EMULATOR IMMO RENAULT
|
|
- Tyler Stanley
- 6 years ago
- Views:
Transcription
1 1 EMULATOR IMMO RENAULT
2 2 5 NR Renault Clio 1,2 petrol with one probe lambda (gel) Syrius 32 without CAN Syrius 34 1,4 1,6 2,0 EMS ,9 2,2 and 2,5 Dci without CAN 1,5 Dci without CAN 1,9 Dti 1 plug 1,9 Dti 2 plugs 1,9 Diesel DCU3 2,8 Td 3,0 gasoline 1 plug
3 3 Thank you for purchasing our device. Emulator immo to Renault cars replaces damaged immobilizer or the car key. It function after made changes in memory content of Engine Control Module ECM. In case of losing the car keys or a car burglary, it enable to drive off from the road to the car service. Due to a low cost you can leave it in the car instead of buying a new immo or making car keys duplicate. Two LEDs indicating: green - power red transmission (it is blinking all the time).
4 4 ECU 1,2 (gel) C-1uF R-100 Dz-3V8 Break out PIN in plug where we connect the unblocker. C- connect one leg to plus 5V and second to 27 th leg of unit.
5 5 Syrius 32 without CAN In ECM Syrius 32 is a flash 29f200 or 29f400.
6 6 From 4000 to 7FFF In the addresses from 4000 to 7FFF find values 64 C7 and change these values everywhere and two units before them into FF FF FF FF. Do it in the whole map from 4000 to 7FFF!!!
7 7 Connecting emulator to ECM: +12V ACC 29pin CODE 58pin GROUND 3pin cut off 58pin from plug!!!
8 8 If transducer CAN A82C250 is on the plate in the computer, the ECM will not work with emulator!!!
9 9 Syrius 34 1,4 1,6 2,0 In ECM Syrius 34 is flash 29f200 or 29f400. To fit to the emulator, all the contents need to be replaced into files Syrius 34 1,4 1,6 or 2,0.
10 10 Power for the emulator take from the capacitor at the flash.
11 11 EMS 3132 In the EMS3132 drivers is flash 29f200 or 29f400.
12 12 In the addresses from 4000 to 7FFF find values 64 C7 and change these values everywhere and two units before them into FF FF FF FF. Do it in the whole map from 4000 to 7FFF!
13 13 Power for the emulator take from the capacitor at the flash.
14 14 Connect emulator as pictured by unsoldering the capacitor. Connect to the point which goes to the processor.
15 15 1,9 2,2 and 2,5 Dci without CAN Renault Laguna 1,9 Dci 1999 year mechanical ignition switch.
16 16 In memory 5P08C3 in the addresses: 003E, 003F, 0040, 0041 and 0044, 0045, 0046, 0047 type FF.
17 17 In ECM, immo line (code) of emulator solder to the point as pictured.
18 18 Power for the emulator take from the capacitor on the driver plate.
19 19 Remove resistor 334. Turn on the ignition for 30 seconds, turn it off for 30 seconds and repeat it a few times.
20 20 1,5 Dci without CAN Unlock version without odometer. Replace content of and connect emulator, immo line is 10 pin of processor, visible in the photo, which must be held up. Power take from capacitor at the memory. Add injectors and settings by Clip or Launch.
21 21 1,9 Dti 1 plug Renault Megane 1,9 Dti
22 22
23 23
24 24 The immo line of emulator connect to the 59 pin of the driver. Cut off this pin from ECM.
25 25 GND and ACC connect to LED in the driver.
26 26 1,9 Dti 2 plugs Renault Megane 1,9 Dti In memory 24c04 type 8C FF from 174 to 177 and 1B7 to 1BA. Connecting emulator in the driver: GND (brown) pin 4, 5 ACC (black) pin 81 immo line (white) pin 15
27 27
28 28 Cut off pin 15 from wiring!!!
29 29 1,9 Diesel DCU3 Renault Kango 1,9 Diesel 2001 In memory change into FF addresses from 00 to 0D and 80 to 8D. In the driver the code line of emulator connect to pin 20. This pin must be cut off from the car wiring. GND pin 78 and ACC pin 77 must be connected to the wiring or to the driver.
30 30 Mascot 2,8 Td In memory 24c16 change from 040 to 1FF into FF.
31 31 Connecting emulator in the driver:
32 32 CUT OFF pin CODE OF THE DRIVER FROM THE WIRING!!!
