CONTA-ELECTRONICS. Fuse, component, diode and indicator modules

Transcription

1 Fuse, component, diode and indicator modules In the passive electronics sector, CONTA-CLIP offers a large variety of module types which support fast, secure, and compact functionality. These modules can be mounted with their combi-base on either the TS 32 or TS 35 DIN rails. They feature a screw PCB terminal connection with a rated crosssection of 2.5 mm². Customer-specific descriptions can be attached using the standard PMC Pocket-Maxicard Quick marking system. The PMCs fit on labelling channels located on both sides of the orange-coloured fitting trough.

2 Fuse, component, diode and indicator modules Fuse modules SM The SM fuse modules are designed with three or six micro-fuse receptacles. Each is separated with screw-pcb terminals. The fuse receptacles can hold micro-fuses in the 5x20 size. In the...g designs, the entries for the fuse receptacles are connected to each other via the PCB. This allows for a shared power supply. Component modules BSM The BSM component module features two rows of solder pins, attached parallel to the PCB. They are connected via circuit tracks, with screw-pcb terminals. The area on the opposite side to the solder pins may be used for soldering on a variety of user-side components, such as resistors, diodes, capacitors or varistors. Diode modules DM Different components, such as diodes or diodes with resistors, can be connected in parallel or in series using the DM diode modules. These diode circuits fulfil a variety of tasks in the area of electrical and electronic controls. These include: protection against polarity reversal, the electric decoupling of warning signals, spark-repression diodes for overvoltages from inductive loads such as magnet valves or DC relays, and lamp test modules for the detection and decoupling of group status messages. The modules are available in minus-pole or plus-pole designs, or as freely-switchable units. S-, B-, D-, A-modules Lamp test modules LPM The LPM lamp test modules are for the detection and decoupling of group status messages. They serve as visual indicators of the switching or signal status. The LPM-K modules feature diodes which are connected in pairs on the cathode side. They are freely-switchable on the anode. On the modules, the diodes are connected in pairs on the cathode side. One anode from the connected pair is connected to a common collection point with the other anodes. 143

3 Fuse modules SM Modules delivered standard with 3 or 6 fuse cartridges Suitable for 5x20 fuse cartridges Available upon request with individually-switched fuse paths, or as a distributor with a shared feedin SM E Individually switchable SM G Shared feed-in SM 3-E SM 3-G Cat. no./qty / /1 87 x 24 x 77 mm 87 x 24 x 77 mm 51 g 51 g SM 6-E SM 6-G Cat. no./qty / /1 87 x 47 x 77 mm 87 x 47 x 77 mm 104 g 104 g DIN-VDE specifications Operating temperature -20 to +50 C -20 to +50 C Stripping length 7 mm 7 mm Wire connect cross-section 0.2 to 2.5 mm to 2.5 mm 2 Screw connection AWG AWG Max. operating voltage 250 V AC 250 V AC Rated current 6.3 A max. per current path 4 A max., with simultaneous loads 6.3 A max. per current path 4 A max., with simultaneous loads Max. load at point L1 16 A 16 A Standard fuse 6.3 A 6.3 A 144

4 Component modules BSM BSM Two rows of soldering pins for versatile assembly with components BSM 4 Cat. no./qty /1 87 x 27 x 57 mm 45 g 2 rows for 4 poles BSM 4/AD* Cat. no./qty /1 87 x 27 x 57 mm 62 g 2 rows for 4 poles BSM 8 Cat. no./qty /1 87 x 47 x 57 mm 79 g 2 rows for 8 poles BSM 8/AD* Cat. no./qty /1 87 x 47 x 57 mm 102 g 2 rows for 8 poles BSM 12 Cat. no./qty /1 87 x 68 x 57 mm 100 g 2 rows for 12 poles BSM 12/AD* Cat. no./qty /1 87 x 68 x 57 mm 135 g 2 rows for 12 poles DIN-VDE specifications Operating temperature -20 to +50 C -20 to +50 C -20 to +50 C Stripping length 7 mm 7 mm 7 mm Wire connect cross-section 0.2 to 2.5 mm to 2.5 mm to 2.5 mm 2 Screw connection AWG AWG AWG Distance between pins 35 mm 35 mm 35 mm Height of soldering pins approx. 5 mm approx. 5 mm approx. 5 mm Solder pin grid/pitch 5.08 mm 5.08 mm 5.08 mm Max. operating voltage 250 V AC 250 V AC 250 V AC Max. rated current 5 A 5 A 5 A S-, B-, D-, A-modules *The.../AD modules must be used when the operating voltage exceeds 30 V AC/60 V DC. 145

