XR21V1410 EVALUATION BOARD USER S MANUAL 1.0 INTRODUCTION
|
|
|
- Rodger Strickland
- 6 years ago
- Views:
Transcription
1 1.0 INTRODUCTION This user s manual is for the XR21V1410 evaluation board. It will describe the hardware setup required to operate the part. 2.0 OVERVIEW The XR21V1410 evaluation board has one 16-QFN package on it. Figure 1 shows a top view of XR21V1410 evaluation board layout. FIGURE 1. TOP VIEW OF XR21V1410 EVALUATION BOARD LAYOUT 1
2 REV Figure 2 shows a bottom view of XR21V1410 evaluation board layout. FIGURE 2. BOTTOM VIEW OF XR21V1410 EVALUATION BOARD LAYOUT 2.1 Evaluation Board Components On the XR21V1410 evaluation board, some componets are required to install. Some are optional and some are not installed. Table 1 shows the components: TABLE 1: COMPONENTS OF THE XR21V1410 EVALUATION BOARD UNIT LOCATION PART FUNCTION U1 Top SP6669AEK-L/TRR3 Exar s Voltage converter to step down voltage from 5V to 3.3V. U2 U3 Bottom SN74LVC2G53DCTR Multiplexer to switch between RS-232 and RS-485 mode. U4 Top XR21V1410IL16-F Exar s USB 1 channel UART. U5 Bottom NC7SZ14M5X Invert LowPower (suspend) signal. U6 Top AT24C02B I2C EEPROM. U7 Top SP3245EEY-L Exar s RS-232 transceiver. U8 Bottom SN74LVC2G66DCT Analog switch. U9 Top SP3497EEN-L Exar s RS-485 transceiver. CON1 Top PJ-002A External power input. 2
3 TABLE 1: COMPONENTS OF THE XR21V1410 EVALUATION BOARD UNIT LOCATION PART FUNCTION CON2 Top USB B-Type connector. Communication with USB host (USBD+, USBD-) and power source for evaluation board (V Bus ). CON3 Top R161 RS-232 mode DB9 male connector. CON4 Top ED555/4DS RS-485 mode 4X1 terminal block. NOTES:1) An external pull-up is required on the LOWPOWER pin for proper functionality. The external pull-up is not shown in the evaluation board schematics, but has been added on the evaluation board. 2) An external pull-up is required on any GPIO pins that is used as an input. In the suspend mode, the internal pull-up resistor is disabled and the input will be floating if there is no external pull-up resistor. The external pull-ups have not been added to the GPIOs used as inputs on this evaluation board. 2.2 Jumper Settings Common jumpers Common jumpers are those jumpers which should be set the same for both RS-232 and RS-485 mode. The Table 2 shows the common jumpers setting on the evaluation board: TABLE 2: COMMON JUMPERS SETTINGS JP1 Top Power select Jumper in 1&2 selects power from external power supply of 5V Jumper in 2&3 selects power from USB V BUS power JP2 Top Selects RS-232 or RS-485 mode Jumper in 1&2 selects RS-485 mode Jumper in 2&3 selects RS-232 mode (default) JP3 Top External loopback or test header Jumper in 1&2 selects external loopback JP4 Top SCL pull-up/pull-down select Jumper in 1&2 selects pull-up resistor Jumper in 2&3 selects pull-down resistor JP5 Top SDA pull-up/pull-down select Jumper in 1&2 selects pull-up resistor Jumper in 2&3 selects pull-down resistor JP6 Top Power supply for XR21V1410 Not installed. Trace between pin 1 & 2 JP7 Top I2C EEPROM header Jumper in 1&2 connects SCL to I2C EEPROM Jumper in 3&4 connects SDA to I2C EEROM NOTE: I2C EEPROM has not been programmed 3
4 REV Remote wakeup and jumper The SDA and SCL are used to specify whether Remote Wakeup and/or Bus Powered configurations are to be supported. These pins are sampled at power-up. The following Table 3 describes how Remote Wakeup and Bus Powered support. TABLE 3: REMOTE WAKEUP AND POWER MODES SDA SCL REMOTE WAKE-UP SUPPORT POWER MODE COMMENTS 1 1 No Self-Powered Default, if no EEPROM is present 1 0 No Bus-Powered 0 1 Yes Self-Powered 0 0 Yes Bus-Powered The following Table 4 shows jumpers related to remote wakeup. TABLE 4: REMOTE WAKEUP JUMPERS SETTINGS JP8 Top Select remote control wakeup signal Jumper in 1&2 selects RS-232 (RI#) signal Jumper in 2&3 selects push-button SW1 Top Generate remote wakeup signal Push once to generate one remote wakeup signal RS-232 mode jumpers (Default setting is RS-232) The XR21V1410 evaluation board is set as RS-232 mode by default. The following Table 5 shows the jumper settings apply to the RS-232 mode: TABLE 5: JUMPER SETTINGS FOR RS-232 MODE JP9 Top Selects power Not installed. Trace between pin 1&2 4