33 33 Laguna 3,0 gasoline 1 plug, memory 24c02 CUT OFF pin 50 OF THE DRIVER FROM THE WIRING!!! Connecting the emulator: ACC pin 37 ground pin 24 immo pin 50
34 34 In order to use emulator, in memory 24c02 from 05A to 05F write values FF and from 0F2 to 0F7 write values FF.
35 35 Warning!!! Due to possible construction changes of the cars, before connecting the device check signals by multimeter on the immobilizer plug or in ECM.
See all emulators Program Use
1 Program Renault Use Sirius 32 / Sirius 34 without CAN EMS 3132 / EMS 3134 without CAN 1.9 2.2 and 2.5 dci without CAN Delphi DDCR 1.9 dti 1 plug 1.9 dti 2 plugs 1.9 diesel DCU3 2.8 TD 1 plug with 24C02
More informationUniversal emulator UNIEMU user manual
Universal emulator UNIEMU user manual 1. Mercedes Benz Seat Occupant sensor emulator - Type1: not included Can emulate only Mercedes Benz E-class W211, CLS W219 (2004-2007) with BOSCH airbag computers
More informationJulie - Universal Car Emulator Programs:
1 Julie - Universal Car Emulator Programs: Suzuki with X24C01 memory...3 Suzuki with OKI and 24C04 memory...3 Suzuki with 93C56 memory...9 Program Use Suzuki with X24C01 memory Suzuki with X24C01 memory
More informationBehringerMods.com. Instructions for modification of Behringer SRC analog inputs and outputs
BehringerMods.com Instructions for modification of Behringer SRC analog inputs and outputs The following instructions will cover the details of fully modifying a unit with analog output and analog input
More informationRenault CAN/K-line ECU Tool V1.03
Renault CAN/K-line ECU Tool V1.03 User manual Revision D May 2012 1. Introduction Renault CAN/K-line ECU Tool is an OBDII tool with various engine control unit internal memory modification functions, such
More informationTraining Instruction
Training Instruction Contents Section 1. Car security:...3 Car lock, ignition switch... 3 Steering wheel lock... 3 Car alarm... 4 Non serial immobilizer... 4 GPS - Global Positioning System... 5 Steering
More informationPIEXX UT36 px Installation Instructions
PIEXX UT36 px Installation Instructions The PIEXX UT-36 px is a physical and electrical replacement for the original ICOM UT-36 speech synthesizer. UT-36 px Installation The UT-36 px speech synthesizer
More informationABRITES Diagnostics for Renault. User Manual
Abritus 72 Ltd. Date: 01-June-2013 ABRITES Diagnostics for Renault User Manual Version: 2.1 issued by: Abritus 72 Ltd ABRITES DIAGNOSTICS FOR RENAULT 5.X Document number 1/20081111 Date: 01.06.2013 List
More informationFor Auto Locksmith Association only!!! Emergency Service Manual.
For Auto Locksmith Association only!!! Emergency Service Manual = OBD Key Programmer + OBD Alarm Disarming tool = ====================================================================== Models: AUDI A4
More information1320 Electronics LLC USB-ALDL Cable User s Guide Electronics LLC. User s Guide for: USB-ALDL Cable
1320 Electronics LLC User s Guide for: USB-ALDL Cable 1 Contents Warnings 3 Specifications 4 Configuration 5 Automatic Driver Installation 6 Manual Driver Installation 7 Driver Installation Verification
More informationLab 3: Building a Power Supply and a Stereo Amplifier
ECE 212 Spring 2010 Circuit Analysis II Names: Objectives Lab 3: Building a Power Supply and a Stereo Amplifier In this lab exercise you will build a regulated variable-voltage power supply and a 10-watt
More informationR-DAS Tiny User s Manual
R-DAS Tiny User s Manual Scope This document is an addendum to the R-DAS manual and is specific to the R-DAS Tiny (hardware V4.x). For general concepts about the R-DAS, please see the R-DAS Manual. New
More informationABRITES Diagnostics for Renault/Dacia User Manual
Version: 2.7 www.abrites.com Manual version: 2.7 1 List of Revisions Date Chapter Description Revision 11.11.2008 Release version of the document 1.0 18.03.2009 Update to V1.1 of the software 1.1 17.06.200
More informationRevision B, February 14, Copyright 2009, Elecraft, Inc. All Rights Reserved
K3 EXTERNAL ALC MODIFICATION Revision B, February 14, 2009 Copyright 2009, Elecraft, Inc. All Rights Reserved Introduction MCU firmware release from 1.99 with DSP firmware release from 1.76 provide the
