Elements Collection Technical
|
|
- Drusilla Robbins
- 6 years ago
- Views:
Transcription
1 Elements Collection Technical wiring devices decorative MK Elements Collection Installation The MK Elements Collection products consist of the main product module, complete with its support frame, plus a separate clip on frontplate. The product is mounted to the wall, after wiring, and the frontplate is clipped onto the frame. The frontplate is supplied separately to aid installation.. Ensure the depth of the back box is correct for the product and that it is fitted securely to the wall.. Install the cables in the normal way and, using the fixing screws supplied, mount the product, still minus its frontplate, to the wall. It is important the correct headed screws are used as any other may clash with the rear of the front plate.. Do not over tighten the screws, so as to prevent damage or distortion to the product or support frame. Adjust so the frame or module sits squarely on the wall.. Locate the top and bottom hooks on the back of the frontplate into the holes on the top and bottom of the module.. Gently push along the top edge of the frontplate followed by the bottom edge.. Carefully insert a mm screwdriver into the slots provided along the bottom edge frontplate.. Carefully twist the screwdriver and lift the frontplate away disengaging the snap fits. Note: Ensure the correct frontplate is fitted to the correct module or frame Footnote: Care should be taken to ensure product features such as snap fits are not blocked during installation or decorating, preventing correct fitting of frontplates (for example plaster, tile grout, paint etc).
2 Elements Collection Technical technical hotline + (0) decorative wiring devices Electronic Switches All CE marked Elements Electronic Switches comply with the EC Low Voltage Directive: 7// EEC, Electromagnetic Compatibility Directive 89/6/EEC They also comply with IEC Mains Supply Voltage: 0-0V a.c. 0/60Hz Mains Supply Voltage Range: 98-6V a.c. Mains Supply Frequency: 0/60Hz ±Hz Terminal capacity: All products x mm x.mm x.mm x mm x 6mm Operating temperature: 0 C to + C IP rating: IPX Elements Electronic Switches offer intuitive touch sensitive silent switching (except K70) with LED displays, for a unique user experience. l Touch sensitive electronic switch with LED display l Standby light to assist location in low light level applications l Soft start and off offers superior user experience and prolongs lamp life l Available as and gang l LED compatible l High power switches up to 0A of fluorescent load (0Ax) l Intelligent overload protection l -way switching available l Patent Pending Max. installation altitude: 000 metres To prevent damage to front plates during installation it is recommended that a screwdriver with a blade width of.mm is used. gang 8. MOUNTING BOX TYPE: The minimum depth required is mm. When using.mm² cables the minimum box depth required is 0mm. gang 8.
3 Elements Collection Technical wiring devices decorative Electronic Switches Load rating and type K7 & K7 (per gang) K70 GLS/ Tungsten Filament, Mains Tungsten Halogen 00W -00W Fluorescent tubes with ferro-magnetic ballast with power factor correction *8-00VA 8-800W Fluorescent with electronic ballast *8-00VA 8-0W Low Energy PL-C and PL-S Fluorescent with Ferromagnetic ballast *8-00VA 8-70W Low Energy PL-C and PL-S Fluorescent with electronic ballast *8-00VA *8-70W Compact Fluorescent (CFL) *-00W *-70W ELV Tungsten Halogen with Ferro-magnetic transformer or Dimmable Electronic Transformer 0-00VA (Refer to note ) 0-00VA (Refer to note ) ELV Tungsten Halogen with Non-dimmable Electronic Transformer *-00VA 00VA Mains LED lamp for incandescent replacement Ceiling Fan (Note: Not suitable for fan with remote controller function) Ventilation Fan Dimmable or non-dimmable LED Driver *-0W (Max. lamps) Not applicable *- Max. 0W *-0W (Max 0 LED drivers only) *-00W (Max. lamps) *- Max. 0W *-00W (Max 0 LED drivers only) Note:. Do not use loads of different types on the same circuit.. Not suitable for use with any other load type.. *Neutral connection is required. It is recommended to connect neutral whenever possible to extend the load handling capability of the switch.. If neutral is connected to the switch then the minimum rating of the load can be reduced to VA.
4 Elements Collection Technical technical hotline + (0) decorative wiring devices Electronic Dimmers All CE marked Elements Electronic Dimmers comply with the EC Low Voltage Directive: 7// EEC, Electromagnetic Compatibility Directive 89/6/EEC They also comply with IEC Mains Supply Voltage: 0-0V a.c. 0/60Hz Mains Supply Voltage Range: 98-6V a.c. Mains Supply Frequency: 0/60Hz ±Hz Terminal capacity: All products x mm x.mm x.mm x mm x 6mm Note: For -0V control cable of K99 x 0.7mm² x mm² x.mm² x Cat e Cable Elements Electronic Dimmers offer intuitive touch sensitive silent dimming with LED displays, for a unique user experience. l Touch sensitive electronic dimmer with LED display l LED Vapour trail follows users finger to indicate the power level l Standby light to assist location in low light level applications l Soft start and off offers superior user experience and prolongs lamp life l When switched on lights return to last setting l Available as and gang l LED compatible l Intelligent overload protection l Leading edge and trailing edge dimmers available l -way control available l Patent Pending Operating temperature: 0 C to + C IP rating: IPX Max. installation altitude: 000 metres To prevent damage to front plates during installation it is recommended that a screwdriver with a blade width of.mm is used. gang 8. MOUNTING BOX TYPE: The minimum depth required is mm. When using.mm² cables the minimum box depth required is 0mm. gang 8.
5 Elements Collection Technical wiring devices decorative Electronic Dimmers Load rating and type Leading Edge Dimmers K00 K0 & K0 (per gang) GLS/ Tungsten Filament, Mains Tungsten Halogen 0-00W 0 00W Mains dimmable LED lamp for incandescent replacement 6-0W Max. lamps 6-0W Max. lamps ELV Tungsten Halogen with dimmable Ferro-magnetic transformer - 00VA - 0VA Trailing Edge Dimmers K0 K0 & K0 (per gang) GLS/ Tungsten filament, Mains Tungsten Halogen 00W 00W ELV Tungsten Halogen with Dimmable Electronic Transformer 00VA 00VA Dimmable LED Driver *-0W (Max LED drivers only) *-0W (Max LED drivers only) Note:. Do not use loads of different types on the same circuit.. Not suitable for use with any other load type.. *Neutral connection is required. It is recommended to connect neutral whenever possible to extend the load handling capability of the dimmer. -0V Dimmer K99 Rated Load 6AX Maximum number of ballasts 0 Neutral connection is mandatory on -0V Dimmer. Suitable for use with dimmable fluorescent or LED lighting which is driven by separate 0/-0V control gear. Suitable for use with 0/-0V analogue dimmable ballast operating in accordance with IEC6099 annex E. Note: This product is only suitable for use with ballasts which are the source of the control voltage. It is not suitable for any other load type.
6 Elements Collection Technical 6 technical hotline + (0) decorative wiring devices Socket Outlets A socket outlets comply with BS 6 Part, MS89, SS, SASO0, IS. A range of socket outlets designed for ease of installation and having all the advantageous design features of the Elements Collection. The two gang switch socket and one gang unswitched socket are fitted with one earth terminal, the one gang switch socket is fitted with two earth terminals on a common busbar to provide a double earth facility for use when installations require a high integrity protective connection as specified within BS 767: 008. The products can be quickly installed as replacements for existing amp sockets or in a new installations (if suitable mounting box is in position). Round pin sockets A range of round pin sockets is also available. l 6 standard finishes l Many more customised combinations of standard colours, materials and finishes available l Bespoke colours, materials and finishes available via the Design Service l Products with LED locators and indicators available l pin operated shutter l Printed terminal markings on grey rear mouldings for clearer identification l Top access, angled terminals make wiring easier and quicker l mm minimum switch contact gap l Double pole switching l Additional electrical safety from neutral make first, break last feature l Switch contacts with silver contacts on both surfaces for good continuity l Only one size of screwdriver required for installation l Dual earth terminals for high integrity earthing on Gang Switched Socket Outlet l Backed out and captive terminal screws
7 7 Elements Collection Technical wiring devices decorative Amp Socket Outlets Elements A socket outlets comply with A socket outlets comply with BS 6 Part, MS89, SS, SASO0, IS 0V a.c. Current rating: A gang 9. Terminal capacity: Live, neutral & earth x.mm x mm x 6mm (stranded) Ambient operating temperature: C to +0 C (not to exceed an average of more than C in any hour period) IP rating: IPXD Max. installation altitude: 000 metres Installation gang 6 9. Elements socket outlets can be wall or bench mounted. Do not mount or use as a trailing socket or where they may be subject to excessive moisture or dampness. Flush Flush (for extra wiring space) gang 6ZIC 877ZIC gang 8ZIC 878ZIC Footnote: Care should be taken to ensure product features such as snap fits are not blocked during installation or decorativng, preventing correct fitting of frontplates (for example plaster, tile grout, paint etc).
