IS31AP4991 CLASS-AB AUDIO AMPLIFIER
|
|
- George Montgomery
- 6 years ago
- Views:
Transcription
1 IS3AP499 CLASS-AB AUDIO AMPLIFIER DESCRIPTION The IS3AP499 demo board is a fully assembled and tested PCB that uses the IS3AP499 Class-AB power amplifier to drive an 8Ω or larger speaker in portable audio applications. The demo board accepts a single-ended input signal. The demo board provides a BTL output capable of delivering.w into an 8Ω speaker at 5V. FEATURES Supply voltage range from.7v to 5.5V Delivers.W into an 8Ω speaker at 5V supply. (THD+N=%). Ultra-low distortion (.5%@.5W, khz) Available in MSOP-8 and SOP-8 package QUICK START RECOMMENDED EQUIPMENT 5.V, A power supply Audio source (i.e. MP3 player, Notebook PC, etc.) 8Ω speaker ABSOLUTE MAXIMUM RATINGS 5.5V power supply Caution: Do not exceed the conditions listed above; otherwise the board will be damaged. PROCEDURE The IS3AP499 demo board is fully assembled and tested. Follow the steps listed below to verify board operation. Caution: Do not turn on the power supply until all connections are completed. ) Connect an 8Ω (or larger) speaker across the OUT- terminal and OUT+ terminal. Or connect speaker to the connector (AUDIO OUT). ) Connect the ground terminal of the power supply to the GND and the positive terminal to the. Or connect DC power to connector (DC INPUT). 3) Connect the audio source to the IN- terminal; or connect audio source to the connector (AUDIO INPUT). 4) Turn on the power supply. 5) Turn on the audio source. Figure : Photo of IS3AP499 Evaluation Board Note: Only one IC type will be installed on PCB. ORDERING INFORMATION Part No. Temperature Range Package IS3AP499-GRLS-EB IS3AP499-SLS-EB -4 C ~ +85 C (Industrial) Table : Ordering Information SOP-8, Lead-free MSOP-8, Lead-free For pricing, delivery, and ordering information, please contacts ISSI s analog marketing team at analog@issi.com or (48) Integrated Silicon Solution, Inc. Rev. A, /7/5
2 IS3AP499 CLASS-AB AUDIO AMPLIFIER DETAILED DESCRIPTION The IS3AP499 demo board features the IS3AP499 Class-AB power amplifier IC, designed to drive speaker impedance of 8Ω or larger. CUSTOMIZING THE GAIN The IS3AP499 demo board is shipped with a gain of 8.3dB and is set by resistors R I (R ) and R F (R ). Change resistors R I and R F to reconfigure the gain of the board and gain determined in Equation () RF V G ain () R I V HIGH-PASS FILTER The input capacitor C I (C 4 ) and input resistor R I (R ) form a high-pass filter with the corner frequency, f C, determined in Equation () and refer to IS3AP499 data sheet for more detail. f c SHUTDOWN MODE R C () I I Jumper (JP) controls the shutdown pin of the IS3AP499 IC. Connect the shunt across pin and of the jumper (JP) to enter the shutdown mode of the board. DC INPUT C uf C uf C5 NC R 8k C3.uF U 6 Audio IN C4 5nF R k C6 uf 4 3 Vin- Standby Vin+ Bypass GND 7 Vout 5 Vout 8 IS3AP499_MSOP8 SPEAKER R3 k C7 U 8.uF 3 Vin- Vout JP CLOSE=SD 7 5 Standby Vin+ Bypass GND Vout 6 4 IS3AP499_SOP8 Figure : IS3AP499 Application Circuit Integrated Silicon Solution, Inc. Rev. A, /7/5
3 IS3AP499 CLASS-AB AUDIO AMPLIFIER BILL OF MATERIALS Name Symbol Description Qty Supplier Part No. Amplifier U Class- AB power amplifier ISSI IS3AP499 Resistor R RES,k,/6W,±%,SMD Yageo RC63FR-7KL Resistor R RES,8k,/6W,±%,SMD Yageo RC63FR-78KL Resistor R3 RES,k,/6W,±5%,SMD Yageo RC63JR-7KL Capacitor C CAP,µF,V,±%,SMD Yageo CC85KKX7R6BB6 Capacitor C,C6 CAP, µf,5v,±%,smd Yageo CC63KKX7R9BB5 Capacitor C3,C7 CAP,.µF,5V,±%,SMD Yageo CC63KKX7R9BB4 Capacitor C4 CAP,5nF,5V,±%,SMD Yageo CC63KKX7R9BB53 Connector DC INPUT.5mm DC connector Connector AUDIO OUT RCA type connector Connector AUDIO INPUT 3.5mm min connector U,C5 No installed Bill of materials, refers to Figure above. Integrated Silicon Solution, Inc. 3 Rev. A, /7/5
