Smart Touch Thermostat Colour Touchscreen Thermostat
|
|
- Terence Hill
- 5 years ago
- Views:
Transcription
1 OBSMART Smart Touch Thermostat Colour Touchscreen Thermostat
2 INTRODUCTION Orbry Smart Touch Thermostat The Orbry Smart Touch Thermostat is a digital thermostat, which is designed for electric underfloor heating systems with a maximum load of up to 16A (3600W). The Orbry Smart Touch features a 4.3 colour touchscreen display and four (4) languages. IMPORTANT SAFETY REGULATIONS ALL WIRING MUST CONFORM TO IEE 17TH EDITION PART P REGULATIONS. THIS PRODUCT IS RATED IP30. The Orbry Smart Touch Thermostat is IP30 rated and suitable for safe installation in bathrooms. It is not suitable for use in special locations, such as wet zones. All electrical circuits in bathrooms must be protected by a 30mA RCD. The instructions we supply include as much information as possible to ensure that all installations comply with current electrical regulations. Please call our customer support line, if in any doubt, on DO Install a conduit for your sensor probe before thermostat installation. DO NOT Ignore electrical regulations. Install this thermostat in a wet zone.
3 INSTALLING THE ORBRY SMART TOUCH Before you begin The sensor conduit and deep back box must be fi tted before installation of the actual thermostat can begin. Feed the sensor probe provided down through the sensor conduit into a representive area of the floor. For technical advice or help with any queries, please call our customer support team on or visit Installation Step 1: Release the face plate Place the unit face down on a hard surface and push the three (3) clips located on the bottom of the Orbry Smart Touch in with a screwdriver to release the face plate. Step 2: Disconnect ribbon cable & remove face plate Once the face plate has been gently opened disconnect the ribbon cable to release the face plate.
4 WIRING THE ORBRY SMART TOUCH Wire and replace the face plate Loosen the tension screws to allow the wires to be inserted and fixed. Position the cables as shown in the wiring diagram and ensure each screw is tightened correctly Sensor L 3600W/16A 230V/AC Ensure system is correctly earthed. N N L Fix the Orbry Smart Touch Thermostat to the wall Align the Orbry Smart Touch with your back box and fix in place with the screws provided. Now, reconnect the ribbon connections and reseat the face plate (bottom edge first). Ensure the Orbry Smart Touch is securely fixed before continuing Faceplate 4. Back plate 2. Provided screws 5. Back box 3. Ribbon connectors
5 PROGRAMMING THE ORBRY SMART TOUCH Orbry Smart Touch Thermostat Interface ROOM On / Off button 8. Heating icon 2. Mode button 9. Weekday icon 3. Menu button 10. Ambient temperature 4. Down button 11. Clock icon 5. Up button 12. Temperature icon 6. Mode icon 7. Set temperature 13. Floor temperature 14. Mode icon area
6 PROGRAMMING THE ORBRY SMART TOUCH Preset Modes Manually switch between these preset temperature modes to allow flexibility outside of your heating schedule. Settings Economy mode Preset a low energy saving temperature 18 C for economical comfort and energy savings. Comfort mode Preset a comfort temperature (e.g. 25 C) and enjoy warmth outside of your heating schedule. Program mode Your own customisable heating schedule. Holiday mode Automatically maintain a preset low energy saving temperature (e.g. 8 C) while you re away. Boost mode Set a high temperature (e.g. 27 C) and quickly switch to this high temperature on demand. Language selection Press to choose one of four (4) languages. Preset temperatures Use to define pre-set temperatures. Program review Use to check your day schedule. Date & time button Use to set the correct weekday and time. Protection temperatures Use to define minimum and maximum temperatures.
7 PROGRAMMING THE ORBRY SMART TOUCH Schedule settings Press the MENU Button, then press to review your weekly schedule. Select Mon Fri, Sat or Sun to edit your custom heating schedule. Example: If you would like to edit your Sunday schedule, then press the Sun column to enter the edit page (as shown). Every setting can be edited using the or buttons. RETURN RETURN In the Sun column, there are six (6) periods. You can press the or buttons to choose the period you are going to change. The button will display beside the period selected. Next, you can set the start time and desired temperature by pressing the and buttons. 3. Finally, press APPLY to save your new schedule.
