (0. 4mm ) Wire Strip Length Recommended Tightening Torque Operating Temperature Range Application Notes. Compatibility To ensure proper operation with the I/O module, do not exceed the voltage and current ratings of the IFM. When this IFM is used with a hard contact (relay) output circuit that switches an inductive load, surge suppression must be used (i.e., a N4004 diode reverse wired across a DC load).. Wiring Refer to the Label Section on page 74. For Field-Side Wiring Diagrams, refer to Publication (Digital Programmable Controller Wiring Systems Installation Wiring Diagrams) or the Wiring System web page at chassis/49.html. Refer to the online documentation for new product information and for the most up to date set of wiring diagrams. The LEDs are powered off the position terminal block. Make only one connection to the power source for normal operation. The test push button and wiring connection are only used to test the LEDs. 3. Isolation The LEDs are connected to one common. All of the I/O devices used must reference the same power source. 4. Dimensions See page (8mm) lb.-in. ( Nm) 0 C to +60 C ➊ For transients >600V p, use a UL recognized suppression device rated at.5kv withstand. ➋ Maximum number of the same gauge stranded copper conductors allowed per wire funnel: AWG # #0 #8 #6 #4 # No. of Wires Pinout B B B9 B0 A A A9 A0 LED Circuit Allen-Bradley Replacements

30 30 Digital Programmable Controller Wiring Systems 49-IFM0D0 Specifications Approvals Voltage Rating Maximum Peak Voltage ➊ Maximum Current (per Circuit) Maximum Current (per Module) Indicator Circuit Current (Nominal) UL Component Recognized (File E374 Guide NRAQ) CSA Certified (File LR34 Class 307) CE Approved 85 3V AC/DC 600V p A A.5mA No. of Terminals per Device Common 8 Wire Range (Rated Cross Section) ➋ # # AWG (0. 4mm ) Wire Strip Length Recommended Tightening Torque Operating Temperature Range Application Notes. Compatibility To ensure proper operation with the I/O module, do not exceed the voltage and current ratings of the IFM. This IFM is not recommended for use with input devices or programmable controller output circuits having an off state leakage current exceeding 0.5mA. Use IFM0D0N instead, or use IFM0D0A for input modules and IFM0D0 for output modules. When this IFM is used with a hard contact (relay) output circuit that switches an inductive load, surge suppression must be used (i.e., a N4004 diode reverse wired across a DC load).. Wiring Refer to the Label Section on page 74. For Field-Side Wiring Diagrams, refer to Publication (Digital Programmable Controller Wiring Systems Installation Wiring Diagrams) or the Wiring System web page at chassis/49.html. Refer to the online documentation for new product information and for the most up to date set of wiring diagrams. 3. Isolation The LEDs are isolated into groups of 8 terminals. This allows each group of the I/O devices to reference a different power source. 4. Dimensions See page (8mm) lb.-in. ( Nm) 0 C to +60 C ➊ For transients >600V p, use a UL recognized suppression device rated at.5kv withstand. ➋ Maximum number of the same gauge stranded copper conductors allowed per wire funnel: AWG # #0 #8 #6 #4 # No. of Wires Pinout A A A3 A0 A A8 A9 A0 L ( ) L ( )

31 Digital Programmable Controller Wiring Systems 3 49-IFM0D0N Specifications Approvals Voltage Rating Maximum Peak Voltage ➊ Maximum Current (per Circuit) Maximum Current (per Module) Indicator Circuit Current (Nominal) UL Component Recognized (File E374 Guide NRAQ) CSA Certified (File LR34 Class 307) CE Approved 85 3V AC 600V p A A.5mA No. of Terminals per Device Common 6 Wire Range (Rated Cross Section) ➋ # # AWG (0. 4mm ) Wire Strip Length Recommended Tightening Torque Operating Temperature Range 0.3 (8mm) lb.-in. ( Nm) 0 C to +60 C ➊ For transients >600V p, use a UL recognized suppression device rated at.5kv withstand. ➋ Maximum number of the same gauge stranded copper conductors allowed per wire funnel: AWG # #0 #8 #6 #4 # No. of Wires Application Notes. Compatibility To ensure proper operation with the I/O module, do not exceed the voltage and current ratings of the IFM. When this IFM is used with a hard contact (relay) output circuit that switches an inductive load, surge suppression must be used (i.e., a N4004 diode reverse wired across a DC load). 8 Pinout B B B9. Wiring Refer to the Label Section on page 74. For Field-Side Wiring Diagrams, refer to Publication (Digital Programmable Controller Wiring Systems Installation Wiring Diagrams) or the Wiring System web page at chassis/49.html. Refer to the online documentation for new product information and for the most up to date set of wiring diagrams. 0 3 B0 A A 3. Isolation The LEDs are connected to one common. All of the I/O devices used must reference the same power source. 0 9 A9 A0 4. Dimensions See page 69. LED Circuit Allen-Bradley Replacements

32 3 Digital Programmable Controller Wiring Systems 49-IFM0D4- Specifications Approvals Voltage Rating Maximum Peak Voltage ➊ Maximum Current (per Circuit) Maximum Current (per Module) Indicator Circuit Current (Nominal) UL Component Recognized (File E374 Guide NRAQ) CSA Certified (File LR34 Class 307) CE Approved 0 30V AC/DC 600V p A No. of Terminals per Device Common 0 A ma Wire Range (Rated Cross Section) ➋ # # AWG (0. 4mm ) Wire Strip Length Recommended Tightening Torque Operating Temperature Range 0.3 (8mm) lb.-in. ( Nm) 0 C to +60 C ➊ For transients >600V p, use a UL recognized suppression device rated at.5kv withstand. ➋ Maximum number of the same gauge stranded copper conductors allowed per wire funnel: AWG # #0 #8 #6 #4 # No. of Wires Application Notes. Compatibility To ensure proper operation with the I/O module, do not exceed the voltage and current ratings of the IFM. When this IFM is used with a hard contact (relay) output circuit that switches an inductive load, surge suppression must be used (i.e., a N4004 diode reverse wired across a DC load). 3 0 Pinout B B B3 B0. Wiring Refer to the Label Section on page 74. For Field-Side Wiring Diagrams, refer to Publication (Digital Programmable Controller Wiring Systems Installation Wiring Diagrams) or the Wiring System web page at chassis/49.html. Refer to the online documentation for new product information and for the most up to date set of wiring diagrams B B8 B9 B0 3. Isolation The power bus and LEDs are isolated into groups of 0 terminals (8 LEDs). This allows each group of output devices to reference a different power source. 4. Dimensions See page 69. A A A A A9 A9 A0 A0 LED Circuit

33 Digital Programmable Controller Wiring Systems IFM0D4A- Specifications Approvals Voltage Rating Maximum Peak Voltage ➊ Maximum Current (per Circuit) Maximum Current (per Module) Indicator Circuit Current (Nominal) UL Component Recognized (File E374 Guide NRAQ) CSA Certified (File LR34 Class 307) CE Approved 0 30V AC/DC 600V p A No. of Terminals per Device Common 0 A ma Wire Range (Rated Cross Section) ➋ # # AWG (0. 4mm ) Wire Strip Length Recommended Tightening Torque Operating Temperature Range 0.3 (8mm) lb.-in. ( Nm) 0 C to +60 C ➊ For transients >600V p, use a UL recognized suppression device rated at.5kv withstand. ➋ Maximum number of the same gauge stranded copper conductors allowed per wire funnel: AWG # #0 #8 #6 #4 # No. of Wires Application Notes. Compatibility To ensure proper operation with the I/O module, do not exceed the voltage and current ratings of the IFM. Pinout B B. Wiring Refer to the Label Section on page 74. For Field-Side Wiring Diagrams, refer to Publication (Digital Programmable Controller Wiring Systems Installation Wiring Diagrams) or the Wiring System web page at chassis/49.html. Refer to the online documentation for new product information and for the most up to date set of wiring diagrams B3 B8 B9 B0 3. Isolation The power bus comprises 0 terminals connected together. The LEDs are connected to one common. All of the I/O devices used must reference the same power source. A A 4. Dimensions See page 69. A9 LED Circuit A0 Allen-Bradley Replacements

34 34 Digital Programmable Controller Wiring Systems 49-IFM0D0- Specifications Approvals Voltage Rating Maximum Peak Voltage ➊ Maximum Current (per Circuit) Maximum Current (per Module) Indicator Circuit Current (Nominal) UL Component Recognized (File E374 Guide NRAQ) CSA Certified (File LR34 Class 307) CE Approved 85 3V AC 600V p A A.5mA No. of Terminals per Device Common 0 Wire Range (Rated Cross Section) ➋ # # AWG (0. 4mm ) Wire Strip Length Recommended Tightening Torque Operating Temperature Range 0.3 (8mm) lb.-in. ( Nm) 0 C to +60 C ➊ For transients >600V p, use a UL recognized suppression device rated at.5kv withstand. ➋ Maximum number of the same gauge stranded copper conductors allowed per wire funnel: AWG # #0 #8 #6 #4 # No. of Wires Application Notes. Compatibility To ensure proper operation with the I/O module, do not exceed the voltage and current ratings of the IFM. When this IFM is used with a hard contact (relay) output circuit that switches an inductive load, surge suppression must be used (i.e., a N4004 diode reverse wired across a DC load). 3 0 Pinout B B B3 B0. Wiring Refer to the Label Section on page 74. For Field-Side Wiring Diagrams, refer to Publication (Digital Programmable Controller Wiring Systems Installation Wiring Diagrams) or the Wiring System web page at chassis/49.html. Refer to the online documentation for new product information and for the most up to date set of wiring diagrams B B8 B9 B0 3. Isolation The power bus and LEDs are isolated into groups of 0 terminals (8 LEDs). This allows each group of output devices to reference a different power source. 4. Dimensions See page 69. A A A A A9 A9 A0 A0 LED Circuit