4 IS3AP499 CLASS-AB AUDIO AMPLIFIER Figure : Board Component Placement Guide - Top Layer Figure 3: Board PCB Layout - Top Layer Integrated Silicon Solution, Inc. 4 Rev. A, /7/5
5 IS3AP499 CLASS-AB AUDIO AMPLIFIER Figure 4: Board Component Placement Guide - Bottom Layer Figure 5: Board PCB Layout - Bottom Layer Copyright 5 Integrated Silicon Solution, Inc. All rights reserved. ISSI reserves the right to make changes to this specification and its products at any time without notice. ISSI assumes no liability arising out of the application or use of any information, products or services described herein. Customers are advised to obtain the latest version of this device specification before relying on any published information and before placing orders for products. Integrated Silicon Solution, Inc. does not recommend the use of any of its products in life support applications where the failure or malfunction of the product can reasonably be expected to cause failure of the life support system or to significantly affect its safety or effectiveness. Products are not authorized for use in such applications unless Integrated Silicon Solution, Inc. receives written assurance to its satisfaction, that: a.) the risk of injury or damage has been minimized; b.) the user assume all such risks; and c.) potential liability of Integrated Silicon Solution, Inc is adequately protected under the circumstances Integrated Silicon Solution, Inc. 5 Rev. A, /7/5
IS31AP4066D CLASS-AB AUDIO AMPLIFIER
ISAP466D CLASS-AB AUDIO AMPLIFIER DESCRIPTION The ISAP466D demo board is a fully assembled and tested PCB that uses the ISAP466D Class-AB dual bridge-connected audio power amplifier. Designed to drive
More informationFor pricing, delivery, and ordering information, please contact ISSI at or call
IS3AP488D Class-AB Audio Amplifier Evaluation Board Guide Description The IS3AP488D demo board is a fully assembled and tested PCB that uses the IS3AP488D Class-AB a dual bridge-connected audio power amplifier.
More informationIS31AP2145E MONO CLIP-LESS & FILTER-LESS CLASS-D AUDIO POWER AMPLIFIER
IS3AP45E.7W@5V MONO CLIP-LESS & FILTER-LESS CLASS-D DESCRIPTION The IS3AP45E is a.7w@5.v mono, clip-less, filter-less, high efficiency Class-D audio power amplifier with automatic gain control. The IS3AP45E
More informationIS31SE CH CAPACITIVE TOUCH SENSOR EVALUATION BOARD GUIDE
ISSE0 -CH CAPACITIVE TOUCH SENSOR EVALUATION BOARD GUIDE DESCRIPTION The ISSE0 is an ultra low power, fully integrated solution for capacitive touch applications with up to surfaces. The chip allows electrodes
More informationIS31AP2145A Class-D Audio Amplifier Evaluation Board Guide
Description The IS31AP2145A demo board is a fully assembled and tested PCB that uses the IS31AP2145A Class-D audio amplifier to drive speakers with 4Ω load or larger. The device is designed for battery
More informationProcedure. Part No. Temperature Range Package IS31BL3231-DLS2-EB -40 C to +85 C (Industrial) DFN-10 (3mm x 3mm), Lead-free
ISBL Flash LED Driver Evaluation Board Guide Description ISBL flash LED driver demo board is used to demonstrate and evaluate the ISBL. The ISBL is a current-regulated charge pump and ideal for powering
More informationIS31LT3918 T8 Lighting Evaluation Board Guide
Description Quick Start The IS31LT3918 LED driver IC is a peak current detection buck converter which operates in constant off time mode. It operates over a very wide input voltage supply range of 6VDC
More informationIS31LT3938 Bulb Lighting DEMO Board Guide
Description IS31LT3938 LED driver IC is a peak current detection buck converter which operates in constant off time mode. It operates over a very wide input voltage supply range of 10VDC to 450VDC or 110VAC/220VAC.