More informationHigh Power (15W + 15W) Stereo Amplifier
High Power (15W + 15W) Stereo Amplifier Build Instructions Issue 1.0 Build Instructions Before you put any components in the board or pick up the soldering iron, just take a look at the Printed Circuit
More informationChill Interface PCB Assembly Instructions
ExcelValley Chill Interface PCB Waveblaster Module MIDI Interface Board Chill Limited Edition V2 Assembly Kit Standalone midi interface board for Waveblaster synthesizer modules. Suitable for most Waveblaster
More informationAdBlue Emulator V4 NOx
AdBlue Emulator V4 NOx Programming manual Attention! Always connect the ground cable first! Otherwise, you can burn the emulator module or damage the SCR / NOx module of the truck! AdBlue Emulator V4 NOx
More informationEZ-TAG2 Manual_Layout 5 11/12/ :14 Page 1 U S E R M A N UAL
EZ-TAG2 Manual_Layout 5 11/12/2012 09:14 Page 1 USER MANUAL EZ-TAG2 Manual_Layout 5 11/12/2012 09:14 Page 2 Contents EZ-TAG2 and Back Plate 1 x Security Torx Key 4 x Screws and raw plugs 1 x Marking out
More informationBuffaloLabs WiFi Lantern Assembly guide version 1
BuffaloLabs WiFi Lantern Assembly guide version 1 Needed equipment: Solder iron Solder wire Cutter Wire stripper (optional) Hot glue gun Overview of the components (not including USB cable and box panels)
More informationColecovision 5v Memory Mod Installation
Colecovision 5v Memory Mod Installation The Colecovision suffers from common failure points: the power supply, power switch, and 4116 DRAM. The power supply suffers from poor soldering, the power switch
More informationMicro USB Lamp Kit ESSENTIAL INFORMATION. Version 2.0 DESIGN A STYLISH LAMP WITH THIS
ESSENTIAL INFORMATION BUILD INSTRUCTIONS CHECKING YOUR PCB & FAULT-FINDING MECHANICAL DETAILS HOW THE KIT WORKS DESIGN A STYLISH LAMP WITH THIS Micro USB Lamp Kit Version 2.0 Build Instructions Before
More informationVagtacho v5.0. Start software, select "VDO NEW - CAN - UDS protocol" from menu. Press "Connect Selected ECU" button, after
Vagtacho v5.0 How to program new transponder keys with Vagtacho! This procedure works with VDO dashes on CAN bus (UDS protocol) from year 2009-2011 1. Switch ON ignition with VALID key! Start software,
More informationBluetooth Keyless Entry System - Lite
Bluetooth Keyless Entry System - Lite Installation and operation manual DISCLAIMER: To aid users during the installation process, WE STRONGLY RECOMMEND THAT THIS MANUAL IS READ FIRST before beginning the
More informationControl Box Setup - PRSalpha
888-680-4466 ShopBotTools.com Control Box Setup - PRSalpha Copyright 2016 ShopBot Tools, Inc. page 1 Copyright 2016 ShopBot Tools, Inc. page 2 Parts List: Hooking Up a PRSalpha Gantry Tool Powering the
More informationSierra Radio Systems. Digital Compass. Reference Manual. Version 1.0
Sierra Radio Systems Digital Compass Reference Manual Version 1.0 Contents Digital compass board RS485 power injector For more information, go to the Sierra Radio Systems web site at www.sierraradio.net
More information1/Build a Mintronics: MintDuino
1/Build a Mintronics: The is perfect for anyone interested in learning (or teaching) the fundamentals of how micro controllers work. It will have you building your own micro controller from scratch on
More informationUpgrading to a RBK Control Box
Page 1 Upgrading to a RBK Control Box ShopBot Tools, Inc. Technical Support 3333-B Industrial Drive, support @shopbottools.com Durham NC 27704 1-888-680-4466 ShopBotTools.com Page 2 Revision History Date:
More informationShapeoko and the Triquetra 3 Axis Touch Plate
Shapeoko and the Triquetra 3 Axis Touch Plate The Triquetra Touch Plate will work with the Shapeko3, however your version of Carbide Motion software may not work with 3 axis zeroing. To get around this
More informationAssembly Guide. LEDs. With these assembly instructions, you can easily build your own SWT16. All required components are included in this kit.
Assembly Guide With these assembly instructions, you can easily build your own SWT16. All required components are included in this kit. You need the following tools: soldering iron, wire cutter and solder.