5 2.2.4 RS-485 mode jumpers The following Table 6 jumper setting applies to the RS-485 mode: TABLE 6: JUMPER SETTINGS FOR RS-485 MODE JP10 Top Select RTS or DTR direction control for JP11 Top Select direction control for RX and or always for RX Jumper in 1&2 selects RTS based direction control for Jumper in 2&3 selects DTR based direction control for Jumper in 1&2 selects common direction control for RX and Jumper in 2&3 enables RX always JP12 Top Selects power for RS-485 transceiver Not installed. Trace between pin 1 & 2. JP13 JP14 Top Selects half duplex or full duplex mode. Jumper in 1&2 selects half duplex mode Jumper in 2&3 selects full duplex mode 3.0 DRIVERS AND SUPPORT For any questions about this evaluation board, software drivers or technical support, send an to uarttechsupport@exar.com. NOTICE EXAR Corporation reserves the right to make changes to the products contained in this publication in order to improve design, performance or reliability. EXAR Corporation assumes no responsibility for the use of any circuits described herein, conveys no license under any patent or other right, and makes no representation that the circuits are free of patent infringement. Charts and schedules contained here in are only for illustration purposes and may vary depending upon a user s specific application. While the information in this publication has been carefully checked; no responsibility, however, is assumed for inaccuracies. EXAR Corporation does not recommend the use of any of its products in life support applications where the failure or malfunction of the product can reasonably be expected to cause failure of the life support system or to significantly affect its safety or effectiveness. Products are not authorized for use in such applications unless EXAR Corporation receives, in writing, assurances to its satisfaction that: (a) the risk of injury or damage has been minimized; (b) the user assumes all such risks; (c) potential liability of EXAR Corporation is adequately protected under the circumstances. Copyright 2009 EXAR Corporation Datasheet July Send your UART technical inquiry with technical details to hotline: uarttechsupport@exar.com. Reproduction, in part or whole, without the prior written consent of EXAR Corporation is prohibited. 5
CLK+ CLK- Expansion Interface TX+ TX-
REV. 1.0.0 1.0 INTRODUCTION XR17V358/354 EVALUATION BOARD USER S MANUAL This user s manual is for the XR17V358/354 evaluation board. The XR17V358 and XR17V354 are available in the same package and are
3.3V VIO_REF VCC XR21B1411 USBD- LOWPOWER J GND J10
REV..0.0 XRB_SP EVALUATION BOARD USER S MANUAL.0 INTRODUCTION This user s manual is for the XRB_SP evaluation board rev.. The XRB will be configured for the RS- mode when it is shipped from the factory.
TABLE 1: PACKAGE LIST. XRA1402IL16-F 16-pin QFN U7. XRA1402IG16-F 16-pin TSSOP U6. XRA1404IL16-F 16-pin QFN U7. XRA1404IG16-F 16-pin TSSOP U6
REV. 1.0.0 INTRODUCTION XRA1402/1404 EVALUATION BOARD USER S MANUAL This user s manual is for the XRA1402/1404 8-bit evaluation board. Table 1 shows the different devices and packages that the evaluation
XR21B1411 USER S MANUAL
REV. 1.0.0 WEB CONFIGURATION TOOL USER S MANUAL 1 WEB CONFIGURATION TOOL USER S MANUAL REV. 1.0.0 TABLE OF CONTENTS 1.0 OVERVIEW... 3 2.0 GPIO PIN CONFIGURATIONS... 3 2.1 CONFIGURING THE GPIO PINS IN GPIO
For more information about EEPROM, please refer to our DAN 112 that could be found at our website
REV. 1.0.0 1.0 INTRODUCTION XR16M654 & XR16M554 EVALUATION BOARD USER S MANUAL This user s manual is for both the XR16M654 and the XR16M554 evaluation board. Since it can be used for both XR16M654 and
DATA COMMUNICATIONS APPLICATION NOTE DAN132
EXAR S SINGLE CHANNEL UARTS COMPARED WITH TI S TL16C550C June 2002 Author: PY 1.0 INTRODUCTION This application note describes the major difference between Exar s ST16C550, ST16C580, ST16C650A, and XR16C850
DATA COMMUNICATIONS APPLICATION NOTE DAN137
November 2003 EXAR XR16L580 COMPARED WITH TI S TL16C550C (48-TQFP) Author: BL & PY 1.0 INTRODUCTION This application note describes the major differences between Exar s XR16L580 and TI s TL16C550C (PT
DATA COMMUNICATIONS APPLICATION NOTE DAN133
EXAR S QUARTS COMPARED WITH TI S TL16C554 AND TL16C554A June 2002 Author: PY 1.0 INTRODUCTION This application note describes the major difference between Exar s QUARTs (ST16C554, ST16C654, and XR16C854)