More informationIS31LT3935 Bulb Lighting Evaluation Board Guide. Description. Features. Applications. Quick Start. Ordering Information. or call
Description The Flicker-Free TM IS31LT3935 is a single stage current mode LED driver optimized for high power factor and compatibility with all TRIAC dimmers. The PFC architecture enables excellent power
More informationIS31LT3916 Isolation Bulb Lighting DEMO Board Guide
Description The IS31LT3916 is a primary side, peak current mode, isolated or non-isolated type HBLED driver. The device works at a constant frequency in discontinuous conduction mode to provide a constant
More informationAN2474 Application note
AN474 Application note TS4995.W fully differential audio power amplifier with selectable standby and 6db fixed gain - Evaluation board user guidelines Introduction This application note describes the DEMO
More informationIS31LT3916 Non-Isolation T8 Lighting DEMO Board Guide
Description The IS31LT3916 is a primary side, peak current mode, isolated or non-isolated type HBLED driver. The device works at a constant frequency in discontinuous conduction mode to provide a constant
More informationMAX14535E Evaluation Kit. Evaluates: MAX14535E
19-4510; Rev 0; 3/09 General Description The MAX14535E evaluation kit (EV kit) demonstrates the MAX14535E double-pole/double-throw (DPDT) analog switch featuring negative signal capability, low onresistance
More informationFigure 1 Typical Application Circuit
4-CH CAPACITIVE TOUCH SENSOR WITH AUTO CALIBRATION August 2015 GENERAL DESCRIPTION The IS31SE5104 is a low power, fully integrated 4-channel solution for capacitive touch button applications. The chip
More informationIS31BL3231. FLASH LED DRIVER July 2015
FLASH LED DRIVER July 2015 GENERAL DESCRIPTION The IS31BL3231 is a current-regulated charge pump and ideal for powering high brightness LEDs for camera flash and torch applications. The charge pump can
More informationIS31LT3916 Isolation T8 Lighting DEMO Board Guide
Description The IS31LT3916 is a primary side, peak current mode, isolated or non-isolated type HBLED driver. The device works at a constant frequency in discontinuous conduction mode to provide a constant
More information2.7 W x 4 CS35L00 Amplifier Demonstration Board
CDB35L00-X4 2.7 W x 4 CS35L00 Amplifier Demonstration Board Features Description Contains 4 CS35L00 Hybrid Class-D Amplifiers Selectable +6 db or +12 db Gain Selectable Operational Modes Device Shutdown
More information1 x 1.7 W CS35L01 Amplifier Reference Design Kit
1 x 1.7 W CS35L01 Amplifier Reference Design Kit Features Description Four boards provided in the CS35L01 Amplifier Reference Design Kit Separate boards for each mode configuration SD, FSD, HD, and FHD
More informationA WATT FULLY DIFFERENTIAL AUDIO POWER AMP W/INTERNAL FEEDBACK RESISTORS DETECTOR. Application. Ordering Information
Description The is a fully differential audio power amplifier designed for portable communication device applications. It is capable of delivering 1.25 watt of continuous average power to an 8Ω BTL load
More informationEvaluate: MAX14589E/MAX14594E/ MAX MAX14589E/MAX14594E/ MAX14689 Evaluation Kits. Features and Benefits. General Description.
Evaluation Kits General Description The MAX14589E/MAX14594E/ evaluation kits (EV kits) are fully assembled and tested circuit boards that demonstrate the functionality of the MAX14589E, MAX14594E, and
More informationEV2617-L-00A. 3A, 1-Cell Li-Ion Battery Switching Charger With NVDC Power Path Management FEATURES DESCRIPTION APPLICATIONS ELECTRICAL SPECIFICATION
EV2617-L-00A 3A, 1-Cell Li-Ion Battery Switching Charger With NVDC Power Path Management The Future of Analog IC Technology DESCRIPTION The EV2617-L-00A is an evaluation board for MP2617, a 3A/1.6MHz 1-cell
More informationHigh Current Power Switch
SP619 High Current Power Switch FEATURES Max RDS(ON).377 Ohms Overcurrent deactivation 800mA Max leakage current less than 2µA while deactivated Small 6 pin SOT-23 package Built-in Over-temperature Protection
More informationVBattery 7 VCC V DD IRLED IS31SE5001 SDA SCL INTB SDB. Figure 1 Typical Application Circuit
IR SENSOR FOR TOUCHLESS PROXIMITY July 2013 GENERAL DESCRIPTION The IS31SE5001 is a low-power, reflectance-based infrared light sensor with advanced signal processing and digital output. The sensor can
More informationTPA4861 Audio Power Amplifier Evaluation Module DATA MANUAL: SLOU004
TPA4861 Audio Power Amplifier Evaluation Module DATA MANUAL: SLOU004 Date: July 1997 IMPORTANT NOTICE Texas Instruments and its subsidiaries (TI) reserve the right to make changes to their products or
More informationXR32220 Evaluation Board User s Manual
XR32220 Evaluation Board User s Manual Introduction Exar s XR32220 EVB evaluation board provides a platform on which to examine the features and performance of the XR32220 2-Driver/2-Receiver RS-232 serial