More informationSchematic Diagram: R2,R3,R4,R7 are ¼ Watt; R5,R6 are 220 Ohm ½ Watt (or two 470 Ohm ¼ Watt in parallel)
Nano DDS VFO Rev_2 Assembly Manual Farrukh Zia, K2ZIA, 2016_0130 Featured in ARRL QST March 2016 Issue Nano DDS VFO is a modification of the original VFO design in Arduino Projects for Amateur Radio by
More informationModifying the Motorola DTMF Microphone For 16 Button Operation James L. Reese WD5IYT May 10, 2002
Modifying the Motorola DTMF Microphone For 16 Button Operation James L. Reese WD5IYT May 10, 2002 The Motorola DTMF microphone is easily modified to produce all 16 DTMF tones. This modification involves
More informationBack to Main. Trade Show. iscan-ii / D91 Latest Versions (March, 2009)
Back to Main Trade Show iscan-ii / D91 Latest Versions (March, 2009) iscan-ii RENAULT V1.02 English/Chinese/Japanese 2009-03-02 iscan-ii CITROEN V1.02 English/Chinese/Japanese 2009-03-02 iscan-ii PEUGEOT
More informationButton Code Kit. Assembly Instructions and User Guide. Single Button Code Entry System
Button Code Kit Single Button Code Entry System Assembly Instructions and User Guide Rev 1.0 December 2009 www.alan-parekh.com Copyright 2009 Alan Electronic Projects Inc. 1. Introduction... 4 1.1 Concept
More informationSMM501/501-H (Surveillance Mode Module) Ford Police Interceptors (Sedan and SUV)
An ISO 9001:2008 Registered Company SMM501/501-H (Surveillance Mode Module) 2013-2014 Ford Police Interceptors (Sedan and SUV) Introduction The SMM501/501-H is intended for 2013 and 2014 Ford Police Interceptors
More informationDIY Line Tracking Smart Car with AT89C2051
DIY Line Tracking Smart Car with AT89C2051 1. Introduction: A DIY Smart Car design involves mechanical structure, electronic based sensor principle, automatic control, and even knowledge of microcontroller
More informationCopyright st Call Lockouts Ltd Author: Richard Bunn Product: Touchclone
Eeprom Work for Beginners Why would you undertake Eeprom work? Ok so you have found that your OBD programmer does not work on this make and model of vehicle. What do you do next? Do you just walk away
More informationsolutions for teaching and learning
Circuit Construction Op-Amp Comparator Project The circuit diagram on the right is the circuit for your project, it is called an op-amp comparator circuit, it is called a comparator circuit as it compares
More informationDENTRON CLIPPERTON-L POWER SUPPLY MODULE v5.3 ASSEMBLY & INSTALLATION INSTRUCTIONS
DENTRON CLIPPERTON-L POWER SUPPLY MODULE v5.3 ASSEMBLY & INSTALLATION INSTRUCTIONS WARNING: This upgrade is not for the faint of heart or inexperienced in amplifier theory and repairs as the voltages inside
More informationNistune Type 1 Diagnostics Technical Notes V1.2 (JECS ECCS Legacy Engine Control Units)
Nistune Type 1 Diagnostics Technical Notes V1.2 (JECS ECCS 1984-1989 Legacy Engine Control Units) Copyright 2004, 2005, 2006, 2014 Nistune Developments WARNING If your ECU pulses the fuel pump, injectors,
More informationRECORD & PLAYBACK KIT
ESSENTIAL INFORMATION BUILD INSTRUCTIONS CHECKING YOUR PCB & FAULT-FINDING MECHANICAL DETAILS HOW THE KIT WORKS ADD AN AUDIO MESSAGE TO YOUR PRODUCT WITH THIS RECORD & PLAYBACK KIT Version 2.1 Build Instructions
More informationCHAPTER 5. Voltage Regulator
CHAPTER 5 Voltage Regulator In your robot, the energy is derived from batteries. Specifically, there are two sets of batteries wired up to act as voltage sources; a 9V battery, and two 1.5V batteries in
More informationLushOne Inca Synth Module Build Instructions
LushOne Inca Synth Module Build Instructions Getting started If you can build the LushOne base module then then building the Inca should be easy Remember: Accuracy and neatness is more important than speed
More informationPart 2: Building the Controller Board
v3.01, June 2018 1 Part 2: Building the Controller Board Congratulations for making it this far! The controller board uses smaller components than the wing boards, which believe it or not, means that everything
More informationALDL Bluetooth Adapter
1320 Electronics LLC for: ALDL Bluetooth Adapter Contents Warnings 3 Specifications 4 Quick Start Instructions 5 Installing the 'ALDL Bluetooth adapter' 6 Operating the ALDL Bluetooth Adapter 7 Bluetooth
More information**** Never plug in your LED driver to AC power until all wiring is complete ****
1 RapidLED Plug-n-Play Solderless Retrofit Kit Contents Overview... 1 Warnings Read Me First!... 1 Dimmable Driver Controller and Driver Output Current Adjustment... 2 Kit Assembly... 2 Attaching Your
More informationInstallation and programming instructions for STAG TUNING
Installation and programming instructions for STAG TUNING ver. 1.3 2016-12-15 CONTENTS 1. Principle of operation... 2 2. Installation instructions... 2 3. Description of terminals... 3 4. Using the software...