8 PROGRAMMING THE ORBRY SMART TOUCH Edit date & time Press the MENU button, then the button to edit the date and time with the and buttons. Press APPLY to save the changes. RETURN Preset temperature mode Press the MENU button, then the button to select a mode. Now, edit that mode setting s temperature using the and buttons. Press APPLY to save the changes. Language select Press the MENU button, then the button to enter the language page. Choose the desired language and press APPLY to save the changes. RETURN RETURN
9 PROGRAMMING THE ORBRY SMART TOUCH Protection settings Press the MENU then the button to enter the protection settings page. You can set an over protection temperature and a low protection temperature using the and buttons. Press APPLY to save the changes. RETURN High protection: This is an over heat protection setting designed to monitor the floor temperature and set a limit defined by you. If the system reaches the set protection temperature, the system will shut off automatically. Low protection: This is a frost protection mode designed to function when the Orbry Smart Touch is switched off. If the ambient temperature reaches the set protection temperature, the system will automatically switch on to maintain a minimum temperature. Please note: The upper limit should be no higher than 28 C to conform with European regulations.
10 PROGRAMMING THE ORBRY SMART TOUCH Parameter settings To access the parameter settings, switch the Orbry Smart Touch OFF and immediately press the button for two (2) seconds. You can set the desired values by pressing << OR >>. Go to the other pages by pressing PRE or NEXT. The upper limit should not exceed 28 C. Menu Description Range 01 Temperature Offset -8 C ~ 8 C 02 Dead Zone 0 C ~ 3 C 03 Set Point Maximum 5 C ~ 35 C 04 Set Point Minimum 5 C ~ 35 C 05 NTC Select (Ambient I, Floor E) I only, E only, I & E, I or E 06 Low Protection Maximum 5 C ~ 10 C 07 Low Protection Minimum 5 C ~ 10 C 08 High Protection Maximum 5 C ~ 90 C 09 High Protection Minimum 5 C ~ 90 C 10 Backlight off Time after Operation 3s ~ 180s 11 Min. Backlight Brightness of Standby Status 1% ~ 100% 12 Relay Delay Time 0s ~ 250s 13 Relay Output Normal (NO); Inverted (NC) 14 Restore << or >>
11 Sensor TECHNICAL SPECIFICATIONS Dimensions 60mm 19mm 31mm L N 3600W/16A N 230V/AC L 50mm 52mm 94mm mm 130mm
12 Product features 4.3 inch colour touchscreen display Control electric underfloor heating systems up to 16A (3600W) Adjustable comfort mode, economy mode, boost mode, holiday mode, and program mode control days, 6 event programmable schedule Ambient and/or floor sensors Four languages: English, French, German, and Dutch Clock and date display Temperature calibration Overheat and frost protection modes Single gang extra deep back box Voltage Maximum load Temperature range Ambient Sensor Accuracy Warranty IP Rating Width Height Depth 230V 50/60Hz 16A (3600W) 5 ~ 35 O C 0 ~ 50 O C NTC 10k 10kΩ at 25 O C ± 0.5 O C 3 years IP30 130mm 87mm 50mm (31mm in wall) info@orbry.com
Italian, Japanese, French, Poland, simplified Chinese, traditional Chinese, Holland, Portuguese, Vietnamese, Arabic, Korean)
General HTW-WF06 series Wifi thermostat is widely used in these environment like Homes, Residential buildings, Schools, Hotels, Hospitals, Offices and etc. to main an ideal room temperature purpose. It
More informationModel: Available in : Sapphire Black and Glacier White
Model: Available in : Sapphire Black and Glacier White 1 Table of Contents Product Image 1 Locking/Unlocking the SmartStat 20 Table of Contents 2 Standby/Away Mode 21 What is a Programmable Room Thermostat?