35 Digital Programmable Controller Wiring Systems IFM0D0A- Specifications Approvals Voltage Rating Maximum Peak Voltage ➊ Maximum Current (per Circuit) Maximum Current (per Module) Indicator Circuit Current (Nominal) UL Component Recognized (File E374 Guide NRAQ) CSA Certified (File LR34 Class 307) CE Approved 85 3V AC 600V p A A.5mA No. of Terminals per Device Common 0 Wire Range (Rated Cross Section) ➋ # # AWG (0. 4mm ) Wire Strip Length Recommended Tightening Torque Operating Temperature Range 0.3 (8mm) lb.-in. ( Nm) 0 C to +60 C ➊ For transients >600V p, use a UL recognized suppression device rated at.5kv withstand. ➋ Maximum number of the same gauge stranded copper conductors allowed per wire funnel: AWG # #0 #8 #6 #4 # No. of Wires Application Notes. Compatibility To ensure proper operation with the I/O module, do not exceed the voltage and current ratings of the IFM. Pinout B B. Wiring Refer to the Label Section on page 74. For Field-Side Wiring Diagrams, refer to Publication (Digital Programmable Controller Wiring Systems Installation Wiring Diagrams) or the Wiring System web page at chassis/49.html. Refer to the online documentation for new product information and for the most up to date set of wiring diagrams B3 B8 B9 B0 3. Isolation The power bus comprises 0 terminals connected together. The LEDs are connected to one common. All of the I/O devices used must reference the same power source. A A 4. Dimensions See page 69. LED Circuit A9 A0 Allen-Bradley Replacements

36 36 Digital Programmable Controller Wiring Systems 49-IFM0D4-3 Specifications Approvals Voltage Rating Maximum Peak Voltage ➊ Maximum Current (per Circuit) Maximum Current (per Module) Indicator Circuit Current (Nominal) UL Component Recognized (File E374 Guide NRAQ) CSA Certified (File LR34 Class 307) CE Approved 0 30V AC/DC 600V p A No. of Terminals per Device Common 8 A ma Wire Range (Rated Cross Section) ➋ # # AWG (0. 4mm ) Wire Strip Length Recommended Tightening Torque Operating Temperature Range 0.3 (8mm) lb.-in. ( Nm) 0 C to +60 C ➊ For transients >600V p, use a UL recognized suppression device rated at.5kv withstand. ➋ Maximum number of the same gauge stranded copper conductors allowed per wire funnel: AWG # #0 #8 #6 #4 # No. of Wires Application Notes. Compatibility To ensure proper operation with the I/O module, do not exceed the voltage and current ratings of the IFM. 3 Pinout C. Wiring Refer to the Label Section on page 74. For Field-Side Wiring Diagrams, refer to Publication (Digital Programmable Controller Wiring Systems Installation Wiring Diagrams) or the Wiring System web page at chassis/49.html. Refer to the online documentation for new product information and for the most up to date set of wiring diagrams. 3. Isolation The LEDs are connected to one common. All of the input devices used must reference the same power source. 4. Dimensions See page C6 B B B7 B8 A A A7 A8 LED Circuit

37 Digital Programmable Controller Wiring Systems IFM0DS4-4 Specifications Approvals Voltage Rating Maximum Peak Voltage ➊ Maximum Current (per Circuit) Maximum Current (per Module) Indicator Circuit Current (Nominal) UL Component Recognized (File E374 Guide NRAQ) UL Recognized per Canadian Safety Standards (cur) (File E374 Guide NRAQ) CE Approved 0 60V AC/DC 600V p A A 4.mA No. of Terminals per Device Common Wire Range (Rated Cross Section) ➋ # # AWG (0. 4mm ) Wire Strip Length Recommended Tightening Torque Operating Temperature Range 0.3 (8mm) lb.-in. ( Nm) 0 C to +60 C ➊ For transients >600V p, use a UL recognized suppression device rated at.5kv withstand. ➋ Maximum number of the same gauge stranded copper conductors allowed per wire funnel: AWG # #0 #8 #6 #4 # No. of Wires Application Notes. Compatibility To ensure proper operation with the I/O module, do not exceed the voltage and current ratings of the IFM.. Wiring Refer to the Label Section on page 74. For Field-Side Wiring Diagrams, refer to Publication (Digital Programmable Controller Wiring Systems Installation Wiring Diagrams) or the Wiring System web page at chassis/49.html. Refer to the online documentation for new product information and for the most up to date set of wiring diagrams. 3. Isolation There are 8 individually isolated channels. LED returns are individually isolated. 4. Extra Terminals Two field side terminals are internally connected on the IFM for each channel, and are available for power source common connections. 5. Dimensions See page 69. Pinout 0 B B B3 (even) 8 B6 B7 (even) 8 B0 3 B (odd) 9 B4 B5 (odd) 7 B8 0 B9 B0 A A A3 A4 A9 A0 A A Allen-Bradley Replacements A7 A8 9 A9 A0

38 38 Digital Programmable Controller Wiring Systems 49-IFM0DS0-4 Specifications Approvals Voltage Rating Maximum Peak Voltage ➊ Maximum Current (per Circuit) Maximum Current (per Module) Indicator Circuit Current (Nominal) UL Component Recognized (File E374 Guide NRAQ) UL Recognized per Canadian Safety Standards (cur) (File E374 Guide NRAQ) CE Approved 85 3V AC 600V p A A.6mA No. of Terminals per Device Common Wire Range (Rated Cross Section) ➋ # # AWG (0. 4mm ) Wire Strip Length Recommended Tightening Torque Operating Temperature Range 0.3 (8mm) lb.-in. ( Nm) 0 C to +60 C ➊ For transients >600V p, use a UL recognized suppression device rated at.5kv withstand. ➋ Maximum number of the same gauge stranded copper conductors allowed per wire funnel: AWG # #0 #8 #6 #4 # No. of Wires Application Notes. Compatibility To ensure proper operation with the I/O module, do not exceed the voltage and current ratings of the IFM.. Wiring Refer to the Label Section on page 74. For Field-Side Wiring Diagrams, refer to Publication (Digital Programmable Controller Wiring Systems Installation Wiring Diagrams) or the Wiring System web page at chassis/49.html. Refer to the online documentation for new product information and for the most up to date set of wiring diagrams. 3. Isolation There are 8 individually isolated channels. LED returns are individually isolated. 4. Extra Terminals Two field side terminals are internally connected on the IFM for each channel, and are available for power source common connections. 5. Dimensions See page 69. Pinout 0 B B B3 (even) 8 B6 B7 (even) 8 B0 3 B (odd) 9 B4 B5 (odd) 7 B8 0 B9 B0 A A A3 A4 A9 A0 A A 9 A7 A8 A9 A0

39 Digital Programmable Controller Wiring Systems IFM0F-F- Specifications Approvals Voltage Rating Maximum Peak Voltage ➊ Maximum Current (per Circuit) Maximum Current (per Module) Indicator Circuit Current (Nominal) UL Component Recognized (File E374 Guide NRAQ) CSA Certified (File LR34 Class 307) CE Approved 0 3V AC/DC 600V p A No. of Terminals per Device Common 0 Wire Range (Rated Cross Section) ➋ # # AWG (0. 4mm ) Wire Strip Length Recommended Tightening Torque Operating Temperature Range A NA 0.3 (8mm) lb.-in. ( Nm) 0 C to +60 C ➊ For transients >600V p, use a UL recognized suppression device rated at.5kv withstand. ➋ Maximum number of the same gauge stranded copper conductors allowed per wire funnel: AWG # #0 #8 #6 #4 # No. of Wires Application Notes. Compatibility To ensure proper operation with the I/O module, do not exceed the voltage and current ratings of the IFM. 3 Pinout B B B3. Wiring Refer to the Label Section on page 74. For Field-Side Wiring Diagrams, refer to Publication (Digital Programmable Controller Wiring Systems Installation Wiring Diagrams) or the Wiring System web page at chassis/49.html. Refer to the online documentation for new product information and for the most up to date set of wiring diagrams A A A A B8 B9 B0 3. Fusing Twenty fuse holders are included with the IFM. Fuses (5 x 0mm) are not included. 4. Isolation The power bus and fuse clips are isolated into groups of 0 terminals (8 fuse clips). This allows each group of output devices to reference a different power source. A9 A0 A9 A0 5. Dimensions See page 69. Allen-Bradley Replacements

40 40 Digital Programmable Controller Wiring Systems 49-IFM0F-F4- Specifications Approvals Voltage Rating Maximum Peak Voltage ➊ Maximum Current (per Circuit) Maximum Current (per Module) Indicator Circuit Current (Nominal) UL Component Recognized (File E374 Guide NRAQ) CSA Certified (File LR34 Class 307) CE Approved 0 30V AC/DC 600V p A No. of Terminals per Device Common 0 A ma Wire Range (Rated Cross Section) ➋ # # AWG (0. 4mm ) Wire Strip Length Recommended Tightening Torque Operating Temperature Range 0.3 (8mm) lb.-in. ( Nm) 0 C to +60 C ➊ For transients >600V p, use a UL recognized suppression device rated at.5kv withstand. ➋ Maximum number of the same gauge stranded copper conductors allowed per wire funnel: AWG # #0 #8 #6 #4 # No. of Wires Application Notes. Compatibility To ensure proper operation with the I/O module, do not exceed the voltage and current ratings of the IFM. When this IFM is used with a hard contact (relay) output circuit that switches an inductive load, surge suppression must be used (i.e., a N4004 diode reverse wired across a DC load).. Wiring Refer to the Label Section on page 74. For Field-Side Wiring Diagrams, refer to Publication (Digital Programmable Controller Wiring Systems Installation Wiring Diagrams) or the Wiring System web page at chassis/49.html. Refer to the online documentation for new product information and for the most up to date set of wiring diagrams A A A9 A0 Pinout A A A9 A0 B B B3 B8 B9 B0 3. Fusing Twenty fuse holders are included with the IFM. Fuses (5 x 0mm) are not included. 4. Isolation The power bus, fuse clips, and blown fuse indicators are isolated into groups of 0 terminals (8 fuse clips and blown fuse indicators). This allows each group of output devices to reference a different power source. 5. Dimensions See page 69. Blown Fuse Indicator Circuit