More informationTubbutec SH-1oh1 µtune
Tubbutec SH-1oh1 µtune Midi retrofit and feature extension for Roland SH-101 Installation Manual http://tubbutec.de 1 Contents Contents 2 1 Installation of the SH-1oh1 mod - µtune edition 3 1.1 Opening
More informationWIRING FOR MXL PRO- 05
CONSTRUCTIVE DOCUMENTATION 0/0/005 WIRING Notes: general-purpose wiring for MXL PRO 05 CAR/BIKE installation Version.00 WIRING FOR MXL PRO- 05 MXL PRO 05 wiring (CAR/BIKES) Logger pinout: 7 pins Deutsch
More informationBMC24. MIDI TO GATE CONVERTER DOCUMENTATION. This documentation is for use with the "Euro Style" bottom board.
BMC24. MIDI TO GATE CONVERTER DOCUMENTATION. This documentation is for use with the "Euro Style" bottom board. A. USING THE MIDI TO GATE CONVERTER B. PARTS LIST C. BUILDING INSTRUCTIONS D. SCHEMATICS Revision.
More informationLook closely at this schematic diagram, in thid class you will be asked to construct this circuit WITHOUT using the textbook!
LEARNING TO READ SCHEMATIC DIAGRAMS So far you have been constructing the circuits by following the detailed pictures in the textbook. For example, you were following the pictures to connect the LED between
More informationAiM User Manual. ECU Bridge. Release 1.09
AiM User Manual ECU Bridge Release 1.09 1 Introduction ECU Bridge has been designed and developed by AiM to allow SmartyCam to connect to your vehicle ECU, sample and show the data out coming from it.
More informationAssembly Instructions for 128x64 Graphics Display Unit
02/15/10 version 1.0 Assembly Instructions for 128x64 Graphics Display Unit This document describes the physical assembly of the Graphic Display unit for the 16 Bit Experimenter 128x64 Graphics kit. It
More informationALDL Bluetooth Adapter with USB (MK2)
1320 Electronics LLC for: ALDL Bluetooth Adapter with USB (MK2) Contents Warnings 3 Specifications 4 Quick Start Instructions 5 Installing the 'ALDL Bluetooth adapter' 6 Operating the ALDL Bluetooth Adapter
More informationTEMIC 51T (Temic) EMULATION
Note: To use with frequencies above 40Mhz it will be required to use an emulator board that has been specially modified to obtain high frequency operation and will work only with the POD-51Temic. The EPROM
More information3 pyro output datalogger altimeter with an ATmega 328 microcontroller Kit assembly instructions
3 pyro output datalogger altimeter with an ATmega 328 microcontroller Kit assembly instructions Version date Author Comments 1.0 29/05/2013 Boris du Reau Initial version Rocket Type Micro-max Model Mid
More informationW205-N RVC NTV-KIT703
3950 NW 120 th Ave, Coral Springs, FL 33065 TEL 561-955-9770 FAX 561-955-9760 www.nav-tv.com info@nav-tv.com W205-N RVC NTV-KIT703 Overview The W205-N RVC Kit interfaces a backup camera input (with active
More informationBOOSTBYSMITH S ECU FLASHING INTERFACE (Gen II Hayabusa)
BOOSTBYSMITH S ECU FLASHING INTERFACE (Gen II Hayabusa) Contact Information: Greg Smith www.boostbysmith.com greg@boostbysmith.com (517)743-3666 INDEX I. Hardware Included II. III. IV. ECU1.0 Basics Installation
More informationMITSUBISHI ECU FLASH REPROGRAMMER (Ver. 2.00) INSTRUCTION MANUAL
MITSUBISHI ECU FLASH REPROGRAMMER (Ver. 2.00) INSTRUCTION MANUAL !! NOTE and CAUTION!! Thank you for purchasing the TECHTOM Flash Reprogrammer. Please read and follow the instructions carefully to ensure
More informationOBD Auto Doctor. User Manual for ios (iphone and ipad) Copyright 2018 Creosys Ltd
OBD Auto Doctor User Manual for ios (iphone and ipad) Copyright 2018 Creosys Ltd User Manual for ios (iphone and ipad) 1. Introduction 1.1 Platform and Hardware Requirements 1.2 Supported Adapters 1.3
More informationInstalling the EFILive E38 / E67 ECM Ethanol Custom Operating System