8 Elements Collection Technical 8 technical hotline + (0) decorative wiring devices Round Pin Socket Outlets Round pin socket outlets comply with BS6, MS77 and SS7 0V a.c. A range of round pin socket outlets designed for ease of installation and having all the advantages and design features of the Elements Collection. These products can be quickly installed as replace ments for existing socket outlets or in new installations. Terminal capacities: amp sockets (K8): x.mm x mm x 6mm (stranded) amp sockets (K8): x.mm x mm x 6mm (stranded) l mm minimum switch contact gap l Only one size of screwdriver required for installation l AMP Round Pin Socket Outlets available in 6 standard finishes l AMP Round Pin Socket Outlets available in Synthetic Chalk White finish only Ambient operating temperature: C to +0 C (not to exceed an average of more than C in any hour period) IP rating: IPXD Amp Max. installation altitude: 000 metres.8 Installation Elements socket outlets can be wall or bench mounted do not mount or use as a trailing socket or where they may be subjected to excessive moisture or dampness. Flush 6ZIC Flush for extra wiring space 877ZIC Amp.
9 9 Elements Collection Technical wiring devices decorative Shaver/Toothbrush Supply Unit Shaver/Toothbrush supply units comply with BS EN 68--: 998. Accommodates plugs as follows: l British mm dia pins on 6.6mm pitch (0V socket) to BS 7: 970 l European mm dia pins on 7 to 9mm pitch (0V socket) to CEE 7/6 Euro Type C to BS EN 007 l Australian 6. x.6 flat blades each set at 0 to the vertical on a nominal pitch of.7mm (0V socket) CEE 7/6 Euro Type C to BS EN 007 l American 6.6 x.6 flat horizontal blades on.7mm pitch (V socket) to NEMA - - Type A to UL98/NEMA WD6 K709: 0V a.c. Input (will operate at 0-0V a.c.) 0V or V nominal outputs Current rating: K709: 00mA max. (internal thermister trip current) Maximum load: 0VA No load voltage < 7V Terminal capacities: Each terminal will accommodate x mm or x.mm solid conductors* Ambient operating temperature: C to +0 C Designed for ease of installation and having many of the advantageous design features of the Elements Collection. May be used in bathrooms and washrooms but must only be installed in accordance with BS 767: 008. Top access terminal screws make wiring quicker and easier Automatic primary supply switching on insertion of plug Choice of 0V or V output socket positions Safety interlocked shutters to prevent insertion of two plugs simultaneously Only one size of screwdriver required for installation Front plate fixing screws retained on rear case moulding Integral over current device to protect transformer Suitable for use with electric toothbrush chargers. IP rating: IP (In Zone if fixed where direct spray from showers is unlikely) Max. installation altitude: 000 metres *The design of this unit means that on no load the transformer output is allowed to be as high as 7V. This means that rechargeable shavers and toothbrushes intended for use on the continent may be damaged by the inrush current created by this higher voltage. Rechargeable shavers and toothbrushes with a wide range of input voltage should be recharged at V. Shavers and toothbrushes manufactured for the UK are designed to be used with a transformer unit. Loads in excess of 0VA may cause the solid state overload to operate before shaving is completed. This is to protect the transformer Installation Shaver/Toothbrush supply unit should be wall mounted. Flush mounting only Metal box 878ZIC (minimum metal mounting box depth is 7mm)
10 Elements Collection Technical 0 technical hotline + (0) decorative wiring devices Connection Units All Elements Connection Units comply with BS 6 Part, SS0: All units are fitted with a amp fuse* to BS 6. A range of A fused connection units designed for the connection of refrigerators, water heaters, central heating boilers and other fixed appliances. The range is designed for ease of instal la tion and has all the advantageous design features of the Elements Collection. Flex outlets The products are equipped with very strong, push-fit Deldrin cord grips making installation safe, quick and easy. Fuse carriers These are captive and are opened by a fast acting, worm-drive operated screwdriver for ease of replacement. l Worm-drive operated fuse carriers for additional security l Push-fit cord grips, for safer, quicker installation l Captive fuse carrier l Additional electrical safety from neutral make first, break last feature l All terminal and fixing screws operated by one-size (mm) screwdriver
11 Elements Collection Technical wiring devices decorative Connection Units 0V a.c. Current rating: amp Terminal capacity:. 0.7 Supply terminal: x.mm x mm x 6mm (stranded) Load terminals: x.mm x mm x 6mm (stranded) Flex outlet/cord grip capacities: Min. Core, 0.mm Max. Core,.mm EARTH terminal capacity x.mm x mm x 6mm Flush All units 6ZIC mm deep For extra wiring space use box 877ZIC (6mm deep) Ambient operating temperature: C to +0 C (not to exceed an average of more than C in any hour period) IP rating: With flex outlet: IPX Without flex outlet: IPX Max. installation altitude: 000 metres Installation Elements connection units can be wall or bench mounted. Do not use on a trailing lead. Changing Fuses. Unscrew the fuse carrier screw to partially eject the carrier.. Carefully lever (by screwdriver or finger) the carrier out further to remove the fuse. Note: The carrier does not come fully out.. Always replace with a BS 6 type fuse (as used in A plugs) of the correct rating.. Consistent fuse blowing could mean a faulty appliance. If in doubt, consult a qualified electrician.. Push carrier back until engaging with worm screw. Screw the carrier down until flush with surface of the plate. Do not over tighten the screw.
12 Elements Collection Technical technical hotline + (0) decorative wiring devices Grid Switch Modules All Elements switches comply with IEC/BS EN :999. 0V a.c. 0Hz Current rating: way/way - 0AX or 0AX versions available. All Push switches - 0A only Intermediate - 0AX only Double Pole - 0AX only Centre Off - 0A only Elements Modular Switches require a separate frontplate, when ordering ensure the appropriate module and frontplate is selected. Terminal capacity: All products x mm x.mm x.mm x mm x 6mm Contact gap: mm switch contact gap (Except K900 and K90) Operating temperature: C to +0 C IP rating: IPX l 6 standard finishes l Many more customised combinations of standard colours, materials and finishes available l Bespoke colours, materials and finishes available via the Design Service l Switch contacts with silver contacts in both surfaces for good continuity l Positive switch action l Only one size of screwdriver required for installation l Backed out and captive terminal screws l Locator versions available for low light level applications Max. installation altitude: 000 metres gang gang Operational testing (all plateswitches): tested to 00,000 operations for mechanical life tested to 0,000 operations at 0 amp rating..7 Flush and gang switches ZIC (mm deep) and gang switches ZIC (mm deep) gang wide rocker.7 Sectional drawings show the furthest projections from the back of the frontplate (wall surface).
13 Elements Collection Technical wiring devices decorative Grid Switch Modules Wiring Diagrams One-way switching L N Common Lamp/s Switches featuring locators and indicators use LED illumination. All switches fitted with a locator are intended to give a very low light output whilst the switch is turned off. The low level of power flowing in this circuit is compatible with the majority of installation requirements however, certain lamp types or installations using multiple intermediate switches on one circuit may require the use of a snubber capacitor. The recommended capacitor to use would be X rated 7V 0. µ F. Switches incorporating indicator or locator illumination must be disconnected before carrying out any site installation testing. Two-way switching wire control Common Common L N Two-way switches Lamp/s Dotted lines show alternative switch positions Two-way switching plus intermediate switching wire control Common Common L N Two-way switch Intermediate switch Two-way switch Lamp/s Dotted lines show alternative switch positions Two-way switching wire control Common Common L N Lamp/s SW.L Two-way switches Dotted lines show alternative switch positions Two-way switching plus intermediate switching wire control Common Common L N Lamp/s SW.L Two-way switch Dotted lines show alternative switch positions Intermediate switch Two-way switch N.B. Terminal positions may alter. The above diagrams are to show wiring layout.