41 Digital Programmable Controller Wiring Systems 4 49-IFM0F-F4A- Specifications Approvals Voltage Rating Maximum Peak Voltage ➊ Maximum Current (per Circuit) Maximum Current (per Module) Indicator Circuit Current (Nominal) UL Component Recognized (File E374 Guide NRAQ) CSA Certified (File LR34 Class 307) CE Approved 0 30V AC/DC 600V p A No. of Terminals per Device Common 0 A ma Wire Range (Rated Cross Section) ➋ # # AWG (0. 4mm ) Wire Strip Length Recommended Tightening Torque Operating Temperature Range 0.3 (8mm) lb.-in. ( Nm) 0 C to +60 C ➊ For transients >600V p, use a UL recognized suppression device rated at.5kv withstand. ➋ Maximum number of the same gauge stranded copper conductors allowed per wire funnel: AWG # #0 #8 #6 #4 # No. of Wires Application Notes. Compatibility To ensure proper operation with the I/O module, do not exceed the voltage and current ratings of the IFM.. Wiring Refer to the Label Section on page 74. For Field-Side Wiring Diagrams, refer to Publication (Digital Programmable Controller Wiring Systems Installation Wiring Diagrams) or the Wiring System web page at chassis/49.html. Refer to the online documentation for new product information and for the most up to date set of wiring diagrams. 3. Fusing Twenty fuse holders are included with the IFM. Fuses (5 x 0mm) are not included. 4. Isolation The power bus, fuse clips, and blown fuse indicators are isolated into groups of 0 terminals (8 fuse clips and blown fuse indicators). This allows each group of input or output devices to reference a different power source. 5. Dimensions See page Blown Fuse Indicator Circuit Pinout B B B3 B8 B9 B0 A A A3 A0 A A8 A9 A0 Allen-Bradley Replacements

42 4 Digital Programmable Controller Wiring Systems 49-IFM0F-F0- Specifications Approvals Voltage Rating Maximum Peak Voltage ➊ Maximum Current (per Circuit) Maximum Current (per Module) Indicator Circuit Current (Nominal) UL Component Recognized (File E374 Guide NRAQ) CSA Certified (File LR34 Class 307) CE Approved 85 3V AC 600V p A A.5mA No. of Terminals per Device Common 0 Wire Range (Rated Cross Section) ➋ # # AWG (0. 4mm ) Wire Strip Length Recommended Tightening Torque Operating Temperature Range 0.3 (8mm) lb.-in. ( Nm) 0 C to +60 C ➊ For transients >600V p, use a UL recognized suppression device rated at.5kv withstand. ➋ Maximum number of the same gauge stranded copper conductors allowed per wire funnel: AWG # #0 #8 #6 #4 # No. of Wires Application Notes. Compatibility To ensure proper operation with the I/O module, do not exceed the voltage and current ratings of the IFM. When this IFM is used with a hard contact (relay) output circuit that switches an inductive load, surge suppression must be used (i.e., a N4004 diode reverse wired across a DC load).. Wiring Refer to the Label Section on page 74. For Field-Side Wiring Diagrams, refer to Publication (Digital Programmable Controller Wiring Systems Installation Wiring Diagrams) or the Wiring System web page at chassis/49.html. Refer to the online documentation for new product information and for the most up to date set of wiring diagrams A A A9 A0 Pinout A A A9 A0 B B B3 B8 B9 B0 3. Fusing Twenty fuse holders are included with the IFM. Fuses (5 x 0mm) are not included. 4. Isolation The power bus, fuse clips, and blown fuse indicators are isolated into groups of 0 terminals (8 fuse clips and blown fuse indicators). This allows each group of output devices to reference a different power source. 5. Dimensions See page 69. Blown Fuse Indicator Circuit

43 Digital Programmable Controller Wiring Systems IFM0F-F0A- Specifications Approvals Voltage Rating Maximum Peak Voltage ➊ Maximum Current (per Circuit) Maximum Current (per Module) Indicator Circuit Current (Nominal) UL Component Recognized (File E374 Guide NRAQ) UL Recognized per Canadian Safety Standards (cur) (File E374 Guide NRAQ) CE Approved 85 3V AC/DC 600V p A A.mA No. of Terminals per Device Common 0 Wire Range (Rated Cross Section) ➋ # # AWG (0. 4mm ) Wire Strip Length Recommended Tightening Torque Operating Temperature Range 0.3 (8mm) lb.-in. ( Nm) 0 C to +60 C ➊ For transients >600V p, use a UL recognized suppression device rated at.5kv withstand. ➋ Maximum number of the same gauge stranded copper conductors allowed per wire funnel: AWG # #0 #8 #6 #4 # No. of Wires Application Notes. Compatibility To ensure proper operation with the I/O module, do not exceed the voltage and current ratings of the IFM.. Wiring Refer to the Label Section on page 74. For Field-Side Wiring Diagrams, refer to Publication (Digital Programmable Controller Wiring Systems Installation Wiring Diagrams) or the Wiring System web page at chassis/49.html. Refer to the online documentation for new product information and for the most up to date set of wiring diagrams. 3. Fusing Twenty fuse holders are included with the IFM. Fuses (5 x 0mm) are not included. 4. Isolation The power bus, fuse clips, and blown fuse indicators are isolated into groups of 0 terminals (8 fuse clips and blown fuse indicators). This allows each group of input devices to reference a different power source. 5. Dimensions See page Blown Fuse Indicator Circuit Pinout B B B3 B8 B9 B0 A A A3 A0 A A8 A9 A0 Allen-Bradley Replacements

44 44 Digital Programmable Controller Wiring Systems 49-IFM0F-FS- Specifications Approvals Voltage Rating Maximum Peak Voltage ➊ Maximum Current (per Circuit) Maximum Current (per Module) Indicator Circuit Current (Nominal) UL Component Recognized (File E374 Guide NRAQ) UL Recognized per Canadian Safety Standards (cur) (File E374 Guide NRAQ) CE Approved 0 3V AC/DC 600V p A No. of Terminals per Device Common Wire Range (Rated Cross Section) ➋ # # AWG (0. 4mm ) Wire Strip Length Recommended Tightening Torque Operating Temperature Range A NA 0.3 (8mm) lb.-in. ( Nm) 0 C to +60 C ➊ For transients >600V p, use a UL recognized suppression device rated at.5kv withstand. ➋ Maximum number of the same gauge stranded copper conductors allowed per wire funnel: AWG # #0 #8 #6 #4 # No. of Wires Application Notes. Compatibility To ensure proper operation with the I/O module, do not exceed the voltage and current ratings of the IFM.. Wiring Refer to the Label Section on page 74. For Field-Side Wiring Diagrams, refer to Publication (Digital Programmable Controller Wiring Systems Installation Wiring Diagrams) or the Wiring System web page at chassis/49.html. Refer to the online documentation for new product information and for the most up to date set of wiring diagrams. 3. Fusing Ten fuse holders are included with the IFM. Fuses (5 x 0mm) are not included. 4. Isolation The fuse clips are isolated into 8 groups of terminals. This allows each group of output devices to reference a different power source. 5. Dimensions See page 69. Pinout 0 B 3 B 5 B3 (odd) 5 B8 7 B9 0 B0 A A 4 A3 6 A4 8 A5 A6 4 A7 6 A8 8 A9 9 A0

45 Digital Programmable Controller Wiring Systems IFM0F-FS4- Specifications Approvals Voltage Rating Maximum Peak Voltage ➊ Maximum Current (per Circuit) Maximum Current (per Module) Indicator Circuit Current (Nominal) UL Component Recognized (File E374 Guide NRAQ) UL Recognized per Canadian Safety Standards (cur) (File E374 Guide NRAQ) CE Approved 0 30V AC/DC 600V p A No. of Terminals per Device Common A ma Wire Range (Rated Cross Section) ➋ # # AWG (0. 4mm ) Wire Strip Length Recommended Tightening Torque Operating Temperature Range 0.3 (8mm) lb.-in. ( Nm) 0 C to +60 C ➊ For transients >600V p, use a UL recognized suppression device rated at.5kv withstand. ➋ Maximum number of the same gauge stranded copper conductors allowed per wire funnel: AWG # #0 #8 #6 #4 # No. of Wires Application Notes. Compatibility To ensure proper operation with the I/O module, do not exceed the voltage and current ratings of the IFM. When this IFM is used with a hard contact (relay) output circuit that switches an inductive load, surge suppression must be used (i.e., a N4004 diode reverse wired across a DC load).. Wiring Refer to the Label Section on page 74. For Field-Side Wiring Diagrams, refer to Publication (Digital Programmable Controller Wiring Systems Installation Wiring Diagrams) or the Wiring System web page at chassis/49.html. Refer to the online documentation for new product information and for the most up to date set of wiring diagrams. 3. Fusing Ten fuse holders are included with the IFM. Fuses (5 x 0mm) are not included. 4. Isolation The fuse clips and blown fuse indicators are isolated into 8 groups of terminals. This allows each group of output devices to reference a different power source. 5. Dimensions See page 69. Pinout 0 B 3 B 5 B3 (odd) 5 B8 7 B9 0 B0 A A 4 A3 6 A4 8 A5 A6 4 A7 6 A8 8 A9 9 A0 Blown Fuse Indicator Circuit Allen-Bradley Replacements

