Joystick base J2... Multi-axis, small version. Use. Options. + space-saving design

Transcription

1 Joystick base Multi-axis, small version J space-saving design + highly reliable and long lifetime thanks to contactless Hall Effect and reed technology + analog output signal (current/voltage, also redundant) or switching output possible + high electronics protection class of IP67 for tough conditions + operating temperature range -25 C to +85 C + deflection ± + single or dual-axis + EMV stability for the motor vehicle sector: Field withstand 200 mv/m + CAN-Bus and PWM signals can be implemented Use Due to its compact design, the J2 joystick is ideally suited for use in control panels, armrests etc. in the commercial vehicle and farm machinery industries. Due to high electronics protection class IP67, it withstands humidity and debris. Armrest with installed J2 Options Actuation can be implemented either on a oneor two-axis basis. Current and voltage signals are available as output signals, as is a switching output with individual switching points. A CAN-Bus capable or PWM signal can also be implemented. The electronics can also be executed redundantly. In addition, there is room for up to 3 additional push buttons on the installed standard handle. J2 with three push buttons J2 Version 1.3 Page 1 of 5

2 Mechanical assembly S1 S2 S3 S1 S2 analoger range Bereich analogue range S3 knob (alternative) A B C X-Achse X-axis axe X Y-Achse Y-axis axe Y Ø ,8 8x LifY-t 0,75mm 2 2x LifY 0,25mm ±15 Taste button bouton M4 / 8,5 tief / deep Signal 2 0,3V 0,5V Signal 1 4,7V 4,5V ,3V 2,7V 2,7V 2,3V Signal 2 Signal 1 0,3V 4,7V 0,5V 4,5V 2,3V 2,7V 2,7V 2,3V 4,5V 0,5V 4,7V 0,3V 4,5V 0,5V 4,7V 0,3V **Assembly Aufbauhöhe für height Ausführung for Schaltausgang switching output / Redundant / redundant / CAN / CAN version panel thickness for execution Switching output / redundant / CAN dimension pour version TOR / redondante / CAN = empfohlener Toleranzbereich = recommended tolerance range = Plage de tolérance recommandée Installation dimensions *Assembly height for switching output / redundant / CAN version Installation opening for standard handle Installation size Mounting Height of actuating handle joystick without handle: 60 x 60 x 52 mm joystick with handle: 60 x 60 x 144 mm threaded holes for 4x M4 screws approx. 89 mm Key mechanical data Technology analog: contactless Hall sensor technology; switching output: reed technology Mechanical life 1 m cycles Deflection ± Lever rod metal Torsional moment 4.0 Nm x-axis/y-axis 250 N Point of application from pivot point 70 mm Storage temperature range C Operating temperature range C Protection class electronic/reed IP67 DIN EN EMV stability 200 V/m DIN Connection Molex connector 300 ± 15 mm one elobau cycle corresponds to one oscillation of the joystick in all four directions Crank J2 Version 1.3 Page 2 of 5

3 Key electrical data Analog J2 A1... J2 A6... J2 A7... Operating voltage VDC VDC VDC Output signal ma VDC ratiometric VDC Current consumption per signal at 12 V max. 18 ma max. 15 ma at 12 V max. 15 ma Load resistance U B 10V: <250Ω; 30V: <1250Ω > 20 kω > 20 kω Center position 12 ma 2.5 V typical 2.5 V typical Output signal delay approx. 3 ms approx. 3 ms approx. 3 ms Reverse connection protected yes yes yes Switching output J2 D8... Switching voltage max. 48 V Switching current max. 0.3 Switching power max. 10 W/VA Contact form 3x N.O.(normally open) CAN-Bus / PWM Button Switching voltage Switching current Switching power Contact form Illumination/icons 145 MT max. 48 V max. 0.5 A max. 10 W/VA N.O.(normally open) Wiring Analog (both x- and y-axis) Switching output (both x- and y-axis) Analog redundant (both x- and y-axis) CAN To detect the center position, both S2 contacts of the x- and y- axis must be interconnected with "AND". Connection type Standard version Alternative design 4 / 6 / 8 / 10 or 12-PIN Molex 5557 connector strand length: 300 ±15 mm J2 Version 1.3 Page 3 of 5

4 Fax: Specifications of your joystick without handle Handle version A = standard handle B = standard handle with button C = handle with 3 buttons S = handle acc. to customer specification Locking device 0 = center position cannot be mechanically locked 1 = center position can be mech. locked Actuation 0 = multi-axial 1 = north, south, west, east (mandatory when digital) 2 = single axis End position y-axis A = no detent B = detent End position x-axis A = no detent B = detent EMV stability A = motor vehicle industry 200 V/m Output signal 1 = analog ma 6 = analog VDC ratio. 7 = analog VDC 8 = 3 switching points/axis Electronics A = analog C = CAN capable D = digital R = analog redundant acc. to customer specification J2 Version 1.3 Page 4 of 5

5 Fax: Your product enquiry Quantity Batch size Name / first name Company Address Postal code / town Country Notes, questions, other J2 Version 1.3 Page 5 of 5