14 Elements Collection Technical technical hotline + (0) decorative wiring devices Grid Switch Frontplates Frontplate module K module K module K module K 6 6
15 Elements Collection Technical wiring devices decorative High Current Switches These switches comply with BS EN SS7, IEC / MS IEC V a.c. Current: A Switch 0A Switch Switch: mm contact gap Double pole operation Terminal capacity, 0A Switches: x mm x 6mm x 0mm x 6mm Terminal capacity, A Switches: x.mm x mm x 6mm Ambient operating temperature: C to +0 C Max. installation altitude: 000 metres A range of switches harmonising with the Elements style, suitable for the switching of all domestic, commercial and industrial appliances where higher current ratings are required, i.e. cookers, heaters, commercial refrigeration units etc. Switches Max. Cable Size Flush A 0mm 6mm 0A 6mm 7mm BOX REFERENCES Flush Box depth A 0A 7mm 877ZIC 877ZIC A l Positive switch action l Positive double pole switching l Toggle action switches l Replaceable neon indicators Note: These switches are not recommended for switching large banks of PCs. 0A 7
16 Elements Collection Technical 6 technical hotline + (0) decorative wiring devices Do Not Disturb / Make Up Room Switches All Elements switches comply with IEC / BS EN :999. 0V a.c. 0Hz Current rating: 0 amps The Elements Do Not Disturb / Make Up Room Switches have been developed along with a number of other products for hotels and hospitality venues, offering guests comfort and control. The Do Not Disturb / Make Up Room Switches allow guests to offer indications to service staff from the bedside. Elements Modular Switches require a separate frontplate, when ordering ensure the appropriate module and frontplate is selected. Terminal capacity: All products x mm x.mm x.mm x mm x 6mm Contact gap: K900DND - Mini gap K88DND - Normal gap Operating temperature: C to +0 C IP rating: IPX Max. installation altitude: 000 metres l 6 standard finishes l Many more customised combinations of standard colours, materials and finishes available l Bespoke colours, materials and finishes available via the Design Service l All products clearly marked with BS numbers and ratings Room Switch l Switch contacts with silver contacts in both surfaces for good continuity l Positive switch action l Only one size of screwdriver required for installation l Backed out and captive terminal screws Connection of LED Indicators All switches Flush ZIC (mm deep).9 Corridor Switch.9 Room Switch - Inside Occupancy Selector Corridor Switch - Outside Bell Push/Indicator
17 7 Elements Collection Technical wiring devices decorative Keycard Switch with Time Delay Standards and Approvals IEC , BSEN , MSIEC , SS 7:Pt. 0-0V, 0/60Hz Current rating: 0A Terminal Capacity: x.mm x.mm x.0mm x 6.0mm Earth terminal: x.mm x.0mm x 6.0mm Contact Gap: Micro Gap The Elements Keycard Switch with Time Delay has been developed along with a number of other products for hotels and hospitality venues, offering guests comfort and control, whilst delivering energy efficiency by avoiding energy waste in unoccupied rooms. The Keycard Switch has a time delay once the card is removed ensuring guests are not left in the dark. Flush (mm) Flush (6mm for extra wring Gang 877ZIC 877ZIC.9. Ambient operating temperature: 0 C to + C IP Rating: IPX Max. installation altitude: 000m Time delay: 0 seconds Wiring Diagram l 6 standard finishes l Many more customised combinations of standard colours, materials and finishes available l Bespoke colours, materials and finishes available via the Design Service l All products clearly marked with BS numbers and ratings L in 0-0V~ N Time Delay Circuit L out Load
18 Elements Collection Technical 8 technical hotline + (0) decorative wiring devices Euro Frontplates BS 7: 00 Dimensions Frontplates for mounting Euro Modules. Height: Width: mm mm (G) Depth: 6mm (G) mm Aperture Dimensions gang module: K module: K Height: Width: 0mm mm G module 0mm G module 00mm G module l G and G frontplates l Elements style l Accept industry standard Euro snapfit modules l G Euro frontplate accepts or Euro modules, (0 x 0mm aperture) l G Euro frontplate accepts Euro modules, (00 x 0mm aperture) l Euro / module (. x 0mm) blank available l Interchangeable modules clip into frontplate gang module: K 6
19 9 Elements Collection Technical wiring devices decorative Power Modules K80: BS 6 Part : 99 K8: IEC 6088-: 006 K8: SASO 0: 00 K8: BS 6: 90 K8: French National Standard NF C 6- A range of euro modules designed to provide a variety of power options. A UK A UK 6A German A American A USB Charging Module 0V a.c. Current rating: A Terminal capacity: Live, neutral & earth x.mm x mm x 6mm (stranded) 0V a.c. Current rating: A Terminal capacity: Live, neutral & earth x.mm x mm x 6mm (stranded) 0V a.c. Current rating: 6A Terminal capacity: Live, neutral & earth x.mm x.mm x mm 7V a.c. Current rating: A Terminal capacity: Live, neutral & earth x.mm x mm x 6mm (stranded) Input 0-0V a.c. Frequency : 0/60Hz Rated Current: 0.A Terminal Capacity: Live & neutral x.mm x mm Output x V d.c. Max current: Charging sockets: USB.0 type A A can be delivered in total to either socket outlet, or be divided between the two. Ambient operating temperature: - C to +0 C (not to exceed an average of more than C in any hour period) Ambient operating temperature: - C to +0 C (not to exceed an average of more than C in any hour period) Ambient operating temperature: - C to +0 C (not to exceed an average of more than C in any hour period) Ambient operating temperature: - C to +0 C (not to exceed an average of more than C in any hour period) Ambient operating temperature: 0 C to +0 C This module is not limited to A from each socket outlet. IP rating: IPXD IP rating: IPXD IP rating: IPXD IP rating: IPXD IP rating: IPXD Max. installation altitude: 000 metres Max. installation altitude: 000 metres Max. installation altitude: 000 metres Max. installation altitude: 000 metres Max. installation altitude: 000 metres A UK A UK 6A German A American A USB Charging Module K80 K8 K8 K8 K87 Minimum Minimum Minimum Minimum Minimum mm mm 6mm mm mm Extra wiring space Extra wiring space Extra wiring space Extra wiring space 6mm 6mm 6mm 6mm
20 Elements Collection Technical 0 technical hotline + (0) decorative wiring devices RJ Data Outlets ISO/IEC 80 EN 07 TIA 68 EN 00 Installation l Maximum cable length 90m. l Cable bend radii, 0mm during installation, 0mm after installation. l Maximum pull force 8.7kg. l Do not over tighten cable ties. l Do not unwind the twists in the wire pairs by more than mm max B C D E F G H Euro and LJU6C modules are to be wired as follows RJ Cat.e Euro K8 Suitable for use in all LJU6C, Euro and MK Modular frontplates, available in the Logic Plus range, Cat e and Cat 6 modules suitable for use in structured cabling distribution systems. Installation details and wiring diagram illustrations TIA WIRING SCHEME COLOUR CODES: Pin No. 68A 68B WHITE / green WHITE / orange GREEN / white ORANGE / white WHITE / orange WHITE/ green BLUE / white BLUE / white WHITE / blue WHITE / blue P P P P P P D E F G H A B C D A 6 ORANGE / white GREEN / white Pair BLUE/white & WHITE/blue 7 WHITE / brown BWHITE / brown Pair ORANGE/white C & WHITE/orange Pair GREEN/white & WHITE/green D 8 BROWN / white BROWN / white Pair BROWN/white & WHITE/brown 6 6 RJ Cat.e Euro - Angled K P 68A RJ Cat.6 Screened K76S - LJU6C, K86S - Euro P 68B RJ Cat.e LJU6C K7 007 RJ Cat.6 Euro - Angled K76 - LJU6C K86 - Euro, K - Euro Angled RJ Cat.e Screened K8S - Euro 0079
