Sensus RTM II. Description. Applications. Features and Benefits. Smart Communication Gateway and Control DDS Features

Transcription

1 DDS Sensus RTM II Smart Communication Gateway and Control Description The Sensus Remote Telemetry Module (RTM II) is a cost-effective communication solution for remote monitoring and control of Intelligent Electronic Devices (IEDs) that control electric distribution system assets such as reclosers, switches, capacitor banks, breakers, voltage regulators, and meters. The RTM II enables remote firmware updates, includes a USB port, and communicates using cellular communication networks or Sensus FlexNet networks. The device communicates with any IED that supports DNP3/IEEE 1815 or Modbus protocol. End-to-end interoperability is then achieved with the AutomationControl software suite. This allows for easy integration with third-party SCADA software platforms via our SCADA-Xchange interface. Applications The devices are ideally suited for smart grid distribution automation applications such as reclosers, capacitor banks, distribution switches, faulted circuit indicators, voltage regulators, distributed generation, load control, and distribution substations. Models with FlexNet radios communicate using packet data over the Sensus FlexNet networks. The devices can be installed on any FlexNet system that is configured to support the AutomationControl application platform. Models with cellular radios configured to support the AutomationControl application platform communicate using the AT&T 4G/LTE/3G or Verizon 4G/LTE cellular data networks. The devices can be installed anywhere AT&T or Verizon service is available, including their roaming partners. The RTM II continuously polls connected IEDs through a local serial connection. When a userdefined change is detected, the RTM II transmits an event report via the cellular or FlexNet network. This minimizes communication traffic while providing real-time information. Status of equipment is obtained through the Sensus AutomationControl application with a standard PC browser or via the utility s SCADA system using Sensus SCADA Xchange. Features and Benefits Monitors status of IEDs and reports userconfigured data, events, and alarms Designed specifically to communicate with IEDs from leading manufacturers such as Cooper Power Systems, ABB, Schweitzer Engineering Laboratories, S&C Electric Company, GE, T&B/ Joslyn Hi-Voltage, ICMI and many others Communicates via standard RS 232 serial connection with IEDs. The RTM II functions as the master in the master-slave relationship, polling the IED for information. Supports up to five DNP3 device addresses, supporting a different DNP/IEC point map/ profile Features Flexible smart utility communication options: FlexNet and/or 4G/LTE cellular data networks Two-way communication Interoperability: Supports over a hundred different IED integrations for 19 separate applications Remote monitoring and control of IEDs using standard DNP3 or Modbus protocols Automated user notifications for userconfigured data, events, and alarms Real-time equipment status information using AutomationControl and a standard Internet browser SCADA interface Remote firmware updates Local configuration utility included

2 Supports intelligent reporting and control via: - Unsolicited Report-by-Exception on userdefined analog or digital points - Time scheduled reports on user-selected points and defined time intervals - Updates are available on demand via SCADA or the AutomationControl application Information is sent to the AutomationControl application at the Sensus Data Center, and optionally to the utility SCADA system Secure two-way communications allow direct status queries and control of the IED Integration kits, including specific device point maps/profiles, are available for most popular IEDs to facilitate simple and easy installation Unique configuration profiles are created using AutomationControl for all SCADA points that are monitored and reported. Users can specify SCADA point criteria such as: - Multiple reporting set points and a configurable trigger time per analog input - Binary input report-on-change with configurable trigger time - Time scheduled reports with configurable reporting interval from 1 minute up to 14 days AutomationControl The AutomationControl application is a powerful and flexible suite of tools for managing communications and distribution system equipment. Access equipment status from any PC using a standard browser Each user has a secure account that provides access to their equipment Data is secure and password protected A SCADA system is not required. Utilities can utilize AutomationControl with or without SCADA connectivity. Manage equipment, communications, and users Monitor and control field equipment Automated user notifications provide immediate information on events such as a recloser lockout or low voltage/outage conditions Device history logs all communications with equipment Request equipment status and analog values at any time Encryption and key rotation. Sensus uses industry-standard Advanced Encryption Standard (AES) 256-bit key encryption to secure data in transit over the FlexNet system. Sensus offers AutomationControl as a flexible and secure cloud-based Software as a Service (SaaS) solution. Features (continued) Supports intelligent reporting and control Three reporting methods: Report by exception Time-scheduled reports Response to report requests Integration kits provided for most popular IEDs for easy installation Software and hardware data transmission security with firewalls and strong encryption algorithms 24/7 monitoring and maximum safety and reliability through SaaS and the Sensus Data Center