5 Diode modules DM DM 26-A DM 26-K Diode modules with freely switchable diodes, and also diode gates with shared anodes or shared cathodes These modules can be used for protection against reverse polarity, decoupling, and arc suppression DM 26-A DM 26-K Cat. no./qty / /1 87 x 46 x 72 mm 87 x 46 x 72 mm 115 g 115 g DM 26-A/AD* DM 26-K/AD* Cat. no./qty / /1 87 x 46 x 72 mm 87 x 46 x 72 mm 140 g 140 g 104g 104g DIN-VDE specifications Operating temperature -20 to +50 C -20 to +50 C Stripping length 7 mm 7 mm Wire connect cross-section 0.2 to 2.5 mm to 2.5 mm 2 Screw connection AWG AWG Max. operating voltage 250 V AC/DC 250 V AC/DC Diode reverse voltage 1000 V 1000 V Max. diode current 0.5 A 0.5 A Total current per module 10 A 10 A Diode type 1 N N 4007 Reverse current of diode 5 µa 5 µa On-state voltage of diode 0.8 V 0.8 V *The.../AD modules must be used when the operating voltage exceeds 30 V AC/60 V DC. Designs with other diode types are available upon request. 146

6 Diode modules DM DM DM-A DM-K Diode modules with freely switchable diodes, and also diode gates with shared anodes or shared cathodes These modules can be used for protection against reverse polarity, decoupling, and arc suppression DM 4 DM 14-A DM 14-K Cat. no./qty / / /1 87 x 27 x 57 mm 87 x 49 x 57 mm 87 x 49 x 57 mm 44 g 80 g 80 g DM 4/AD* DM 14-A/AD DM 14-K/AD Cat. no./qty / / /1 87 x 27 x 57 mm 87 x 49 x 57 mm 87 x 49 x 57 mm 62 g 101 g 101 g DM 8 DM 22-A DM 22-K Cat. no./qty / / /1 87 x 47 x 57 mm 87 x 68 x 57 mm 87 x 68 x 57 mm 78 g 109 g 109 g DM 8/AD* DM 22-A/AD DM 22-K/AD Cat. no./qty / / /1 87 x 47 x 57 mm 87 x 68 x 57 mm 87 x 68 x 57 mm 99 g 138 g 138 g DM 12 Cat. no./qty /1 87 x 69 x 57 mm 107 g DM 12/AD* Cat. no./qty /1 Size (L x W x H) with TS3 5 x x 69 x 57 mm 135 g DM 14 Cat. no./qty /1 87 x 46 x 57 mm 116 g DM 14/AD Cat. no./qty /1 87 x 46 x 57 mm 147 g DIN-VDE specifications Operating temperature -20 to +50 C -20 to +50 C -20 to +50 C Stripping length 7 mm 7 mm 7 mm Wire connect cross-section 0.2 to 2.5 mm to 2.5 mm to 2.5 mm 2 Screw connection AWG AWG AWG Max. operating voltage 250 V AC/DC 250 V AC/DC 250 V AC/DC Diode reverse voltage 1000 V 1000 V 1000 V Max. diode current 1 A 1 A 1 A Total current per module - 6 A 6 A Diode type 1 N N N 4007 Reverse current of diode 5 µa 5 µa 5 µa On-state voltage of diode 0.8 V 0.8 V 0.8 V S-, B-, D-, A-modules *The.../AD modules must be used when the operating voltage exceeds 30 V AC/60 V DC. Designs with other diode types are available upon request. 147

7 Lamp test modules LPM Lamp test modules for the detection and decoupling of group status messages The LPM-K modules feature diodes which are connected in pairs on the cathode side. They are freely-switchable at the anode. The LPM-A modules feature diodes which are connected in pairs on the cathode side. One anode from the connected pair is connected to a common collection point with the other anodes. LPM LPM-A LPM 8-4K LPM 7-A Cat. no./qty / /1 87 x 49 x 57 mm 87 x 49 x 57 mm 74 g 80 g LPM 8-4K/AD* LPM 7-A/AD* Cat. no./qty / /1 87 x 49 x 57 mm 87 x 49 x 57 mm 96 g 109 g LPM 12-6K LPM 11-A Cat. no./qty / /1 87 x 68 x 57 mm 87 x 68 x 57 mm 100 g 110 g LPM 12-6K/AD* LPM 11-A/AD* Cat. no./qty / /1 87 x 68 x 57 mm 87 x 68 x 57 mm 130 g 198 g LPM 20-10K LPM 20-A Cat. no./qty / /1 87 x 109 x 57 mm 87 x 115 x 57 mm 152 g 176 g LPM 20-10K/AD* LPM 20-A/AD* Cat. no./qty / /1 87 x 109 x 57 mm 87 x 115 x 57 mm 190 g 215 g LPM 40-A Cat. no./qty /1 87 x 216 x 57 mm 325 g LPM 40-A/AD* Cat. no./qty /1 87 x 216 x 57 mm 390 g DIN-VDE specifications Operating temperature -20 to +50 C -20 to +50 C Stripping length 7 mm 7 mm Wire connect cross-section 0.2 to 2.5 mm to 2.5 mm 2 Screw connection AWG AWG Max. operating voltage 250 V AC/DC 250 V AC/DC Diode reverse voltage 1000 V 1000 V Max. diode current 1 A 1 A Total current per module - - Diode type 1 N N 4007 Reverse current of diode 5 µa 5 µa On-state voltage of diode 0.8 V 0.8 V *The.../AD modules must be used when the operating voltage exceeds 30 V AC/60 V DC. Designs with other diode types are available upon request. 148