21 Elements Collection Technical wiring devices decorative Telephone, RJ/, BNC Data and Blank Modules Telephone sockets K80 and K8 comply with the following: BS 6:. Data sockets K80, BS 7: 00 (where applicable). K887 complies with FCC68 and EN 00. Cable types: Telephone: CW, CW9, CW08, CW6 No. of cables per termination: Telephone: RJ/: BNC 0 Ohms impedance cable RG8, RG, URM Belden 9907 Frequency range: BNC connector: 0 to GHz Impedance: BNC Connector: 0. nominal Termination type: Telephone module IDC BNC module Crimped connection Temperature range: Ambient air 0 C to +60 C IP rating: IPXD K80, K8, K80 and K787. IPX K80, K88, K and K70 Max. installation altitude: 000 metres A range of telephone, data and blank modules to fit Euro and LJ6UC front plates. BNC Euro modules with a 0Ohm crimp connector suitable for use with RG8, URM, URM76 and Beldon 9907 type coaxial cables are also available. Installation (Telephone socket modules) Product performance, systems compatibility Master Sockets: For use as the first socket outlet on a direct exchange. They contain the required surge protector (for line protection against electrical surges) and ringing capacitor. Secondary Sockets: for use as extension sockets when connected on the same line as a Master Socket. Installation tools required IDC Connectors (telephone & RJ outlets) MK insertion tool List No. 00NAT. Wire pull-out force: 0. Newtons when installed correctly. Wiring regulation restrictions Domestic Installations: The total REN (Ring Equivalent Number) value of all telephone equipment connected on a line must not exceed. l Meet all relevant BS, OFTEL and cabling standards l Interchangeable modules clip into frontplates l Front fixing facilitates easy exchange of modules l Part of a complete range of products for telephone and data processing requirements Telephone sockets l 00% tested before delivery l Quick, simple and reliable IDC connectors l Can be specified for all applications Data sockets l Latest specification for high performance systems l Made to stringent quality assurance procedures l Wide range of data connectors available
22 Elements Collection Technical A B C technical hotline + (0) decorative wiring devices Telephone, A RJ/, BNC B Data and CBlank Modules D E Telephone Wiring Scheme GREEN / white BLUE / white ORANGE / white WHITE / orange WHITE / blue 6 WHITE / green Note: Main wire colour is shown in capitals 6 First Socket Outlet Master 6 6 K80 Extension Outlet Secondary K C D E F G H RJ/ Wiring Scheme PIN STRIPPED COLOUR SOLID COLOUR NO. WIRE WIRE 6 WHITE / green WHITE WHITE / orange BLACK BLUE / white RED 6 WHITE / blue GREEN ORANGE / white YELLOW 6 GREEN / white BLUE MODIFICATION TEXT: Note: Main wire colour is shown in capitals007 K K887 6 A B C MODIFICATION TEXT: R MK ELECTRIC (MALAYSIA) SDN. BHD C/O SYMPHONY CORPORATEHOUSE SDN.BHD ND FLOOR, MENARA EON BANK 88, JALAN RAJA LAUT 00 KUALA LUMPUR HONEYWELL CONFIDENTIAL AND PROPRIETARY A B C 6 8 PROTECTED BY DIN ISO 606 FIRST ANGLE PROJECTION UNITS DRAWN BY: MM GENERAL TOLERANCES: LINEAR ±0. HOLE DIA ±0.08 RADII ±0.0 ANGULAR ±0.0 DIMENSIONS AND T BRITISH STAN ECC ENGINEERIN MATERIAL FINISH PACKAGING SPEC No: PERMIT No: IMPRESSIONS: DRAWN BY DATE: MODIFICATION TEXT: R MK ELECTRIC (MALAYSIA) SDN. BHD C/O SYMPHONY CORPORATEHOUSE SDN.BHD ND FLOOR, MENARA EON BANK 88, JALAN RAJA LAUT DIMENSIONS AND TOLERANCES PER BRITISH STANDARDS AND ECC ENGINEERING STANDARDS ENVIRONMENTAL & COMBUSTION CONTROLS
23 Elements Collection Technical wiring devices decorative Digital TV, Radio and Telephone Outlets All MK Digital TV Outlets comply with BS 7 and BS EN 008 where applicable. Also IEC 69-, BS EN and BS 6 Part. Modular products are Euro compatible. Single Outlets TV/FM IEC Male or Female SATF-Type Diplexer and Triplexer products TV Diplexer: Triplexer: FM Diplexer: Triplexer: SAT Diplexer: Triplexer: -6MHz 70-MHz -6MHz 70-MHz MHz MHz n/a 90-00MHz DC-90MHz DC-.7GHz TV/FM/DAB/SAT products for digital radio There are two ranges of diplexer and triplexer products, an established range suitable for VHF TV, and a range suitable for digital radio (DAB). Diplexer modules are for connecting to a single co-axial aerial down lead carrying combined TV and FM signals. The filtering in the diplexer splits out the appropriate signal and feeds it to the relevant output connection. A DC control path is provided in the TV signal path through the diplexer. Triplexer modules are for connecting to a single co-axial aerial down lead carrying combined TV, FM and SAT signals. The filtering in the triplexer splits out the appropriate signal and feeds it to the relevant output connection. A DC control path is provided in the SAT signal path through the triplexer. The quad outlet contains a triplexer together with a separate satellite output, for use with Sky+, or more complex installations. Telephone secondary outlets are provided on some products for connection of telephone or for interactive TV applications. Euro module Euro module Triplexer Euro module Quadplexer TV Diplexer: Triplexer: FM/DAB -6MHz 70-MHz -6MHz 70-MHz Diplexer: Triplexer: SAT or SAT 87.-0MHz 87.-0MHz Note: Minimum box depth: 7mm Diplexer: Triplexer: SAT Diplexer: Triplexer: l Non Isolated n/a 90-00MHz n/a -00MHz Installation l When installing the TV Co-axial cable ensure that all cable bends are smooth so that the inner insulation is not crushed or squashed. Otherwise the TV signal quality may be affected. l Not suitable for loop-in loop-out installations. l Use CT00 cable (or equivalent.) Co-axial cable Earth terminal Cable clamping plate Foil EMC screening gasket Clamping plate fixing screws l Fully screened l Earth terminal provided on TV modules Earth terminal TV Co-axial cable stripping details Cable management Digital TV outlets can be mounted in a variety of MK trunking systems. Screening braid to remain in place over the inner insulation Co-axial cable Cable clamp Clamping fixing screws View with cable clamp removed
24 Elements Collection Technical technical hotline + (0) decorative wiring devices TV/FM and Satellite Socket Outlets Installation (TV sockets) Product performance, systems compatibility Isolated Outlets are intended for use where safety isolation (rated at 000V ac) is required to provide protection against faults occurring within any mains powered product used on different parts of the distribution system. They are not suitable for use in systems where DC signals are passed through the socket, (e.g. where masthead/headend equipment is controlled by receiver/decoder equipment). Diplexer Outlets are used in distribution systems where both TV and FM band signals are combined on a single aerial downlead. The filtering in the diplexer separates the appropriate signals and feeds them through to the relevant output connection port. Cable Routing and Use of Cable Clamp Sharp bends in the cable must be avoided during installation. The single TV/ FM socket is fitted with a cable clamp that can be fixed on either side of the termination position to facilitate this. When tightening the screening braid clamps ensure that the cable is firmly gripped and that the inner insulation is not squashed flat beyond a slight oval shape. Safety Information TV outlets or modules must not be installed in the same enclosure as equipment rated in excess of 0V, (e.g. mains rated A sockets or switches). TV VID TV FM DAB TV DIST TV TV VID SKY/DIG HI-FI TV SAT SAT Method of installation of TV and FM aerial connection by using MK co-axial socket outlet and only one downlead. Conventional distribution system for TV and FM signals using a single aerial downlead. The signals from the TV and FM aerials and the satellite dish are combined together using two products. The first combines the TV and FM signals and the second adds the Sky signal to the TV/FM signal and provides a DC control path to power the LNB unit on the satellite dish. (These products are not supplied by MK). The single aerial down lead feeds into the triplexer (black lines in wiring diagram). The separated satellite signal is then fed to the decoder. The decoded satellite signal is then fed into the VCR along with the TV signal from the Triplexer. The output signal from the VCR then feeds into the TV and also back to the single outlet and onto the distribution amplifier (black lines in wiring diagram). The single cable back-feed then feeds back to the input of a multi way distribution amplifier, (typically located in the loft or garage) (red lines in wiring diagram). Each individual output from the distribution amplifier is then fed to the individual rooms in the house to a standard TV (single or diplexer) outlet to which the TV/VCR and/or Hi-Fi can be connected (blue lines in wiring diagram).