More informationModel: Available in : Sapphire Black and Glacier White
1 Model: Available in : Sapphire Black and Glacier White 1 Table of Contents Product Image 1 Locking/Unlocking the SmartStat 20 23 Table of Contents 2 Standby/Away Mode Mode 21 24 What is a Programmable
More informationRAMSES D GB F NL. Installation and operating instructions Room thermostat. RAMSES 832 top2
309 358 04 RAMSES RAMSES 811 top2 RAMSES 831 top2 811 9 132 831 9 132 RAMSES 812 top2 RAMSES 832 top2 812 0 132 832 0 132 GB Installation and operating instructions Room thermostat D GB F E I NL RAMSES
More informationOperating instructions for RAMSES 811 top2_812 top2 and RAMSES 831 top2_832 top2
Operating instructions for RAMSES 811 top2_812 top2 and RAMSES 831 top2_832 top2 Dear client, if you have the newer device, please use page 1 to 33 RAMSES RAMSES 811 top2 RAMSES 831 top2 8119132 8319132
More informationPT712-EI FOR FLOOR HEATING DIGITAL THERMOSTAT
DIGITAL THERMOSTAT PT712-EI FOR FLOOR HEATING including external sensor backup in case of voltage failure > 100 hours direct installation on junction box well-arranged backlit display VENUS switch design
More informationDigital Room Thermostat for Underfloor Heating Applications
ERT50 230v Digital Room Thermostat for Underfloor Heating Applications Instruction Manual Model No ERT50 230v PRODUCT COMPLIANCE This product complies with the essential requirements of the following EC
More informationModel: Touchpad (TFT) Model: TFT
Model: Touchpad (TFT) Model: TFT 1 Model: Touchpad TFT Table of Contents Set-Up Product Image Table of Contents Installation Procedure Initial Setup Setting the Clock LCD Display My System Locking the
More informationERT50T Triac Noiseless Digital Room Thermostat for Underfloor Heating Applications
ERT50T Triac Noiseless Digital Room Thermostat for Underfloor Heating Applications Instruction Manual Model No ERT50T Triac 2 PRODUCT COMPLIANCE This product complies with the essential requirements of
More informationQuick Start Installation and User Manual
1 Quick Start Installation and User Manual Contents 1. Overview 2. Technical Specifications 3. Installation Mounting Electrical Installation Clamp Installation Wiring Diagrams 4. Installation Settings
More informationGlass sensors 35. Supplementary products 39
Understatement is an art, and the makes it perfect. Up to eight functions are concealed under a pure surface that is practically flush with the wall, and can be custom-labelled on request. A single touch
More information7-day room temperature controller
s 2 208 7-day room temperature controller Heating applications REV34.. Mains-independent, battery-operated room temperature controller featuring user-friendly operation, easy-to-read display and large
More informationRVL470. Heating controller. G2522en. Installation Instructions. 1 Installation. 2 Commissioning Wall mounting DIN rail mounting
G2522en Heating controller Installation Instructions RVL470 1 Installation 1.1 Place of installation In a dry room, e.g. the boiler room Mounting choices: In a control panel (on the inner wall or on a
More informationSmart heating system. with wireless thermostats & smartphone control for every room. Get the most out of any water based underfloor heating
Smart heating system with wireless thermostats & smartphone control for every room Get the most out of any water based underfloor heating DETAILED OVERVIEW Control the heating in your home from anywhere.
More informationMiG2 CONTROLLERS. 2 & 4 Stage General Purpose Controllers, with Air-conditioning Facilities
MiG2 CONTROLLERS 2 & 4 Stage General Purpose Controllers, with Air-conditioning Facilities The MiG2 controllers incorporate: 2 Inputs (Configurable as Resistive, 0 10V, 0 20mA or 4 20mA) 2 or 4 Relay Outputs
More informationMaster room unit for RRV controllers
2 722 Master room unit for RRV controllers 2 wire bus connection QAX850 Multifunctional, digital room unit for installer and end-user interface with RRV controllers. Use Use Application Room unit in combination
More informationRoom Temperature Controller
3 023 Room Temperature Controller for four-pipe fan coil units RCC30 Outputs for on / off valve actuators Outputs for three-speed fan Control depending on room or return air temperature Operating modes:
More informationInstallation Guide DEVIlink CC Central Controller
DEVIlink CC Central Controller www.devi.com Table of Contents 1 Introduction.................................... 4 2 Guidelines for installation....................... 5 3 Installation plan.................................
More informationOEM. Room unit QAA822 with2- wire interface. Building Technologies CLIMATIX TM. For use with Climatix controllers
OEM CLIMATIX TM Room unit QAA822 with2- wire interface For use with Climatix controllers Remote control of air conditioning unit Mandík Measurement of the room temperature Buttons for starting, setting
More informationSemi flush-mounted room temperature controllers with LCD
s 3 077 RDD310 RDE410 Semi flush-mounted room temperature controllers with LCD For heating systems RDD310 RDE410 RDD310 and RDE410 features: Operating voltage AC 230 V 2-position control with On / Off
More informationProgrammable(5+1+1)Touch Screen LCD Wired Thermostat. General. Features. Operating Algorithm
Programmable(5+1+1)Touch Screen LCD Wired Thermoat General Front View Back View HTW-91-410 series ermoat is widely used in ese environment like Homes, Residential buildings, Schools, Offices and etc. to
More informationSOLARIMMERSION IV Advanced Installation Manual v1.9
SOLARIMMERSION IV Advanced Installation Manual v1.9 1 Contents 1. Overview 2. Technical Specifications 3. Installation Mounting Electrical Installation Clamp Installation Wiring Diagrams 4. Installation
More informationSemi flush-mounted room temperature controllers with LCD
s 3 077 RDD310 RDE410 Semi flush-mounted room temperature controllers with LCD For heating systems RDD310 RDE410 RDD310 and RDE410 features: Operating voltage AC 230 V 2-position control with On / Off
More informationWeekday / weekend room temperature controller
s 2 203 Weekday / weekend room temperature controller Heating applications REV17.. Mains-independent, battery-operated room temperature controller featuring user-friendly operation, easy-to-read display
More informationFree Energy Band RCC30U Room Temperature Controller for Four-pipe Fan Coil Unit
Document No. 155-324 Free Energy Band RCC30U Room Temperature Controller for Four-pipe Fan Coil Unit Description Features Application Product Number Room temperature controller for four-pipe fan coil units.
