Installation Instructions v1.2

Transcription

1 Installation Instructions v1.2 The [VIVE N CHILL] is easy to install under a minute. It is non-permanent on the headset if you decide to move it or need to remove it for any reason. Both Standard and Deluxe Audio Headstrap (DAS) as well as Vive Pro install instructions are listed below. Vive Standard and DAS 1. First clean the mounting surface of the Vive where the [VIVE N CHILL] will mount by wiping it with a moist towelette or damp cloth to remove any grease or residue on the adhesive surface. Let it dry. 2. Carefully slide forward the front accessory door of the Vive. There are two tabs on either side of the interior and there will be tension from the cabling so make sure you clear the tabs completely. Fig.1 3. With the [VIVE N CHILL] held underneath the top head strap, route the USB power cable through the hole in the top of the door and plug into the USB accessory port. 4. Route the switch up through the hole in the harness and bring it forward so it rests on the Vive cables (if you have the DAS installed on the head strap) with the button facing outward. 5. Carefully slide the Vive door back into place. 6. Test fit the fan mounts with the fans at 90 degrees. You should find the sweet spot where the contour fits the headset and the location should be similar to the pictures below. 7. Remove the adhesive backing on the mounts and take your time aligning them to both sides of the headset where you ve decided to place them. They should face slightly inward toward the center. 8. Standard head strap: Use the provided Velcro strap or ziptie to hold the switch to the cabling. 9. DAS: If you have the DAS we recommend the Velcro tie to hold the switch to the head strap and a zip tie on the right side to hold the 3-1 cable to the side of the strap. Route cabling on top of the right fan mount and keep it low where it doesn't interfere with airflow or folding. Use the strap to prevent the cable from putting pressure against the mount when cabling expands or contracts. Figure 1. Opening Accessory Door.

2 Figure 2. Re-installing accessory Door.

3 Figure 3. Ideal mount location Figure 4. Affixing Velcro tie to cabling. Standard head strap.

4 Figure 5. DAS: Velcro tie on head strap. Figure 5. DAS. Velcro or zip tie on 3in1 cable to the right side head strap.

5 Figure 6. Keep 3in1 cabling below airflow. Vive Pro *This install requires a USB to USB C adapter available here. 1. First clean the mounting surface of the Vive Pro where the [VIVE N CHILL] will mount by wiping it with a moist towelette or damp cloth to remove any grease or residue on the adhesive surface. Let it dry. 2. Test fit the fan mounts with the fans at 90 degrees. You should find the sweet spot where the contour fits the headset and the location should be similar to the pictures below. 3. Remove the adhesive backing on the mounts and take your time aligning them to both sides of the headset where you ve decided to place them. They should face slightly inward toward the center. 4. Use the provided Velcro strap to hold the switch to the head strap. 5. Peel off the face cushion starting from both ends until it detaches from the headset. Fig Carefully pry open the cover from its flap. Pull the cover out to access the ports on the headset. Fig Insert the USB C Adapter connector to the USB Type-C port on the headset and route the adapter cable above and behind display cable. Fig Align and push the tabs of the compartment cover onto their corresponding holes. Fig The adapter should sit as in Fig. 12 and you should be able to fully retract the lens inward to have maximum FOV. 10. Connect USB to USB C Adapter. Route USB cable below left fan cable. Push adapter below Fan so it s not in the airflow pathway. 11. Replace the face cushion by inserting its tab into the slot on the headset, and then aligning the hook and loop strips. Enjoy the added comfort of high intensity gaming with the [VIVE N CHILL]! Fig. 14 *Due to the design of the Vive Pro and DAS head mount, there is more vibration transferred to the headphones and increased noise profile. This should fade away in high intensity gaming but we recommend shutting off the [VIVE N CHILL] when you don t need it to eliminate any unwanted noise.

6 Figure 7. Remove Foam Face Pad Figure 8. Remove compartment Cover Figure 9. Insert USB C Adapter

7 Figure 10. Route Adapter cable above and behind display cable Figure 11. Replace Cover

8 Figure 12. Cover Replaced. Make sure FOV can be fully retracted. Figure 13. Connect USB to USB C Adapter. Route USB cable below left fan cable. Push Adapter below Fan.

9 Figure 14. Replace the face cushion