25 Elements Collection Technical wiring devices decorative Modular Range: PIR Detector IEC :00+A:008 The Elements PIR Detector will deliver energy savings and lighting usage management in a wide range of applications. Offering effective and efficient detection for control of lighting, this stand alone solution is easy to install and program, with the additional benefit of variable time delay from 0 minutes to permanently on. 0-0V Current Rating: 0A Load Type: Incandescent Light (resistive Load): 00W HV Halogen Lamps: 00 W Inductive Load: 600VA Electronics Ballast: x 8W (max. inrush current 80A/0ms) Contact Gap: Micro gap Terminal Capacity (Screwless Terminal): Stranded Cbales x.mm l 6 standard finishes l Many more customized combinations of standard colours, materials and finishes available l Bespoke colour materials and finishes available via the Design Service l Detection range of 8m Frontplate and Module Installation WALL BOX PATRESS l Delivers energy saving by switching lights off when occupancy is not detected l Offers safety and comfort by switching lights on when occupancy is detected l Easy to install and program l Time delay from 0 minutes to permanently on Solid Cables x.mm x mm MODULE WITH METAL PLATE Earth Terminal (screw terminal): x.mm x.0mm x 6.0mm Ambient operating temperature: 0 C to + C Max installation altitude: 000 metres Installation For optimal detection and control sufficient distance (m minimum) should be maintained between the PIR Detector and lighting fixtures in order to prevent undesirable motion detector switching. The optimal installation height is 0.8m.m. Installation in areas where excessive air movement occurs can cause false activations. FRONTPLATE MOTION SENSOR MODULE gang Flush 6ZIC (mm) Flush for extra wiring space 877ZIC (7mm)
26 Elements Collection Technical 6 technical hotline + (0) decorative wiring devices Modular Range: Echo Transmitters BS EN , BS EN , ESTI EN & -, ESTI EN , ESTI EN00 0-, EN6090- Operating temperature: - C + 0 C Operating frequency: 8. MHz IP Rating: IPX Max installation altitude: 000m Mounting Transmitters l All transmitters can be mounted to any gang back box l All transmitters can be mounted directly to the wall surface The Elements Echo Transmitters are part of an innovative range of entirely wireless, batteryless and self powered switches only available from MK Electric. The Elements Echo Transmitters communicate with Echo receivers to switch mains power. Elements Echo Transmitters send an RF signal at 8. MHz, the unique feature of these transmitters is the signal transmission is made with no need for mains power or batteries. l 6 standard finishes l Many more customized combinations of standard colours, materials and finishes available l Bespoke colour materials and finishes available via the Design Service Frontplate and Module Installation PATRESS l Wireless and batteryless, using RF technology with ranges up to 0m in ideal conditions l The transmitters are quick and easy to install with no need for cabling from the switch to the lighting circuit l See the Echo range for available receivers MODULE PLATE LATCHES FRONTPLATE TRANSMITTER MODULE
27 7 Elements Collection Technical wiring devices decorative Modular Range: Roller Shutter / Blind Control Controller IEC60669-:998 + A999 + A:006 Voltage Rating: 0 VAC Current Rating: 0A The Elements Modular Roller Shutter / Blind Controller will operate a motor run device enabling the control of window coverings. Terminal Capacity: Stranded Cables x.mm x.0mm Solid Cables: x.mm x.0mm Earth Terminal: x.mm x.0mm x 6.0mm Ambient Operating Temperature: 0 C to + C IP Rating: IPX Max installation altitude: 000 metres l 6 standard finishes l Many more customized combinations of standard colours, materials and finishes available Frontplate and Module Installation WALL BOX PATRESS l Bespoke colour materials and finishes available via the Design Service l Easy to install FRONTPLATE ROCKER FRAME Installation For optimal performance ensure the product is orientated correctly. The wrong orientation may cause the product to function incorrectly. ROLLER SHUTTER MODULE ROCKER gang Flush (mm) Flush (6mm for extra wiring space) 6ZIC 877ZIC
28 Elements Collection Technical 8 technical hotline + (0) decorative wiring devices
Grosvenor Plus Technical
533 Grosvenor Plus Technical wiring devices decorative www.mkelectric.co.uk Socket Outlets Grosvenor Plus Decorative finish 3A socket outlets comply with BS 363: Part : 995. 50V a.c. 3A per socket outlet
More informationChroma Plus 130 decorative High quality, lustrous finish with modern curved design Total safety
30 Chroma Plus wiring devices decorative www.mkelectric.co.uk range introduction feature benefits Displaying a superior mirror-like finish, MK s Chroma Plus range brings a lustrous and iridescent quality
More informationMetalclad Plus Technical
TD83 TECHICAL HOTLIE +44 (0)68 56370 Socket Outlets All Metalclad Plus 3A socket outlets comply with BS 363: Part : 995. Electrical Voltage rating: 50V a.c. Current rating: 3A per socket outlet Terminal
More informationMetalclad Plus Technical
605 Metalclad Plus Technical wiring devices surface www.mkelectric.co.uk Socket Outlets Metalclad Plus 3A socket outlets comply with BS 363: Part : 995. Electrical Voltage rating: 50V a.c. Current rating:
More informationSlimline. Technical Hotline
Slimline Deta Slimline has quickly become established as a leading choice for professional installers throughout the country, so much so that it has received the highest accolade being specified by many
More informationAlloy. technical hotline +44 (0) decorative wiring devices
147 technical hotline +44 (0)1268 563720 decorative wiring devices range introduction features and benefits With a crisp clean edge and luxurious finishes of brushed nickel, black nickel and polished chrome,
More informationMetalclad Plus Technical
9 wiring devices surface www.mkelectric.co.uk Switchsocket Outlets Metalclad Plus A socket outlets comply with BS 6: Part : 99. Replacement fuses to the gang socket outlets comply with BS 6: 97. Electrical
More informationSwitchsocket Outlets. 382 Logic Plus Technical. wiring devices white. Standards and approvals. Description
38 Logic Plus Technical wiring devices white Switchsocket Outlets Logic Plus 3A socket outlets comply with BS 363: Part : 995. Replacement fuses to the 3 gang socket outlets comply with BS 36: 973. Voltage
More informationto modern interiors. As trends in contemporary décor increasingly include the use of chrome
08 Chroma Plus www.mkelectric.co.uk Displaying a superior mirror-like finish, MK s Chroma Plus range brings a lustrous and iridescent quality to modern interiors. As trends in contemporary décor increasingly
More informationLogic Plus Technical. Switchsocket Outlets TD1. Standards and approvals. Description. Technical specification
TD Switchsocket Outlets All Logic Plus 3A socket outlets comply with BS 363: Part : 995. Replacement fuses to the 3 gang socket outlets comply with BS 36: 973. Voltage rating: 50V a.c. Current rating:
More informationVimark. t: e: w: detaelectrical.co.uk
Product Catalogue 2018 is a long established and widely acclaimed range of high quality white moulded wiring accessories. Offering a comprehensive range of products, is suitable for new homes where a conventional
More informationLogic Plus. Logic Plus wiring devices from MK Electric have been designed to perfectly complement modern
8 Logic Plus www.mkelectric.co.uk Logic Plus wiring devices from MK Electric have been designed to perfectly complement modern interiors, offering an unobtrusive and sophisticated look totally in keeping
More informationLOGIC PLUSTM RANGE INTRODUCTION
LOGIC PLUSTM RANGE INTRODUCTION Logic PlusTM wiring devices from MK Electric have been designed to perfectly complement modern interiors, offering an unobtrusive and sophisticated look totally in keeping
More informationLogic Plus. wiring devices white
42 wiring devices white range introduction features and benefits Logic Plus TM wiring devices from MK Electric have been designed to perfectly complement modern interiors, offering an unobtrusive and sophisticated
More informationLogic Plus. wiring devices white.
8 Logic Plus wiring devices white www.mkelectric.co.uk range introduction feature benefits Logic Plus wiring devices from MK Electric have been designed to perfectly complement modern interiors, offering
More informationSlimline Plus. Catalogue No. R6. For reference only.
