P4P800-E Deluxe. Motherboard

Transcription

1 P4P800-E Deluxe Motherboard

2 Checklist Copyright 2004 ASUSTeK COMPUTER INC. All Rights Reserved. ii

3 iii Features

4 Safeguards iv

5 v

6 vi

7 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with manufacturer s instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus set out in the Radio Interference Regulations of the Canadian Department of Communications. This class B digital apparatus complies with Canadian ICES-003. vii

8 viii

9 ix

10 x

11

12

13

14

15 1-1

16 1-2

17 1-3

18 1-4

19 1-5

20 1-6

21

22

23 SB_PWR P4P800-E P4P800-E Onboard LED ON Standby Power OFF Powered Off 2-1

24 2-2

25 24.5cm (9.6in) PS/2KBMS T: Mouse B: Keyboard SPDIF_O KBPWR Socket 478 CPU_FAN Super I/O SPDIF_O2 COM1 PARALLEL PORT Bottom: Top: USB1 USB USB2.0 Top: T: USB3 RJ-45 B: USB4 Top:Bass Center: Back surround L/R Below: Side surround L/R Top:Line In Center:Line Out Below:Mic In ATX12V1 USBPW12 USBPW34 Intel 82865PE Memory Controller Hub Accelerated Graphics Port (AGP) DDR DIMM_A1 (64 bit,184-pin module) DDR DIMM_A2 (64 bit,184-pin module) DDR DIMM_B1 (64 bit,184-pin module) DDR DIMM_B2 (64 bit,184-pin module) ATX Power Connector PRI_IDE1 SEC_IDE1 FLOPPY1 30.5cm (12.0in) Marvell 88E8001 Gbit MODEM CD Audio Codec FP_AUDIO VIA VT6307 Chipset AUX PCI1 PCI2 PCI3 P4P800-E PCI4 PCI5 WIFI IE1394_2 USBPW56 USBPW78 USB_56 PROMISE PDC20378 GAME Intel ICH5R USB_78 SATA_RAID2 SATA_RAID1 SMB20 CHASSIS SATA2 SATA1 4Mbit Firmware Hub PRI_RAID COM2 CHA_FAN PWR_FAN CLRTC CR2032 3V Lithium Cell CMOS Power Speech Controller PANEL SB_PWR 2-3

26 2-4

27 2-5

28 2-6

29 90º~100º 2-7

30 2-8

31 2-9

32 2-10

33 2-11

34 80 Pins P4P800-E 104 Pins DIMM_A1 DIMM_A2 DIMM_B1 DIMM_B2 P4P800-E 184-Pin DDR DIMM Sockets 2-12

35 DIMM_A1 DIMM_A2 DIMM_B1 DIMM_B2 ( ) ( ) ( ) ( ) (1) (2) (3) (4) (1) - - (2) - - (3)* CPU FSB DDR DIMM 800 MHz PC3200/PC2700*/PC /333*/266 MHz 533 MHz PC2700/PC /266 MHz 400 MHz PC MHz 2-13

