Profibus DP slave. dual ported RAM 2Kbyte. Maximum length for I/O data. Maximum length for output data. Status display

Transcription

1 PROFIBUS DP SLAVE MODULE DPB 021 Profibus DP slave module DPB021 The DPB 021 DIAS module is an interface module between the Profibus and the DIAS bus. Via the DIAS bus the data at the dual port RAM can be processed. An RS232 connection is available for diagnosis. Technical data Performance data Field bus Memory Maximum length for I/O data Maximum length for input data Maximum length for output data Profibus interface Diagnostic interface Status display Profibus DP slave dual ported RAM 2Kbyte 368 Byte 244 Byte 244 Byte RS 485 max. baud rate 12 Mbaud RS 232 max. baud rate 9600 baud yes Electrical requirements Current drawn at the DIAS bus (I/ O/ P module supply) maximum 400 ma Connection requirements Required terminal module DKL 062 (article number: ) Mechanical coding Connection technique 9-pole D-Sub socket, Profibus interface 9-pole D-Sub plug, Profibus diagnosis Page 1 a

2 DPB 021 ROFIBUS DP SLAVE MODULE Miscellaneous Article number Module identification at the DIAS Bus 16#97 Hardware version 1.1 GSD file Software macro Standardization HIL_7501.gsd (provided on disc) profi_dp.fub UL (E247993) Environmental conditions Storage temperature C Operating temperature C Humidity EMV stability 0 95 %, without condensation in accordance with EN (Industrial area) Resistance to shocks EN m/s² Protective system EN IP 20 Mechanical dimensions 80 mm 98 mm 45mm 93 mm Page 2 b

3 PROFIBUS DP SLAVE MODULE DPB 021 Connections The Profibus connection is made by means of a 9-pole D-SUB socket on the DKL 062 terminal module. The diagnosis plug is also found here in the form of a 9-pole D-SUB plug. Profibus Diagnosis Page 3 a

4 DPB 021 ROFIBUS DP SLAVE MODULE Profibus Pin Signal Description 1 not assigned 2 not assigned 3 RxD / TxD P Data line B 4 not assigned 5 D-GND Data reference potential 6 VP Power supply 7 not assigned 8 RxD / TxD N Data line inverse A 9 not assigned Caution: The supply line VP is not surge-proof and must be protected external when using it (eg. with Bourns PTC fuse MF-R010, IT = 0,2A which can be installed in the DSUB plug) Diagnosis 9-pole D-SUB plug Pin Function 1 not assigned 2 RxD 3 TxD 4 DTR 5 GND 6 DSR 7 not assigned 8 CTS 9 not assigned Caution: For the configuration of the profi bus additional software SYCON from Hilscher is required! Page 4 c

5 PROFIBUS DP SLAVE MODULE DPB 021 Status displays LEDs showing the state of operation of the module are integrated into the front of the module. LED no. Colour Signal Description 2 yellow RDY ON COM ready FLASHES CYCLICALLY Bootstrap-loader aktive FLASHES NON-CYCLICALLY Hardware or system error OFF Hardware error 3 green RUN ON Communication running FLASHES CYCLICALLY Ready for communication FLASHES NON-CYCLICALLY Parameter error OFF No communication 4 yellow STA ON ASIC is in "ONLINE" operating state OFF ASIC is in "OFFLINE" operating state 12 red ERR ON Error in communication line OFF No error in communication line Page 5

6 DPB 021 ROFIBUS DP SLAVE MODULE Connection lines Profibus cable This interface is separated over a galvanic Optocoupler. For fault free operation, the cable must be equipped with a termination resistor. Profibus cable specification: The profibus standard defines cable type A as follows: (See also under FAQs.) Wave resistance: 35 to 165 Ohm at frequencies from 3 to 20MHz. Operating capacity: < 30 pf per meter. Cross section area of wires: > 0,34 mm², equal to AWG 22. Cable type: Twisted-pair cable. 1x2 or 2x2 or 1x4 wires. Loop resistance: < 110 Ohm per km. Signal damping: max. 9 db over the total connection length. Shielding: CU shielding network or CU shielding network and Cu shielding foil. Max. Bus length: 200m at 1500 kbit/s to 1,2km at 93,75 kbit/s. expandable through repeater. Applicable cable type: Example: Phoenix Contact PSM-CABLE-PROFIB/FC Profibus cable type A for fixed transfer rates to 12 MBit/s per EN , Type A Article-Nr. or Phoenix Contact: Applicable Profibus plug: When using the DKL062 terminal block, hardware version V1.0: Only conventional D-SUB connectors and housings can be used. When using the DKL062 terminal block hardware version V1.1 or higher: With this DKL version, the placement of the profibus socket was turned 180 degrees as compared to the hardware version V1.0 so that the special profibus connectors also can be used. Starting from hardware version V1.1, conventional D-SUB connectors and housing can be used as well as the special profibus connector. For example: 1. Phoenix Contact SUBCON9 With 90 angled cable outlet. or 2. Siemens Profibus connector 6ES7972-0BB10-0XA0 With bus termination switch. On the upper side, an additional socket is located to which an additional profibus connector can be connected. Page

7 Construction of the Profibus connection line: PROFIBUS DP SLAVE MODULE DPB 021 Cable type B Cable type A Baud rate < 500 kbaud > 500 kbaud R1 330 Ohm 390 Ohm R2 120 Ohm 220 Ohm Cable type: Profibus cable A or B All resistors 1/3 Watt Shield must be connected extensive to earth on both sides! The profibus resistance with spread resistors can only be set on the first and last modules. The Pins 6 (VP), 5 (D-GND) and 4 (CNTR-A) are not connected to the Profibus cable. Profibus cable: 2-pin, shielded Page 7 a

8 DPB 021 ROFIBUS DP SLAVE MODULE Profibus Termination Both end modules in a profibus system must have a line termination. This is necessary to avoid transfer errors caused by reflections in the line. Page

9 PROFIBUS DP SLAVE MODULE DPB 021 Profibus Connection To ensure a good profibus connection, it is necessary to observe the following wiring instructions: The profibus cable used must be designed for the transfer rate. The shielding must be connected to GND over the shortest route possible. To connect the individual wires, the cable must be stripped and the shielding shifted to the side. The insulation and shielding should only be removed as much as required. Caution must be taken to ensure that the profibus modules are connected to the same GND potential. Example e.g. DPB021 Insulation e.g. Profibus Module a 2 wire Twisted Pair Profibus cable b a, b...this distance should be as small as possible! Connect both sides of the shield to GND over the shortest route possible! Page 9

10 DPB 021 ROFIBUS DP SLAVE MODULE Diagnosis cable This interface is not electrically isolated. Therefore there must not be any differences in potential between the GND of the COM interface of the PC and the GND of the diagnosis interface, otherwise errors can occur. This can lead to damage to the module. Structure of the connection cable: 9 pole D-SUB socket 9 pole D-SUB socket PC COM interface Profibus module diagnosis interface The RxD and TxD leads must be cross bonded. Addressing Module code in the DIAS system: 16#97 Module address: can be set from 16#01 to 16#3C. Address Access Function 16#00 16#7F RD, WR PCS-n... Chip select PB module 16#80 RD RALO-n... Chip select address Port Low 16#81 RD RAHI-n... Chip select address Port High 16#82 WR WALO-n... Chip select address Port Low 16#83 WR WAHI-n... Chip select address Port High A macro is obtainable from SIGMATEK for the operation of the DPB021 DIAS module. For a detailed description you are directed to the macro handbook. Page