Slimline Plus Catalogue No. R6 slimline plus Stylish Robust Ease of installation Affordable For over 55 years, MK Electric has been a household name throughout the Asia Pacific region, trusted and respected,
More informationKalo Attraction in simplicity
Kalo Attraction in simplicity 2 KALO ATTRACTION IN SIMPLICITY 3 Kalo Attraction in simplicity The elegance of the Kalo design series lies in its simplicity and purity. The neutral white design perfectly
More informationWiring Devices Technical
Technical Hotline +44 (0)68 56370 WIRIG DEVICES Installation general information Socket outlets, switches and other MK wiring accessories can be wall or bench mounted. Do not use a trailing lead for sockets
More information10AX SP 1g/2w switch, min. 25mm deep back box required, IEC , BS EN , Rated Voltage: 250V, screw-type terminals, studiowhite
No. Description Manufacturer Part-No. technical picture 10AX Plateswitch 1G/2W studio A 1002 WHI 1 10AX SP 1g/2w switch, min. 25mm deep back box required, IEC 60669-1, BS EN 60669-1, Rated Voltage: 250V,
More informationDIMENSIONS Screwless Wiring Devices
Screwless Wiring Devices 2 MK Screwless Wiring Devices 3 WEALTH OF EXPERTISE STARTS HERE For almost 100 years, MK Electric has led the market in electrical wiring devices. Engineering excellence and manufacturing
More information訂 貨 熱 線 香 港 批 發 / 分 銷 澳 門 批 發 / 分 銷
Product Selector MK Elements Collection The MK Elements range is available in 16 standard finishes across 4 materials, Synthetics, Metallics, Glass Effect and Naturals. When selecting a product, first
More informationWIRING ACCESSORIES NEW PRODUCTS. Mallia TM complete white. Mallia TM customisable colours. Belanko TM. Plexo, Industrial sockets
Mallia TM complete white P. 7 Switches and push-buttons Mallia TM customisable colours P. 7 Switches and push-buttons and other lighting functions P. 69 Switches and push-buttons WIRING ACCESSORIES Belanko
More informationDecorative Flat Plate Electrical Accessories in Various Plate Finishes
Decorative Flat Plate Electrical Accessories in Various Plate Finishes Define unique product codes When ordering any Define products, please specify the required finish by following the simple code structure
More informationDecorative Flat Plate Electrical Accessories in Various Plate Finishes Issue 5
Decorative Flat Plate Electrical Accessories in Various Plate Finishes Issue 5 Switches Sockets Connection Units Fan Isolation Switches Blank Plates Cooker Control Panels Telephone and Data Outlets Coaxial
More informationDecorative Metal Wiring Accessories in Assorted Plate Finishes
Decorative Metal Wiring Accessories in Assorted Plate Finishes Deco unique product codes Decorative Metal Wiring Accessories in Assorted Plate Finishes When ordering any Deco products, please specify the
More informationErgonomic Electrical Accessories
Ergonomic Electrical Accessories Antimicrobial Certified Products A Stylish, Contemporary & Flexible Range of Smooth Profile Wiring Accessories All white moulded and Mode Part M wiring accessories are
More informationErgonomic Electrical Accessories
Ergonomic Electrical Accessories A Stylish, Contemporary & Flexible Range of Smooth Profile Wiring Accessories Contents Switches Back Boxes Power Socket Outlets 13A Fused Connection Units Control Switches
More informationBRITISH STANDARD WIRING ACCESSORIES NEW PRODUCTS Synergy. Sleek Design equipped mechanisms (p. 560 to 564)
P. 526 Switches and push-buttons Belanko TM P. 529 Socket outlets Mallia TM complete white P. 532 Switches and push-buttons BRITISH STANDARD WIRING ACCESSORIES Mallia TM customisable colours P. 539 Switches
More informationPlexo IP 55/IP 66. Makes your day, rain or shine PLEXO / WEATHERPROOF PRODUCT GUIDE. For reference only.
Plexo IP 55/IP 66 Makes your day, rain or shine PLEXO / WEATHERPROOF PRODUCT GUIDE www.legrand.com.sg Plexo IP 55 Ingenious features for easy installation >> Time saving guaranteed: no cut-out Uncut pierceable
More informationSuno TM switches, push-buttons, dimmers, roller blind controls
switches, push-buttons, dimmers, roller blind controls 7746 01 + 7746 41 7740 02 + 7740 41 7740 96 + 7740 41 7740 13 + 7740 41 7740 62 + 7740 41 Mechanisms supplied with Ivory or White cover plates, to
More informationSimply Stylish Wiring Accessories
www.scolmore.com 402 402 402 404 Simply Stylish Wiring Accessories Seera has been designed to provide a competitive, cost effective equivalent range of white moulded accessories with a sleek, slim design
More informationA premium range of bright white accessories
A premium range of bright white accessories Switches Sockets Connection Units Fan Isolation Switches Blank Plates Cooker Control Panels Telephone and Data Outlets Coaxial and Satellite Outlets A premium
More informationNiloé. Getting it just right
Niloé Getting it just right Just right... for the environment and for you Eco design laser marking reduction packaging optimization packaging and dust protection recycled materials the Niloé range is manufactured
More informationECO 60 RANGE INTERNATIONAL DOMESTIC RANGE
INTERNATIONAL DOMESTIC RANGE CONTROL DEVICES COMMAND - WHITE CIRCUIT BREAKERS- 250V~ Code Description Type Symbol Pack GW 34 001 1P - 10AX General - 25/100 GW 34 002 1P - 10AX illuminable Functional indicator
More informationStylish Electrical Essentials
Stylish Electrical Essentials Antimicrobial Certified Products The Modern Domestic Wiring Solution All white moulded and Mode Part M wiring accessories are manufactured using Urea Formaldehyde, which has
More informationNiloéTM. Another timeless classic from Legrand now even easier to install. THE GLOBAL SPECIALIST IN ELECTRICAL AND DIGITAL BUILDING INFRASTRUCTURES
NiloéTM Another timeless classic from Legrand now even easier to install. THE GLOBAL SPECIALIST IN ELECTRICAL AND DIGITAL BUILDING INFRASTRUCTURES THE NILOÉ RANGE IS CHANGING And it s even easier to install!
More informationErgonomic electrical accessories
Ergonomic electrical accessories Switches Sockets Connection Units Fan Isolation Switches Blank Plates Cooker Control Panels Telephone and Data Outlets Coaxial and Satellite Outlets contents Switches Sockets
More informationalena switc es Switches 10 AX VA - IP 44 Mechanisms supplied with cover plates, to be equipped with plates (p ) Screw or claw mounting
alena switc es 7 701 01 + 7 701 51 7 744 10 + 7 744 51 (p. 498-499) Screw or claw mounting Pack Cat.Nos Switches 10 AX - 250 VA One-way switch 10 7 743 01 Ivory 10 7 744 01 White 10 7 701 01 Brilliant
More informationProduct and functional description
Product and functional description The UP 525/13 Universal Dimmer is a KNX device with one dimmer output. The device is installed in a flushmount wall box (60 mm Ø, depth 60 mm) or an installation box.
More informationPanasonic top level series with super panel and vigorous outlines bringing elegance to your everyday life. BS-TYPE
Panasonic top level series with super panel and vigorous outlines bringing elegance to your everyday life. 8 SURFACE ART AND SUPER-SLIM DESIGN Perfect asymmetric design along with high quality aluminum
More informationPlexo IP 55/IP 66 Makes your day, rain or shine
Plexo IP 55/IP 66 Makes your day, rain or shine PLEXO / WEATHERPROOF WIRING DEVICES www.legrand.com.sg Plexo IP 55 Ingenious features for easy installation >> Time saving guaranteed: no cut-out Uncut pierceable
More informationProduct and functional description
Product and functional description The RS 525/23 Universal Dimmer is a KNX device with one dimmer output. The device is installed in an AP 118 Control Module Box or an AP 641 Room Control Box. The bus
More informationProduct and functional description
Product and functional description Connection example The universal dimmer main module N 528/31 is an installation device for DIN-rail mounting, with N-system dimensions. It is designed for lighting control,
More informationAttraction in simplicity. Kalo.