46 46 Digital Programmable Controller Wiring Systems 49-IFM0F-FS0- Specifications Approvals Voltage Rating Maximum Peak Voltage ➊ Maximum Current (per Circuit) Maximum Current (per Module) Indicator Circuit Current (Nominal) UL Component Recognized (File E374 Guide NRAQ) UL Recognized per Canadian Safety Standards (cur) (File E374 Guide NRAQ) CE Approved 85 3V AC/DC 600V p A A.5mA No. of Terminals per Device Common Wire Range (Rated Cross Section) ➋ # # AWG (0. 4mm ) Wire Strip Length Recommended Tightening Torque Operating Temperature Range 0.3 (8mm) lb.-in. ( Nm) 0 C to +60 C ➊ For transients >600V p, use a UL recognized suppression device rated at.5kv withstand. ➋ Maximum number of the same gauge stranded copper conductors allowed per wire funnel: AWG # #0 #8 #6 #4 # No. of Wires Application Notes. Compatibility To ensure proper operation with the I/O module, do not exceed the voltage and current ratings of the IFM. When this IFM is used with a hard contact (relay) output circuit that switches an inductive load, surge suppression must be used (i.e., a N4004 diode reverse wired across a DC load).. Wiring Refer to the Label Section on page 74. For Field-Side Wiring Diagrams, refer to Publication (Digital Programmable Controller Wiring Systems Installation Wiring Diagrams) or the Wiring System web page at chassis/49.html. Refer to the online documentation for new product information and for the most up to date set of wiring diagrams. 3. Fusing Ten fuse holders are included with the IFM. Fuses (5 x 0mm) are not included. 4. Isolation The fuse clips and blown fuse indicators are isolated into 8 groups of terminals. This allows each group of output devices to reference a different power source. 5. Dimensions See page 69. Pinout 0 B 3 B 5 B3 (odd) 5 B8 7 B9 0 B0 A A 4 A3 6 A4 8 A5 A6 4 A7 6 A8 8 A9 9 A0 Blown Fuse Indicator Circuit

47 Digital Programmable Controller Wiring Systems IFM40F Specifications Approvals Voltage Rating Maximum Peak Voltage ➊ Maximum Current (per Circuit) Maximum Current (per Module) Indicator Circuit Current (Nominal) No. of Terminals per Device Common UL Component Recognized (File E374 Guide NRAQ) CSA Certified (File LR34 Class 307) CE Approved 0 3V AC/DC 600V p A Wire Range (Rated Cross Section) ➋ # # AWG (0. 4mm ) Wire Strip Length Recommended Tightening Torque Operating Temperature Range A NA NA 0.3 (8mm) lb.-in. ( Nm) 0 C to +60 C ➊ For transients >600V p, use a UL recognized suppression device rated at.5kv withstand. ➋ Maximum number of the same gauge stranded copper conductors allowed per wire funnel: AWG # #0 #8 #6 #4 # No. of Wires Application Notes. Compatibility To ensure proper operation with the I/O module, do not exceed the voltage and current ratings of the IFM. 3 5 Pinout A A A3. Wiring Refer to the Label Section on page 74. For Field-Side Wiring Diagrams, refer to Publication (Digital Programmable Controller Wiring Systems Installation Wiring Diagrams) or the Wiring System web page at chassis/49.html. Refer to the online documentation for new product information and for the most up to date set of wiring diagrams. 3. Dimensions See page 69. (odd) A8 A9 A0 B B B3 (even) 36 B8 38 B9 40 B0 Allen-Bradley Replacements

48 48 Digital Programmable Controller Wiring Systems 49-IFM40F- Specifications Approvals Voltage Rating Maximum Peak Voltage ➊ Maximum Current (per Circuit) Maximum Current (per Module) Indicator Circuit Current (Nominal) UL Component Recognized (File E374 Guide NRAQ) CSA Certified (File LR34 Class 307) CE Approved 0 3V DC 600V p A No. of Terminals per Device Common 0 Wire Range (Rated Cross Section) ➋ # # AWG (0. 4mm ) Wire Strip Length Recommended Tightening Torque Operating Temperature Range A NA 0.3 (8mm) lb.-in. ( Nm) 0 C to +60 C ➊ For transients >600V p, use a UL recognized suppression device rated at.5kv withstand. ➋ Maximum number of the same gauge stranded copper conductors allowed per wire funnel: AWG # #0 #8 #6 #4 # No. of Wires Application Notes. Compatibility To ensure proper operation with the I/O module, do not exceed the voltage and current ratings of the IFM. 3 5 Pinout B B B3. Wiring Refer to the Label Section on page 74. For Field-Side Wiring Diagrams, refer to Publication (Digital Programmable Controller Wiring Systems Installation Wiring Diagrams) or the Wiring System web page at chassis/49.html. Refer to the online documentation for new product information and for the most up to date set of wiring diagrams. 3. Isolation The power bus is isolated into 4 groups of 0 terminals. This allows each group of the I/O devices to reference a different power source. 4. Dimensions See page 69. (odd) (even) B8 B9 B0 B B B3 B38 B39 40 B40 A A A A3 A A A A3 A9 A9 A9 A39 A0 A0 A30 A40

49 Digital Programmable Controller Wiring Systems IFM40F-3 TB TB Specifications Approvals Voltage Rating Maximum Peak Voltage ➊ Maximum Current (per Circuit) Maximum Current (per Module) Indicator Circuit Current (Nominal) UL Component Recognized (File E374 Guide NRAQ) CSA Certified (File LR34 Class 307) CE Approved 0 60V AC/DC 600V p A No. of Terminals per Device Common 8 Wire Range (Rated Cross Section) ➋ # # AWG (0. 4mm ) Wire Strip Length Recommended Tightening Torque Operating Temperature Range A NA 0.3 (8mm) lb.-in. ( Nm) 0 C to +60 C ➊ For transients >600V p, use a UL recognized suppression device rated at.5kv withstand. ➋ Maximum number of the same gauge stranded copper conductors allowed per wire funnel: AWG # #0 #8 #6 #4 # No. of Wires Application Notes. Compatibility To ensure proper operation with the I/O module, do not exceed the voltage and current ratings of the IFM.. Wiring Refer to the Label Section on page 74. For Field-Side Wiring Diagrams, refer to Publication (Digital Programmable Controller Wiring Systems Installation Wiring Diagrams) or the Wiring System web page at chassis/49.html. Refer to the online documentation for new product information and for the most up to date set of wiring diagrams. 3. Isolation The power busses are isolated into groups of 8 terminals. This allows the input devices connected to the left field side terminal block to reference a different power source than the input devices connected to the right field side terminal block. 4. Dimensions See page (odd) Pinout TB C C6 B B B7 B8 A A A7 A8 TB C (even) 36 C6 4 B B B7 B8 A A Allen-Bradley Replacements A7 A8

50 50 Digital Programmable Controller Wiring Systems 49-IFM40D4 Specifications Approvals Voltage Rating Maximum Peak Voltage ➊ Maximum Current (per Circuit) Maximum Current (per Module) Indicator Circuit Current (Nominal) UL Component Recognized (File E374 Guide NRAQ) CSA Certified (File LR34 Class 307) CE Approved 0 30V AC/DC 600V p A No. of Terminals per Device Common 3 A ma Wire Range (Rated Cross Section) ➋ # # AWG (0. 4mm ) Wire Strip Length Recommended Tightening Torque Operating Temperature Range 0.3 (8mm) lb.-in. ( Nm) 0 C to +60 C ➊ For transients >600V p, use a UL recognized suppression device rated at.5kv withstand. ➋ Maximum number of the same gauge stranded copper conductors allowed per wire funnel: AWG # #0 #8 #6 #4 # No. of Wires Application Notes. Compatibility To ensure proper operation with the I/O module, do not exceed the voltage and current ratings of the IFM. When this IFM is used with a hard contact (relay) output circuit that switches an inductive load, surge suppression must be used (i.e., a N4004 diode reverse wired across a DC load).. Wiring Refer to the Label Section on page 74. For Field-Side Wiring Diagrams, refer to Publication (Digital Programmable Controller Wiring Systems Installation Wiring Diagrams) or the Wiring System web page at chassis/49.html. Refer to the online documentation for new product information and for the most up to date set of wiring diagrams. The LEDs are powered off the position terminal block. Make only one connection to the power source for normal operation. The test push button and wiring connection are only used to test the LEDs. 3 5 (odd) Pinout A A A3 A8 A9 A0 L (+) L ( ) 3. Isolation The LEDs are connected to one common. All of the I/O devices used must reference the same power source. 4. Dimensions See page (even) B B B B8 B9 B0

51 Digital Programmable Controller Wiring Systems 5 49-IFM40D4- Specifications Approvals Voltage Rating Maximum Peak Voltage ➊ Maximum Current (per Circuit) Maximum Current (per Module) Indicator Circuit Current (Nominal) UL Component Recognized (File E374 Guide NRAQ) CSA Certified (File LR34 Class 307) CE Approved 0 30V AC/DC 600V p A No. of Terminals per Device Common 0 A ma Wire Range (Rated Cross Section) ➋ # # AWG (0. 4mm ) Wire Strip Length Recommended Tightening Torque Operating Temperature Range 0.3 (8mm) lb.-in. ( Nm) 0 C to +60 C ➊ For transients >600V p, use a UL recognized suppression device rated at.5kv withstand. ➋ Maximum number of the same gauge stranded copper conductors allowed per wire funnel: AWG # #0 #8 #6 #4 # No. of Wires Application Notes. Compatibility To ensure proper operation with the I/O module, do not exceed the voltage and current ratings of the IFM. When this IFM is used with a hard contact (relay) output circuit that switches an inductive load, surge suppression must be used (i.e., a N4004 diode reverse wired across a DC load).. Wiring Refer to the Label Section on page 74. For Field-Side Wiring Diagrams, refer to Publication (Digital Programmable Controller Wiring Systems Installation Wiring Diagrams) or the Wiring System web page at chassis/49.html. Refer to the online documentation for new product information and for the most up to date set of wiring diagrams. 3. Isolation The power bus and LEDs are isolated into 4 groups of 0 terminals (8 LEDs). This allows each group of output devices to reference a different power source. 4. Dimensions See page (odd) 9 (odd) (even) 0 Pinout A A A9 A0 B B B3 B0 B B8 B9 B0 A A A9 A0 B B B3 B30 (even) B B38 B39 B40 A A3 A A3 Allen-Bradley Replacements A9 A39 A30 A40 LED Circuit