More informationAN BGA301x Wideband Variable Gain Amplifier Application. Document information. Keywords
Rev. 2 3 February 2014 Application note Document information Info Content Keywords BGA3015, BGA3018, BAP70Q, CATV, Line-up, VGA, Evaluation board Abstract This application note describes the schematic
More informationUM User manual for the BGU MHz LNA evaluation board. Document information
User manual for the BGU7003 868MHz LNA evaluation board Rev.1.0 06 December 2011 User manual Document information Info Content Keywords 868MHz LNA, BGU7003. Application Board ordering info: Abstract This
More informationXR-2206/2211/2212. Evaluation System User Manual
...the analog plus company TM XR-2206--2ES November 996-4 XR-2206/22/222 Evaluation System User Manual Rev..00 996 EXAR Corporation, 48720 Kato Road, Fremont, CA 94538 (50) 668-7000 FAX (50) 668-707 XR-2206--2ES
More informationMIC5281. Features. General Description. Applications. Typical Application. 120V IN, 25mA, Ultra-Low IQ, High-PSRR Linear Regulator
120V IN, 25mA, Ultra-Low IQ, High-PSRR Linear Regulator General Description The high-performance linear regulator offers a very-wide input operating voltage range, up to 120V DC, and supplies an output
More informationMAX3804 Evaluation Kit. Evaluates: MAX3804. Features DC-Coupled EV Kit SMA Connectors for All High-Speed Inputs and Outputs Fully Assembled and Tested
19-2821; Rev 1; 2/09 General Description The MAX3804 DC-coupled evaluation kit (EV kit) simplifies evaluation of the MAX3804 12.5Gbps settable equalizer. The EV kit enables full testing of the device functions
More informationAN2240 Application note
AN0 Application note Using the evaluation board for the TS7 low noise microphone preamplifier with V bias Introduction This application note describes the DEMO TS7 evaluation board, specifically designed
More informationEvaluates: MAX40009/MAX MAX40009 Evaluation Kit. Quick Start. General Description. Procedure. Features. Required Equipment
General Description The MAX40009 evaluation kit (EV kit) is a fully assembled and tested PC board that evaluates the MAX40008/ MAX40009 single comparator with shutdown input. This EV kit comes with a push-pull
More information+Denotes lead-free and RoHS-compliant
19-0997; Rev 0; 9/07 MAX4208 Evaluation Kit General Description The MAX4208 evaluation kit (EV kit) simplifies evaluation of the MAX4208 ultra-low offset/drift, adjustable gain, precision instrumentation
More informationEvaluates: MAX98357A/MAX98357B (TQFN) MAX98357 Evaluation System (TQFN)
General Description The MAX98357 development board (DEV board) is a fully assembled and tested PCB that evaluates the MAX98357 I2S digital input Class D power amplifier. The DEV board operates from a single
More informationPAM8304-EV board User Guide AE Department. Date Revision Description Comment
1. Revision Information -EV board User Guide AE Department Date Revision Description Comment 2013/5/31 V1.0 Initial release 1 of 5 2. Key Features Supply Voltage from 2.8V to 6.0V 3.0W@10% THD Output with
More informationAN2470 Application note TS4871 low voltage audio power amplifier Evaluation board user guidelines Features Description
Application note TS4871 low voltage audio power amplifier Evaluation board user guidelines Features TS4871 low voltage audio power amplifier with active low standby mode Operating range from V CC =2.2V
More informationNovember 2000 Mixed-Signal Products SLOU086
User s Guide November 2000 Mixed-Signal Products SLOU086 IMPORTANT NOTICE Texas Instruments and its subsidiaries (TI) reserve the right to make changes to their products or to discontinue any product or
More informationQUICK START GUIDE FOR DEMONSTRATION CIRCUIT 995A ADJUSTABLE LDO LINEAR REGULATOR LT3080EDD DESCRIPTION
LT3080EDD DESCRIPTION Demonstration circuit 995A is an adjustable 1.1A linear regulator featuring LT 3080. Architected as a precision current source and voltage follower, it allows this new regulator to
More information+Denotes lead-free and RoHS-compliant.
19-0993; Rev 0; 9/07 MAX4209 Evaluation Kit General Description The MAX4209 evaluation kit (EV kit) simplifies evaluation of the MAX4208 ultra-low offset/drift, fixed gain, precision instrumentation amplifier
More informationGeneral Description. Features. Component List. Component Suppliers
General Description The MAX5911 evaluation kit (EV kit) is a fully assembled and tested surface-mount circuit board that demonstrates the MAX5911 fully integrated hot-swap solution for negative supply
More information73M1866B Keychain Demo Board User Manual
Simplifying System Integration TM 73M1866B Keychain Demo Board User Manual November 17, 2008 Rev. 1.0 73M1866B Keychain Demo Board User Manual 2008 Teridian Semiconductor Corporation. All rights reserved.