3 SCADA Interface All Sensus Automation devices can be monitored and controlled through an existing SCADA or DMS system via DNP3/IEEE 1815 protocols and the Sensus SCADA-Xchange interface. Additional Software Tools Two additional software tools are part of the AutomationControl suite: Automation Device Configurator and IED Remote Connect Client. Both are Microsoft Windows based utilities installed locally on a PC. Automation Device Configurator provides a way to install, power up, and commission a device in the field, which then receives configuration settings from AutomationControl. A standard USB connection is used to connect a PC directly to the Sensus device. IED Remote Connect Client provides an interface to connect remotely to an IED through a Sensus device. Specifications Processor 32 bit microcontroller, 72 MHz 8 MB non-volatile Flash memory 32 MB RAM Communications General Two-way communication: All communications are acknowledged for reliability Three Serial Ports USB 2.0 compliant local configuration port; supports Microsoft Windows based local configuration and test program RS-232 SCADA communications port, DB-9 female or terminal block; supports DNP or Modbus RS-232 pass-through for IED maintenance port connection, DB-9 female FlexNet Network Transmit power: 2W Frequency: 900 MHz band Primary licensed SMA antenna connector Cellular Network AT&T: 4G/LTE with 3G Fallback Verizon: 4G/LTE Transmit power: 3G: 2W (GSM), 0.25W (WCDMA) 4G: 0.2W (LTE) Frequency: 3G: 850/1900 MHz 4G: 700/850/1700/1900 MHz (2) SMA antenna connectors (Main and Diversity) Environmental Data Operating temperature range: FlexNet: -40º to +185º F (-40º to +85ºC) Cellular: -40º to +158º F (-40º to +70ºC) Humidity: 0% to 95% non-condensing Radiated emissions: FCC 47 CFR Part 15B and ICES-003 Enclosures Standard enclosure features include: NEMA 1 or IP 20 rating (International) Integrated mounting flanges Gray steel construction Dimensions: See drawings on the last page Features (continued) Device monitoring and control through a SCADA or DMS system and SCADA Xchange Included software tools: Automation Device Configurator IED Remote Connect Client Hardened steel construction Tested to be fully operational in temperature extremes Models Models with FlexNet radios communicate using packet data over Sensus FlexNet networks. The units can be installed on any FlexNet system that is configured to support the AutomationControl application platform. Models with cellular radios configured to support the AutomationControl application platform communicate using the AT&T 4G/LTE/3G or Verizon 4G/LTE cellular data networks. The devices can be installed anywhere AT&T or Verizon service is available, including their roaming partners. Model Radio Frequency Protocol FlexNet 900 MHz DNP and Modbus AT&T Cellular 4G (LTE) with 3G Fallback 700/850/1700/1900 MHz DNP and Modbus Verizon Cellular 4G (LTE) 700/850/1700/1900 MHz DNP and Modbus

4 Supported IEDs The RTM II supports over a hundred different integrations for 19 separate applications. The table below shows the current list of supported IEDs and applications. New integrations are added regularly. Contact a Sensus sales to find out more. Manufacturer IED Application Protocol ABB CQ900 Capacitor Bank Control DNP ABB DPU2000 Recloser Control DNP ABB ISD Recloser Control DNP New integrations are added regularly. to find out more. ABB PCD2000 Recloser Control DNP ABB RER620 Recloser Control DNP ABB TPU2000 Recloser Control DNP ACS Custom Custom DNP Advanced Power Technology TTC-1000 Transformer Monitor DNP Areva Bitronics Meter DNP Areva M571 Meter DNP Areva MiCom P14 Feeder Protection Relay DNP Beckwith M-2001-B Tapchanger Control DNP Beckwith M-2001-C Tapchanger Control DNP Beckwith M-6200A Voltage Regulator Control DNP Beckwith M-6280A Capacitor Bank Control DNP Cannon CBC-7000 Capacitor Bank Control DNP CG Automation ecap II Capacitor Bank Control DNP Cooper Aries Recloser Control DNP Cooper CBC-8000 Capacitor Bank Control DNP Cooper CL-5 Voltage Regulator Control DNP Cooper CL-6 Voltage Regulator Control DNP Cooper Form 4D Recloser Control DNP Cooper Form 5 Recloser Control DNP Cooper Form 5 - LS Recloser Control DNP Cooper Form 5 - TS Recloser Control DNP Cooper Form 6 Recloser Control DNP Cooper Form 6 - LS Recloser Control DNP Cooper Form 6 - TS Recloser Control DNP Cooper SMP4 Gateway Data Concentrator DNP DirectLogic DL05 PLC Modbus Eaton Cutler Hammer MPCV Network Protector DNP Eaton Cutler Hammer VaultGard Network Protector DNP Electro Industries DMSS300 Series Meter DNP Electro Industries Nexus 1250 Meter Modbus Electro Industries Nexus 1250 Meter DNP