GENERAL DESCRIPTION FEATURES
January 2010 Rev. 1.0.1 GENERAL DESCRIPTION The is designed to allow individuals to program the NVM (Non-Volatile Memory) in the XRP7704, XRP7708, XRP7740, and XRP7714. The board consists of a microcontroller
XR-2206/2211/2212. Evaluation System User Manual
...the analog plus company TM XR-2206--2ES November 996-4 XR-2206/22/222 Evaluation System User Manual Rev..00 996 EXAR Corporation, 48720 Kato Road, Fremont, CA 94538 (50) 668-7000 FAX (50) 668-707 XR-2206--2ES
XRA BIT I2C/SMBUS GPIO EXPANDER WITH INTEGRATED LEVEL SHIFTERS
SEPTEMBER 2011 REV. 1.0.0 GENERAL DESCRIPTION The XRA1207 is a 16-bit GPIO expander with an I 2 C/ SMBus interface. After power-up, the XRA1207 has internal 100K ohm pull-up resistors on each pin that
XRA1201/1201P 16-BIT I2C/SMBUS GPIO EXPANDER
SEPTEMBER 2011 REV. 1.0.0 GENERAL DESCRIPTION The XRA1201/1201P is a 16-bit GPIO expander with an I 2 C/SMBus interface. After power-up, the XRA1201 has internal 100K ohm pull-up resistors on each pin
+5V Powered Multi-Channel RS-232 Drivers/Receivers
SP238A 5V Powered Multi-Channel RS-232 Drivers/Receivers Operates from a Single 5V Power Supply Meets All RS-232D and V.28 Specifications ±30V Receiver Input Levels Low Power CMOS Operation Operates with
XRA1202/1202P 8-BIT I2C/SMBUS GPIO EXPANDER WITH RESET
8-BIT I2C/SMBUS GPIO EXPANDER WITH RESET APRIL 2013 REV. 1.0.1 GENERAL DESCRIPTION The XRA1202/1202P is an 8-bit GPIO expander with an I 2 C/SMBus interface. After power-up, the XRA1202 has internal 100K
January 2014 Rev FEATURES
January 2014 Rev. 1.1.0 GENERAL DESCRIPTION In some applications it would be more desirable to download a runtime image from a micro controller onto RAM than to store a configuration into flash memory.
DATA COMMUNICATIONS APPLICATION NOTE DAN170
AUGUST 2004 MIGRATING TO EXAR S FIFTH GENERATION UARTS: XR16L784/788 Author: BL 1.0 INTRODUCTION This application note provides sytem design engineers with the information necessary to migrate to Exar
December 2009 Rev FEATURES. C2 0.47uF. C1 0.47uF C2P C1P C2N 17. COUT 10uF VOUT U1 U1 XRP6840 CAP 14. C3 CAPxx GND 13 NC 12 PGND FLASH LED3
December 2009 Rev. 1.0.0 GENERAL DESCRIPTION The XRP6840 is a controlled-current dual-cell supercapacitor charger and high power LED driver. Operating from a standard lithium-ion battery, the XRP6840 provides
HX2VL Development Kit Guide. Doc. # Rev. *A
HX2VL Development Kit Guide Doc. # 001-73960 Rev. *A Cypress Semiconductor 198 Champion Court San Jose, CA 95134-1709 Phone (USA): 800.858.1810 Phone (Intnl): 408.943.2600 http://www.cypress.com Copyrights
XR76117/21. PowerBlox 15A and 20A Synchronous Step Down COT Regulator GENERAL DESCRIPTION EVALUATION BOARD MANUAL FEATURES
XR76117/21 November 2016 GENERAL DESCRIPTION The XR76117 and XR76121 are synchronous step-down regulators combining the controller, drivers, bootstrap diode and MOSFETs in a single package for point-of-load
XR32220 Evaluation Board User s Manual
XR32220 Evaluation Board User s Manual Introduction Exar s XR32220 EVB evaluation board provides a platform on which to examine the features and performance of the XR32220 2-Driver/2-Receiver RS-232 serial
AN10428 UART-SPI Gateway for Philips SPI slave bridges
UART-SPI Gateway for Philips SPI slave bridges Rev. 01 7 March 2006 Application note Document information Info Keywords Abstract Content UART-SPI Gateway, UART to SPI, RS-232 to SPI The UART-SPI Gateway
USB2I 2 C Programming Kit Quick-Start User s Guide
Revision A USB2I 2 C Programming Kit Quick-Start User s Guide General Description The SMX3203 USB programming system is used for device prototype development. The SMX3203 system consists of a programming
SP5301. Universal Serial Bus Transceiver
SP5301 Universal Serial Bus Transceiver Utilizes digital inputs and outputs to transmit and receive USB cable data Supports 12Mbps "Full Speed" and 1.5Mbps "Low Speed" serial data transmission Compatible
User Manual. CANopenIA-M0. Starter Kit
User Manual CANopenIA-M0 Starter Kit Edition 8 March 2017 Page 2 of 21 The information given in this document was compiled and checked carefully. Nevertheless ESS assumes no liability for any mistakes.