More informationRT9055-NGWSC Evaluation Board
300mA Dual LDO Regulator Purpose The RT9055 is a dual channel, low noise, and low drop Regulator sourcing up to 300mA at each channel. Its input voltage range is from 1.5V to 5.5V and provides an adjustable
More information2001 Mixed-Signal Products SLOU091A
User s Guide 2001 Mixed-Signal Products SLOU091A Preface How to Use This Manual This document contains the following chapters: Chapter 1 Introduction Chapter 2 Operation Related Documentation From Texas
More informationA mA CMOS LOW NOISE LOW-DROPOUT VOLTAGE REGULATOR. Application. Pin Description
Description The series of fixed output low dropout linear regulators are designed for portable battery powered applications which require low noise operation, fast enable response time, and low dropout.
More information+Denotes lead-free and RoHS compliant.
19-2446; Rev 1; 6/08 MAX17062 Evaluation Kit General Description The MAX17062 evaluation kit (EV kit) is a fully assembled and tested surface-mount PCB that provides the voltages required for active-matrix,
More informationA6150 LOW DROPOUT VOLTAGE REGULATOR 150mA CMOS LOW NOISE
DESCRIPTION The series of fixed output low dropout linear regulators are designed for portable battery powered applications which require low noise operation, fast enable response time, and low dropout.
More informationMIC5282. General Description. Features. Applications. Typical Applications. 120V IN, 50mA, Ultra-Low I Q, High-PSRR Linear Regulator
12V IN, 5mA, Ultra-Low I Q, High-PSRR Linear Regulator General Description The high-performance linear regulator offers a very-wide input operating voltage range, up to 12V DC, and supplies an output current
More informationXR76117/21. PowerBlox 15A and 20A Synchronous Step Down COT Regulator GENERAL DESCRIPTION EVALUATION BOARD MANUAL FEATURES
XR76117/21 November 2016 GENERAL DESCRIPTION The XR76117 and XR76121 are synchronous step-down regulators combining the controller, drivers, bootstrap diode and MOSFETs in a single package for point-of-load
More informationEvaluation Board for CS4351
Features Demonstrates recommended layout and grounding arrangements. CS8416 receives S/PDIF, & EIAJ-340- compatible digital audio. Evaluation Board for CS4351 Headers for External PCM Audio and Control
More informationReversible motor driver
Reversible motor driver The BA6289F and BA6417F are reversible-motor drivers, with an output current of 600mA for the former and 1A for the latter. Two logic inputs allow four output modes: forward, reverse,
More informationMAX3160E Evaluation Kit. Evaluates: MAX3160E. Features
9-076; Rev 0; 4/07 MAX60E Evaluation Kit General Description The MAX60E evaluation kit (EV kit) circuit demonstrates the RS-/RS-485/RS-4 multiprotocol transceivers using the MAX60E IC. The circuit can
More informationXRD87L85 Low-Voltage CMOS 8-Bit High-Speed Analog-to-Digital Converter
Low-Voltage CMOS 8-Bit High-Speed Analog-to-Digital Converter April 2002-1 FEATURES 8-Bit Resolution Up to 10 MHz Sampling Rate Internal S/H Function Single Supply: 3.3V VIN DC Range: 0V to V DD VREF DC
More informationEVAL-INAMP-62RZ/82RZ/82RMZ
Evaluation Boards for the AD620 Series and and the AD8220 Series Instrumentation Amplifiers EVAL-INAMP-62RZ/82RZ/82RMZ FEATURES 3 generic, easy-to-use PC boards Support several related in-amp products
More informationAN BGA GHz 18 db gain wideband amplifier MMIC. Document information. Keywords. BGA3018, Evaluation board, CATV, Drop amplifier.