36 SS/DS A* B* C* 256MB Apacer SAMSUNG SS K4H560838D-TCC4 256MB Apacer SAMSUNG SS K4H560838D-TCC4 256MB Transcend TS32MLD64V4F3 MOSEL SS V58C SAT5B 512MB Transcend TS64MLD64V4F3 Mosel DS V58C SAT5B 256MB A DATA MDGAD5F3G315B1EC2 ADATA SS ADD8608A8A-5B 256MB A DATA MDOWB5F3G316B1EAE Winbond SS W942508BH-5 512MB MICRON MT16VDDT6464AG-40BCB MICRON DS MT46V32M8TG-5BC 128MB Infineon HYS64D16301GU-5-B Infineon SS HYB25D256160BT-5B 256MB Infineon HYS64D32300GU-5-B Infineon SS HYB25D256800BT-5B 512MB Infineon HYS64D32300HU-5-B Infineon DS HYB25D256800CE-5B 256MB Infineon HYS64D32300HU-5-C Infineon DS HYB25D256800CE-5C 512MB Winbond W9451GCDB-5 Winbond DS W942508CH-5 256MB SAMSUNG M368L3223ETM-CCC SAMSUNG SS K4H560838E-TCCC 512MB SAMSUNG M368L6423FTM-CCC SAMSUNG DS K4H560838F-TCCC 256MB TwinMOS M2G9I08AFATT9F081AA4T TwinMOS SS TMD7608F8E50D 256MB TwinMOS M2S9I08AFAPS9F0811A-T PSC SS A2S56D30ATP 256MB Hynix HYMD232646B8J-D43 AA Hynix SS HY5DU56822BT-D43 512MB Corsair CMX C2 XMS3202v1.2 N/A DS N/A 256MB ATP AG32L64T8SQC4S SAMSUNG SS K4H560838D-TCC4 256MB CENTURY DXV6S8SSCCD3K27C SAMSUNG SS K4H560838D-TCCC 512MB CENTURY DXV2S8SSCCD3K27C SAMSUNG DS K4H560838D-TCCC 256MB Kingston KVR400X64C3A/256 hynix SS HY5DU56822BT-D43 256MB KINGMAX MPXB62D-38KT3R KINGMAX SS KDL388P4EA MB KINGMAX MPXC22D-38KT3R KINGMAX DS KDL388P4EA-50(A) 512MB KINGMAX MPXC22D-38KT3R KINGMAX DS V58C SAT5B 128MB NANYA NT128D64SH4B1G-5T NANYA SS NT5DS16M16BT-5T 256MB Elixir M2U25664DS88B3G-5T Elixir SS N2DS25680BT-5T 512MB Elixir M2U51264DS8HB3G-5T Elixir DS N2DS25680BT-5T 256MB Kreton N/A Kreton SS VT T-5 512MB Kreton N/A Kreton DS VT T-5 256MB Veritech VT400FMV/ Veritech SS VT56DD32M8PC

37 2-15

38 2-16

39 IRQ N/A 3* 11 (COM2) 4* 12 (COM1) 5* 13 (LPT2 ) * 15 (LPT1) 8 3 CMOS/ 9* 4 ACPI 10* 5 PCI IRQ 11* 6 PCI IRQ 12* 7 PS/ * 9 1 IDE 15* 10 2 IDE A B C D E F G H PCI 1 PCI 2 PCI 3 PCI 4 PCI 5 AGP LAN 2-17

40 P4P800-E Keyed for 1.5v P4P800-E Accelerated Graphics Port (AGP) 2-18

41 P4P800-E WIFI P4P800-E WIRELESS Connectors 2-19

42 CLRTC P4P800-E Normal (Default) Clear CMOS P4P800-E Clear RTC RAM 2-20

43 P4P800-E V (Default) 1 2 USBPW12 USBPW VSB USBPW56 USBPW P4P800-E USB Device Wake Up +5V (Default) +5VSB 2-21

44 1 2 KBPWR V +5VSB (Default) P4P800-E P4P800-E Keyboard Power Setting SMB P4P800-E P4P800-E SMB2.0 Support Enable Disable (Default) 2-22

45

46 2-24

47 NOTE: FLOPPY Orient the red markings on the floppy ribbon cable to PIN 1. P4P800-E PIN 1 P4P800-E Floppy Disk Drive Connector P4P800-E PRI_IDE1 SEC_IDE1 NOTE: Orient the red markings (usually zigzag) on the IDE ribbon cable to PIN 1. P4P800-E IDE Connectors PIN

48 SATA2 GND RSATA_TXP2 RSATA_TXN2 GND RSATA_RXP2 RSATA_RXN2 GND SATA1 P4P800-E P4P800-E SATA Connectors GND RSATA_TXP1 RSATA_TXN1 GND RSATA_RXP1 RSATA_RXN1 GND 2-26

49 1. Windows 2000/XP 2. Windows 98SE/ME P-ATA S-ATA (2 ) (2 ) (1 ) (1 ) Configuration A Configuration B Configuration C : Windows Windows 98SE/ME BIOS 2000/XP A B C IDE S-ATA IDE - Primary P-ATA+S-ATA Sec. P-ATA+S-ATA P-ATA 2-27

50 PRI_RAID P4P800-E P4P800-E RAID Connectors PIN 1 NOTE: Orient the red markings (usually zigzag) on the IDE ribbon cable to PIN

51 SATA_RAID2 GND RSATA_TXP2 RSATA_TXN2 GND RSATA_RXP2 RSATA_RXN2 GND SATA_RAID1 P4P800-E P4P800-E SATA RAID Connectors GND RSATA_TXP1 RSATA_TXN1 GND RSATA_RXP1 RSATA_RXN1 GND 2-29