More informationModel: TM-1 / TM1-N. 1 Time Clock Series
Model: TM-1 / TM1-N Model: TM-1 / TM1-N 1 Time Clock Series Table of Contents Product Image Table of Contents Installation Procedure LCD Display Operating Modes Setting the Operating Mode Setting the Clock
More informationOrbital smart Tunable Downlight
Commissioning The ceiling surface must be flat and smooth to ensure a good fit. Push the spring clips upwards and fit into the ceiling hole. See Fig 1. Push the unit up until firmly in position, ensuring
More informationRoom Temperature Controllers
3 021 Room Temperature Controllers for two-pipe fan coil units RCC10 Output for on / off valve actuator Outputs for three-speed fan Control depending on the room or return air temperature (RCC10) Automatic
More information7-day room temperature controller
s 2 205 7-day room temperature controller Heating or cooling applications REV24.. Mains-independent, battery-operated room temperature controller featuring user-friendly operation, easy-to-read display
More informationIntegrating and configuring Dynalite lighting and heating systems with SystemNet software
Integrating and configuring Dynalite lighting and heating systems with SystemNet software System Net Configuration Software 10.0 or higher Firmware 10.0 or higher S6 or six port hub only, colour touch
More informationProgrammable(5+1+1)Touch Screen LCD Wireless Thermostat. General. Features. Operating Algorithm
Programmable(5+1+1)Touch Screen LCD Wireless Thermoat General Controlling Panel Receiver HTW-91-WT410 series ermoat is widely used in ese environment like Homes, Residential buildings, Schools, Offices
More informationRCF-230CD. Communicating room thermostat for fan-coil applications with on/off outputs
revision 11 2013 RCF-230CD Communicating room thermostat for fan-coil applications with on/off outputs RCF-230CD intended to control heating and/or cooling in 2- or 4-pipe installations. Setpoint and fan
More informationUC102 basic version with display and knob UC102BL version with display, knob and backlight UC102DK version without knob and display
UC102 Communicative heating controller Summary UC102 is a communicative room heating controller with two inputs and one PWM output for control of a radiator or electrical heater. It can work autonomously,
More informationNiloé. Getting it just right
Niloé Getting it just right Just right... for the environment and for you Eco design laser marking reduction packaging optimization packaging and dust protection recycled materials the Niloé range is manufactured
More informationRCF-230CTD. Room controller for fan-coil applications with outputs for two thermal or one 3-position actuator or function for an electric heater
revision 03 2012 RCF-230CTD Room controller for fan-coil applications with outputs for two thermal or one 3-position actuator or function for an electric heater RCF-230CTD is a room controller intended
More informationSRT-P50 Series Programmable Touchscreen Thermostats
Product sheet TH6.200 Type SRT-P50 SRT-P50 Series Programmable Touchscreen Thermostats The SRT-P50 series programmable thermostats offer a modern flush mounted slim design look for the heating and cooling
More informationRoom Temperature Controller
3 023 Room Temperature Controller for four-pipe fan coil units RCC30 Outputs for on / off valve actuators Outputs for three-speed fan Control depending on room or return air temperature Operating modes:
More informationWeekday / weekend room temperature controller
s 2 203 Weekday / weekend room temperature controller Heating applications REV17.. Mains-independent, battery-operated room temperature controller featuring user-friendly operation, easy-to-read display
More informationKNX temperature control panel
Cat No(s): LN4691KNX H4691KNX CONTENT Page 1. Use...2 2. Description...................................................................................................................... 2 3. Technical
More informationCOMFORT CONTROL CENTER SERVICE INSTRUCTIONS
USA SERVICE OFFICE Dometic Corporation 2320 Industrial Parkway Elkhart, IN 46516 574-294-2511 CANADA Dometic Corporation 46 Zatonski, Unit 3 Brantford, ON N3T 5L8 CANADA 519-720-9578 For Service Center
More informationInstallation Guide. OB-1101 idim Orbit. 1. Features and Connections. Default Settings. Connections MANUAL SWITCH DALI 1 DALI 2 L2 L1
Installation Guide OB-1101 idim Orbit The OB-1101 idim Orbit with single movement detector is a standalone, flush-mounted sensor that provides easy installation and configuration of lighting control applications.