SP233A,SP310A and SP312A
SP233A,SP310A and SP312A Enhanced RS-232 Line Drivers/Receivers FEATURES Operates from a Single 5V Power Supply Meets all RS-232F and ITU V.28 Specifications Operates with 0.1μF Ceramic Capacitors No External
High Current Power Switch
SP619 High Current Power Switch FEATURES Max RDS(ON).377 Ohms Overcurrent deactivation 800mA Max leakage current less than 2µA while deactivated Small 6 pin SOT-23 package Built-in Over-temperature Protection
UM0212 User manual. STOTG04 USB OTG full-speed transceiver demonstration board. Introduction
UM0 User manual STOTG04 USB OTG full-speed transceiver demonstration board Introduction This manual explains how to use and take full advantage of the STOTG04 universal serial bus (USB) on-the-go (OTG)
USB Port MTT Hub
USB 2.0 4-Port MTT Hub General Description The is a USB 2.0 4-port hub using multiple transaction translators (MTT) for highest possible bandwidth capability. The upstream USB interface has an integrated
INTRODUCTION: DOWNLOADING & INSTALLATION:
INTRODUCTION: PowerArchitect TM is Exar s intuitive and easy-to-use software for developing power supplies with the XRP7724, XRP7720, XRP7725, XRP9711, and XRP9710 family programmable power management
GENERAL DESCRIPTION APPLICATIONS FEATURES TYPICAL APPLICATION DIAGRAM
August 2009 Rev. 2.0.0 GENERAL DESCRIPTION The SP6686 is a current-regulated charge pump ideal for powering high brightness LEDs for camera flash applications. The charge pump can be set to regulate two
PAC5523EVK1. Power Application Controllers. PAC5523EVK1 User s Guide. Copyright 2017 Active-Semi, Inc.
PAC5523EVK1 Power Application Controllers PAC5523EVK1 User s Guide www.active-semi.com Copyright 2017 Active-Semi, Inc. CONTENTS Contents...2 Overview...3 PAC5523EVK1 Resources...5 Pinout and Signal Connectivity...5
Evaluation Board for CS3308. Description CS Channel. Digitally Controlled Analog Volume Control. PC or External Serial Control Input
Evaluation Board for CS3308 Features Description Single-ended Analog Inputs Single-ended Analog Outputs Supports AC and DC-Coupled Analog I/O Flexible Serial Control I/O Headers Serial Control Input Header
XR21V1410 GENERAL DESCRIPTION 1-CH FULL-SPEED USB UART
JUNE 2009 REV. 1.0.0 GENERAL DESCRIPTION The XR21V1410 (V1410) is an enhanced Universal Asynchronous Receiver and Transmitter (UART) with a USB interface. The USB interface is fully compliant to Full Speed
USB Port Hub. Description. Typical Application. USB Host. Upstream Phy XR Hub Controller MTT. Port Routing.
USB 2.0 7-Port Hub Description The XR22417 is a USB 2.0 7-port hub using Multiple Transaction Translators (MTT) for highest possible bandwidth capability. The upstream USB interface has an integrated USB
GENERAL DESCRIPTION EVALUATION BOARD MANUAL
s June 2012 Rev. 1.1.1 GENERAL DESCRIPTION The XRP7714EVB-DEMO-1, XRP7714EVB- DEMO-2, and the XRP7714-DEMO-2P Demo boards are complete, working, four channel, power systems measuring either 2 x 2, or 2
High Performance RS-232 Line Drivers/Receivers
SP202E,SP232E, SP233E, SP310E and SP312E High Performance RS-232 Line Drivers/Receivers FEATURES Operates from a Single +5V Power Supply Meets all RS-232D and ITU V.28 Specifications Operates with 0.1μF
Figure 1. CP2108 USB-to-Quad UART Bridge Controller Evaluation Board
CP2108 EVALUATION KIT USER S GUIDE 1. Introduction The CP2108 is a highly integrated USB-to-Quad-UART Bridge Controller providing a simple solution for updating RS-232/RS-485 designs to USB using a minimum
For pricing, delivery, and ordering information, please contact ISSI at or call
IS3AP488D Class-AB Audio Amplifier Evaluation Board Guide Description The IS3AP488D demo board is a fully assembled and tested PCB that uses the IS3AP488D Class-AB a dual bridge-connected audio power amplifier.