Installing the EFILive E38 / E67 ECM Ethanol Custom Operating System Installing the EFILive E38 / E67 Ethanol Custom Operating System Copyright 1998-2009 EFILive Limited. All rights reserved First published
More informationEE 354 August 1, 2017 Assembly of the AT89C51CC03 board
EE 354 August 1, 2017 Assembly of the AT89C51CC03 board The AT89C51CC03 board comes as a kit which you must put together. The kit has the following parts: No. ID Description 1 1.5" x 3.25" printed circuit
More informationTRANSPRONICS OPERATING MANUAL CONTENTS 1- GENERAL INFORMATION 2- FEATURES 3- GENERAL OPERATION 4- PC PROGRAM OPERATION 5- SPECIAL FEATURE
TRANSPRONICS OPERATING MANUAL CONTENTS 1- GENERAL INFORMATION 2- FEATURES 3- GENERAL OPERATION 4- PC PROGRAM OPERATION 5- SPECIAL FEATURE 6- SOFTWARE UPDATING 1 1- GENERAL INFORMATION The professional
More informationManual Version March 2007
Manual Version 1.1 - March 2007 Page 1 Table of Contents Section1: 6922 Line Board Build... 3 6922 Line Board Version Notes... 5 6922 Line Board Build - HARD-WIRED VERSION... 5 Final Connections and Checks
More informationsolutions for teaching and learning
RKOneAnalogue Component List and Instructions PCB layout Constructed PCB Schematic Diagram RKOneAnalogue Software Development PCB Page 1 Description The RKOneAnalogue software development PCB has been
More informationX-431 Volkswagen Diagnosis. Table of Contents INTRODUCTION...1
Table of Contents INTRODUCTION...1 FEATURES...1 Advanced...1 Open...1 Integrative...1 Flexible...1 HARDWARE CONFIGURATION...2 PORTS AND INDICATORS...3 PRINTER OPERATION...4 Mounting Paper...4 Printing
More informationAttention: The connectors on the BMD16N are not normal network plugs. Never connect the decoder to a PC or any other network device!
BMD16N version 1.2 Feedback decoder with 16 contacts for the S88-bus Compatible with a.o. Märklin Digital, Uhlenbrock Intellibox, Fleischmann Twin-Center and LDT HSI-88 Compatible with the s88-n standard
More informationIssue : 1.1 Date : 19/1/2004. Trigger IO. C-Cam Technologies. a division of. Vector International 1 / 6
Trigger IO C-Cam Technologies a division of Vector International 1 / 6 1 Trigger IO connector Trigger IO connector Camera with LS interface Trigger IO connector Camera with USB interface 2 / 6 1.1 Pin
More informationConect 121 Upgrade. Copyright 2013 Conqueror Design and Engineering Ltd.
All rights reserved. Any dispute about the use of this software and/or hardware or of these terms and conditions shall be resolved or arbitrated under English Law. Manuals and accompanying documentation
More informationCONSOLE CONNECTOR KIT 9501 INSTALLATION INSTRUCTIONS
CONSOLE CONNECTOR KIT 9501 INSTALLATION INSTRUCTIONS FOR USE WITH: HAMMOND Organ Models L-100, M-100 Series, M-l, M-2, M-3 LESLIE Speaker Models 760, 770, 825 KIT CONTENT Console Connector Assembly 043075
More informationChapter 1 Getting Started
Chapter 1 Getting Started Installation Instructions 1.1 Subject The NEO AUX adapter an integration between an MP3 player and a factory installed car stereo. Equipped with the specific vehicle harness and
More informationMP3 audio amplifier. Build Instructions. Issue 2.0
MP3 audio amplifier Build Instructions Issue 2.0 Build Instructions Before you put any components in the board or pick up the soldering iron, just take a look at the Printed Circuit Board (PCB). The components
More informationPhi-panel backpack assembly and keypad options Dr. John Liu 12/16/2012
Phi-panel backpack assembly and keypad options Dr. John Liu 12/16/2012 1. Introduction:... 3 Currently available:... 3 2. Backpack assembly... 4 3. Connecting to a keypad... 6 4. Rotary encoder keypads...
