Tiny Size Power Over Ethernet PD Module. PRODUCT SELECTOR Nominal Input Voltage

Transcription

1 PEM00 SERIES PRODUCT SELECTOR Part Number Marking Nominal Input Voltage Output Voltage Efficiency Power (Maximum),7 (Volts DC) (Volts DC) (%) (Watts) PEM0. 0 PEM PEM PRODUCT OVERVIEW The PEM00 is a compact sized power extraction module, with complete IEEE 0.af PowerOverEthernet (PoE) standard compliance. They are designed to extract power from CAT5 or higher Ethernet cable when sourced from an IEEE 0.af compliant Power Sourcing Equipment (PSE). Accomplish Its high efficiency DCDC converter provides a well regulated low noise and low ripple output with inbuilt overload and output shortcircuit protection The PEM00 series provides a quick, easy, and low cost method for Ethernet equipment manufacturers to PoE enable their equipment. The PEM00 is one of the very small dimension PoE PD modules in the world and helps for compact sized PoE powered devices. PRODUCT FEATURES Fully IEEE 0.af compliant.95 watt output load Wide input voltage (V to 57V DC) Full Power start up even from V input.v, 5V, V DC output voltage models All models capable of.95w output Stable efficiency even at high ambient On board PI filter for output ripple control Overload and short circuit protection Minimal external components required 500 Volt DC isolation (Input to Output) Compact dimension of 7 x x 7 mm Adjustable output voltage RoHS compliant Low output ripple and noise Low cost In 5V and V model If maximum power is exceeded, the PEM00 will operate in over current mode and will auto recover when the over load condition is removed. ABSOLUTE MAXIMUM RATINGS 5, Supply Voltage (VCC) Storage Temperature (TS) Output Voltage (VOUT) 0V 57V DC 5 O C 00 O C 0V to controlled output voltage (operating or nonoperating) INPUT CHARACTERISTICS Parameter Symbol Min. Typ. Max. Units Input Voltage 7 VIN 57 Volts Under Voltage Lockout VUVLO 0 Volts Input Current, 0 IIN ma Operating Temperature 9 TOP O C IEEE 0.af Power Classification 0 Class 0 DC OUTPUT CHARACTERISTICS Parameter Symbol Min. Typ. Max. Units Line Regulation VLNRG 0.% Load Regulation VLDRG 0.5% Output Ripple and Noise 5, VRIP 0 mv pp Isolation Voltage VISOL 500 V DC Temperature Coefficient (Slope) TC ppm O C Figure BLOCK DIAGRAM and TYPICAL CONNECTIONS Input Input VIN SMAJ5A (ESD Protection) VIN IEEE 0.af Signature and Control PEM00 DCDC Converter (Optional) C Safety Capacitor (for EMI tuning) ADJ VDC DC Output VDC C 70uF Low ESR Output voltage typical ± % at TA of 5 0 C with a nominal input voltage and rated output current. VDC At nominal VIN at 7% load. 5 All specifications typical are at TA of 5 0 C with a nominal input voltage and rated output current unless otherwise noted. These are meant as a design aid only and are indicative, and not guaranteed. Exceeding the absolute maximum ratings may cause permanent damage to the product. We do not imply functional operation under these conditions. These ratings assume free air flow. 7 With minimum load current 00mA. Please refer to IEEE0.af standards document. Maximum input current is dependent on power class, and input voltage. Input current (DC or RMS) at V PORT =7vDC is 50mA, at V PORT =57vDC is 0mA. Peak inrush current is 00mA for 50mS max at duty cycle of 5% max. 9 Please see section F.. Thermal profile on operating temperature 0 Please see section F. Powered Device Signature VDC PEM00_B_R0_Draft Page of 5

2 PEM00 SERIES FUNCTIONAL DESCRIPTION F.. Inputs The PEM00 is compatible with all IEEE 0.af compliant Power Sourcing Equipment (PSE) and supports the different power injection options of Data/Signal pair (Mode A) or Spare Pair (Mode B). See Figure Typical System Configuration. As per IEEE 0.af, it is specified that the PSE does not apply power to the both outputs at the same time i.e. pair injection. (Refer to IEEE0.af standards for more information). The PEM00 provides for external input bridge rectifiers for improved system design flexibility, and distribution of heat generation. As an example, a system designer wanting to provide two RJ5 inputs, both of which are PoE enabled, but use only one PEM00 module to save costs. Another advantage is that this allows the system designer to control the type and costs of the input rectification diodes. Figure Typical System Configuration In Mode A Signal Pair injection, the signal lines carry both data and power. In Mode B Spare Pair injection, the Signal pair carries only data, and the spare pair carries power. IEEE 0.af COMPLIANT POWER SOURCING EQUIPMENT (PSE) / 5 SPARE PAIR 5 POWERED DEVICE (PD) PSE (V) TX DATA / SIGNAL PAIR RX VIN VDC PEM00 VIN VDC DC OUTPUT RX TX / 7 DATA / SIGNAL PAIR SPARE PAIR 7 F.. Powered Device (PD) Signature When the PEM00 is connected to a Cat 5e or greater Ethernet cable from an IEEE 0.af compliant Power Sourcing Equipment (PSE), Endspan or Midspan, it will automatically present a Powered Device (PD) signature to the PSE, as and when requested. The PSE will then recognise that a PD is connected to that line and supply power. The PEM00 presents class 0 detection to the PSE. F.. Isolation IEEE0.af section.. calls for a Powered Device (PD) to meet safety isolation requirement by meeting the electrical strength test of IEC 0950 sub clause.. Infomart s PoweredEthernet PEM00 modules meet or exceed 500V impulse test. This is also referred to as Hi Pot Test, Flash Tested, Withstand Voltage, Proof Voltage, Dielectric Withstand Voltage & Isolation Test Voltage. PEM00_B_R0_Draft Page of 5

