PK1. Alarms & Remote Start. Automotive Data Solutions Inc.

Transcription

1 Alarms & Remote Start Automotive Data Solutions Inc. INSTALL GUIDE ADS-AL(TB)-PK PK Available for : ADS-AL CA Rev. Date: November 03, 0 Doc. No.: ##7068## 0094 The brand names and logos found in this guide are property of their respective owners. Automotive Data Solutions Inc. 0 NOTICE: The manufacturer will accept no responsibility for any electrical damage resulting from improper installation of this product, be that either damage to the vehicle itself or to the installed device. This device must be installed by a certified technician. This guide has been written for properly trained technicians; a certain level of skill & knowledge is therefore assumed. Please!review the Installation Guide carefully before beginning any work.

2 Page of 5 ADS-AL(TB)-PK Doc. No.: ##7068## 0094 install type SeLeCtiOn MaKe ModeL year InsTaLL Type CHeVroLeT Venture 99 oldsmobile pontiac Silhouette 99 Grand Prix Transport 99 Automotive Data Solutions Inc. 0

3 Page 3 of 5 ADS-AL(TB)-PK Doc. No.: ##7068## 0094 type - wiring DIAGRAM REMOTE STARTER GRAY ORANGE PURPLE BLACK BLUE PINK PK3 V (+) GROUND (-) GROUND WHEN RUNNING (-) OUTPUT DATA MODE LEGEND NOT REQUIRED IN DATA MODE (-WAY) NOT REQUIRED IN DATA MODE (-WAY) USE DATA MODE OR HARDWIRE MODE DATA MODE GWR (-) INPUT - BLUE/WHITE (NC) WHITE GROUND - BLACK V (+) - RED (NC) GREEN/BLACK (NC) BLUE/BLACK (NC) RED/WHITE (NC) BROWN (NC) PURPLE/YELLOW (NC) PURPLE/BLACK (NC) WHITE (NC) BLACK/WHITE (NC) GREEN (NC) PURPLE/WHITE WHITE/BLACK (NC) WHITE/RED (NC) WHITE (NC) YELLOW/BLACK (NC) YELLOW/RED (NC) YELLOW (NC) BROWN/RED (NC) BROWN/YELLOW (NC) ORANGE/BLACK - DATA OUTPUT ORANGE/WHITE (NC) ORANGE (NC) PINK/BLACK - IGNITION OUTPUT IMMOBILIZER SIDE PINK - IGNITION INPUT ECM SIDE BLUE/RED (NC) BLUE/YELLOW (NC) GREEN/RED (NC) GREEN/YELLOW (NC) GRAY/RED (NC) GRAY/YELLOW (NC) Automotive Data Solutions Inc. 0

4 Page 4 of 5 ADS-AL(TB)-PK Doc. No.: ##7068## 0094 installation MODe SeLeCtiOn Press and release programming button to select installation mode. LED flashes (X) once = DATA MODE LED flashes (X) twice = STANDARD HARDWIRE MODE! Press and hold programming button until LED turns solid GREEN to register selection. After registration, follow Factory Reset Procedure to change installation mode and restart this procedure. MODULe PrOgrAMMing PrOCeDUre Insert key into ignition. 3 Wait, LED will turn solid GREEN for seconds. ON Turn key to ON position. 4 5 OFF Turn key to OFF position. Module Programming Procedure completed. Automotive Data Solutions Inc. 0

5 Page 5 of 5 ADS-AL(TB)-PK Doc. No.: ##7068## 0094 identify VeHiCLe year Locate the Vehicle Identification Number (VIN) and identify the 0th character. 4 3 A 5 Y N 5 T A L 8 D 5 R 0 X Match the VIN s 0th character to its corresponding year. L > 990 s > 995 y > > 005 a > 00 M > 99 T > 996 > 00 6 > 006 B > 0 n > 99 V > 997 > 00 7 > 007 C > 0 p > 993 W > > > 008 d > 03 r > 994 X > > > 009 e > 04 Led status Flashing RED diagnostics during programming during remote start WITH IGnITIon off Missing/wrong information from firmware or vehicle Incorrectly programmed Solid RED Waiting for more vehicle information Incorrectly programmed Flashing GREEN Additional steps required to complete programming MODULe DiAgnOStiCS Correctly programmed and operational Incorrectly programmed or connected Not programmed waiting for more vehicle information False ground when running status from remote starter Solid GREEN then OFF Correctly programmed Reset in progress Reset in progress OFF No activity or already programmed Invalid ground when running status from remote starter At rest and ready for a remote start sequence FACtOry reset PrOCeDUre DISCONNECT all connectors from module EXCEPT the black 4-PIN standard or optional data DISCONNECT black 4-PIN standard or optional data 5 6 LED will turn solid red for seconds. RESET COMPLETED. RECONNECT all connectors. 3 4 PRESS AND HOLD programming button while connecting either 4-PIN standard or optional data When LED flashes red, RELEASE programming button. 7! Repeat programming procedure. Failure to follow procedure may result with a DTC or a CHECK ENGINE error message. Automotive Data Solutions Inc. 0