EZ-USB FX3 Development Kit Guide
CYUSB3KIT-001 EZ-USB FX3 Development Kit Guide Doc. #: 001-70237 Rev. *A Cypress Semiconductor 198 Champion Court San Jose, CA 95134-1709 Phone (USA): 800.858.1810 Phone (Intnl): 408.943.2600 http://www.cypress.com
Universal PMIC 40V Quad Output Digital PWM/PFM Demo Board
December 2014 Rev. 1.0.0 GENERAL DESCRIPTION The XR77129EVB-DEMO-1 board is a complete four channel power system. It is configured to provide 5.0V, 12V, 3.3V and 2.5V at a maximum of 5A, 3A, 5A and 10A
Universal PMIC Quad Output Digital PWM/PFM Demo Board
December 2014 Rev. 1.0.0. GENERAL DESCRIPTION The XR77128EVB-DEMO-1 board is a complete four channel power system. It is configured to provide 3.3V, 2.5V, 1.5V and 1V at a maximum of 3A, 3A, 5A and 10A
XRD8775 CMOS 8-Bit High Speed Analog-to-Digital Converter
CMOS 8-Bit High Speed Analog-to-Digital Converter April 2002-4 FEATURES 8-Bit Resolution Up to 20MHz Sampling Rate Internal S/H Function Single Supply: 5V V IN DC Range: 0V to V DD V REF DC Range: 1V to
IS31AP4066D CLASS-AB AUDIO AMPLIFIER
ISAP466D CLASS-AB AUDIO AMPLIFIER DESCRIPTION The ISAP466D demo board is a fully assembled and tested PCB that uses the ISAP466D Class-AB dual bridge-connected audio power amplifier. Designed to drive
F2MC MB90385 series Evaluation Board Documentation. Revision Date Comment V New document
F2MC MB90385 series Evaluation Board Documentation Revision Date Comment V1.0 08.25.02 New document 1 Warranty and Disclaimer To the maximum extent permitted by applicable law, Fujitsu Microelectronics
Chapter 2 ICB Architecture Chapter 3 Board Components GPIO Interface RS-232 Interface RS-485 Interface...
1 CONTENTS Chapter 1 Introduction... 3 1.1 Features...3 1.2 About the Kit...4 1.3 Getting Help...5 Chapter 2 ICB Architecture... 6 2.1 Layout and Components...6 2.2 Block Diagram of the ICB...7 Chapter
ST78C34 GENERAL PURPOSE PARALLEL PRINTER PORT WITH 83 BYTE FIFO DESCRIPTION. PLCC Package FEATURES ORDERING INFORMATION
GENERAL PURPOSE PARALLEL PRINTER PORT WITH 83 BYTE FIFO DESCRIPTION The ST78C34 is a monolithic Bidirectional Parallel port designed to operate as a general purpose I/O port. It contains all the necessary
xpico Wi-Fi Embedded Device Server Evaluation Kit User Guide
xpico Wi-Fi Embedded Device Server Evaluation Kit User Guide Part Number 900-643-R Revision B July 2013 Copyright and Trademark Warranty Contacts 2013 Lantronix, Inc. All rights reserved. No part of the
SILICON MICROSTRUCTURES
Digital Communication with SM5800 Series Parts OVERVIEW The SM5800 series pressure product offers the corrected pressure output in both analog and digital formats. Accessing the analog output is an easy
XRD87L85 Low-Voltage CMOS 8-Bit High-Speed Analog-to-Digital Converter
Low-Voltage CMOS 8-Bit High-Speed Analog-to-Digital Converter April 2002-1 FEATURES 8-Bit Resolution Up to 10 MHz Sampling Rate Internal S/H Function Single Supply: 3.3V VIN DC Range: 0V to V DD VREF DC
HYDRA-X23/X23S. Power Application Controllers. PAC HYDRA-X User s Guide. Copyright 2014 Active-Semi, Inc.