52 CPU_FAN CHA_FAN GND +12V Rotation GND +12V Rotation P4P800-E P4P800-E 12-Volt Fan Connectors PWR_FAN GND +12V Rotation COM2 PIN 1 P4P800-E P4P800-E Serial COM2 Bracket 2-30

53 ATXPWR ATX12V P4P800-E +3.3VDC -12.0VDC COM PS_ON# COM COM COM -5.0VDC +5.0VDC +5.0VDC +3.3VDC +3.3VDC COM +5.0VDC COM +5.0VDC COM PWR_OK +5VSB +12.0VDC +12V DC GND +12V DC GND P4P800-E ATX Power Connectors 2-31

54 USB+5V USB_P6- USB_P6+ GND NC USB+5V USB_P8- USB_P8+ GND NC P4P800-E P4P800-E USB 2.0 Header USB_56 1 USB+5V USB_P5- USB_P5+ GND USB_78 1 USB+5V USB_P7- USB_P7+ GND 2-32

55 P4P800-E MODEM Modem-Out Ground Ground Modem-In CD(Black) AUX(White) Right Audio Channel Ground Ground Left Audio Channel P4P800-E Internal Audio Connectors P4P800-E IE1394_2 TPA0- GND TPB0- +12V GND P4P800-E IEEE-1394 Connector 1 TPA0+ GND TPB0+ +12V 2-33

56 P4P800-E FP_AUDIO MIC2 AGND MICPWR +5VA Line out_r BLINE_OUT_R NC Line out_l BLINE_OUT_L P4P800-E Front Panel Audio Connector +5V J1B2 J1CY GND GND J1CX J1B1 +5V P4P800-E GAME P4P800-E Game Connector MIDI_IN J2B2 J2CY MIDI_OUT J2CX J2B1 +5V 2-34

57 CHASSIS +5VSB_MB Chassis Signal GND P4P800-E P4P800-E Chassis Alarm Lead (Default) Power LED PLED+ Speaker Connector +5V Ground Ground Speaker Ground PWR IDE_LED P4P800-E ATX Power SMI Lead Switch* * Requires an ATX power supply. P4P800-E System Panel Connectors PLED- IDE_LED+ IDE_LED- ExtSMI# Ground Reset Ground Reset SW 2-35

58 2-36

59

60

61 3-1

62 3-2

63 3-3

64 POST PS/ IDE IDE CPU CPU CPU 3-4

65 3-5

66 3-6

67 3-7

68 3-8

69

70

71 format A:/S 4-1

72 A:\>afudos /ip4p800e.rom AMI Firmware Update Utility - Version 1.10 Copyright (C) 2002 American Megatrends, Inc. All rights reserved. Reading file... done Erasing flash... done Writing flash... 0x0008CC00 (9%) 4-2

73 A:\>afudos /ip4p800e.rom AMI Firmware Update Utility - Version 1.10 Copyright (C) 2002 American Megatrends, Inc. All rights reserved. Reading file... done Erasing flash... done Writing flash... 0x0008CC00 (9%) Verifying flash.. done A:\> A:\>afudos /omybios03.rom AMI Firmware Update Utility - Version 1.10 Copyright (C) 2002 American Megatrends, Inc. All rights reserved. Reading flash... 0x0008CC00 (9%) 4-3

74 3. BIOS 600 KB A:\>afudos /omybios03.rom AMI Firmware Update Utility - Version 1.10 Copyright (C) 2002 American Megatrends, Inc. All rights reserved. Reading flash... done A:\> User recovery requested. Starting BIOS recovery... Checking for floppy

75 User recovery requested. Starting BIOS recovery... Checking for floppy... Floppy found! Reading file P4P800-E.rom. Completed. Start flashing... Flashed successfully. Rebooting. Bad BIOS checksum. Starting BIOS recovery... Checking for floppy

76 Bad BIOS checksum. Starting BIOS recovery... Checking for floppy... Floppy found! Reading file P4P800-E.ROM. Completed. Start flashing... Bad BIOS checksum. Starting BIOS recovery... Checking for floppy... Bad BIOS checksum. Starting BIOS recovery... Checking for floppy... Floppy not found! Checking for CD-ROM... CD-ROM found. Reading file P4P800-E.ROM. Completed. Start flashing