52 5 Digital Programmable Controller Wiring Systems 49-IFM40D4A- Specifications Approvals Voltage Rating Maximum Peak Voltage ➊ Maximum Current (per Circuit) Maximum Current (per Module) Indicator Circuit Current (Nominal) UL Component Recognized (File E374 Guide NRAQ) CSA Certified (File LR34 Class 307) CE Approved 0 30V AC/DC 600V p A No. of Terminals per Device Common 0 A ma Wire Range (Rated Cross Section) ➋ # # AWG (0. 4mm ) Wire Strip Length Recommended Tightening Torque Operating Temperature Range 0.3 (8mm) lb.-in. ( Nm) 0 C to +60 C ➊ For transients >600V p, use a UL recognized suppression device rated at.5kv withstand. ➋ Maximum number of the same gauge stranded copper conductors allowed per wire funnel: AWG # #0 #8 #6 #4 # No. of Wires Application Notes. Compatibility To ensure proper operation with the I/O module, do not exceed the voltage and current ratings of the IFM. 3 5 Pinout B B B3. Wiring Refer to the Label Section on page 74. For Field-Side Wiring Diagrams, refer to Publication (Digital Programmable Controller Wiring Systems Installation Wiring Diagrams) or the Wiring System web page at chassis/49.html. Refer to the online documentation for new product information and for the most up to date set of wiring diagrams. 3. Isolation The power bus and LEDs are isolated into 4 groups of 0 terminals (8 LEDs). This allows each group of input devices to reference a different power source. 4. Dimensions See page 69. (odd) 9 (odd) A A A9 A0 A A A9 A0 B0 B B8 B9 B0 B 4 B 6 B3 (even) 0 B30 B3 (even) 36 B38 38 B39 40 B40 A A3 A A3 A9 A39 A30 A40 LED Circuit

53 Digital Programmable Controller Wiring Systems IFM40D0- Specifications Approvals Voltage Rating Maximum Peak Voltage ➊ Maximum Current (per Circuit) Maximum Current (per Module) Indicator Circuit Current (Nominal) UL Component Recognized (File E374 Guide NRAQ) CSA Certified (File LR34 Class 307) CE Approved 85 3V AC 600V p A A.5mA No. of Terminals per Device Common 0 Wire Range (Rated Cross Section) ➋ # # AWG (0. 4mm ) Wire Strip Length Recommended Tightening Torque Operating Temperature Range 0.3 (8mm) lb.-in. ( Nm) 0 C to +60 C ➊ For transients >600V p, use a UL recognized suppression device rated at.5kv withstand. ➋ Maximum number of the same gauge stranded copper conductors allowed per wire funnel: AWG # #0 #8 #6 #4 # No. of Wires Application Notes. Compatibility To ensure proper operation with the I/O module, do not exceed the voltage and current ratings of the IFM. When this IFM is used with a hard contact (relay) output circuit that switches an inductive load, surge suppression must be used (i.e., a N4004 diode reverse wired across a DC load).. Wiring Refer to the Label Section on page 74. For Field-Side Wiring Diagrams, refer to Publication (Digital Programmable Controller Wiring Systems Installation Wiring Diagrams) or the Wiring System web page at chassis/49.html. Refer to the online documentation for new product information and for the most up to date set of wiring diagrams. 3. Isolation The power bus and LEDs are isolated into 4 groups of 0 terminals (8 LEDs). This allows each group of output devices to reference a different power source. 4. Dimensions See page (odd) 9 (odd) (even) 0 Pinout A A A9 A0 B B B3 B0 B B8 B9 B0 A A A9 A0 B B B3 B30 (even) B B38 B39 B40 A A3 A A3 Allen-Bradley Replacements A9 A39 A30 A40 LED Circuit

54 54 Digital Programmable Controller Wiring Systems 49-IFM40D0A- Specifications Approvals Voltage Rating Maximum Peak Voltage ➊ Maximum Current (per Circuit) Maximum Current (per Module) Indicator Circuit Current (Nominal) UL Component Recognized (File E374 Guide NRAQ) CSA Certified (File LR34 Class 307) CE Approved 85 3V AC 600V p A A.5mA No. of Terminals per Device Common 0 Wire Range (Rated Cross Section) ➋ # # AWG (0. 4mm ) Wire Strip Length Recommended Tightening Torque Operating Temperature Range 0.3 (8mm) lb.-in. ( Nm) 0 C to +60 C ➊ For transients >600V p, use a UL recognized suppression device rated at.5kv withstand. ➋ Maximum number of the same gauge stranded copper conductors allowed per wire funnel: AWG # #0 #8 #6 #4 # No. of Wires Application Notes. Compatibility To ensure proper operation with the I/O module, do not exceed the voltage and current ratings of the IFM. 3 5 Pinout B B B3. Wiring Refer to the Label Section on page 74. For Field-Side Wiring Diagrams, refer to Publication (Digital Programmable Controller Wiring Systems Installation Wiring Diagrams) or the Wiring System web page at chassis/49.html. Refer to the online documentation for new product information and for the most up to date set of wiring diagrams. 3. Isolation The power bus and LEDs are isolated into 4 groups of 0 terminals (8 LEDs). This allows each group of input devices to reference a different power source. 4. Dimensions See page 69. (odd) 9 (odd) A A A9 A0 A A A9 A0 B0 B B8 B9 B0 B 4 B 6 B3 (even) 0 B30 B3 (even) 36 B38 38 B39 40 B40 A A3 A A3 A9 A39 A30 A40 LED Circuit

55 Digital Programmable Controller Wiring Systems IFM40D4-3 TB TB Specifications Approvals Voltage Rating Maximum Peak Voltage ➊ Maximum Current (per Circuit) Maximum Current (per Module) Indicator Circuit Current (Nominal) UL Component Recognized (File E374 Guide NRAQ) CSA Certified (File LR34 Class 307) CE Approved 0 30V AC/DC 600V p A No. of Terminals per Device Common 8 A ma Wire Range (Rated Cross Section) ➋ # # AWG (0. 4mm ) Wire Strip Length Recommended Tightening Torque Operating Temperature Range 0.3 (8mm) lb.-in. ( Nm) 0 C to +60 C ➊ For transients >600V p, use a UL recognized suppression device rated at.5kv withstand. ➋ Maximum number of the same gauge stranded copper conductors allowed per wire funnel: AWG # #0 #8 #6 #4 # No. of Wires Application Notes. Compatibility To ensure proper operation with the I/O module, do not exceed the voltage and current ratings of the IFM. 5 (odd) Pinout TB C. Wiring Refer to the Label Section on page 74. For Field-Side Wiring Diagrams, refer to Publication (Digital Programmable Controller Wiring Systems Installation Wiring Diagrams) or the Wiring System web page at chassis/49.html. Refer to the online documentation for new product information and for the most up to date set of wiring diagrams. 3. Isolation The power busses and LEDs are isolated into groups of 8 terminals (6 LEDs). This allows the input devices connected to the left field side terminal block to reference a different power source than the input devices connected to the right field side terminal block. 4. Dimensions See page (even) C6 B B B7 B8 A A A7 A8 TB C 36 C6 4 B B B7 B8 A Allen-Bradley Replacements A A7 A8 LED Circuit

56 56 Digital Programmable Controller Wiring Systems 49-IFM40DS4-4 Specifications Approvals Voltage Rating Maximum Peak Voltage ➊ Maximum Current (per Circuit) Maximum Current (per Module) Indicator Circuit Current UL Component Recognized (File E374 Guide NRAQ) UL Recognized per Canadian Safety Standards (cur) (File E374 Guide NRAQ) CE Approved 0 60V AC/DC 600V p A A 4.mA No. of Terminals per Device Common Wire Range (Rated Cross Section) ➋ # # AWG (0. 4mm ) Wire Strip Length Recommended Tightening Torque Operating Temperature Range 0.3 (8mm) lb.-in. ( Nm) 0 C to +60 C ➊ For transients >600V p, use a UL recognized suppression device rated at.5kv withstand. ➋ Maximum number of the same gauge stranded copper conductors allowed per wire funnel: AWG # #0 #8 #6 #4 # No. of Wires Application Notes. Compatibility To ensure proper operation with the I/O module, do not exceed the voltage and current ratings of the IFM.. Wiring Refer to the Label Section on page 74. For Field-Side Wiring Diagrams, refer to Publication (Digital Programmable Controller Wiring Systems Installation Wiring Diagrams) or the Wiring System web page at chassis/49.html. Refer to the online documentation for new product information and for the most up to date set of wiring diagrams. 3. Isolation There are 6 individually isolated channels. LED returns are individually isolated. 4. Extra Terminals Two field-side terminals are internally connected on the IFM for each channel, and are available for power source common connections. 5. Dimensions See page 69. Pinout 5 B (odd) 9 B8 B5 (odd) 35 B3 6 B9 (even) 0 B6 B7 (even) 36 B4 A A A5 A6 A7 A8 A3 A3

57 Digital Programmable Controller Wiring Systems IFM40DS4A-4 Specifications Approvals Voltage Rating Maximum Peak Voltage ➊ Maximum Current (per Circuit) Maximum Current (per Module) Indicator Circuit Current UL Component Recognized (File E374 Guide NRAQ) UL Recognized per Canadian Safety Standards (cur) (File E374 Guide NRAQ) CE Approved 0 30V AC/DC 600V p A A 4.mA No. of Terminals per Device Common Wire Range (Rated Cross Section) ➋ # # AWG (0. 4mm ) Wire Strip Length Recommended Tightening Torque Operating Temperature Range 0.3 (8mm) lb.-in. ( Nm) 0 C to +60 C ➊ For transients >600V p, use a UL recognized suppression device rated at.5kv withstand. ➋ Maximum number of the same gauge stranded copper conductors allowed per wire funnel: AWG # #0 #8 #6 #4 # No. of Wires Application Notes. Compatibility To ensure proper operation with the I/O module, do not exceed the voltage and current ratings of the IFM.. Wiring Refer to the Label Section on page 74. For Field-Side Wiring Diagrams, refer to Publication (Digital Programmable Controller Wiring Systems Installation Wiring Diagrams) or the Wiring System web page at chassis/49.html. Refer to the online documentation for new product information and for the most up to date set of wiring diagrams. 3. Isolation There are 6 individually isolated channels. LED returns are individually isolated. 4. Extra Terminals Two field-side terminals are internally connected on the IFM for each channel, and are available for power source common connections. 5. Dimensions See page 69. Pinout 6 B9 (even) 0 B6 5 B (odd) 9 B8 B7 (even) 36 B4 B5 (odd) 35 B3 A A A3 Allen-Bradley Replacements A3