More informationREMOTE CONTROL INSTALLATION & OPERATING INSTRUCTIONS
North American Version REMOTE CONTROL INSTALLATION & OPERATING INSTRUCTIONS Copyright 2009, FPI Fireplace Products International Ltd. All rights reserved. 918-290e 09/22/09 The FireGenie TM Remote Control
More informationModel: EP210. Dual channel programmable controller. Installation Manual
Model: EP210 Dual channel programmable controller Installation Manual Contents Introduction... 3 Product Compliance... 4 Safety Information... 4 Box content... 4 Features... 5 Installation... 5 Button
More informationSelect 107 XLS User Instructions
Select 107 XLS User Instructions A timeswitch allows you to set On and Off time periods. The timeswitch will allow you to set the On and Off time periods for either Hot water or Central heating to suit
More information3% VOLTAGE DROP. Installation Instructions for 100 Watt 24 Volt DC RGB DMX LED Power Supply SAVE THESE INSTRUCTIONS!
Doc # 904-PSB-100W--RGB_06 1718 W. Fullerton Chicago, IL 60614 Ph: 773.770.1195 Fax: 773.935.5613 www.pureedgelighting.com info@pureedgelighting.com 2016 PureEdge Lighting. All Rights Reserved. Installation
More informationRoom Temperature Controller with 7-Day Time Switch, LCD and opt. Remote Temperature Sensor
3 036 Room emperature Controller with 7-Day ime Switch, LCD and opt Remote emperature Sensor for heating systems RDE201 2-position control with ON/OFF output for heating Operating modes: normal operation
More informationRTT2 ROOM TEMPERATURE SWITCH. Mounting and operating instructions
Mounting and operating instructions Table of contents SAFETY AND PRECAUTIONS PRODUCT DESCRIPTION ARTICLE CODES INTENDED AREA OF USE TECHNICAL DATA STANDARDS OPERATIONAL DIAGRAMS WIRING AND CONNECTIONS
More informationVT8600 Series Installation Guide. Rooftop Unit, Heat Pump and Indoor Air Quality Controller
VT8600 Series Installation Guide Rooftop Unit, Heat Pump and Indoor Air Quality Controller 2 Installation Guide VT8600 Series If replacing an existing Room Controller, label wires before removal of Controller.
More information7 Day Programmable Room Thermostat
7 Day Programmable Room Thermostat Model: TRT035N Installation & Operating Instructions 1. General Information These instructions should be read carefully and retained for further reference and maintenance.
More informationElectrical Demand Specification (Reference SOP: )
Project: Equipment Description: Location: Equipment No.: Project No: Protocol No.: Content Index 1. GENERAL...3 Design Standards...3 1.1. Standards...3 2. DESIGN...3 2.1. Safety...3 2.2. Circuit protection...3
More informationFunctions. Technical Data. Wireless Room Thermostat
This surface-mounted radio thermostat has been developed to be able to switch electric and conventional heating systems on and off using a set temperature and time. Functions Large display can be clearly
More information7 Day Digital Programmer 2 Channel Surface Mount
7 Day Digital Programmer 2 Channel Surface Mount Model: TRT036N Installation & Operating Instructions 1. General Information These instructions should be read carefully and retained for further reference
More informationTECHNICAL DATA. V-PIX Quad Bar. Product code CL-VPIX-4-40 Light colour Full spectrum 8 / 480 (see above)
TECHNICAL DATA V-PIX Quad Bar Specification Product Product code CL-VPIX-4-40 Light colour Full spectrum Channels 8 / 480 (see above) Driver Built in Control protocol Art-Net, DMX512, Kling-Net Power and
More informationProMinder Standard Heating System Installation Instructions
IMPORTANT GUIDELINES Please read this instruction leaflet thoroughly before commencing installation. Ensure that that all the electrical installation is carried out by a fully qualified electrician and
More informationS-14 S-14. Compact Digital Multimeter. Compact Digital Multimeter
S-14 Compact Digital Multimeter S-14 Compact Digital Multimeter SAFETY INFORMATION The following safety information must be observed to insure maximum personal safety during the operation at this meter
More informationRCF-230CAD. Communicating room controller for fan-coil applications with two analogue V DC outputs
revision 01 2015 RCF-230CAD Communicating room controller for fan-coil applications with two analogue 0...10 V DC outputs RCF-230CAD intended to control heating and/or cooling in 2- or 4-pipe installations.