5 Supported IEDs Continued Manufacturer IED Application Protocol ETI MNPR Network Protector DNP GE DART Power Quality Monitor DNP GE Kelman TRANSFIX Transformer Monitor DNP GE Harris D25 Substation Control DNP Gridsense DataPac Faulted Circuit Indicator DNP New integrations are added regularly. to find out more. Gridsense TransformerIQ Transformer Monitor DNP HD Electric VARCOM 1600 Capacitor Bank Control DNP ICMI UVR-1 Voltage Regulator Control DNP Itron Q1000 Meter DNP Landys & Gyr MaxSys Elete Meter DNP Lindsey Smartpin Faulted Circuit Indicator DNP Maysteel 100 Series Capacitor Bank Control DNP Maysteel ProCap Capacitor Bank Control DNP Morgan Schaffer Calisto 2 Environmental Monitor DNP MPE ISD Pump Control Modbus Multitrode MultiSmart Pump Control Modbus Novexia Auguste Switch Control DNP NOJA RC01 Recloser Control DNP NOJA RC10 Recloser Control DNP Nulec ACO Recloser Control DNP Nulec ACR Recloser Control DNP Optisense OSP Power Quality Monitor DNP PowerLogic ION8600 Meter DNP PVPowered PVP100kW Inverter Modbus PVPowered PVP30kW Inverter Modbus PVPowered PVP75kW Inverter Modbus QEI 6ACP5 Switch Control DNP QEI ecap II Capacitor Bank Control DNP Red Lion Data Station Plus PLC Modbus Reliatronics RTU2000 Switch Control DNP S&C 4801 Switch Control DNP S&C 5801 Switch Control DNP S&C 5802 Switch Control DNP S&C 5803 Switch Control DNP S&C 6801 Switch Control DNP S&C 5801 IntelliTeam II Switch Control DNP S&C 5802 IntelliTeam II Switch Control DNP

6 Supported IEDs Continued Manufacturer IED Application Protocol S&C EnergyLine 1000 Capacitor Bank Control DNP S&C IntelliCap Plus Capacitor Bank Control DNP S&C IntelliRupter PulseCloser Switch Control DNP S&C M-series Switch Control DNP S&C Vista Switch Control DNP New integrations are added regularly. to find out more. Sage 1450 PLC DNP Sage 2100 PLC DNP Satec PM130 Meter DNP Satec PM172 Meter DNP Schneider Electric Bardin G200 Faulted Circuit Indicator DNP Schneider Electric MUCM PLC DNP Schneider Electric PowerLogic ION7300 Meter DNP SEL SEL-2032 Data Concentrator DNP SEL SEL-2414 Transformer Monitor DNP SEL SEL-2431 Voltage Regulator Control DNP SEL SEL-321 Feeder Protection Relay DNP SEL SEL Feeder Protection Relay DNP SEL SEL-351J Recloser Control DNP SEL SEL-351P Recloser Control DNP SEL SEL-351R Recloser Control DNP SEL SEL-351R-1 Recloser Control DNP SEL SEL-351R-2 Recloser Control DNP SEL SEL-351RS Recloser Control DNP SEL SEL-351S Recloser Control DNP SEL SEL-3530 RTAC Substation Control DNP SEL SEL-451R Recloser Control DNP SEL SEL-451S Recloser Control DNP SEL SEL-487V Capacitor Bank Control DNP SEL SEL-651R Recloser Control DNP SEL SEL-700GW Wind Generator Relay DNP SEL SEL-734B Capacitor Bank Control DNP SEL SEL-751A Feeder Protection Relay DNP Siemens Hydroranger 200 Pump Control Modbus Siemens IntraLink LC150 Pump Control Modbus Siemens MJRL Recloser Control DNP Siemens MJXL Voltage Regulator Control DNP

7 RTM II drawing shows a FlexNet model. All measurements are in inches with a +/ inch tolerance. to see for yourself W Emerald Street, Suite 100 Boise, ID Sensus. All rights reserved. FlexNet and the Sensus logo are registered trademarks of Sensus. AutomationControl, NaviComm, Remote Telemetry Module, SCADA-Xchange, SCADA-Master, T866 MicroRTU, and TC032 MicroRTU are trademarks of Sensus. T: (208) (option 1) F: (208) automation.support@sensus.com