Attraction in simplicity. Kalo www.fengshengelectric.com.sg 2 Attraction in simplicity. Attraction in simplicity. 3 Attraction in simplicity. 4 Attraction in simplicity. Intelligently designed with simplicity
More informationProduct and Applications Description. Application Programs. Note. instabus EIB Technical Product Information. June 2005
Product and Applications Description Application Programs The application programs of the dimmer UP 525/01 consist of two elements: the actuating and the sensor program element. The tasks actuating program
More informationVimark Curve Vimark Evo
Vimark Curve Vimark Evo Vimark Heritage Steeped in over 20 years of history and synonymous with quality, reliability and value, Deta Vimark has carved out an enviable market leading position and remains
More informationTrade Product Catalogue 2018/2019. Trade CELEBRATING YEARS OF. Product Catalogue 2018/
Trade Product Catalogue 2018/2019 Trade Product Catalogue 2018/2019 CELEBRATING 1958-2018 YEARS OF A time to celebrate This year Deta Electrical has every reason to celebrate as the company reaches its
More informationADVANCED SWITCHING TECHNOLOGY Miniature switch for a lighter and more comfortable touch. H A R M O N Y HIGHLY RELIABLE SAFETY FEATURES.
Simple and screw less design easy to blend with any of your personal interior ideas. A INSPIRING BLEND OF CREATIVITY Panasonic original design base for world wide wiring devices development. Trendy color
More informationMallia. Express Yourself Like Never Before
TM Mallia Express Yourself Like Never Before SPOILT FOR CH ICE Mixing colours is a breeze with Mallia TM. With new rocker colours added to the range, there are now even more exciting possibilities. 2 WOW
More informationNexus Flatplate. Nexus Flatplate Wiring Accessories. Slimline screwless and screwed accessories available in a range of decorative metal finishes
57 Wiring Accessories Slimline screwless and screwed accessories available in a range of decorative metal finishes Features & Finishes No visible plastic around switches Sleek flat profile Screwless front
More informationA INSPIRING BLEND OF CREATIVITY ADVANCED SWITCHING TECHNOLOGY HIGHLY RELIABLE SAFETY FEATURES. Series
Simple and screw less design easy to blend with any of your personal interior ideas. A INSPIRING BLEND OF CREATIVITY Panasonic original design base for world wide wiring devices development. Trendy color
More informationAll two-way switches with indicator have a terminal for neutral connection and have to be equipped with an indicator
Programme switches, pull-cord switches and ventilation control 0 792 01 0 792 11 0 770 02 0 792 12 0 770 14 0 770 27 All two-way switches with indicator have a terminal for neutral connection and have
More informationWeathersafe Vision. Installation & Operating Instructions
Weathersafe Vision Installation & Operating Instructions IP66 Products covered by these instructions 1 TGVL01 TGVL02 TGVL03 TGVL05 TGV101N TGV201N TGV104N Single Gang 2-Way Switch [SP] 10AX (Fluorescent
More informationProduct and functional description
Product and functional description Connection example The universal dimmer submodule N 528/41 is an installation device for DIN-rail mounting, with N-system dimensions. It is designed for lighting control,
More informationNexus Flatplate. Nexus Flatplate Wiring Accessories. Slimline screwless and screwed accessories available in a range of decorative metal finishes
57 Wiring Accessories Slimline screwless and screwed accessories available in a range of decorative metal finishes Features & Finishes No visible plastic around switches Sleek flat profile Switches & Sockets
More informationNice and solid. Merten M-Smart
Nice and solid Merten M-Smart The ideal choice linear forms and discreet radiance Merten M-Smart Merten M-Smart - a switch series that is worthy of its name. An ingenious combination of straightforward,
More informationMylinc mechanisms switches and accessories Mylinc mechanisms dimmers and fan regulators 6755 01 6755 03 6755 95 6755 35 6755 30 6755 31 6755 40 6755 26 6755 97 6759 75 6759 69 Switches are ISI marked as
More informationProduct and Applications Description. Example of Operation. Installation Instructions WARNING. Note. Application Programs
Product and Applications Description Example of Operation dimmer UP 525/11 load circuit AC 230 V L1 N The dimmer UP 525/11 is a dimming actuator for mounting in box mounts (a.o. 60 mm Ø, 60 mm depth).
More informationBS 287 DUAL CHANNEL POWER SUPPLY. User Manual. January 2017 V1.0
BS 287 DUAL CHANNEL POWER SUPPLY User Manual January 2017 V1.0 Table of contents 1.0 SAFETY INSTRUCTIONS... 3 2.0 GENERAL DESCRIPTION PS 289... 4 3.0 MECHANICAL INSTALLATION... 5 4.0 MAINS POWER & SAFETY
More informationLASERMET SLIMJIM LED SIGN INSTRUCTION MANUAL LEDS-SJ XXX
LASERMET SLIMJIM LED SIGN INSTRUCTION MANUAL LEDS-SJ 00843-00-XXX 00843-53-000 Page 1 of 11 Issue 3 2 January 2013 Lasermet SlimJim Illuminated Sign Instruction Manual Contents Introduction... 4 Installation...
More informationTechnical Data. Wi-Fi Socket Range Extender. Features: 922WR
Technical Data Wi-Fi Socket Range Extender Brief product description: Eliminate dead spots and expand your Wi-Fi coverage with the Wi-Fi Socket Range Extender. Features: Improved Wi-Fi coverage throughout
More informationT E C H N I C A L C A T A L O G U E
TECHNICAL CATALOGUE Paint Guard Revolutionary technology As per SASO standards Thin paint guard film protects products from dust and paint stains. Freedom of choice The terminals are constructed as single
More informationProduct and functional description
Product and functional description The instabus / DAI gateway 141 is a KX EIB device with one DAI output to which up to 64 DAI actuators (e.g. DAI ballasts) can be connected to. It is not allowed to connect
More informationWide range of items for multi-design coordinations. BS -TYPE
BS-TYPE Wide range of items for multi-design coordinations. BS -TYPE 02 INDEX page 06 / 07 Switches page 07 / 08 Socket Outlets page 09 / 10 Accessories page 10 Dimmer Switches page 11 Others 03 TECHNICAL
More informationBS 181 SINGLE CHANNEL POWER SUPPLY USER MANUAL
BS 181 SINGLE CHANNEL POWER SUPPLY USER MANUAL August 2016 This product is designed and manufactured by: ASL Intercom B.V. Zonnebaan 42 3542 EG Utrecht The Netherlands Phone: +31 (0)30 2411901 Fax: +31
More informationElectrical Demand Specification (Reference SOP: )
Project: Equipment Description: Location: Equipment No.: Project No: Protocol No.: Content Index 1. GENERAL...3 Design Standards...3 1.1. Standards...3 2. DESIGN...3 2.1. Safety...3 2.2. Circuit protection...3
More information2x 10W LED Slimline PIR Floodlight Twin Flood
2x 10W LED Slimline PIR Floodlight Twin Flood Model: LED200PIRBE Black Model: LED200PIRWHE White Installation & Operating Instructions 1 1. General Information These instructions should be read carefully
More informationMayfair. Make The Switch
Mayfair Make The Switch Mayfair Mayfair Wiring Accessories A range of slim profile, durable screwless wiring accessories offering a stylish solution for the home, hotel and office applications n Extensive
More informationHIGHLY RELIABLE SAFETY FEATURES. Sharp design fitting beautifully with residential atmosphere as well as business environment.
Sharp design fitting beautifully with residential atmosphere as well as business environment. MAKES A STATEMENT IN STYLE Modern and squared plate bringing a fresher taste to your interior with a wide range
More informationMyrius TM mechanisms - white
6730 00 6730 02 6730 06 6730 09 6730 13 6730 15 6730 16 Switches - 6 A - 230 VA 6730 00 6 A switch 1 W - 140 20/200 6730 01 6 A switch 2 W - 186 20/200 6730 02 6 A switch 1 W - 174 20/200 with indicator
More informationOperating instructions. Switching amplifier DN0210 DN / / 2015
Operating instructions Switching amplifier DN0210 DN0220 UK 80011079 / 00 01 / 2015 Contents 1 Preliminary note...4 1.1 Symbols used...4 1.2 Warning signs used...4 2 Safety instructions...5 2.1 General...5
More information2400W PIR Light Controller
2400W PIR Light Controller Model: SLW2400 White Installation & Operating Instructions 1 1. General Information These instructions should be read carefully and retained for further reference and maintenance.