More informationAiM Infotech. Marelli SRA SRAE SRT small version ECU. Release 1.01
AiM Infotech Marelli SRA SRAE SRT small version ECU Release 1.01 1 Supported models This tutorial explains how to connect Marelli ECUs to AiM devices. Supported models are: SRA SRAE SRT small version small
More informationInstallation instructions DC Protection and Delay unit, Version 1.2 The package should contain: A piece of normal gauge yellow wire for the AC connect
Installation instructions DC Protection and Delay unit, Version 1.2 How does the unit work? Delay: Basically a capacitor is charged via a resistor, when the voltage of the capacitor reach a certain level,
More informationTM LOCKPICK C8 INSTALLATION OPTIONS COPYRIGHT 2011 COASTAL ELECTRONIC TECHNOLOGIES, INC. UNPLUG ORIGINAL RADIO CONNECTORS THEN PLUG IN HERE
TM LOCKPICK C8 INSTALLATION OPTIONS COPYRIGHT 2011 COASTAL ELECTRONIC TECHNOLOGIES, INC. FACTORY CONNECTORS INCLUDED UNPLUG ORIGINAL RADIO CONNECTORS THEN PLUG IN HERE PLUG AND PLAY NO OTHER CONNECTIONS
More informationNext thing you want to check for is if the truck has an aftermarket key fob or security system or satellite radio. If you are not sure, please check
Next thing you want to check for is if the truck has an aftermarket key fob or security system or satellite radio. If you are not sure, please check the back of the OBD port for a PURPLE wire. Follow that
More informationLCx-xxxAx-8.08 Linear. Installation. Contents. Mounting: Short Instruction LCx-xxxAx Connecting Power and Signal
LCx-xxxAx-8.08 Linear Contents Installation pg1-3 Mounting Wiring Connecting Power and Signal Operation pg4-6 DIP Switch settings Controlling the Actuator Power Settings pg5 Signal loss and Calibration
More informationFVT/FVR20D2I1C4E INSTALLATION AND OPERATION MANUAL
2-CHANNEL 10-BIT DIGITALLY ENCODED VIDEO + 2 BI-DIRECTIONAL DATA + AIPHONE INTERCOM + 4 CONTACT CLOSURE + 100MB ETHERNET + REDUNDANT POINT-TO-POINT DUAL SFP OPTICAL PORTS The series utilize 10-bit digital
More informationW DYNAMIC Kit NTV-KIT461
3950 NW 120 th Ave, Coral Springs, FL 33065 TEL 561-955-9770 FAX 561-955-9760 www.nav-tv.com info@nav-tv.com W204-12 DYNAMIC Kit NTV-KIT461 Overview The W204-12 DYNAMIC kit allows the user to add up to
More informationSRI-02 Speech Recognition Interface
SRI-02 Speech Recognition Interface Data & Construction Booklet The Speech Recognition Interface SRI-02 allows one to use the SR-07 Speech Recognition Circuit to create speech controlled electrical devices.