HYDRA-X23/X23S Power Application Controllers PAC5223 - HYDRA-X User s Guide www.active-semi.com Copyright 2014 Active-Semi, Inc. CONTENTS Contents...2 Overview...3 HYDRA-X23/X23S Body Resources...5 Header
ic-mhm EVAL MHM1D EVALUATION BOARD DESCRIPTION
Rev A3, Page 1/12 ORDERING INFORMATION Type Order Designation Description Evaluation board ic-mhm EVAL MHM1D ic-mhm evaluation board Ready-to-operate, includes adapter MHM3M, accessible by GUI using PC
UG271: CP2615-EK2 User's Guide
The CP2615 device is designed to enable rapid development of USB-based audio applications. The CP2615 simplifies the process of transferring audio data from USB to I2S without any code development, speeding
E IO-Link Transceiver Evaluation Kit PCB 2 (with external transistor)
E981.10 IO-Link evaluation Kit PCB 2 (with external transistor) AN 006 E981.10 IO-Link Transceiver Evaluation Kit PCB 2 (with external transistor) 1 What you get - E981.10 IO-Link Evaluation Kit PCB 2
VLSI AppNote: VSx053 Simple DSP Board
: VSx053 Simple DSP Board Description This document describes the VS1053 / VS8053 Simple DPS Board and the VSx053 Simple DSP Host Board. Schematics, layouts and pinouts of both cards are included. The
EX-9686U/A-L(A9) Hardware User Manual
EX-9686U/A-L(A9) Hardware User Manual Release Notes Version Release Date Notes 1.00 November, 2013 Initial Release 2.00 January, 2014 The 2 nd release Disclaimer This documentation is provided for use
PCIe-400 USER S MANUAL
PCIe-400 USER S MANUAL 2017 May Edition Titan Electronics Inc. Web: www.titan.tw The computer programs provided with the hardware are supplied under a license. The software provided should be used only
IS31AP4991 CLASS-AB AUDIO AMPLIFIER
IS3AP499 CLASS-AB AUDIO AMPLIFIER DESCRIPTION The IS3AP499 demo board is a fully assembled and tested PCB that uses the IS3AP499 Class-AB power amplifier to drive an 8Ω or larger speaker in portable audio
ZSSC4151 Evaluation Kit Hardware Manual
Important Notes Restrictions in Use IDT s ZSSC4151 SSC Evaluation Kit, consisting of the SSC Communication Board (SSC CB), ZSSC415x/6x/7x Evaluation Board (SSC EB), Sensor Replacement Board (SSC RB), and
Preliminary. PACKAGE - 28-pin MLP (5mm X 5mm) Example Circuit Diagram CP V. 48MHz Oscillator. USB Function Controller 512B EEPROM
Preliminary Single-Chip USB to UART Bridge SINGLE-CHIP USB to UART DATA TRANSFER - Integrated USB Transceiver; No External Resistors Required - Integrated Clock; No External Crystal Required - Integrated
PCI Express 4-Port Industrial Serial I/O Cards
PCI Express 4-Port Industrial Serial I/O Cards The PCIe-400i and PCIe-400i-SI PCI Express 4-port industrial serial I/O cards are plug & play high-speed serial I/O expansion cards for the PCI Express bus.
Display Real Time Clock (RTC) On LCD. Version 1.2. Aug Cytron Technologies Sdn. Bhd.
Display Real Time Clock (RTC) On LCD PR12 Version 1.2 Aug 2008 Cytron Technologies Sdn. Bhd. Information contained in this publication regarding device applications and the like is intended through suggestion
Chapter 1 Introduction Features Getting Help Chapter 2 ICB Architecture Layout and Components...
1 CONTENTS Chapter 1 Introduction... 2 1.1 Features... 2 1.2 Getting Help... 3 Chapter 2 ICB Architecture... 4 2.1 Layout and Components... 4 2.2 Block Diagram of the ICB... 5 Chapter 3 Board Components...
October 2012 Rev FEATURES
October 2012 Rev. 1.0.0 GENERAL DESCRIPTION The XRP7724 controller includes an I2C serial command interface for performing numerous common tasks. This document covers details on the command types and their
EMX-ESG User Manual. EMX I/O Module with 2 Gigabit Ethernet, 6 Serial Ports, and 14 GPIO
EMX-ESG User Manual EMX I/O Module with 2 Gigabit Ethernet, 6 Serial Ports, and 14 GPIO Revision Date Comment A.0 2/17/2013 Initial Release A.1 3/5/15 Jumper information enhanced FOR TECHNICAL SUPPORT
Easy Kit Board Manual
User s Manual, V1.0, June2008 Easy Kit Board Manual Easy Kit - XC88x Microcontrollers Edition 2008-06 Published by Infineon Technologies AG, 81726 München, Germany Infineon Technologies AG 2008. All Rights
This manual provides information for the final user application developer on how to use SPC57S-Discovery microcontroller evaluation board.
User manual SPC570S-DISP: Discovery+ Evaluation Board Introduction This manual provides information for the final user application developer on how to use SPC57S-Discovery microcontroller evaluation board.
or between microcontrollers)
: Communication Interfaces in Embedded Systems (e.g., to interface with sensors and actuators or between microcontrollers) Spring 2016 : Communication Interfaces in Embedded Systems Spring (e.g., 2016
LAN9303 Evaluation Board User Manual
Copyright 2009 SMSC or its subsidiaries. All rights reserved. Circuit diagrams and other information relating to SMSC products are included as a means of illustrating typical applications. Consequently,
KSZ9692PB User Guide Brief
KSZ9692PB User Guide Brief KSZ9692PB Evaluation Platform Rev 2.0 General Description The KSZ9692PB Evaluation Platform accelerates product time-to-market by providing a hardware platform for proof-of-concept,
Also available for purchase separately are socket daughter boards for the QFN-11 and QFN-10 packages.