More informationProduct and functional description
Product and functional description The RS 520/23 shutter / blind actuator is a KNX device with one relay output. The device is installed in an AP 118 Control Module Box or an AP 641 Room Control Box. The
More informationProduct and functional description. Application Program. instabus EIB Technical product information. April (6 x AC 230 V / 0,05 A)
Product and functional description also functions if the bus cable is not connected or if the bus communication fails. After a long push button action (> 2 s), the other valve group is selected. The yellow
More informationFLEX Ex Spring Clamp Terminal Base
Installation Instructions FLEX Ex Spring Clamp Terminal Base (Cat. No. 1797-TB3S) 1 10 11 4 Only remove this cover plug if connecting another terminal base unit. 3 5 6 12 2 7 8 9 41253 Component Identification
More informationIMPORTANT NOTES HOW TO USE THIS CATALOG PRODUCT SAFETY WARRANTY. This catalog details the general specification for your Carrot Products.
1 IMPORTANT NOTES HOW TO USE THIS CATALOG This catalog details the general specification for your Carrot Products. PRODUCT SAFETY All Carrot RF, Electronic Switches comply with EN/IEC60669-2-1. All Carrot
More information5 imple reasons to switch
5 imple reasons to switch BELANKO TM / NEW RANGE OF WIRING DEVICES 5imple reasons to switch to belanko tm With Belanko TM, simplicity is beauty. Now, discover 5 good reasons why Belanko TM should be your
More informationELECTRICAL ACCESSORIES - E SERIES
50 E Series is an exclusive range of modern wiring accessories offering innovative design combined with the exceptional strength of polycarbonate making it the first choice for installation in a wide variety
More information1.2 Section ADAPTORS AND MULTI-OUTLET SOCKETS. Research. BLUELINE Series AZZURRA Series SICURA Series. To give you the best...always!
ADAPTORS AND Research To give you the best...always! BLUELINE Series AZZURRA Series SICURA Series 32 33 ADAPTORS REFERENCE STANDARDS CEI 23-50 for domestic and similar applications Part 1: General requirements
More informationSafety. Features 1 ID: Make all the connections before you plug in the main power. DMX512 Controllable and RDM Configurable
Features DMX512 Controllable and RDM Configurable Designed for driving LED strips through 6 high power 12 and 24 Volts output units available Easy addressing interface (physical switches and RDM) Isolated
More informationWiring Accessories. low voltage. Wiring Accessories
About CBI-electric: CBI-electric: is a South African company with more than half a century of experience in the design and manufacture of a comprehensive range of technically advanced products for electrical
More informationC-Bus Four Channel Voltage Free Relay Installation Instructions
C-Bus Four Channel Voltage Free Relay Installation Instructions 5504RVF Series REGISTERED DESIGN REGISTERED PATENT Table of Contents Section... Page 1.0 Product Range...3 2.0 Description...3 3.0 Capabilities...3
More informationCOMPACT LED DRIVERS. PrimeLine DALI dimmable & Selectable Current (Dip Switch) PrimeLine DALI DIMMABLE & SELECTABLE CURRENT (DIP SWITCH)
COMPACT LED DRIVERS PrimeLine DALI DIMMABLE & SELECTABLE CURRENT (DIP SWITCH) 186762, 186763 Typical Applications Built-in in compact luminaires Shop lighting Downlights PrimeLine DALI dimmable & Selectable
More informationGFCI (RCD) RECEPTACLES AND PLUGS 2 Pole 3 Wire Grounding
GFCI (RCD) RECEPTACLES AND PLUGS 2 Pole 3 Wire Grounding AU1-10R AU1-10P FR1-R EU1-P Cat. No. Drawing Configuration Australian GFCI (RCD) angle plug. trip. 10 ampere 230 volt, 50 Hz. 20 watt maximum. Test
More informationCONTROL PANEL WIRING SPECIFICATIONS
CONTROL PANEL WIRING ISSUE STATUS FIRST REV DESCRIPTION DATE 001 1 ST ISSUE 22/04/2014 002 1 ST AMMENDMENT 10/03/2017 003 2 ND AMMENDMENT 08/09/2017 THIS DOCUMENT IS DESIGNED TO COVER ALL APPLICATIONS,
More informationCompact Module. Category 6 UTP Cabling System
Compact Module Suitable for Gigabit Ethernet applications Shallow design requires minimal back-box depth Interchangeable with all other Euro modules and quarter blanks Fits all standard Euro faceplates
More informationfor a perfect electrical installation. The range of rail-mounted terminal blocks
The range of rail-mounted terminal blocks for a perfect electrical installation. The range of rail-mounted terminal blocks for a perfect electrical installation. The new standard for rail-mounted terminal
More informationSolid as a rock Soliroc
Solid as a rock Soliroc SOLUTIONS FOR EXPOSED OR UNSUPERVISED ENVIRONMENTS Think Soliroc for strength and design in exposed areas at the mercy of vandals and other abuse. The IK 10 Soliroc TM guarantees
More informationRCD Fused Connection Unit Model: RCD10WPV. RCD Double Sockets Models: RCD05WAV, RCD06WPV, RCD07MAV, RCD08MPV. Installation & Operating Instructions
RCD Fused Connection Unit Model: RCD10WPV RCD Double Sockets Models: RCD05WAV, RCD06WPV, RCD07MAV, RCD08MPV Installation & Operating Instructions General The Timeguard range of RCDs provides protection
More informationTHIS PAGE LEFT BLANK
SOUND LEVEL LIMITER THIS PAGE LEFT BLANK IMPORTANT Installer and Users please note: These instructions should be read carefully and left with the user of the product for future reference. The must be installed
More informationControl Your World. Lighting Control System
Lighting Control System Control Your World Today s homes have a wide variety of lights, dimmers and switches, indoors and out. Lighting control provides convenience, cost savings and an extra measure of
More informationSmart Touch Thermostat Colour Touchscreen Thermostat
OBSMART Smart Touch Thermostat Colour Touchscreen Thermostat INTRODUCTION Orbry Smart Touch Thermostat The Orbry Smart Touch Thermostat is a digital thermostat, which is designed for electric underfloor
More informationMetal Clad Wiring Accessories. A rugged scratch resistant metal, suitable for everyday use in commercial and industrial environments
Metal Clad Wiring Accessories A rugged scratch resistant metal, suitable for everyday use in commercial and industrial environments 85 Features No visible plastic around switches Supplied with multiple
More informationProduct and Applications Description. Note. Example of Operation. Installation Instructions. Application Programs WARNING
Product and Applications Description Note If the application program is not loaded completely by the ETS, you had better interrupt the 24 V voltage supply of the I/O-module during the loading interval.
More informationMC 11 EB-2 Power supply cabinet with external bus, AC version
MC 11 EB-2 Power supply cabinet with external bus, AC version USER/MAINTENANCE MANUAL 1 SLOT 0 SLOT 1 SLOT 2 SLOT 3 SLOT 4 SLOT 5 SLOT 6 SLOT 7 SLOT 8 SLOT 9 SLOT 10 SLOT 11 EB-2 (a) MC11 (b) (c) Figures
More informationMureva Assembly surface mounted wiring devices
Assembly surface Switches P124543 P124547 External dimensions : 72 x 72 x 47 mm.. Assembly surface rockers become illuminated using bulbs and indicators in option. They can carry a label using the legended
More informationProduct Catalogue concept bs Switches and Sockets series
Product Catalogue concept bs Switches and Sockets series 1SXF-610007C0201 01-2009 ABB Group ABB (www.abb.com) is a leader in power and automation technologies that enable utility and industry customers
More informationThe right solution for every home
Domae Household switchboards The right solution for every home Household guide 2002 Building a New Electric World. Household switchboards Domae The right solution for every home Household guide 2002 Building
More informationArteor TM Radio/ZigBee
Arteor TM Radio/ZigBee n Switches and dimmers maximum loads at 230 V For values at 0 V, please halve values Leading edge Trailing edge Cat.Nos. Incandescent lamp Halogen lamp ELV halogen with ferromagnetic
More informationInstallation Instructions
Installation Instructions (Cat. No. 1794-TBN) 6 1 5 9 4 2 3 10 6 7 8 Component Identification 1 Female flexbus connector 2 Terminal base unit (1794-TBN) 3 Male flexbus connector 4 Keyswitch Set to the
More information