3 PEM00 SERIES by F.. Output Voltage Adjustment The PEM00 series has an OADJ pin, which allows the output voltage to be increased or decreased from its nominal value using a /W power rating or greater and % tolerance resistor connected between the OADJ pin and either the VDC or VDC pin as per figures below. Only one connection i.e. between OADJ and VDC or between OADJ and VDC is permitted at a time. A change of more than ± 0% from nominal is not permitted. Please contact Infomart technical support for more details or specific resistor values. Figure Figure Figure 5 F.5. Pin Connections INPUT PINS VIN. This pin connects to the positive () output of the input bridge rectifiers VIN. This pin connects to the negative () output of the input bridge rectifiers To maintain isolation integrity, always connect respective input and output poles only via X or Y safety capacitor. Maintain isolation barrier on motherboard PCB as per physical package. OUTPUT PINS VDC. This pin provides the regulated output from the DC/DC converter. Max. Current A per pin. OADJ. The output voltage can be adjusted from its nominal value, by connecting an external resistor from this pin to either VDC pin or VDC pin. For more details please see section F.. 5 VDC. The ground return for VDC output. Max. Current A per pin. PEM00_B_R0_Draft Page of 5

4 PEM00 SERIES THERMAL PROFILE F.. Thermal Management As with any power component, the PEM00 modules generate heat. It is important that adequate ventilation and airflow be taken into consideration at the design stage. The quantum of heat generated by the PEM00 will depend on the output load it is required to drive. The maximum ambient operating temperature is 70 O C. Figure below, shows the thermal performance of the PEM00 with a nominal VDC input. The PEM00 thermal performance can be improved by forced airflow cooling over the module and by using a heat sink (a) glued on to the output diodes using a thermal glue, or (b) by a power plane heat sink described in Figure 7 below. The two methods can be combined. Figure Thermal Performance profile at nominal V in Output Power (Wa.s) 0 Figure 7 Power Plane Heat Sink PEM0 PEM05 PEM Indicative values Ambient Temperature ( O C) PEM00 Power Plane Heat Sink A power plane heat sink on the motherboard is a relatively simple method to draw some heat away from the PEM00 using the output pins (VDC and VDC) which are connected to a PCB heat sink on the motherboard. It is important to maintain electrical isolation between OADJ pin and the VDC and VDC pins to ensure proper output voltages. Place C close to output pins VDC OUTPUT C VDC These power plane heat sinks must be on the outer layers of the PCB and the PEM00 must not be fitted into a socket. This method can be combined with forced airflow cooling, and with a heat sink glued on to the two output diodes using a thermal glue. Figure PHYSICAL PACKAGE.0 Nom (7.0 Max) ± ± ± ± ± 0.5 PEM ± ± ± 0.5 RECOMMENDED PC BOARD LAYOUT.0 ± 0.5 Ø ± ± 0.50 Dimensions in mm APPLICATION NOTES PEM00_B_R0_Draft Page of 5

5 PEM00 SERIES Power Over Ethernet (PoE) is a technology for wired Ethernet, the most widely installed local area network technology in use today. PoE allows the electrical power necessary for the operation of each enddevice to be carried by data cables along with the data, rather than by separate power cords. Thus, it minimizes the number of wires used to install the network, resulting in lower cost, less downtime, easier maintenance and greater installation flexibility. The IEEE standard governing PoE is IEEE0.af. Compliance with this standard ensures interoperability between devices. The PEM00 series modules offering a modular solution, incorporating full IEEE0.af compatibility signature to the PSE and isolated onboard DC/DC converter. The PEM00 series are ideal modular system blocks allowing manufacturers of Ethernet equipment to PoE enable their equipment with minimal effort and cost. The PEM00 modules series offer simple and quicker product development, maximising return on investment. PEM00 can be powered using a user designed power supply which has adequate thermal and overcurrent protection. It is strongly recommended that only IEEE0.af compliant power supply equipment be used to prevent damage to the module, which lacks output stage thermal protection. ESD Protection: It is required that the system designer must provide ESD protection such as an SMAJ5A (unidirectional) or SMAJ5CA (bidirectional) TVS diode at the PEM00 input(s) to prevent damage from overvoltage surges and for system EMC compliance. APPLICATION AREAS Security and alarm systems Voice over IP phones Access control systems IP Cameras Displays, Net Monitors Figure 9 Sample PoE System Configuration Public address systems Wireless access points Environmental control Telemetry Remote environmental monitoring Infomart India Pvt. Ltd. Infomart Technologies Infomart Tech Park Americas sales office 99, 5 th Cross, 5 th Block, Koramangala 590, South Cooper St. #09 Bangalore , Karnataka Arlington, Texas, 707, USA India Tel : () 00 Tel : pesales@infomartgroup.com Infomart reserves the right to alter or improve the specification, internal design or manufacturing process at any time, without notice. Please check with your distributor or visit our website to ensure that you have the current and complete specification for your product before use. Infomart (India) Pvt. Ltd. All rights reserved. This publication, in full or in part, may not be copied, transmitted or stored in a retrieval system, or reproduced in any way including, but not limited to, magnetic, digital, photographic, photocopy, magnetic or other recording means, without prior written permission from Infomart (India) Pvt. Ltd. Infomart is a registered trademark of Infomart (India) Pvt. Ltd. PoweredEthernet is a trademark of Infomart (India) Pvt. Ltd. PEM00_B_R0_Draft Page 5 of 5