Rev. 2 8 January 2013 Application note Document information Info Keywords Abstract Content BGA3018, Evaluation board, CATV, Drop amplifier This application note describes the schematic and layout requirements
More informationMAX3161E Evaluation Kit. Evaluates: MAX3161E. Features
19-0803; Rev 0; 4/07 MX3161E Evaluation Kit General Description The MX3161E evaluation kit (EV kit) circuit demonstrates the RS-232/RS-485/RS-422 multiprotocol transceivers using the MX3161E IC. The circuit
More informationZLED7030KIT-D1 Demo Kit Description
ZLED7030KIT-D Demo Kit Description Kit Important Notice Restrictions in Use IDT s ZLED7030KIT-D Demo Kit hardware is designed for ZLED7030 demonstration, evaluation, laboratory setup, and module development
More informationMIC24051 Evaluation Board
6A, High-Efficiency, Synchronous DC/DC Buck Regulator with Hyper Speed Control SuperSwitcher II General Description The MIC2451 DC/DC synchronous buck regulator operates over an input supply range of 4.5V
More informationNCN1154MUTGEVB. NCN1154 DP3T USB 2.0 High Speed Audio Switch Evaluation Board User's Manual EVAL BOARD USER S MANUAL
NCN54 DP3T USB.0 High Speed Audio Switch Evaluation Board User's Manual Prepared by: Bertrand RENAUD On Semiconductor EVAL BOARD USER S MANUAL OVERVIEW The NCN54 is a DP3T switch for combined true ground
More informationS Low-Power Shutdown Input S Fully Assembled and Tested. Maxim Integrated Products 1
19-5599; Rev 0; 10/10 MAX98303 Evaluation Kit General Description The MAX98303 evaluation kit (EV kit) is a fully assembled and tested PCB that evaluates the MAX98303 stereo 3.1W Class D amplifier in a
More informationTPA1517DWP Audio Power Amplifier Evaluation Module DATA MANUAL: SLOU008
TPA1517DWP Audio Power Amplifier Evaluation Module DATA MANUAL: SLOU008 Date: July 1997 IMPORTANT NOTICE Texas Instruments and its subsidiaries (TI) reserve the right to make changes to their products
More informationDEMO MANUAL DC2072A LT V, 500mA Low Noise Linear Regulator with Programmable Current Limit and Power Good
Description DEMO MANUAL DC2072A LT3065 45, 500mA Low Noise Linear Regulator with Programmable Current Limit and Power Good Demonstration circuit 2072A is an adjustable 500mA linear regulator featuring
More informationLM48555 Evaluation Board
LM48555 Evaluation Board Quick Start Guide 1) Apply power supply voltage to positive terminal of JU4, and source ground to the negative terminal. 2) Short the terminals of JU1 to release the device from
More informationMAX5097A Evaluation Kit. Evaluates: MAX5097A
19-0718; Rev 0; 1/07 MAX5097A Evaluation Kit General Description The MAX5097A evaluation kit (EV kit) demonstrates the MAX5097A in a standard application circuit demonstrating high efficiency. The EV kit
More informationMIC2544A/2548A. General Description. Features. Applications. Typical Application. Programmable Current Limit High-Side Switch
Programmable Current Limit High-Side Switch General Description The MIC2544A and MIC2548A are integrated, high-side power switches optimized for low loss DC power switching and other power management applications,
More information+Denotes lead(pb)-free and RoHS compliant. FOUTL-, FOUTL+, FOU TR-, FO U TR+, V D D, P G N D
19-4071; Rev 1; 9/09 MAX9736A Evaluation Kit General Description The MAX9736A evaluation kit (EV kit) is a fully assembled and tested printed-circuit board (PCB) that configures the MAX9736A Class D amplifier
More informationXR21V1410 EVALUATION BOARD USER S MANUAL 1.0 INTRODUCTION
1.0 INTRODUCTION This user s manual is for the XR21V1410 evaluation board. It will describe the hardware setup required to operate the part. 2.0 OVERVIEW The XR21V1410 evaluation board has one 16-QFN package
More informationDecember 2009 Rev FEATURES. C2 0.47uF. C1 0.47uF C2P C1P C2N 17. COUT 10uF VOUT U1 U1 XRP6840 CAP 14. C3 CAPxx GND 13 NC 12 PGND FLASH LED3
December 2009 Rev. 1.0.0 GENERAL DESCRIPTION The XRP6840 is a controlled-current dual-cell supercapacitor charger and high power LED driver. Operating from a standard lithium-ion battery, the XRP6840 provides
More informationSiGe:C LOW NOISE AMPLIFIER FOR GPS
DESCRIPTION BIPOLAR ANALOG INTEGRATED CIRCUIT PC8230TU SiGe:C LOW NOISE AMPLIFIER FOR GPS The PC8230TU is a silicon germanium carbon (SiGe:C) monolithic integrated circuit designed as low noise amplifier