More informationWind Logger Shield. Parts included: Date: 29/07/14 Version: 1.0 By: Matt Little
Wind Logger Shield Date: 29/07/14 Version: 1.0 By: Matt Little Parts included: This is a simple shield to easily implement a wind resource data logging system. It is designed to read 2 x pulse type anemometers
More informationCygnos360 V2 Installation Manual
VERSION 1.0. - OKTOBER, 2009 www.cygnos360.com Contents: 1. What you need...2 1.1. Tools...2 2. Preparation...3 2.1. Preparing the solder points...3 3. Installing in your Xbox360...4 3.1. Installing the
More informationMaxi-K. Installation and user manual 1.16 English
Maxi-K Installation and user manual 1.16 English 1 1 INTRODUCTION The Maxi-K unit is used for extension of maxidot functions. It was primarily built for Skoda Octavia 1U, but it works also on VW Golf IV,
More informationDEFAULT SCREEN. Button and Screen Layout DRILLING WIDTH TARGET RATE HOPPER NUMBER CROP NAME DRILLING ACTION CROP NUMBER. HOPPER selection POWER On/Off
DEFAULT SCREEN Button and Screen Layout DRILLING WIDTH TARGET RATE CROP NAME HOPPER NUMBER DRILLING ACTION CROP NUMBER HOPPER selection POWER On/Off AREA / DISTANCE TARGET RATE Increase CROP Scroll / Up
More informationPhysics E-1bxl and PS3 Lab 4: Neuron Model 2016
I. Before coming to lab Read this handout. Also review the background supplemental for Lab 3:Digital Circuits especially the sections on breadboard layout, transistors, and LEDs. Carefully study the circuit
More informationAUDIO AMPLIFIER PROJECT
Intro to Electronics 110 - Audio Amplifier Project AUDIO AMPLIFIER PROJECT In this project, you will learn how to master a device by studying all the parts and building it with a partner. Our test subject:
More informationSharpSky Focuser Construction. SharpSky Focuser. Construction Document V st December 2012 Dave Trewren 1
SharpSky Focuser Construction Document V0.12 1st December 2012 Dave Trewren 1 Contents 1 General... 3 1.1 Change Record... 3 1.2 References... 3 2 Introduction... 5 3 SharpSky driver installation... 5
More informationBMS: Installation Manual v2.x - Documentation
Page 1 of 7 BMS: Installation Manual v2.x From Documentation This section describes how external peripheral devices are connected and additional functions of the BMS are used. I you have not done so already,
More informationrevolution How does the ibutton work? Full kit including PCB, PICAXE-08M chip and ibutton key. Spare ibutton Key
AXE109S LOG020 Full kit including PCB, PICAXE-08M chip and ibutton key. Spare ibutton Key The ibutton is an electronic chip armoured in a 16mm stainless steel can. Because of this unique, durable package,
More informationAccsense Wireless System. Temperature Monitor
Accsense Wireless System Temperature Monitor Contents 1. Installing the B1-06 Gateway...2 2. Installing the Pods...3 3. Wiring the Pods...5 Version 1 - August 2010 29975 Page 1 1. Installing the B1-06
More informationInstallation/assembly manual for DCC/Power shield
Installation/assembly manual for DCC/Power shield The DCC circuit consists of the following components: R1/R6 R2/R3 R4/R5 D1 C2 2 kω resistor ½ Watt (colour code Red/Black/Black/Brown/Brown) 10 kω resistor
More informationLab 2.2 Ohm s Law and Introduction to Arduinos
Lab 2.2 Ohm s Law and Introduction to Arduinos Objectives: Get experience using an Arduino Learn to use a multimeter to measure Potential units of volts (V) Current units of amps (A) Resistance units of
More informationOpenSprinkler v2.1u Build Instructions
OpenSprinkler v2.1u Build Instructions (Note: all images below are 'clickable', in order for you to see the full-resolution details. ) Part 0: Parts Check Part 1: Soldering Part 2: Testing Part 3: Enclosure
More informationTest Procedure for the NIS5101
1 Test Procedure for the NIS5101 09/06/2004 Board Description: The NIS5101 demo-board has several test points that are used to measure different device functions. The test procedure for each of the tests
More information[BINARY EDITOR] (DISTRIBUTED BY HICKLEYS)
Tel: 01823 328532 email: diagnostics@hickleys.com JADOOGAR: V2 [BINARY EDITOR] (DISTRIBUTED BY HICKLEYS) Elegance Lockmasters, 39 Green Lane, Ilford, Essex, IG11XG : TELE 0208 5143313 :Mob: 07930453650
More informationAHD 4CH HDD MOBILE DVR
AHD 4CH HDD MOBILE DVR Hardware User Manual (Nysus 6 & 7) 0 Catalogue Chapter 1 Accessories and Interface... 1 1.MDVR and accessories... 1 2.System connection... 2 3.Panel introduction... 3 4.Interfaces
More informationPost Tenebras Lab. Written By: Post Tenebras Lab
Post Tenebras Lab PTL-ino is an Arduino comptaible board, made entirely out of through-hole components. It is a perfect project to learn how to solder and start getting into the world of micro controllers.
More informationThursday, September 15, electronic components
electronic components a desktop computer relatively complex inside: screen (CRT) disk drive backup battery power supply connectors for: keyboard printer n more! Thursday, September 15, 2011 integrated
More informationActive Power Programmer Instructions
Active Power Programmer Instructions Installation 1. Before you install the software, DO NOT PLUG the devices usb port into your computer. You will be ask to do this later in the installation 2. Run the
More informationEnergy Meter and. Current Transducer. Assembly Manual
Energy Meter and Current Transducer Assembly Manual 2017 1 The energy meter assembly is made of two separate boxes and associated accessories, as follows: Energy Meter (EM) Box, with two cables feeding
More information