More informationMH9-CO2-WA/WD. Introduction. Specification
www.mcohome.com CO2 Monitor MH9-CO2-WA/WD Introduction MCOHome CO2 Monitor is an air quality detector which compatible with Z-Wave Plus technology, it is mainly used to monitor CO2 concentration in industrial,
More informationREDUNDANCY MODULE TSP-REM360 AND TSP-REM600
REDUNDANCY MODULE TSP-REM360 AND TSP-REM600 Operating Instructions Seite 1 Dimensions drawings: TSP-REM360 Weight: 0.882lb Gewicht: 0.40kg Seite 2 Dimensions drawings: TSP-REM600 Bottom view Top view Side
More information7 Day Digital Programmer 1 Channel Surface Mount
7 Day Digital Programmer 1 Channel Surface Mount Model: TRT034N Installation & Operating Instructions 1. General Information These instructions should be read carefully and retained for further reference
More informationDPL4000 Portable Low Range Dew Point Analyzer
OPERATIONS MANUAL DPL4000 Portable Low Range Dew Point Analyzer 7205 Edington Drive / Cincinnati, OH 45249 / Tel (513) 772-0060 / Fax (513) 772-9466 Page #1 of 16 M4581 DPL4000 Product Description: This
More informationclimote HUB Installation Guide
climote HUB Installation Guide Special Instructions 1. Must be fitted by qualified electrician 2. Isolate from mains before commencing installation 3. Delete all customer registration data from installer
More informationProduct documentation
Product documentation Universal push-button module with integrated BCU, 1-gang Universal push-button module with integrated BCU, 2-gang Universal push-button module with integrated BCU, 3-gang Universal
More informationSemi Flush-mount Room Temperature Controllers with LCD
3 076 RDF300, RDF300.02, RDF340 RDF400.01 Semi Flush-mount Room Temperature Controllers with LCD for 2-pipe, 2-pipe with el. heater and 4-pipe fan coil units for use with compressors in DX type equipment
More informationInBin-P Pressure switches from 5 Pa Pa
InBin-P Pressure switches from 5 Pa...100 Pa Electrical, binary pressure or differential pressure switches with adjustable switch activation delay 24 VAC/DC supply voltage, potential free switching contact
More informationON/OFF HUMIDIFIER CONTROL (ROOM 0R DUCT SENSOR) WITH OUTDOOR TEMPERATURE RESET OVERVIEW WALL CONTROLLER INSTALLATION (TCY-BH-T-U)
(ROOM 0R DUCT SENSOR) WITH OUTDOOR TEMPERATURE RESET TCY-BH-T-U Wall controller with sensor TDC-BH-T-U Duct controller with sensor SOA-Tn10 Outdoor temperature sensor (Optional) OVERVIEW For wall applications
More informationVARIA VARIA 826 S WH KNX VARIA 826 S BK KNX D GB F I E NL. Installation and operating instructions Room thermostat VARIA 826 S KNX
307031 VARIA VARIA 826 S WH KNX VARIA 826 S BK KNX 8269210 8269211 GB Installation and operating instructions Room thermostat D GB F I E NL VARIA 826 S KNX Contents Basic safety instructions 3 Display
More informationLASERMET SLIMJIM LED SIGN INSTRUCTION MANUAL LEDS-SJ XXX
LASERMET SLIMJIM LED SIGN INSTRUCTION MANUAL LEDS-SJ 00843-00-XXX 00843-53-000 Page 1 of 11 Issue 3 2 January 2013 Lasermet SlimJim Illuminated Sign Instruction Manual Contents Introduction... 4 Installation...