More informationMAX3983 SMA Connector Evaluation Kit
19-3340; Rev 0, 7/04 MAX3983 SMA Connector Evaluation Kit General Description The MAX3983 SMA Connector evaluation kit (EV Kit) is an assembled demonstration board that provides electrical evaluation of
More informationMaxim Integrated Products 1
19-3093; Rev 0; 12/03 MAX3942 Evaluation Kit General Description The MAX3942 evaluation kit (EV kit) is an assembled demonstration board that provides electrical evaluation of the MAX3942 10.7Gbps modulator
More informationSpecifications are at T A = 25 C
DESCRIPTION The demo circuit 1559A features the LTM8046, a 2kVAC, 2.5W isolated flyback μmodule converter. The demo circuit is designed for a 5V output from a 3.2V to 26V input. The typical current capability
More informationFEATURES DESCRIPTION APPLICATIONS BLOCK DIAGRAM. PT W Stereo Integrated Audio Amplifier
0W Stereo Integrated Audio Amplifier DESCRIPTION The PT830 is an integrated audio amplifier design for the compact audio system; the maximum output power is up to 0W x. Utilizing PTC exclusive, patented
More informationS Application Circuit with SATA Input/Output S Eye Diagram Test Circuit with SMA Inputs/ Outputs
19-4953; Rev 0; 9/09 MAX4951AE Evaluation Kit General Description The MAX4951AE evaluation kit (EV kit) provides a proven design to evaluate the MAX4951AE dual-channel buffer. The EV kit contains four
More informationAOZ8882. Ultra-Low Capacitance TVS Diode Array. General Description. Features. Applications. Typical Application
Ultra-Low Capacitance TS Diode Array General Description The AOZ8882 is a transient voltage suppressor array designed to protect high speed data lines such as HDMI, MDDI, USB, SATA, and Gigabit Ethernet
More informationTABLE 1: PACKAGE LIST. XRA1402IL16-F 16-pin QFN U7. XRA1402IG16-F 16-pin TSSOP U6. XRA1404IL16-F 16-pin QFN U7. XRA1404IG16-F 16-pin TSSOP U6
REV. 1.0.0 INTRODUCTION XRA1402/1404 EVALUATION BOARD USER S MANUAL This user s manual is for the XRA1402/1404 8-bit evaluation board. Table 1 shows the different devices and packages that the evaluation
More information1 GHz wideband low-noise amplifier with bypass. The LNA is housed in a 6-pin SOT363 plastic SMD package.
Rev. 2 14 September 2010 Product data sheet 1. Product profile 1.1 General description The MMIC is a wideband amplifier with. It is designed specifically for high linearity, low-noise applications over
More informationTPA1517NE Audio Power Amplifier Evaluation Module DATA MANUAL: SLOU007
TPA1517NE Audio Power Amplifier Evaluation Module DATA MANUAL: SLOU007 Date: July 1997 IMPORTANT NOTICE Texas Instruments and its subsidiaries (TI) reserve the right to make changes to their products or
More informationRT6238AHGQUF Evaluation Board
8A, 18V, 500kHz, ACOT Synchronous Step-Down Converter Purpose The RT6238A is an ACOT control architecture step-down converter, which the input voltage range is from 4.5V to 18V and the output is adjustable
More informationAOZ8102. Ultra-Low Capacitance TVS Diode Array. Features. General Description. Applications. Typical Application
Ultra-Low Capacitance TS Diode Array General Description The is a transient voltage suppressor array designed to protect high speed data lines from SD and lightning. This device incorporates eight surge
More informationS U1 Configured for Filterless Output S U2 Configured for Filtered Output S Fully Assembled and Tested. Maxim Integrated Products 1
19-5505; Rev 0; 9/10 MAX98400B Evaluation Kit General Description The MAX98400B evaluation kit (EV kit) configures the MAX98400B Class D amplifier to drive 2x12W into a pair of 8I speakers in stereo mode
More informationEvaluates: MAX MAX44211 Evaluation Kit. Quick Start. General Description. Benefits and Features. Required Equipment.
General Description The MAX44211 evaluation kit (EV kit) provides a proven design to evaluate the MAX44211 high-current differential line driver for powerline communications (PLC). The line driver is an
More information3 V, SUPER MINIMOLD 900 MHz Si MMIC AMPLIFIER
3 V, SUPER MINIMOLD 9 MHz Si MMIC AMPLIFIER FEATURES HIGH DENSITY SURFACE MOUNTING: pin super minimold or SOT-33 package GAIN: : Gs = 1 db TYP : Gs = 19 db TYP NOISE FIGURE: : NF = 3.3 db TYP : NF =.8
More information+Denotes lead-free and RoHS-compliant.