77 4-7

78 4-8

79 4-9

80 System Time [11:10:19] System Date [Thu 03/27/2003] Legacy Diskette A [1.44M, 3.5 in] Language [English] Primary IDE Master :[ST320413A] Primary IDE Slave :[ASUS CD-S340] Secondary IDE Master :[Not Detected] Secondary IDE Slave :[Not Detected] Third IDE Master :[Not Detected] Fourth IDE Master :[Not Detected] IDE Configuration System Information Use [ENTER], [TAB] or [SHIFT-TAB] to select a field. Use [+] or [-] to configure system time. Select Screen Select Item +- Change Field Tab Select Field F1 General Help F10 Save and Exit ESC Exit 4-10

81 System Time [11:10:19] System Date [Thu 03/27/2003] Legacy Diskette A [1.44M, 3.5 in] Language [English] Primary IDE Master :[ST320413A] Primary IDE Slave :[ASUS CD-S340] Secondary IDE Master :[Not Detected] Secondary IDE Slave :[Not Detected] Third IDE Master :[Not Detected] Fourth IDE Master :[Not Detected] IDE Configuration System Information Use [ENTER], [TAB] or [SHIFT-TAB] to select a field. Use [+] or [-] to configure system time. Select Screen Select Item +- Change Field Tab Select Field F1 General Help F10 Save and Exit ESC Exit Advanced Chipset settings WARNING: Setting wrong values in the sections below may cause system to malfunction. Configure DRAM Timing by SPD Memory Acceleration Mode DRAM Idle Timer DRAm Refresh Rate [Enabled] [Auto] [Auto] [Auto] Graphic Adapter Priority [AGP/PCI] Graphics Aperture Size [ 64 MB] Spread Spectrum [Enabled] ICH Delayed Transaction [Enabled] MPS Revision [1.4] Select Screen Select Item +- Change Option F1 General Help F10 Save and Exit ESC Exit 4-11

82 System Time [11:51:19] System Date [Thu 08/05/2003] Legacy Diskette A [1.44M, 3.5 in] Language [English] Primary IDE Master : [ST320413A] Primary IDE Slave : [ASUS CD-S340] Secondary IDE Master : [Not Detected] Secondary IDE Slave : [Not Detected] Third IDE Master : [Not Detected] Fourth IDE Master : [Not Detected] IDE Configuration System Information Use [ENTER], [TAB] or [SHIFT-TAB] to select a field. Use [+] or [-] to configure system time. Select Screen Select Item +- Change Field Tab Select Field F1 General Help F10 Save and Exit ESC Exit 4-12

83 Primary IDE Master Device : Hard Disk Vendor : ST320413A Size : 20.0GB LBA Mode : Supported Block Mode : 16 Sectors PIO Mode : Supported Async DMA : MultiWord DMA-2 Ultra DMA : Ultra DMA-5 SMART Monitoring: Supported Type LBA/Large Mode Block(Multi-sector Transfer) PIO Mode DMA Mode Smart Monitoring 32Bit Data Transfer [Auto] [Auto] [Auto] [Auto] [Auto] [Auto] [Disabled] Select the type of device connected to the system. Select Screen Select Item +- Change Option F1 General Help F10 Save and Exit ESC Exit 4-13

84 IDE Configuration Onboard IDE Operate Mode [Enhanced Mode] Enhanced Mode Support On [S-ATA] Configure S-ATA as RAID [No] IDE Detect Time Out (Sec) [35] 4-14

85 4-15

86 AMI BIOS Version : Build Data : 08/04/03 Processor Type : Intel(R) Pentium(R) 4 CPU 1500MHz Speed : 1500MHz Count : 1 System Memory Size : 256MB JumperFree Configuration CPU Configuration Chipset Onboard Devices Configuration PCIPnP USB Configuration Speech Configuration Instant Music Configuration Configure CPU. Select Screen Select Item Enter Go to Sub-screen F1 General Help F10 Save and Exit ESC Exit 4-16

87 Configure System Frequency/Voltage AI Overclock Tuner [Standard] Performance Mode [Auto] 4-17

88 Configure System Frequency/Voltage AI Overclock Tuner [Manual] CPU External Frequency (MHz) [100] DRAM Frequency [Auto] AGP/PCI Frequency (MHz) [Auto] CPU VCore Voltage DDR Reference Voltage AGP VDDQ Voltage Performance Mode [Auto] [Auto] [1.50V] [Auto] (value is auto-detected) 4-18

