-Verify that supply wiring voltage matches power supply voltage by comparing it with power supply label.

Transcription

1 WARNING! RISK OF FIRE OR ELECTRICAL SHOCK Disconnect power before installing or servicing. WARNING: Risk of fire or electrical shock. Luminaire wiring, power supply, or other electrical parts may be damaged when drilling for installation of retrofit assembly hardware. Inspect wiring and components for damage. WARNING: Risk of fire or electric shock. Do not alter, relocate, or remove wiring, lampholders, power supply or any other electrical component if not instructed to. WARNING: Risk of fire or electric shock. Installation of this retrofit assembly requires a person familiar with the construction and operation of the luminaire's electrical system and the hazards involved. If not qualified do not attempt installation. Contact a qualified electrician. WARNING: Risk of fire or electrical shock. Install this kit only in the luminaires that have the construction features and dimensions shown on the drawings. -Only those open holes indicated in the drawings may be made or altered as a result of kit installation. Do not leave any other open holes in an enclosure of wiring or electrical components. -Verify that supply wiring voltage matches power supply voltage by comparing it with power supply label. -Make all electrical and grounded connections in accordance with the National Electric Code (NEC) and any other applicable local code requirements. -THE RETROFIT KIT IS ACCEPTED AS A COMPONENT OF A LUMINAIRE WHERE THE SUITABILITY OF THE COMBINATION SHALL BE DETERMINED BY CSA OR AUTHORITIES HAVING JURISDICTION. -LED RETROFIT LUMINAIRE CONVERSION FOR USE IN ANY FLORESCENT LINEAR LUMINAIRES IN ACCORDANCE WITH THE INSTRUCTIONS PROVIDED WITH THIS RETROFIT KIT. CAUTION: RISK OF INJURY. - Wear gloves and safety glasses at all times when removing luminaire from carton, installing, servicing or performing maintenance. -Allow lamp/luminaire/driver to cool before handling. NOTICE: RISK OF PRODUCT DAMAGE- Failure to follow instructions could result in damage to product and void ALL warranties. -Never connect components under load. -Do NOT mount or support these fixtures in a manner that can cut the outer jacket or damage wire insulation. -Do NOT restrict fixture ventilation. Allow for some volume of airspace around fixture. Avoid covering LED fixtures with insulation, foam, or other material that will prevent convection of conduction cooling. THESE KITS CAN ONLY BE INSTALLED IN HOUSINGS WITH THE FOLLOWING MINIMUM DIMENSIONS. 2' KIT -- 24" LONG X 3.375"WIDE X 1.750"TALL. 4' KIT -- 48" LONG X 3.375"WIDE X 1.750"TALL. 6' KIT -- 72" LONG X 3.375"WIDE X 1.750"TALL. 8' KIT -- 96" LONG X 3.375"WIDE X 1.750"TALL.