More informationThe world s smartest heating system. Programmable Touch Screen Thermostat
The world s smartest heating system Programmable Touch Screen Thermostat Visit www.discreteheat.com/thermiser for more information Using the TherMiser TME 3E Instructions on how to set and use your newly
More informationProduct and Function Description
Product and Function Description and the LED display. The touchscreen can be used to select from up to 6 languages for the display of texts and messages. The room temperature controller integrated in Contouch
More informationOperating instructions Evaluation system for flow sensors VS / / 2013
Operating instructions Evaluation system for flow sensors VS3000 7097 / 0 07 / 203 Contents Preliminary note...2 2 Safety instructions...3 3 Function and features... Mounting.... Mounting of the sensors...
More informationTable of Contents. Model: -hw. -hw. Series. Available in : Sapphire Black and Glacier White. Product Image. 16 Table of Contents
-hw -hw 1 Model: -hw Available in : Sapphire Black and Glacier White Table of Contents Product Image 1 Optional features explained 16 Table of Contents 2 Optional settings features table 16 Installation
More informationTemperature controller Ducted systems
2 725 Temperature controller Ducted systems Standard model without zoning functions RRV851 Multifunctional controller used for central control of ducted HVAC systems in combination with a QAX850 master
More informationLCD LCDS LCDRI CONTROLLER OPERATING MANUAL
This manual contains important safety information about installation and use of this equipment. Ignoring this information could result in injuries or damages. It is strictly forbidden to use this equipment
More informationTP5000 Si Range Electronic 5/2 day programmable room thermostat Mains, Battery and RF versions Installation and User Instructions
TP5000 Si Range Electronic 5/2 day programmable room thermostat Mains, Battery and RF versions Certification Mark GB Installation and User Instructions GB Index Index 3-14 Product Specification 3 Installation
More informationPS/IO Circuit Board Retrofit
S&C 6800 Series Automatic Switch Controls PS/IO Circuit Board Retrofit Table of Contents Section Page Introduction Qualified Persons.... 2 Read this Instruction Sheet.... 2 Retain this Instruction Sheet....
More informationCDD4 Series Room CO2 Transmitter Installation Instructions
CDD4 Series Room CO2 Transmitter Installation Instructions Introduction The CO2 transmitter uses Infrared Technology to monitor CO2 levels and outputs a linear 4-20 ma or 0-5/0-10 Vdc signal. Options include
More informationOutput Signal Active Note DC V. Electrical Data Power Supply DC V, ±10%, 1.4 W
Differential Pressure Sensor (Air) Differential pressure transmitter with 8 selectable ranges 0 to 5/10 V, 4 to 20 ma outputs and Modbus functionality. NEMA 4X / IP65 rated enclosure. For monitoring the
More informationOPERATING INSTRUCTION
OPERATING INSTRUCTION AUTORANGING MULTIMETER MAX Ω F C 10A MAX every 15 min. COM V SAFETY INFORMATION The following safety information must be observed to insure maximum personal safety during the operation
More informationCisco CRS 3-Phase AC Power Distribution Unit Installation Guide 2. Cisco CRS 3-Phase AC Power Distribution Unit 2
Cisco CRS 3-Phase AC Power Distribution Unit Installation Guide Cisco CRS 3-Phase AC Power Distribution Unit Installation Guide 2 Cisco CRS 3-Phase AC Power Distribution Unit 2 Revised: November 18, 2016,
More informationRC-CDTO. Pre-programmed room controller with display, communication and three-point control
revision 02 2016 RC-CDTO Pre-programmed room controller with display, communication and three-point control RC-CDTO is a complete pre-programmed room controller from the Regio Midi series intended to control
More informationS-Series Digital Thermostat
Salus ST620 Manual 140x140 Finish:Layout 1 29/4/10 13:11 Page 1 S-Series Digital Thermostat Model No ST620 Instruction Manual Salus ST620 Manual 140x140 Finish:Layout 1 29/4/10 13:11 Page 2 2 Salus ST620
More informationSRT-50 Slimline Touchscreen Thermostats
Product sheet TH6.201 Type SRT-50 SRT-50 Slimline Touchscreen Thermostats The SRT-50 series smart thermostats offer a modern flush mounted slim design look for heating or cooling control. The thermostats
More informationDigital Room Thermostat
Salus RT500 Manual 002:89 23/11/10 11:06 Page 1 Digital Room Thermostat Instruction Manual Model No RT500 2 Salus RT500 Manual 002:89 23/11/10 11:06 Page 2 PRODUCT COMPLIANCE This product complies with