89 Configure Advanced CPU settings Manufacturer: Intel(R) Brand String: Intel(R) Pentium(R) 4 CPU 1500MHz Frequency : 1500Mhz FSB Speed : 400Mhz Cache L1 Cache L2 Cache L3 : 8 KB : 25 KB : 0 KB Rario Status: Locked Ratio Actual Value: 15 VID CMOS Setting: [ 62] Max CPUID Value Limit: [Disabled] CPU Internal Thermal Control [Auto] Hyper Threading Function [Enabled] Select Screen Select Item +- Change Option F1 General Help F10 Save and Exit ESC Exit 4-19

90 Advanced Chipset Settings WARNING: Setting wrong values in the sections below may cause system to malfunction. Configure DRAM Timing by SPD Memory Acceleration Mode DRAM Idle Timer DRAM Refresh Rate [Enabled] [Auto] [Auto] [Auto] Graphic Adapter Priority [AGP/PCI] Graphics Aperture Size [ 64MB] Spread Spectrum [enabled] ICH Delayed Transaction [Enabled] MPS Revision [1.4] Select Screen Select Item +- Change Option F1 General Help F10 Save and Exit ESC Exit 4-20

91 4-21

92 OnBoard AC 97 Audio OnBoard Promise Controller OnBoard IEEE 1394 Controller Onboard LAN OnBoard LAN Boot ROM [Auto] [Enabled] [Enabled] [Enabled] [Disabled] Serial Port1 Address [3F8/IRQ4] Serial Port2 Address [2F8/IRQ3] Parallel Port Address [378] Parallel Port Mode [ECP] ECP Mode DMA Channel [DMA3] Parallel Port IRQ [IRQ7] OnBoard Game/MIDI Port [Disabled] 4-22

93 4-23

94 Advanced PCI/PnP Settings WARNING: Setting wrong values in below sections may cause the system to malfunction. Plug And Play O/S [No] PCI Latency Timer [64] Allocate IRQ to PCI VGA [Yes] Palette Snooping [Disabled] PCI IDE BusMaster [Enabled] IRQ3 IRQ4 IRQ5 IRQ7 IRQ9 IRQ10 IRQ11 IRQ14 IRQ15 [Available] [Available] [Available] [Available] [Available] [Available] [Available] [Available] [Available] Select Screen Select Item +- Change Option F1 General Help F10 Save and Exit ESC Exit PCI Slot-1/5 IRQ Preference PCI Slot-2 IRQ Preference PCI Slot-3 IRQ Preference PCI Slot-4 IRQ Preference [Auto] [Auto] [Auto] [Auto] Select Item +- Change Option F1 General Help F10 Save and Exit ESC Exit 4-24

95 USB Configuration Module Version : USB Devices Enabled: None USB Function Legacy USB Support USB 2.0 Controller USB 2.0 Controller Mode [Enabled] [Auto] [Enabled] [HiSpeed] USB Mass Storage Device Configuration 4-25

96 USB Mass Storage Device Configuration USB Mass Storage Reset Delay [20 Sec] No USB Mass Storage device detected 4-26

97 Speech Option Speech Post Reporter Report IDE Error Report System Booting [Enabled] [Disabled] [Disabled] Instant Music Option Instant Music [Disabled] 4-27

98 Suspend Mode Repost Video on S3 Resume ACPI 2.0 Support ACPI APIC Support BIOS -> AML ACPI Table APM Configuration Hardware Monitor [Auto] [No] [No] [Enabled] [Enabled] Configure CPU. Select Screen Select Item Enter Go to Sub-screen F1 General Help F10 Save and Exit ESC Exit 4-28

99 APM Configuration Power Management/APM [Enabled] Video Power Down Mode [Suspend] Hard Disk Power Down Mode [Suspend] Suspend Time Out [Disabled] Throttle Slow Clock Ratio [50%] Enabled or disable APM. Power Button Mode Restore On AC Power Loss Power On By RTC Alarm Power On By External Modem Power On By PCI Devices Power On By PS/2 Keyboard Power On By PS/2 Mouse [On/Off] [Power Off] [Disabled] [Disabled] [Disabled] [Disabled] [Disabled] Select Screen Select Item +- Change Option F1 General Help F10 Save and Exit ESC Exit 4-29