58 58 Digital Programmable Controller Wiring Systems 49-IFM40DS0-4 Specifications Approvals Voltage Rating Maximum Peak Voltage ➊ Maximum Current (per Circuit) Maximum Current (per Module) Indicator Circuit Current UL Component Recognized (File E374 Guide NRAQ) UL Recognized per Canadian Safety Standards (cur) (File E374 Guide NRAQ) CE Approved 85 3V AC 600V p A A.6mA No. of Terminals per Device Common Wire Range (Rated Cross Section) ➋ # # AWG (0. 4mm ) Wire Strip Length Recommended Tightening Torque Operating Temperature Range 0.3 (8mm) lb.-in. ( Nm) 0 C to +60 C ➊ For transients >600V p, use a UL recognized suppression device rated at.5kv withstand. ➋ Maximum number of the same gauge stranded copper conductors allowed per wire funnel: AWG # #0 #8 #6 #4 # No. of Wires Application Notes. Compatibility To ensure proper operation with the I/O module, do not exceed the voltage and current ratings of the IFM.. Wiring Refer to the Label Section on page 74. For Field-Side Wiring Diagrams, refer to Publication (Digital Programmable Controller Wiring Systems Installation Wiring Diagrams) or the Wiring System web page at chassis/49.html. Refer to the online documentation for new product information and for the most up to date set of wiring diagrams. 3. Isolation There are 6 individually isolated channels. LED returns are individually isolated. 4. Extra Terminals Two field-side terminals are internally connected on the IFM for each channel, and are available for power source common connections. 5. Dimensions See page 69. Pinout 0 B B B3 (even) 8 B6 B7 (even) 8 B0 3 B (odd) 9 B4 B5 (odd) 7 B8 0 B9 B0 A A A3 A4 A9 A0 A A 9 A7 A8 A9 A0

59 Digital Programmable Controller Wiring Systems IFM40DS0A-4 Specifications Approvals Voltage Rating Maximum Peak Voltage ➊ Maximum Current (per Circuit) Maximum Current (per Module) Indicator Circuit Current UL Component Recognized (File E374 Guide NRAQ) UL Recognized per Canadian Safety Standards (cur) (File E374 Guide NRAQ) CE Approved 85 3V AC 600V p A A.6mA No. of Terminals per Device Common Wire Range (Rated Cross Section) ➋ # # AWG (0. 4mm ) Wire Strip Length Recommended Tightening Torque Operating Temperature Range 0.3 (8mm) lb.-in. ( Nm) 0 C to +60 C ➊ For transients >600V p, use a UL recognized suppression device rated at.5kv withstand. ➋ Maximum number of the same gauge stranded copper conductors allowed per wire funnel: AWG # #0 #8 #6 #4 # No. of Wires Application Notes. Compatibility To ensure proper operation with the I/O module, do not exceed the voltage and current ratings of the IFM.. Wiring Refer to the Label Section on page 74. For Field-Side Wiring Diagrams, refer to Publication (Digital Programmable Controller Wiring Systems Installation Wiring Diagrams) or the Wiring System web page at chassis/49.html. Refer to the online documentation for new product information and for the most up to date set of wiring diagrams. 3. Isolation There are 6 individually isolated channels. LED returns are individually isolated. 4. Extra Terminals Two field-side terminals are internally connected on the IFM for each channel, and are available for power source common connections. 5. Dimensions See page 69. Pinout 6 B9 (even) 0 B6 5 B (odd) 9 B8 B7 (even) 36 B4 B5 (odd) 35 B3 A A A3 Allen-Bradley Replacements A3

60 60 Digital Programmable Controller Wiring Systems 49-IFM40F-F- Specifications Approvals Voltage Rating Maximum Peak Voltage ➊ Maximum Current (per Circuit) Maximum Current (per Module) Indicator Circuit Current (Nominal) UL Component Recognized (File E374 Guide NRAQ) CSA Certified (File LR34 Class 307) CE Approved 0 3V AC/DC 600V p A No. of Terminals per Device Common 0 Wire Range (Rated Cross Section) ➋ # # AWG (0. 4mm ) Wire Strip Length Recommended Tightening Torque Operating Temperature Range A NA 0.3 (8mm) lb.-in. ( Nm) 0 C to +60 C ➊ For transients >600V p, use a UL recognized suppression device rated at.5kv withstand. ➋ Maximum number of the same gauge stranded copper conductors allowed per wire funnel: AWG # #0 #8 #6 #4 # No. of Wires Application Notes. Compatibility To ensure proper operation with the I/O module, do not exceed the voltage and current ratings of the IFM. 3 5 Pinout B B B3. Wiring Refer to the Label Section on page 74. For Field-Side Wiring Diagrams, refer to Publication (Digital Programmable Controller Wiring Systems Installation Wiring Diagrams) or the Wiring System web page at chassis/49.html. Refer to the online documentation for new product information and for the most up to date set of wiring diagrams. 3. Fusing 40 fuse holders are included with the IFM. Fuses (5 x 0mm) are not included. 4. Isolation The power bus and fuse clips are isolated into 4 groups of 0 terminals (8 fuse clips). This allows each group of output devices to reference a different power source. 5. Dimensions See page 69. (odd) (even) A A A A A A B8 B9 B0 B B B3 B38 B39 B40 A3 A3 A9 A0 A9 A0 A9 A30 A39 A40

61 Digital Programmable Controller Wiring Systems 6 49-IFM40F-F4- Specifications Approvals Voltage Rating Maximum Peak Voltage ➊ Maximum Current (per Circuit) Maximum Current (per Module) Indicator Circuit Current (Nominal) UL Component Recognized (File E374 Guide NRAQ) CSA Certified (File LR34 Class 307) CE Approved 0 30V AC/DC 600V p A No. of Terminals per Device Common 0 A ma Wire Range (Rated Cross Section) ➋ # # AWG (0. 4mm ) Wire Strip Length Recommended Tightening Torque Operating Temperature Range 0.3 (8mm) lb.-in. ( Nm) 0 C to +60 C ➊ For transients >600V p, use a UL recognized suppression device rated at.5kv withstand. ➋ Maximum number of the same gauge stranded copper conductors allowed per wire funnel: AWG # #0 #8 #6 #4 # No. of Wires Application Notes. Compatibility To ensure proper operation with the I/O module, do not exceed the voltage and current ratings of the IFM. When this IFM is used with a hard contact (relay) output circuit that switches an inductive load, surge suppression must be used (i.e., a N4004 diode reverse wired across a DC load).. Wiring Refer to the Label Section on page 74. For Field-Side Wiring Diagrams, refer to Publication (Digital Programmable Controller Wiring Systems Installation Wiring Diagrams) or the Wiring System web page at chassis/49.html. Refer to the online documentation for new product information and for the most up to date set of wiring diagrams. 3 5 (odd) (even) Pinout B B B3 B8 B9 B0 B B B3 3. Fusing 40 fuse holders are included with the IFM. Fuses (5 x 0mm) are not included. 4. Isolation The power bus, fuse clips, and blown fuse indicators are isolated into 4 groups of 0 terminals (8 fuse clips and blown fuse indicators). This allows each group of output devices to reference a different power source. 5. Dimensions See page A A A9 A0 A A A9 A0 A A A9 A30 B38 B39 B40 A3 A3 A39 A40 Allen-Bradley Replacements Blown Fuse Indicator Circuit

62 6 Digital Programmable Controller Wiring Systems 49-IFM40F-F0- Specifications Approvals Voltage Rating Maximum Peak Voltage ➊ Maximum Current (per Circuit) Maximum Current (per Module) Indicator Circuit Current (Nominal) UL Component Recognized (File E374 Guide NRAQ) CSA Certified (File LR34 Class 307) CE Approved 85 3V AC 600V p A A.5mA No. of Terminals per Device Common 0 Wire Range (Rated Cross Section) ➋ # # AWG (0. 4mm ) Wire Strip Length Recommended Tightening Torque Operating Temperature Range 0.3 (8mm) lb.-in. ( Nm) 0 C to +60 C ➊ For transients >600V p, use a UL recognized suppression device rated at.5kv withstand. ➋ Maximum number of the same gauge stranded copper conductors allowed per wire funnel: AWG # #0 #8 #6 #4 # No. of Wires Application Notes. Compatibility To ensure proper operation with the I/O module, do not exceed the voltage and current ratings of the IFM. When this IFM is used with a hard contact (relay) output circuit that switches an inductive load, surge suppression must be used (i.e., a N4004 diode reverse wired across a DC load).. Wiring Refer to the Label Section on page 74. For Field-Side Wiring Diagrams, refer to Publication (Digital Programmable Controller Wiring Systems Installation Wiring Diagrams) or the Wiring System web page at chassis/49.html. Refer to the online documentation for new product information and for the most up to date set of wiring diagrams. 3 5 (odd) (even) Pinout B B B3 B8 B9 B0 B B B3 3. Fusing 40 fuse holders are included with the IFM. Fuses (5 x 0mm) are not included. 4. Isolation The power bus, fuse clips, and blown fuse indicators are isolated into 4 groups of 0 terminals (8 fuse clips and blown fuse indicators). This allows each group of output devices to reference a different power source. 5. Dimensions See page A A A9 A0 A A A9 A0 A A A9 A30 B38 B39 B40 A3 A3 A39 A40 Blown Fuse Indicator Circuit