C8051T606 DEVELOPMENT KIT USER S GUIDE 1. Kit Contents The C8051T606 Development Kit contains the following items: C8051T606 Main Board C8051T606 MSOP Socket Daughter Board for programming MSOP devices
HYDRA-X10. Power Application Controllers TM. PAC HYDRA-X User s Guide. Copyright 2014 Active-Semi, Inc.
HYDRA-X10 Power Application Controllers TM PAC5210 - HYDRA-X User s Guide www.active-semi.com Copyright 2014 Active-Semi, Inc. CONTENTS Contents...2 Overview...3 HYDRA-X10 Body Resources...5 Header Descriptions...5
ET-UARTSWD Users Guide
User s Guide ET-UARTSWD Users Guide Power Application Controller s www.active-semi.com Copyright 2018 Active-Semi, Inc. CONTENTS Contents...2 Overview...3 1. ET-UARTSWD Resources...6 1.1 Provided Connectors...6
Skywire Hardware Design Checklist NimbeLink Corp Updated: August 2018
Skywire Hardware Design Checklist NimbeLink Corp Updated: August 2018 PN 1001787 rev 2 NimbeLink Corp. All Rights Reserved. 1 Table of Contents Table of Contents 2 Introduction 3 Scope 3 Orderable Devices
EVB-USB2514Q48 48-Pin QFN Evaluation Board Revision A1
EVB-USB2514Q48 48-Pin QFN Evaluation Board Revision A1 Copyright 2007 SMSC or its subsidiaries. All rights reserved. The information contained herein is proprietary to SMSC and shall be used solely in
ic-msb EVAL MSB1D EVALUATION BOARD DESCRIPTION
Rev A2, Page 1/7 ORDERING INFORMATION Type Order Designation Description and Options Evaluation Board ic-msb EVAL MSB1D ic-msb Evaluation Board ready to operate, accessible through GUI via PC adapter Software
6LoWPAN Development Platform Saker Manual
6LoWPAN Development Platform Saker Manual WEPTECH elektronik GmbH Page 1 of 19 V.1.0.1 1. Table of Content 1. General information... 4 1.1 1.2 1.3 1.4 1.5 Copyright protection... 4 Warranty information...
HX2VL Development Kit Guide. Doc. # Rev. **
HX2VL Development Kit Guide Doc. # 001-73960 Rev. ** Cypress Semiconductor 198 Champion Court San Jose, CA 95134-1709 Phone (USA): 800.858.1810 Phone (Intnl): 408.943.2600 http://www.cypress.com Copyrights
XR21V1412 GENERAL DESCRIPTION 2-CH FULL-SPEED USB UART FEATURES
2-CH FULL-SPEED USB UART DECEMBER 2013 REV. 1.3.0 GENERAL DESCRIPTION The XR21V1412 (V1412) is an enhanced 2-channel Universal Asynchronous Receiver and Transmitter (UART) with a USB interface. The USB
RE866 Interface User Guide
RE866 Interface User Guide 1VV0301387 Rev.0 6/16/2017 [04.2016] Mod. 0809 2016-08 Rev.7 SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE NOTICE While reasonable efforts have been made to assure the
AN3001 Application note
Application note Demonstration board user guidelines for the TS4657 single supply stereo digital audio line driver Introduction This application note focuses on the TS4657 demonstration board, designed
BC-USB-Kit Manual. First Edition. February, BeatCraft, Inc.