2 WARNING: Before proceeding, read all instructions carefully to insure proper and safe installation. WARNING: Risk of fire or electrical shock. Disconnect power before installing or servicing. WARNING: Risk of electrical shock. High temperatures inside luminaire. Make certain line voltage corresponds with ballast's primary voltage. (See ballast label). WARNING: Risk of fire or electric shock. Install this kit only in the luminaires that has the construction features and dimensions shown in the photographs and/or drawings. WARNING: Risk of fire or electric shock. If not qualified, do not attempt installation. Contact a qualified electrician. WARNING: This product must be installed in accordance with the applicable installation code by a person familiar with construction and operation of the product and the hazards involved. WARNING: To prevent wiring damage or abrasion, do not expose wiring to edges of sheet metal or other sharp objects. WARNING: Do not touch the LEDs or place them face down on a surface as damage may occur. Doing so could contribute to premature failure. IMPORTANT: When removing lamps, always wear eye protection. Make sure area below fixture is clear. IMPORTANT: Not every unit is identical! Placement of proper luminaire section (by length, emergency option, etc.) within each row is important. Refer to layout drawing to verify row identification, product location, and feed points! Note: Do not make or alter any open holes in an enclosure of wiring or electrical components during kit installation. 1. CHECK PARTS LIST. G. """" ""' ZIZIZZ Ill I I ZI ZIZZZZ Z:ZIU IZZZI ZZZIZIZI I - ==================.=iii =IIIIZZ znz ZZ Z:UU IZIZZZ ZZZZI IZIZIZZZ 8FT KIT: TW0 2 4FT PANELS. TW0(2) LED BOARDS PER PANEL ONE! J 40W DRIVER. ONE 1 SURGE PROTECTOR. THREE 3) _#6 SELF DRILLING SCREWS. (FOR DRIVER & SURGE EIGHT(8) #"8 SELF DRILLING SCREWS. (FOR MOUNTING PLATE) TW0(2) ADHESIVE BACKED WIRE CLIPS. r PROTECTOR) (OPTIONAL STEP DOWN TRANSFORMER ALSO AVAILABLE SHIPPED SEPARATE G...,...,JJ&....;;;;:-- 6FT KIT: ONE(1) 6FT PANEL. THREE(3) LED BOARDS. ONE 1 30W DRIVER. ONE 1 1 SURGE PROTECTOR. THR E 3) #6 SELF DRILLING SCREWS. (FOR DRIVER & SURGE PROTECTOR) SIX(6) #8 SELF DRILLING SCREWS. (FOR MOUNTING PLATE) (OPTIONAL STEP DOWN TRANSFORMER TW0(2) ADHESIVE BACKED WIRE CLIPS. ALSO AVAILABLE, SHIPPED SEPARATE 4FT KIT: ONE 1 4FT PANEL. TW0(2) LED BOARDS. ONE l1 25W DRIVER. ONE 1 SURGE PROTECTOR. THR E 3) #6 SELF DRILLING SCREWS. (FOR DRIVER & SURGE FOUR(4) #8 SELF DRILLING SCREWS. (FOR MOUNTING PLATE) TWO 2 ADHESIVE BACKED WIRE CLIPS. PROTECTOR) (OPTIONAL STEP DOWN TRANSFORMER 2FT KIT: """ ii liiiil ON E 2FT PANEL. ONE( 1) LED BOARDS. ONE l 12W DRIVER. ONE 1 SURGE PROTECTOR. THR (3) #6 SELF DRILLING SCREWS. (FOR DRIVER & SURGE PROTECTOR) TW0(2) #8 SELF DRILLING SCREWS. (FOR MOUNTING PLATE) (OPTIONAL STEP DOWN TRANSFORMER ONE( 1) ADHESIVE BACKED WIRE CLIP. ALSO AVAILABLE, SHIPPED SEPARATE LS/Industries Inc Alliance Road + Cincinnati, OH Fax (513) Page 2 of 6

3 THE FOLLOWING INSTRUCTIONS ARE REPRESENTATIVE OF ALL KITS LAMP HOLDER & LEADS (REMOVE.DISCARD) HOUSING COVER (REMOVE BUT KEEP) -OLD HOUSING OLD BALLAST (CUT AND DISPOSE OF LAMP HOLDER LEADS & BALLASTLEADS IFBALLAST LEFT IN HOUSING) LAMPS -- (REMOVE.DISCARD) 2.) SHUT OFF POWER TO EXISTING FIXTURE. REMOVE EXISTING LAMPS. BALLAST COVERS LAMP HOLDERS & LAMP HOLDER WIRING. DO NOT DISPOSE OF HOUSING COVER OR CORRESPONDING SCREWS! DISCONNECT POWER FROM EXISTING BALLAST. EXISTING BALLAST CAN REMAIN IF IT DOES NOT INTERFERE WITH INSTALLATION OF NEW DRIVER OR DRIVER/STEP DOWN COMBINATION. DISPOSE OF /RECYCLE LAMPS AND LAMP HOLDERS APPROPRIATELY PER STATE AND LOCAL CODES. DRIVER LED BOARD/PANEL SURGE PROTECTOR DIMMING LEADS (CAPPED OFF) DO NOT USE! 3.) REMOVE DRIVER & SURGE PROTECTOR FROM BACK OF LED RETROFIT PANEL BY REMOVING SCREWS. DRIVER & SURGE PROTECTOR SHIPPED SECURED TO PANEL TO PREVENT DAMAGE DURING TRANSPORT. NOTE: ALL DRIVERS ARE RATED AC INPUT. IF SUPPLY VOLTAGE IS 347/480 A STEP DOWN TRANSFORMER ORDERED SEPARATELY IS REQUIRED. STEP DOWN INSTRUCTIONS PAGE 6. l Ext Fax LS/Industries Inc Alliance Road + Cincinnati, OH Fax (513) Page 3 of6

