*Max split can be split more than once, without exceeding the max single run in each leg.

Transcription

1 INSTALLATIN PCEDUES Please read all instructions prior to installation. Product should be installed by a qualified electrician. Prior to installation, pleast test all tapelight components to ensure no damage has occurred during shipment and layout materials to check bill of material. In hardwire applications, ensure power is off at fuse box to prevent electrical shock. ptimized Light Chart 12 SUPE HIH SIDE EMITTIN SIDE EMITTIN ConTech PWE SUPPLY STANDAD UTPUT HIH UTPUT UTPUT 1 STANDAD UTPUT HIH UTPUT INPUT LTAE: 12 DC 0.7W/FT 1.45W/FT 3.24W/F 3.9W/FT 0.65W/FT 1.4W/FT MDEL N. WATTAE MAX MAX MAX MAX MAX MAX MAX MAX MAX MAX MAX MAX UN SPLIT UN SPLIT UN SPLIT UN SPLIT UN SPLIT UN SPLIT TPL12HW20 20W 14FT 14FT 10FT 10FT 5FT 5FT 5FT 5FT 30FT 30FT 14FT 14FT TLP12P24 24W 17FT 17FT 12FT 12FT 6FT 6FT 5.5FT 5.5FT 32FT 34FT 17FT 17FT TLP12P36 36W 22FT 26FT 17FT 17FT 10FT 10FT 7FT 9FT 32FT 50FT 22FT 26FT TLP12P60 22FT 36FT 17FT 28FT 12FT 16FT 7FT 10FT 32FT 78FT* 22FT 40FT TLP12HW60 22FT 36FT 17FT 28FT 12FT 16FT 7FT 10FT 32FT 78FT* 22FT 40FT TLP12HW FT 36FT 17FT 28FT 12FT 16FT 7FT 10FT 32FT 78FT* 22FT 40FT 1. Is at full power (all three LEDs are illuminated). consumption may vary based on color changing program. *Max split can be split more than once, without exceeding the max single run in each leg. Max un refers to the total single run of tapelight that can go on a power supply. Max Split refers to the total amount of tapelight that can go on a driver if it were separated into two runs. Max un lengths are calculated with 12 DC at the start of the tape run. oltage drop may occur if not using proper wire gauge. Please refer to the Wiring Chart on page one of these instructions. Max un lengths above are calculated with no more than 30% light loss from the start of the tape run to the end of the tape run for optimal light consistency. If run lengths are extended beyond the recommended lengths noted above, there will be inconsistent light output and voltage drop. 24 ConTech PWE SUPPLY STANDAD UTPUT HIH UTPUT W 1 TUNALE WHITE 2 INPUT LTAE: 24 DC 2.1W/FT 3.8W/FT 4.8W/FT 4.3W/FT MAX MAX MAX MAX MAX MAX MAX MAX MDEL N. WATTAE UN SPLIT UN SPLIT UN SPLIT UN SPLIT TLP24HW20 20W 7 FT 9 FT 5 FT 6 FT 4 FT 4 FT 4FT 4FT TLP24P36 36W 11 FT 16 FT 7 FT 9 FT 7 FT 7 FT 8FT 8FT TLP24P60 18 FT 26 FT 12 FT 15 FT 12 FT 12 FT 14FT 14FT TLP24HW60 18 FT 26 FT 12 FT 15 FT 12 FT 12 FT 14FT 14FT TLP24P90 90W 28 FT 40 FT 18 FT 22 FT 14 FT 16 FT 25FT 40FT TLP24HW96 96W 32 FT 45 FT 20 FT 25 FT 16 FT 20 FT 27FT 45FT 1. W is at full power (all four LEDs are illuminated). consumption may vary based on color changing program. 2. Tunable White is at full power (both LEDs are illuminated). consumption may vary based on color temperature combinations. *Max split can be split more than once, without exceeding the max single run in each leg. Max un refers to the total single run of tapelight that can go on a power supply. Max Split refers to the total amount of tapelight that can go on a driver if it were separated into two runs. Max un lengths are calculated with 24 DC at the start of the tape run. oltage drop may occur if not using proper wire gauge. Please refer to the Wiring Chart on page one of these instructions. Max un lengths above are calculated with no more than 30% light loss from the start of the tape run to the end of the tape run for optimal light consistency. If run lengths are extended beyond the recommended lengths noted above, there will be inconsistent light output and voltage drop.