BC-USB-Kit Manual First Edition February, 2015 BeatCraft, Inc. 1. Overview BC-USB-Kit is a USB-gadget development kit, which is equipped with a micro controller of Microchip Technology Inc, PIC24FJ128GB202
PI5USB30213AXEA Demo Board Rev.B User Manual
PI5USB30213AXEA Demo Board Rev.B User Manual Table of Contents 1 Introduction... 2 2 Overview... 2 3 Quick Start... 4 3.1 Source(DFP) Mode... 4 3.2 Battery-powered Sink(UFP) Mode... 5 3.3 Bus-powered Sink(UFP)
Cytron USB to UART Converter UC00A
Cytron USB to UART Converter UC00A User s Manual V1.1 August 2009 Information contained in this publication regarding device applications and the like is intended through suggestion only and may be superseded
EMX-ESG User Manual. EMX I/O Module with 2 Gigabit Ethernet, 6 Serial Ports, and 14 GPIO
EMX-ESG User Manual EMX I/O Module with 2 Gigabit Ethernet, 6 Serial Ports, and 14 GPIO Revision Date Comment A.0 2/17/2013 Initial Release FOR TECHNICAL SUPPORT PLEASE CONTACT: Copyright 2013 Diamond
BIGdsPIC6. Development System. User manual
BIGdsPIC6 User manual All s development systems represent irreplaceable tools for programming and developing microcontroller-based devices. Carefully chosen components and the use of machines of the last
UM0592 User manual. STEVAL-PCC006V1, HDD bridge extension board. board for mass storage applications. Introduction
User manual STEVAL-PCC006V1, HDD bridge extension board for mass storage applications Introduction This document explains the use of the HDD extension demonstration board (STEVAL- PCC006V1) which can be
PremierWave 2050 Enterprise Wi-Fi IoT Module Evaluation Kit User Guide
PremierWave 2050 Enterprise Wi-Fi IoT Module Evaluation Kit User Guide Part Number 900-765-R Revision A February 2016 Intellectual Property 2016 Lantronix, Inc. All rights reserved. No part of the contents
USB Debug Adapter. Power USB DEBUG ADAPTER. Silicon Laboratories. Stop. Run. Figure 1. Hardware Setup using a USB Debug Adapter
C8051F35X-DK DEVELOPMENT KIT USER S GUIDE 1. Kit Contents The C8051F35x-DK Development Kit contains the following items: C8051F350 Target Board C8051Fxxx Development Kit Quick-Start Guide AC to DC Power
xpico 110 Wired Device Server Module Evaluation Kit User Guide
xpico 110 Wired Device Server Module Evaluation Kit User Guide Part Number 900-788-R Revision A April 2017 Intellectual Property 2017 Lantronix, Inc. All rights reserved. No part of the contents of this
RN-174. WiSnap M2 Super Module. Features. Description. Applications. ~ page 1 ~ rn-174-ds v1.1 6/1/2011
WiSnap M2 Super Module Features Development board containing the RN-171 module, status LEDs, power regulator Supports chip antenna (RN-174-C), PCB Trace antenna (RN-174-P), wire antenna (RN- 174-W) and
BIG8051. Development system. User manual
BIG8051 User manual All s development systems represent irreplaceable tools for programming and developing microcontroller-based devices. Carefully chosen components and the use of machines of the last
E Demonstration Board AN 0178 Dec 15, 2016
E.0 Demonstration Board AN 0 Dec, 0 E.0 Power LIN.X Stepper with Stall Detection What you get. Demoboard E.0 What you need in addition. V Power Supply, capable of providing the motor current. Bipolar stepper
ic-pv EVAL PV1D EVALUATION BOARD DESCRIPTION
Rev A1, Page 1/10 ORDERING INFORMATION Type Order Designation Description Options Evaluation Board ic-pv EVAL PV1D ic-pv Evaluation Board Ready-to-operate, supplied with magnet, accessible by GUI using
Future Technology Devices International Ltd
Future Technology Devices International Ltd Datasheet Debug Cable for Raspberry Pi Datasheet The cable provides USB to TTL Level UART solutions and 1 Introduction is customised for operation with the Raspberry
CDB5346. Evaluation Board for CS5346. Features. Description CS5346. Single-ended Analog Inputs. Single-ended Analog Outputs
Evaluation Board for CS5346 Features Description Single-ended Analog Inputs Single-ended Analog Outputs CS8406 S/PDIF Digital Audio Transmitter Header for Optional External Software Configuration of CS5346
SP336E Evaluation Board Manual Rev 2.1
SP336E Evaluation Board Manual 11-23-10 Rev 2.1 Features Easy Evaluation of the SP336E Transceiver RS-232 and RS-485 Protocols Local or Remote Loop Back testing 10Mbps Differential Transmission Rates Test
CDB4350 Evaluation Board for CS4350
Evaluation Board for CS4350 Features Description No High Frequency Master Clock Required Stand-Alone or PC GUI Board Control CS8416 Receives S/PDIF-Compatible Digital Audio Headers for External PCM Audio
STR710-EVAL. Evaluation Board for STR71xF. Main components. Description. Features. STR710-EVAL board
Evaluation Board for STR71xF STR710-EVAL board Host to JTAG interface High speed JTAG debug port connection Main components STR710F processor running at 48 MHz EMI SRAM 4 Mbytes (2M x 16) EMI flash 4 Mbytes
Installation Guide of Hi-Speed USB to Octal RS-232/422/485 Adapter
Installation Guide of Hi-Speed USB to Octal RS-232/422/485 Adapter Introduction The USB to Octal Serial Adapter is designed to make serial port expansion quick and simple. Connecting to a USB port on your
USB Debug Adapter. Power USB DEBUG ADAPTER. Silicon Laboratories. Stop. Run. Figure 1. Hardware Setup Using a USB Debug Adapter
C8051F34X DEVELOPMENT KIT USER S GUIDE 1. Kit Contents The C8051F34x Development Kit contains the following items: C8051F340 Target Board C8051Fxxx Development Kit Quick-Start Guide AC to DC Power Adapter