4 OFFSET STRIP SHOWN LED DRIVER STEP DOWN TRANSFORMER (OPTIONAL, SEE PAGE 6) WIRING OFF BOTH ENDS ON 6 & 8FT KITS 4.) USE PROVIDED SELF DRILLING SCREWS TO MOUNT DRIVER & SURGE PROTECTOR INSIDE EXISTING HOUSING. USE ADHESIVE BACKED WIRE CLIPS TO CAPTIVATE LEADS FROM DRIVER TO RETROFIT PANEL. PANEL IS NOW TETHERED IN PLACE. IMPORTANT: DRIVER MUST BE MOUNTED MINIMUM OF 3" FROM END OF HOUSING AND A MINIMUM OF 3" FROM STEP DOWN TRANSFORMER IF EQUIPPED. DISCONNECT PLUG (PROVIDED BY LSI) NOTES: SEE BALLAST FOR CURRENT AND VOLTAGE. HOT LEAD TO BLACK COMMON LEAD TO WHITE GROUND LEAD TO GREEN 5.) ATIACH POWER SUPPLY USING UL LISTED WIRE CONNECTORS. IMPORTANT NOTE! EXISTING MASTER/AUXILIARY WIRING SCHEMES INCOMPATIBLE WITH LED RETROFIT. POWER MUST BE ROUTED TO EACH DRIVER. Page4 of6 LSI Industries Inc Alliance Road + Cincinnati, OH Fax (513)

5 --- GAP FOR WIRING OLD SCREWS 6.) REATTM:H FIXTURE COVER USING lhe SCREWS REMOVED E'ARUER. BE SURE TIMT lhe LOOS CONNECTING lhe ORNER TO lhe LED PANEL RUN lhrough lhe GAPS CR A1ED BY REMOVING lhe I.AMP HW>ERS. NOlE: DO NOT MJJ1fl WIRES TO BECOME PINCHED BEIWEEN HOUSING AND COVER! OLD HOUSING LED BOARD/PANEL 7.) USING PROVIDED TEI< SCREWS. ATTM:H LED PANEL TO lhe EXISTING BAl..lm COVER. IMPORTANT: MAKE SURE GAPS FOR WIRE WAYS ME COVERED BY lhe RETROFIT PANELi IF INSTM.LED CORRECTLY lhe LEDS SHOULD BE NE'AR lhe CENTER OF lhe FIXTURE AND lhe TABS ON lhe RETROFIT KIT SHOULD COMPLEIB.Y COVER lhe WIRE WAYS ON B01H ENDS. FIXTURE NOW ROOY TO BE ENERGIZED. LSI Industries Inc Alliance Road + Cincinnati, OH Fax (513) Page 5 of 6

6 OPTIONAL STEP DOWN TRANSFORMER INSTALLATION BLUE FROM STEP DOWN TO BLACK FROM DRIVER STEP DOWN 4A.) USE PROVIDED SELF DRILLING SCREWS TO MOUNT STEP DOWN TRANSFORMER INSIDE EXISTING HOUSING. CONNECT TO DRIVER AS SHOWN ABOVE. IMPORTANT: DRIVER MUST BE MOUNTED MINIMUM OF 3 11 FROM END OF HOUSING AND A MINIMUM OF 3 11 FROM STEP DOWN TRANSFORMER (IF EQUIPPED). DISCONNECT PLUG (PROVIDED BY LSI) NOTES: SEE BALLAST FOR CURRENT AND VOLTAGE. HOT LEAD TO RED COMMON LEAD TO WHITE GROUND LEAD TO GREEN 48.) ATIACH POWER SUPPLY USING UL LISTED WIRE CONNECTORS. IMPORTANT NOTE! EXISTING MASTER/AUXILIARY WIRING SCHEMES INCOMPATIBLE WITH LED RETROFIT. POWER MUST BE ROUTED TO EACH DRIVER. LSI Industries Inc Alliance Road + Cincinnati, OH Fax (513) Page 6 of 6