2 INSTALLATIN PCEDUES Please read all instructions prior to installation. Product should be installed by a qualified electrician. Prior to installation, pleast test all tapelight components to ensure no damage has occurred during shipment and layout materials to check bill of material. In hardwire applications, ensure power is off at fuse box to prevent electrical shock. 1 When cutting tapelight, cut only on the cut lines provided. 2 emove adhesive backing, then gently press down the tape onto the surface. Avoid contact with LEDs. NTE: D NT bend or pinch tape on a hard angle. LED Tape Cut Lines 3M acking 3 Add input connector by plugging the input connector into the beginning of the tape. For hardwire applications, an electrician can add any additional wire needed to run back to the power supply. 4For plug-and-play applications, simply plug power supply into a wall outlet. Plug-and-Play Hardwire connector can be field cut Positive to Positive TLCIP12 Connector Negative to Negative

3 INSTALLATIN PCEDUES MUNTIN CHANNEL INSTALLATIN Always wear safety glasses when cutting aluminum channels INSTALLATIN INSTUCTINS 1 2 Cut mounting channel with hacksaw or miter saw with the appropriate blade for cutting aluminum. emove the adhesive backing from the tapelight and place into mounting channel. ently press tapelight down into the channel. Avoid pressure on the LEDs Add to connector 3 4Mark Snap the clear or frosted lens into place. Add end caps to finish off the fixture. Endcaps mounting clip locations. Use screws provided for installation. ecommended max distance between clips is 24". Lens IMPTANT SAFETY INSTUCTINS: ead all the instructions before installation. Save instructions for later use. Turn off power at fuse or circuit breaker box before installation or before doing any maintenance work. Product must be grounded to avoid potential electric shock and any other potential hazards. Product must be mounted in locations and at heights and in a manner consistent with its intended use, and in compliance with National Electrical Code and local codes. Use of accessory equipment is not recommended. Installing contrary to instructions may cause unsafe conditions. Do not block light from the trim aperture, in whole or in part, as this may cause unsafe conditions. Warning: isk of fire. Most dwellings built before 1985 have supply wire rated at 60 C. Consult a qualified electrician before installation. To avoid hazards to children, account for all parts and properly dispose of all packing materials. Call the Technical Support department at ConTech Lighting with any installation questions:

4 To optimize performance, it is recommended to locate the power supply in the middle of your tapelight design. ecommended Layouts 12 High : Two (2) 28' runs with two (2) power supplies, non-dimming 14' 14' 14' 14' 12 High : Two (2) 28' runs with two (2) power supplies, dimming Dimming Module Jumper Wires (y thers) epeater 14' 14' 14' 14' 12 Super High : Four (4) 12' runs with four (4) power supplies, dimming Dimming Module epeater epeater epeater Jumper Wires* Jumper Wires* Jumper Wires* 12' 12' 12' 12' 24 High : ne (1) 36' run with two (2) power supplies, dimming *Jumper wires supplied by others 24 Dimming Module Jumper Wires (y thers) epeater 9' 9' 9' 9' Wiring Chart (Copper Wire) Wire auge Distance* 6 ft. 10 ft. 15 ft. 23 ft. 40 ft. *From driver output to the input connector of the tapelight. 12 auge wire recommended.

5 Dimming Module Wiring Diagram 0-10 Dimming, WHITE LIHT NLY Purple rey LED Dimming Module 0-10 Dimmer (Supplied by thers) epeater Wiring Diagram For Continuous Dimming, WHITE LIHT NLY Signal ptions: 1. connector from previous run of tapelight 2. Secondary dimming signal from output of dimming module Signal LED epeater (TLPPT) Controller Wiring Diagram NLY Controller reen lue Tapelight Wiring Diagram Using a 512 Signal. Converter Provided by thers To Next Decoder For Daisy Chaining Multiple Decoders IN UT Channel lue reen Tapelight

6 Tunable White Controller Wiring Diagram TUNALE WHITE NLY TW Controller W C ray TW Tapelight epeater Wiring Diagram For Extended uns, TUNALE WHITE NLY Signal ptions: 1. connector from previous run of tapelight 2. Secondary control signal from output of Tunable White receiver/controller ray Signal LED epeater (TLPPT) ray TW Tapelight Wiring Diagram Using a 512 Signal, TUNALE WHITE NLY Converter Provided by thers To Next Decoder For Daisy Chaining Multiple Decoders IN UT Channel ray TW Tapelight