More informationWeathersafe Vision. Installation & Operating Instructions
Weathersafe Vision Installation & Operating Instructions IP66 Products covered by these instructions 1 TGVL01 TGVL02 TGVL03 TGVL05 TGV101N TGV201N TGV104N Single Gang 2-Way Switch [SP] 10AX (Fluorescent
More informationRoom controller STRA-17
Room controller STRA-17 Application example Room 2 Room 3 Room 4 SCADA EXOline alt. RS485 Modbus Transformer STRZ-24 (Required component) STRA-17 is a preprogrammed room controller intended to control
More informationContent. Product Description
EY-modulo 4 EY-RU482F001 Room Operating Unit with Display for Fan Coil applications EY-RU483F001 Room Operating Unit with Display for VAV applications en Guidelines for the electrician Content 1 Product
More informationKM692K KELOX BUS room thermostat - Digital
KM692K KELOX BUS room thermostat - Digital The KELOX BUS system is the intelligent individual room control unit of the future for maximum comfort and energy efficiency for surface temperature control The
More informationIO-AO6X I/O Expansion Module 6 Isolated Analog Outputs
IO-AO6X I/O Expansion Module 6 Isolated Analog Outputs The IO-AO6X is an I/O Expansion Module that can be used in conjunction with specific Unitronics OPLC controllers. The module offers 6 12-bit isolated
More informationModel HM-535 Power Supply Installation and Service Instructions
Model HM-535 Power Supply Installation and Service Instructions 430-535 0104 2004 Heritage MedCall, Inc SENTRY INSTALLATION & SERVICE INSTRUCTIONS POWER SUPPLY UNIT Model HM-535 IMPORTANT SAFETY INSTRUCTIONS
More informationRDF Series Room Temperature Controllers
Document No. 19-49 RDF Series Room Temperature Controllers Product Description Room Temperature Controllers with LCD for twopipe (with and without an electrical heater) and fourpipe fan coil units. Installation
More informationOperating instructions. Switching amplifier DN0210 DN / / 2015
Operating instructions Switching amplifier DN0210 DN0220 UK 80011079 / 00 01 / 2015 Contents 1 Preliminary note...4 1.1 Symbols used...4 1.2 Warning signs used...4 2 Safety instructions...5 2.1 General...5
More informationTemperature Switches
ETS 00 Series Temperature Switch for Inline and Tank Mounting Applications Description The ETS 00 is a compact electronic temperature switch with 4-digit digital display. Pressure resistant to 8700 psi,
More informationOverview - Danfoss Link and Connect software versions
Overview - Danfoss Link and Connect software versions Danfoss Link CC Mk II (with minisd card) software 2.1.35 2.3.27 2.4.51 2.5.57 2.7.42 01-12-2010 The initial Danfoss Link CC software: Supports all
More informationMICROLINE 320/390FB User Manual (English)
MICROLINE 320/390FB User Manual (English) MICROLINE 320/390FB User Manual (English) English Table of Contents Note to Customers... E-2 Important Safety Instructions... E-3 Important Wiring Instructions...
More informationS82S (3/7.5-W Models)
Switch Mode Power Supply (3/7.5-W Models) CSM DS_E_4_3 Miniature DIN Rail Mounting DC-DC Power Supplies 65 mm depth enables mounting onto control panels with 100 mm depth. Inputs: 10.2 to 27.6 VDC (DC
More informationCommunicative heating controller, Ethernet
UC150 Communicative heating controller, Ethernet Summary UC150 is a communicative room heating controller with one PWM output for control of a radiator or electrical heater. It can work autonomously, or
More informationSollatek SVS Range Voltage Stabilisers User Manual
CONTENTS Subject Page(s) Sollatek SVS Range Voltage Stabilisers User Manual SAFETY Safety 2 Main SVS Features 3 SVS Specification 4-5 Unpacking 6 Inspection 6 Installation 6-9 Operation 10-11 Troubleshooting
More informationADVANCED REMOTE CONTROL
ADVANCED REMOTE CONTROL (SUITS IP28) INSTALLATION & OPERATING INSTRUCTIONS 918-962 12/07/10 The Advanced Remote Control is tested safe when installed in accordance with this installation manual. It is
More informationRТTH DUAL ROOM SWITCH
DUAL ROOM SWITCH FOR TEMPERATURE AND RELATIVE HUMIDITY Mounting and operating instructions Table of contents SAFETY AND PRECAUTIONS PRODUCT DESCRIPTION ARTICLE CODES INTENDED AREA OF USE TECHNICAL DATA
More informationTemperature Controller
2 728 Temperature Controller ultizone Floor Heating Systems RRV817 ultizone model with up to 7 zone outputs by combining 2 RRV817 controllers. Used for central control of underfloor heating systems in
More information