63 Digital Programmable Controller Wiring Systems IFM40F-FS- Specifications Approvals Voltage Rating Maximum Peak Voltage ➊ Maximum Current (per Circuit) Maximum Current (per Module) Indicator Circuit Current (Nominal) UL Component Recognized (File E374 Guide NRAQ) UL Recognized per Canadian Safety Standards (cur) (File E374 Guide NRAQ) CE Approved 0 3V AC/DC 600V p A No. of Terminals per Device Common Wire Range (Rated Cross Section) ➋ # # AWG (0. 4mm ) Wire Strip Length Recommended Tightening Torque Operating Temperature Range A NA 0.3 (8mm) lb.-in. ( Nm) 0 C to +60 C ➊ For transients >600V p, use a UL recognized suppression device rated at.5kv withstand. ➋ Maximum number of the same gauge stranded copper conductors allowed per wire funnel: AWG # #0 #8 #6 #4 # No. of Wires Application Notes. Compatibility To ensure proper operation with the I/O module, do not exceed the voltage and current ratings of the IFM. 6 (even) Pinout B3. Wiring Refer to the Label Section on page 74. For Field-Side Wiring Diagrams, refer to Publication (Digital Programmable Controller Wiring Systems Installation Wiring Diagrams) or the Wiring System web page at chassis/49.html. Refer to the online documentation for new product information and for the most up to date set of wiring diagrams (odd) 35 B8 A3 A8 3. Fusing 0 fuse holders are included with the IFM. Fuses (5 x 0mm) are not included. 4. Isolation The fuse clips are isolated into 6 groups of terminals. This allows each group of output devices to reference a different power source. 5. Dimensions See page 69. Allen-Bradley Replacements

64 64 Digital Programmable Controller Wiring Systems 49-IFM40F-FS4- Specifications Approvals Voltage Rating Maximum Peak Voltage ➊ Maximum Current (per Circuit) Maximum Current (per Module) Indicator Circuit Current (Nominal) UL Component Recognized (File E374 Guide NRAQ) UL Recognized per Canadian Safety Standards (cur) (File E374 Guide NRAQ) CE Approved 0 30V AC/DC 600V p A No. of Terminals per Device Common A ma Wire Range (Rated Cross Section) ➋ # # AWG (0. 4mm ) Wire Strip Length Recommended Tightening Torque Operating Temperature Range 0.3 (8mm) lb.-in. ( Nm) 0 C to +60 C ➊ For transients >600V p, use a UL recognized suppression device rated at.5kv withstand. ➋ Maximum number of the same gauge stranded copper conductors allowed per wire funnel: AWG # #0 #8 #6 #4 # No. of Wires Application Notes. Compatibility To ensure proper operation with the I/O module, do not exceed the voltage and current ratings of the IFM. When this IFM is used with a hard contact (relay) output circuit that switches an inductive load, surge suppression must be used (i.e., a N4004 diode reverse wired across a DC load). 6 (even) 36 5 Pinout B3 B8 A3. Wiring Refer to the Label Section on page 74. For Field-Side Wiring Diagrams, refer to Publication (Digital Programmable Controller Wiring Systems Installation Wiring Diagrams) or the Wiring System web page at chassis/49.html. Refer to the online documentation for new product information and for the most up to date set of wiring diagrams. (odd) 35 A8 3. Fusing 0 fuse holders are included with the IFM. Fuses (5 x 0mm) are not included. 4. Isolation The fuse clips and blown fuse indicators are isolated into 6 groups of terminals. This allows each group of output devices to reference a different power source. Blown Fuse Indicator Circuit 5. Dimensions See page 69.

65 Digital Programmable Controller Wiring Systems IFM40F-FS0- Specifications Approvals Voltage Rating Maximum Peak Voltage ➊ Maximum Current (per Circuit) Maximum Current (per Module) Indicator Circuit Current (Nominal) UL Component Recognized (File E374 Guide NRAQ) UL Recognized per Canadian Safety Standards (cur) (File E374 Guide NRAQ) CE Approved 85 3V AC/DC 600V p A A.5mA No. of Terminals per Device Common Wire Range (Rated Cross Section) ➋ # # AWG (0. 4mm ) Wire Strip Length Recommended Tightening Torque Operating Temperature Range 0.3 (8mm) lb.-in. ( Nm) 0 C to +60 C ➊ For transients >600V p, use a UL recognized suppression device rated at.5kv withstand. ➋ Maximum number of the same gauge stranded copper conductors allowed per wire funnel: AWG # #0 #8 #6 #4 # No. of Wires Application Notes. Compatibility To ensure proper operation with the I/O module, do not exceed the voltage and current ratings of the IFM. When this IFM is used with a hard contact (relay) output circuit that switches an inductive load, surge suppression must be used (i.e., a N4004 diode reverse wired across a DC load). 6 (even) 36 5 Pinout B3 B8 A3. Wiring Refer to the Label Section on page 74. For Field-Side Wiring Diagrams, refer to Publication (Digital Programmable Controller Wiring Systems Installation Wiring Diagrams) or the Wiring System web page at chassis/49.html. Refer to the online documentation for new product information and for the most up to date set of wiring diagrams. (odd) 35 A8 3. Fusing 0 fuse holders are included with the IFM. Fuses (5 x 0mm) are not included. 4. Isolation The fuse clips and blown fuse indicators are isolated into 6 groups of terminals. This allows each group of output devices to reference a different power source. Blown Fuse Indicator Circuit 5. Dimensions See page 69. Allen-Bradley Replacements

66 66 Digital Programmable Controller Wiring Systems 49-IFM40F-FS0-4 Specifications Approvals Voltage Rating Maximum Peak Voltage ➊ Maximum Current (per Circuit) Maximum Current (per Module) Indicator Circuit Current UL Component Recognized (File E374 Guide NRAQ) UL Recognized per Canadian Safety Standards (cur) (File E374 Guide NRAQ) CE Approved 85 3V AC/DC 600V p A A.4mA No. of Terminals per Device Common Wire Range (Rated Cross Section) ➋ # # AWG (0. 4mm ) Wire Strip Length Recommended Tightening Torque Operating Temperature Range 0.3 (8mm) lb.-in. ( Nm) 0 C to +60 C ➊ For transients >600V p, use a UL recognized suppression device rated at.5kv withstand. ➋ Maximum number of the same gauge stranded copper conductors allowed per wire funnel: AWG # #0 #8 #6 #4 # No. of Wires Application Notes. Compatibility To ensure proper operation with the I/O module, do not exceed the voltage and current ratings of the IFM. When this IFM is used with a hard contact (relay) output circuit that switches an inductive load, surge suppression must be used (i.e., a N4004 diode reverse wired across a DC load) Pinout A3 B3 A B A4 B4. Wiring Refer to the Label Section on page 74. For Field-Side Wiring Diagrams, refer to Publication (Digital Programmable Controller Wiring Systems Installation Wiring Diagrams) or the Wiring System web page at chassis/49.html. Refer to the online documentation for new product information and for the most up to date set of wiring diagrams. 3. Fusing 0 fuse holders are included with the IFM. Fuses (5 x 0mm) are not included. 4. Extra Terminals Two field-side terminals are internally connected on the IFM for each channel, and are available for power source common connections A5 B5 (odd) A3 B3 A33 B33 (even) A30 B30 A3 B3 5. Isolation The fuse clips and blown fuse indicators are isolated into 6 groups of terminals. This allows each group of output devices to reference a different power source. 6. Dimensions See page 69. Blown Fuse Indicator Circuit

67 Digital Programmable Controller Wiring Systems IFM40F-FS4A-4 Specifications Approvals Voltage Rating Maximum Peak Voltage ➊ Maximum Current (per Circuit) Maximum Current (per Module) Indicator Circuit Current UL Component Recognized (File E374 Guide NRAQ) UL Recognized per Canadian Safety Standards (cur) (File E374 Guide NRAQ) CE Approved 0 30V AC/DC 600V p A A 3.mA No. of Terminals per Device Common Wire Range (Rated Cross Section) ➋ # # AWG (0. 4mm ) Wire Strip Length Recommended Tightening Torque Operating Temperature Range 0.3 (8mm) lb.-in. ( Nm) 0 C to +60 C ➊ For transients >600V p, use a UL recognized suppression device rated at.5kv withstand. ➋ Maximum number of the same gauge stranded copper conductors allowed per wire funnel: AWG # #0 #8 #6 #4 # No. of Wires Application Notes. Compatibility To ensure proper operation with the I/O module, do not exceed the voltage and current ratings of the IFM.. Wiring Refer to the Label Section on page 74. For Field-Side Wiring Diagrams, refer to Publication (Digital Programmable Controller Wiring Systems Installation Wiring Diagrams) or the Wiring System web page at chassis/49.html. Refer to the online documentation for new product information and for the most up to date set of wiring diagrams. 3. Fusing 0 fuse holders are included with the IFM. Fuses (5 x 0mm) are not included. 4. Extra Terminals Two field-side terminals are internally connected on the IFM for each channel, and are available for power source common connections. 5. Isolation The fuse clips and blown fuse indicators are isolated into 6 groups of terminals. This allows each group of output devices to reference a different power source Pinout A B A4 B4 (even) A30 B30 A3 B3 A3 B3 A5 B5 (odd) A3 B3 A33 B33 6. Dimensions See page 69. Blown Fuse Indicator Circuit Allen-Bradley Replacements

68 68 Digital Programmable Controller Wiring Systems 49-IFM40F-FS0A-4 Specifications Approvals Voltage Rating Maximum Peak Voltage ➊ Maximum Current (per Circuit) Maximum Current (per Module) Indicator Circuit Current UL Component Recognized (File E374 Guide NRAQ) UL Recognized per Canadian Safety Standards (cur) (File E374 Guide NRAQ) CE Approved 85 3V AC/DC 600V p A A.4mA No. of Terminals per Device Common Wire Range (Rated Cross Section) ➋ # # AWG (0. 4mm ) Wire Strip Length Recommended Tightening Torque Operating Temperature Range 0.3 (8mm) lb.-in. ( Nm) 0 C to +60 C ➊ For transients >600V p, use a UL recognized suppression device rated at.5kv withstand. ➋ Maximum number of the same gauge stranded copper conductors allowed per wire funnel: AWG # #0 #8 #6 #4 # No. of Wires Application Notes. Compatibility To ensure proper operation with the I/O module, do not exceed the voltage and current ratings of the IFM.. Wiring Refer to the Label Section on page 74. For Field-Side Wiring Diagrams, refer to Publication (Digital Programmable Controller Wiring Systems Installation Wiring Diagrams) or the Wiring System web page at chassis/49.html. Refer to the online documentation for new product information and for the most up to date set of wiring diagrams. 3. Fusing 0 fuse holders are included with the IFM. Fuses (5 x 0mm) are not included. 4. Extra Terminals Two field-side terminals are internally connected on the IFM for each channel, and are available for power source common connections. 5. Isolation The fuse clips and blown fuse indicators are isolated into 6 groups of terminals. This allows each group of output devices to reference a different power source Pinout A B A4 B4 (even) A30 B30 A3 B3 A3 B3 A5 B5 (odd) A3 B3 A33 B33 6. Dimensions See page 69. Blown Fuse Indicator Circuit