100 4-30

101 Hardware Monitor CPU Temperature MB Temperature Power Temperature CPU Fan Control [44ºC/111ºF] [36ºC/96.5ºF] [N/A] [Disabled] CPU Fan Speed [2393RPM] Chassis Fan Speed [N/A] Power Fan Speed [N/A] VCORE Voltage [ 1.465V] 3.3V Voltage [ 3.328V] 5V Voltage [ 5.026V] 12V Voltage [11.795V] Select Screen Select Item +- Change Option F1 General Help F10 Save and Exit ESC Exit 4-31

102 Boot Settings Boot Device Priority Removable Drives Boot Settings Configuration Security Select Screen Select Item Enter Go to Sub-screen F1 General Help F10 Save and Exit ESC Exit 4-32

103 Boot Device Priority 1st Boot Device 2nd Boot Device 3rd Boot Device [1st FLOPPY DRIV] [PM-ST320413A] [PS-ASUS CD-S340] Boot Device Priority 1st Boot Device 2nd Boot Device [PM-ST320413A] [PS-ASUS CD-S340] 4-33

104 Boot Settings Configuration Quick Boot Full Screen Logo Add On ROM Display Mode Bootup Num-Lock PS/2 Mouse Support Typematic Rate Wait for F1 If Error Hit DEL Message Display Interrupt 19 Capture [Enabled] [Enabled] [Force BIOS] [On] [Auto] [Fast] [Enabled] [Enabled] [Disabled] 4-34

105 Security Settings Supervisor Password User Password : Not Installed : Not Installed Change Supervisor Password Boot Sector Virus Protection [Disabled] 4-35

106 Security Settings Supervisor Password User Password Change Supervisor Password User Access Level Change User Password Clear User Password Password Check : Installed : Not Installed [Full Access] [Setup] Select Screen Select Item +- Change Option F1 General Help F10 Save and Exit ESC Exit 4-36

107 Exit Options Exit & Save Changes Exit & Discard Changes Discard Changes Load Setup Defaults Exit system setup after saving the changes. F10 key can be used for this operation. 4-37

108 4-38

109

110

111 5-1

112 5-2

113 5-3

114 5-4

115 5-5

116 5-6

117 5-7

118 5-8

119 5-9

120 CD ON/OFF PLAY/PAUSE STOP/EJECT PREVIOUS NEXT VOL. DOWN VOL. UP Esc F1 F2 F3 F4 F5 F6 F7 F8 CD ON/OFF CAPS LOCK LED SCROLL LOCK LED PLAY/PAUSE STOP/EJECT PREVIOUS NEXT VOL. DOWN VOL. UP 5-10

121 5-11

122 5-12

123 5-13

124 5-14

125 5-15

126 5-16

127 5-17

128 5-18

129 5-19

130 5-20

131 MBFastTrak378 (tm) BIOS version 1.00 (c) Promise Technology, Inc. All Rights Reserved. No Array defined... Press <Ctrl-F> to enter FastBuild (tm) Utility Or press <ESC> key to continue booting. FastBuild (tm) Utility 2.00 (c) Promise Technology, Inc. [ Main Menu ] Auto Setup [ 1 ] View Drive Assignments.... [ 2 ] Define Array [ 3 ] Delete Array [ 4 ] Rebuild Array [ 5 ] [ Keys Available ] Press 1..5 to select Option [ESC] Exit 5-21

132 FastBuild (tm) Utility 2.00 (c) Promise Technology, Inc. [ Auto Setup Options Menu ] Optimize Array for: Performance [ Array Setup Configuration ] Mode... Stripe Spare Drive... 0 Drive(s) Used in Array... 2 Array Disk Capacity (size in MB) [ Keys Available ] [ ] Up [ ] Down [,,Space] Change Option [ESC] Exit [CTRL-Y] Save 5-22

133 FastBuild (tm) Utility 2.00 (c) Promise Technology, Inc. [ Auto Setup Options Menu ] Optimize Array for: Security [ Array Setup Configuration ] Mode... Mirror Spare Drive... 0 Drive(s) Used in Array... 2 Array Disk Capacity (size in MB) [ Keys Available ] [ ] Up [ ] Down [,,Space] Change Option [ESC] Exit [CTRL-Y] Save Do you want the disk image to be duplicated to another? (Yes/No) Y - Create and Duplicate N - Create Only Array has been created. <Press any key to reboot> 5-23