9-4067; Rev 0; /08 MAX95 Evaluation Kit General Description The MAX95 evaluation kit (EV kit) is a fully assembled and tested printed-circuit board (PCB) that simplifies the evaluation of the MAX95 400Mbps,
More informationNovalithIC H-Bridge Demo Board
Demo Board Description V1.0, 2011-09-23 Automotive Power General Description Figure 1 Demo board (top view) 1 General Description The NovalithIC H-Bridge/Dual-Halfbridge Demo Board contains two NovalithICs
More informationVCC -0.3 ~ 7 V. Maximum input voltage CP, CN, SHD, VOUT -0.3 ~ 7 V Power dissipation Pd 675 (*1) mw Operating temperature range
1/4 Structure Function Product Silicon Monolithic Integrated Circuit Voltage Regulated Charge Pump IC BU90030G Function - Input voltage range 2.0V~4.0V - PFM operation - Output voltage 4.0V (typ) - 1.5MHz(typ)
More informationTLT807B0EPV Demoboard
Preface Scope and purpose This application note provides information about the usage of the TLT807B0 Demoboard. The TLT807B0 Demoboard is used to demonstrate the ultra low quiescent current linear voltage
More informationEvaluation Board for CS3308. Description CS Channel. Digitally Controlled Analog Volume Control. PC or External Serial Control Input
Evaluation Board for CS3308 Features Description Single-ended Analog Inputs Single-ended Analog Outputs Supports AC and DC-Coupled Analog I/O Flexible Serial Control I/O Headers Serial Control Input Header
More informationSingle Phase Synchronous Buck Converter using ip1001 Overview
REFERENCE DESIGN IRDCiP11-B, 2kHz to 3kHz, 2A, 5V IN to 12V IN Single Phase Synchronous Buck Converter using ip11 Overview In this document, Table 1 and Figure 1 are provided to enable engineers to easily
More informationOctober 2002 PMP Portable Power SLVU074
User s Guide October 2002 PMP Portable Power SLVU074 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,
More informationDEMO MANUAL DC1520A LT3690: 36V/4A µpower Synchronous Buck Regulator DESCRIPTION PERFORMANCE SUMMARY
DESCRIPTION Demonstration circuit 1520A is a 36V, 4A synchronous Buck Regulator with 70μA Quiescent Current featuring the LT3690. The demo board is designed for 3.3V output from a 4.5V to 36V input with
More informationMAX9768 Evaluation Kit/Evaluation System
9-; Rev 0; /07 MAX9768 Evaluation Kit/Evaluation System General Description The MAX9768 evaluation kit (EV kit) is a fully assembled and tested printed-circuit board (PCB) that demonstrates the capabilities
More informationMAX17116Q Evaluation Kit Evaluates: MAX17116 in a 24-Pin TQFN Package
19-5846; Rev 0; 5/11 MAX17116Q Evaluation Kit General Description The MAX17116Q evaluation kit (EV kit) is a fully assembled and tested surface-mount PCB that evaluates the MAX17116 dual-output DC/DC power
More informationXRD8775 CMOS 8-Bit High Speed Analog-to-Digital Converter
CMOS 8-Bit High Speed Analog-to-Digital Converter April 2002-4 FEATURES 8-Bit Resolution Up to 20MHz Sampling Rate Internal S/H Function Single Supply: 5V V IN DC Range: 0V to V DD V REF DC Range: 1V to
More informationEvaluates: MAX MAX14970 Evaluation Kit. General Description. Quick Start (Application Circuit) Features. Table 1. Default Shunt Positions
General Description The MAX14970 evaluation kit (EV kit) provides a proven design to evaluate the MAX14970 dual-channel buffer. The EV kit contains four sections: an application circuit, characterization
More information+Denotes lead-free and RoHS-compliant.
19-3107; Rev 0; 12/07 MAX1493 Evaluation Kit General Description The MAX1493 is a low-power, 4.5-digit analog-to-digital converter (ADC) with integrated liquid-crystal display (LCD) drivers. The MAX1493
More information3.3V VIO_REF VCC XR21B1411 USBD- LOWPOWER J GND J10
REV..0.0 XRB_SP EVALUATION BOARD USER S MANUAL.0 INTRODUCTION This user s manual is for the XRB_SP evaluation board rev.. The XRB will be configured for the RS- mode when it is shipped from the factory.
More informationMAX11205PMB1 Peripheral Module
9-60; Rev 0; / MAX0PMB Peripheral Module General Description The MAX0PMB peripheral module provides the necessary hardware to interface the MAX0 6-bit ADC to any system that utilizes PmodK-compatible expansion
More informationEvaluation board Manual
Evaluation board Manual 7W no-isolation Blub AC220V MB39C602-EVB-CN02 Rev 1.0 Mar. 2013 1. Summarize The driver MB39C602-EVB-CN02 has the driving capability of 7 watts. It can be placed in some LED bulb,
More informationS Complete 2:1 VGA Multiplexer S VGA Connections and Power S LED Indicators for Switch Connections S VGA Inputs/Outputs S Fully Assembled and Tested
19-5030; Rev 0; 10/09 MAX4885AE Evaluation Kit General Description The MAX4885AE evaluation kit (EV kit) is a fully assembled and tested circuit board that evaluates the MAX4885AE VGA 2:1 multiplexer.
More informationS USB-PC Connection (Cable Not Included) S USB Powered (No External Power Supply Required) S Real-Time Data Acquisition Through the USB
19-5610; Rev 1; 8/11 MAXADClite Evaluation Kit General Description The MAXADClite evaluation kit (EV kit) evaluates the MAX11645, Maxim's smallest, very-low-power, 12-bit, 2-channel analog-to-digital converter
More information