69 Digital Programmable Controller Wiring Systems 69 Dimensions 49-IFM0F 49-IFM0D4 49-IFM0D0.67 in (4.5 mm).78 in (70.5 mm) 4.33 in (0 mm) 3.7 in (83 mm) 49-IFM0FN 49-IFM0D4N 49-IFM0D0N.9 in (55.5 mm).67 in (4.5 mm).78 in (70.5 mm).36 in (60 mm) 3.7 in (83 mm) 49-IFM0F- 49-IFM0D4-49-IFM0D4A- 49-IFM0D0-49-IFM0D0A-.9 in (55.5 mm).67 in (4.5 mm).78 in (70.5 mm) 4.33 in (0 mm) 3.7 in (83 mm) 49-IFM0F-3 49-IFM0D in (69.5 mm).9 in (55.5 mm).67 in (4.5 mm).78 in (70.5 mm) 4.33 in (0 mm) 3.7 in (83 mm) Allen-Bradley Replacements

70 70 Digital Programmable Controller Wiring Systems Dimensions, (Continued) 49-IFM0DS IFM0DS in (70.5 mm).9 in (55.5 mm).67 in (4.5 mm) 4.33 in (0 mm) 3.7 in (83 mm) 49-IFM0F-F- 49-IFM0F-F4-49-IFM0F-F0-.9 in (55.5 mm).67 in (4.5 mm).78 in (70.5 mm) 4.33 in (0 mm) 3.7 in (83 mm) 49-IFM0F-F4A-.9 in (55.5 mm).67 in (4.5 mm).78 in (70.5 mm) 4.33 in (0 mm) 3.7 in (83 mm) 49-IFM0F-FS- 49-IFM0F-FS4-49-IFM0F-FS0-.9 in (55.5 mm).67 in (4.5 mm).78 in (70.5 mm).36 in (60 mm) 3.7 in (83 mm) 49-IFM40F 49-IFM40D4.9 in (55.5 mm).67 in (4.5 mm).78 in (70.5 mm) 4.33 in (0 mm) 3.7 in (83 mm)

71 Digital Programmable Controller Wiring Systems 7 Dimensions, (Continued) 49-IFM40F- 49-IFM40D4-49-IFM40D4A- 49-IFM40D0-49-IFM40D0A- 8.7 in (0 mm).9 in (55.5 mm).67 in (4.5 mm).78 in (70.5 mm) 3.7 in (83 mm) 49-IFM40F-3 49-IFM40D in (0 mm).74 in (69.5 mm).9 in (55.5 mm).67 in (4.5 mm).78 in (70.5 mm) 3.7 in (83 mm) Allen-Bradley Replacements

72 7 Digital Programmable Controller Wiring Systems Dimensions, (Continued) 49-IFM40DS IFM40DS in (70 mm).78 in (70.5 mm).9 in (55.5 mm).67 in (4.5 mm) 3.7 in (83 mm) 49-IFM40DS4A-4 49-IFM40DS0A in (70 mm).78 in (70.5 mm).9 in (55.5 mm).67 in (4.5 mm) 3.7 in (83 mm)

73 Digital Programmable Controller Wiring Systems 73 Dimensions, (Continued) 49-IFM40F-F4-49-IFM40F-F0-8.7 in (0 mm).9 in (55.5 mm).67 in (4.5 mm).78 in (70.5 mm) 3.7 in (83 mm) 49-IFM40F-FS IFM40F-FS0A in (80 mm).78 in (70.5 mm).9 in (55.5 mm).67 in (4.5 mm) 3.7 in (83 mm) 49-IFM40F-FS- 49-IFM40F-FS4-49-IFM40F-FS0-.9 in (55.5 mm).67 in (4.5 mm).78 in (70.5 mm) 4.7 in 3.7 in (0 mm) (83 mm) Allen-Bradley Replacements

74 74 Digital Programmable Controller Wiring Systems Adhesive Label Cards All Bulletin 49 IFMs come with an adhesive label card. The label card provides the field-side connection descriptions for the programmable controller I/O module. The label strips basically copy the wiring descriptions from the I/O module in the chassis down to the IFM terminals on the DIN rail. The label cards list all of the compatible I/O modules and their respective wiring descriptions. Depending on the I/O module that is used, the label strip(s) are simply peeled from the label card and applied to the field-side terminals on the IFM. Refer to the respective I/O Module Product Data for actual wiring connections and recommendations. See Reference Publications on Page 00. Labels are provided in the octal and decimal numbering systems for 746 I/O modules. Labels for 77 I/O modules are supplied in the octal numbering system, like the I/O modules themselves. IFMs with LEDs or fuse clips come with the LEDs or fuse clips/blown fuse indicators numbered in decimal. LED and fuse labels are also provided in octal for use with 77 I/O modules. The LED or fuse conversion label(s) would be placed directly on the circuit board of the IFM. For extra terminal modules, pre-printed labels are provided to identify the power bus(ses) or commoned terminals (middle and/or lower rows of terminals) on the IFM. For each I/O module, corresponding labels with L, L, COM, or +V are provided. The labels indicate isolated power busses or grouped commons with a different letter or number. For example, L-A, L-B, L-C or CM, CM, CM3, etc. In addition, if generic numbering of the field-side terminals is desired, Numeric labels are provided. Examples: -0, -40, and evens and odds. For write-on identification, the label cards contain blank label strips (for field-side terminals) and rectangular boxes (for the large group marking area on each IFM). The different labels are shown actual size on Pages 75 through 93. This information is helpful for determining field-side wiring layouts prior to installation. An example of how the labels are applied:

75 Digital Programmable Controller Wiring Systems 75 Part of Adhesive Label Card for Catalog Numbers 49-IFM0F, -IFM0D4, and -IFM0D0 Allen-Bradley Replacements

76 76 Digital Programmable Controller Wiring Systems Part of Adhesive Label Card for Catalog Numbers 49-IFM0F, -IFM0D4, and -IFM0D0

77 Digital Programmable Controller Wiring Systems 77 Adhesive Label Card for Catalog Numbers 49-IFM0FN, -IFM0D4N, and -IFM0D0N Allen-Bradley Replacements

78 78 Digital Programmable Controller Wiring Systems Part of Adhesive Label Card for Catalog Numbers 49-IFM0F-, -IFM0D4-, -IFM0D0-, -IFM0F-F-, -IFM0F-F4-, and -IFM0F-F0-

79 Digital Programmable Controller Wiring Systems 79 Part of Adhesive Label Card for Catalog Numbers 49-IFM0F-, -IFM0D4-, -IFM0D0-, -IFM0F-F-, -IFM0F-F4-, and -IFM0F-F0- Allen-Bradley Replacements

80 80 Digital Programmable Controller Wiring Systems Adhesive Label Card for Catalog Numbers 49-IFM0F-3 (Series B)

81 Digital Programmable Controller Wiring Systems 8 Adhesive Label Card for Catalog Numbers 49-IFM0D4A-, and -IFM0D0A- Allen-Bradley Replacements

82 8 Digital Programmable Controller Wiring Systems Part of Adhesive Label Card for Catalog Numbers 49-IFM0D4-3, -IFM40F-3, and -IFM40D4-3

83 Digital Programmable Controller Wiring Systems 83 Part of Adhesive Label Card for Catalog Numbers 49-IFM0D4-3, -IFM40F-3 and 49-IFM40D4-3 Allen-Bradley Replacements

84 84 Digital Programmable Controller Wiring Systems Adhesive Label Card for Catalog Numbers 49-IFM0DS4-4, and -IFM0DS0-4

85 Digital Programmable Controller Wiring Systems 85 Adhesive Label Card for Catalog Numbers 49-IFM0F-F4A-, and -IFM0F-F0A- Allen-Bradley Replacements

86 86 Digital Programmable Controller Wiring Systems Adhesive Label Card for Catalog Numbers 49-IFM0F-FS-, -IFM0F-FS4-, and -IFM0F-FS0-

87 Digital Programmable Controller Wiring Systems 87 Part of Adhesive Label Card for Catalog Numbers 49-IFM40F and -IFM40D4 Allen-Bradley Replacements

88 88 Digital Programmable Controller Wiring Systems Part of Adhesive Label Card for Catalog Numbers 49-IFM40F and -IFM40D4

89 Digital Programmable Controller Wiring Systems 89 Part of Adhesive Label Card for Catalog Numbers 49-IFM40F-, -IFM40D4-, -IFM40D4A-, -IFM40D0-, -IFM40D0A-, -IFM40F-F-, -IFM40F-F4-, and -IFM40F-F0- Allen-Bradley Replacements

90 90 Digital Programmable Controller Wiring Systems Part of Adhesive Label Card for Catalog Numbers 49-IFM40F-, -IFM40D4-, -IFM40D4A-, -IFM40D0-, -IFM40D0A-, -IFM40F-F-, -IFM40F-F4-, and -IFM40F-F0-

91 Digital Programmable Controller Wiring Systems 9 Adhesive Label Card for Catalog Numbers 49-IFM40DS4-4, -IFMDS4A-4, -IFM40DS0-4, and -IFM40DS0A-4 Allen-Bradley Replacements

92 9 Digital Programmable Controller Wiring Systems Adhesive Label Card for Catalog Numbers 49-IFM40F-FS-, -IFM40F-FS4-, and -IFM40F-FS0-

93 Digital Programmable Controller Wiring Systems 93 Adhesive Label Card for Catalog Numbers 49-IFM40F-FS0-4, -IFM40F-FS4A-4 and -IFM40F-FS0A-4 Allen-Bradley Replacements