134 Do you want the disk image to be duplicated to another? (Yes/No) Y - Create and Duplicate N - Create Only Start to duplicate the image... Do you want to continue? (Yes/No) Y - Continue N - Abort 5-24

135 5-25

136 FastBuild (tm) Utility 2.00 (c) Promise Technology, Inc. [ Rebuild Array Menu ] Array No RAID Mode Total Drv Capacity Status Array 1 Mirror/Stripe Critical Array Array Array [ Keys Available ] [ ] Up [ ] Down [ESC] Exit [Enter] Select FastBuild (tm) Utility 2.00 (c) Promise Technology, Inc. [ View Array Definition Menu ] Array No RAID Mode Total Drv Status Array 1 Mirror/Stripe 4 Critical Stripe Block: Not Available Gigabyte Boundary: ON [ Select Drive for Rebuild ] Channel: ID Drive Model Capacity (MB) 3:Mas FUJITSU MPD3043AT 4325 [ Keys Available ] [ ] Up [ ] Down [ESC] Exit [Enter] Select 5-26

137 \ \ 5-27

138 Copyright(C) 2003 Intel Corporation. All Rights Reserved. v3.x.x.xxxx [ MAIN MENU ] 1. Create RAID Volume 2. Delete RAID Volume 3. Reset Disks to Non-RAID 4. Exit RAID Volumes: None defined. [ DISK/VOLUME INFORMATION ] Non-RAID Disks: Port Drive Model Serial # Size Status Bootable 0 ST380013AS xxxxxxxx 74.5GB Normal Yes 1 ST380013AS xxxxxxxx 74.5GB Normal Yes [ ]-Select [ESC] Exit [Enter]-Select Menu Copyright(C) 2003 Intel Corporation. All Rights Reserved. v3.x.x.xxxx [ CREATE ARRAY MENU ] Name: RAID_Volume1 RAID Level: RAID0(Stripe) Strip Size: 128KB Capacity: 149.0GB Create Volume [ HELP ] Enter a string between 1 and 16 characters in length taht can be used to uniquely identify the RAID volume. This name is case sensitive and can not contain special characters. [ ]-Change [TAB]-Next [ESC] Previous Menu [Enter]-Select 5-28

139 Are you sure you want to create this volume (Y/N) Copyright(C) 2003 Intel Corporation. All Rights Reserved. v3.x.x.xxxx [ DELETE ARRAY MENU ] Name Level Drives Capacity Status Bootable RAID_Volume1 RAID0(Stripe) GBNormal Yes [ HELP ] Deleting a volume will destroy the volume data on the drive(s) and cause any member disks to become available as non-raid disks. WARNING:EXISTING DATA WITHING THIS VOLUME WILL BE LOST AND NON-RECOVERABLE [ ]-Change [TAB]-Next [<ESC>]-Previous Menu [<DEL>]-Delete Volume 5-29

140 [ VOLUME DELETE VERIFICATION ] Are you sure you want to delete this volume? ALL DATA IN THE VOLUME WILL BE LOST!! Are you sure you want to delete volume "RAID_Volume1"? (Y/N) Copyright(C) 2003 Intel Corporation. All Rights Reserved. v3.x.x.xxxx [ MAIN MENU ] 1. Create RAID Volume 2. Delete RAID Volume 3. Reset Disks to Non-RaID 4. Exit RAID Volumes: None defined. [ DISK/VOLUME INFORMATION ] Non-RAID Disks: Port Drive Model Serial # Size Status Bootable 0 ST380013AS xxxxxxxx 74.5GB Normal Yes 1 ST380013AS xxxxxxxx 74.5GB Normal Yes [ ]-Select [ESC] Exit [Enter]-Select Menu [ RESET ALL DATA RAID DATA ] Resetting all RAID data will remove any internal RAID structures from all RAID disks, including disks with working volumes. These structures are used to maintain the RAID volumes. By removing these structures, the drive will revert back to a Non-RAID disk that can then be used or reallocated to a new RAID volume. WARNING: Selecting "Yes" will cause all data on any RAID disk (RAID Volume or Other RAID Disk) to be lost. Are you sure you want to destroy all RAID data (Y/N): 5-30

141 \ \ \ \ \ \ \ \ \ \ \ \ \ \ \ 5-31

142 5-32