TM-Series. Technical Description TM-301 chassis Rev Q,

Transcription

1 TM-Series Technical Description TM-301 chassis Rev Q,

2 Transmode TD-TM301 Q 2 (26) 1 GENERAL The specifications and information within this manual are subject to change without further notice. All statements, information and recommendations are believed to be accurate but are presented without warranty of any kind. Users must take full responsibility for their application of any products. In no event shall be liable for any indirect, special, consequential or incidental damages, including, without limitation, lost profits or loss or damage to data arising from the use or inability to use this manual, even if Transmode or its suppliers have been advised of the possibility of such damages. 1.1 In commercial confidence The manual is provided in commercial confidence and shall be treated as such. 1.2 Document Revision History Revision Date Description of changes A First released version B Added information on max power consumption in card cage Added mechanical drawings, noise level values C Restriction: A CU is always required for configurations with 3 Traffic Units. D Transition to new Transmode format. No content change. E Clarifications and minor updates of figures F Updated with ordering numbers for different slot configurations G Added information on labels Added information on air filter H Cosmetically updates I Removal of configurations without CU J Updated with new article codes. Text changes to reflect introduction of CU-SFP K Change of logotype L Addition of 23 mounting. Enhancements. M Addition of chapter Addition of chapter Addition of Appendix with configuration examples N Updated tables in section to reflect release 13.0 content O Addition of max inrush current in Table 6 P Introduction of new AC/DC module and configuration without any half-sized slots Q MDU-8 units incorrectly stated not to be supported. Corrected Table

3 Transmode TD-TM301 Q 3 (26) Table of content 1 General In commercial confidence Document Revision History Functional Description Introduction Basic configurations TM-301 chassis Fan units Air filter Primary power alternatives External interfaces Card Cage Plug-in unit data & chassis compatibility Chassis Identity Labels Product identifiers Technical data Revision data Ordering data Spare parts Mechanical drawings APPENDIX TM-301 Configurations Line amplifier configuration G Terminal node Large Terminal node

4 Transmode TD-TM301 Q 4 (26) 2 FUNCTIONAL DESCRIPTION 2.1 Introduction The TM-301 chassis is the medium-sized chassis alternative in the TM-Series. The TM-301 is perfect for smaller collector nodes or to house an intermediate amplifier site. A Control Unit (CU) is always placed in the first slot. The CU gives an aggregated management view of the chassis. In the standard configuration, two full-sized units can be mounted together with up to four half-sized units. The TM-301 is provided in AC or DC primary powering options and different mounting options. For details on installation procedure, see TM-301 Installation Guide within the Installation & Commissioning volume of the TM-Series System manual. 2.2 Basic configurations A Basic TM-301 NE Equipment include Control Unit (CU-SFP) Dummy panels Dual Fan units Dual DC/DC converters with DC cables Ethernet cable, DSUB/RJ45 converter, ESD wrist wrap The mounting option adds on Mounting brackets 19, ETSI or 23 with screws and nuts The AC power option adds on Separate AC/DC converters For configurations where OSC channels are needed, the required amount of SFP s must be added separately. See Dimensioning Guidelines within System Manual for more details. Figure 1: Basic Equipment TM-301 with CU-SFP 2009

5 Transmode TD-TM301 Q 5 (26) 2.3 TM-301 chassis The TM-301 chassis can be divided into four parts: Fan area Card cage Power and external interfaces Fiber management area Figure 2: The main parts of a TM-301 NE Platform The Fan and Power and external interface modules are screwed to the mechanics but still easy to extract via handles. Different mounting brackets are used when mounting the TM-301 into an ETSI, 19 or a 23 building practice. Fiber slack can be handled via the fiber management area. A separate fiber management shelf is recommended for configurations with plug-in units having multiple client ports. 2009

6 Transmode TD-TM301 Q 6 (26) Fan units On the left a fan unit module is placed. It can easily be extracted and replaced by pulling the module outwards using the handle. Figure 3: Cooling of TM-301 The fan module contains two fan units. If one fan unit fails the red LED on the cover panel will ignite and an alarm will be generated to the Control Unit. The other FAN unit has the capacity to cool the system alone. A hot-swap of the failed unit can be done. On the far right side a mechanical air filter is placed. It can be extracted for replacement. The airflow is shown in Figure Air filter An air filter is placed on the far right hand side of the card cage. This filter should be extracted and cleaned every second year under normal conditions. See System Manual Operation & Maintenance, Spare Part & Maintenance Guide for more details. 2009

7 Transmode TD-TM301 Q 7 (26) Primary power alternatives On the right side, two slots are available for primary power configurations. AC-power An AC powered configuration is shown in Figure 4. The AC/DC conversion is done in an external unit and connected to one of the DC inlet modules. Two DC input modules are provided to allow for A & B power configurations. The AC voltage accepted is either 115 or 230V. Figure 4: AC power configuration A green LED indicator (PWR) is placed on the front of the module to indicate a functioning unit. Upon failure, the LED will be turned off and an alarm will be generated to the management system. A hot-swap replacement of the failed module can be done. The red LED (POL ERR) indicates polarity error, i.e. the 48 voltage has been wrongly connected. This is only a visual indication and will not generate any alarm to the management system. The AC/DC unit has a green LED indicator to indicate correct function. 2009

8 Transmode TD-TM301 Q 8 (26) DC-power External -48V DC power is here connected directly to the DC power inlet modules. The two modules are used to enable A & B power configurations. Both 2-wire and 3-wire configurations are possible. Figure 5: DC power configuration A green LED indicator (PWR) is placed on the front of the module to indicate a functioning unit. Upon failure, the LED will be turned off and an alarm will be generated to the management system. A hot-swap replacement of the failed module can be done. The red LED (POL ERR) indicates polarity error, i.e. the 48 voltage has been wrongly connected. This is only a visual indication and will not generate any alarm to the management system. Note! The same product (TM-301-DDC/19, /ETSI with R-state R1B) is used for both AC and DC powering. In the AC configuration external AC/DC units are added and connected to the DC inlet connectors. In the DC-configuration, the DC voltage is connected directly. The previous R-state R1A had a special DC-inlet module. Fuse 3,15A 2009

9 Transmode TD-TM301 Q 9 (26) External interfaces To the far right a LAN module is situated for electrical connections. Figure 6: LAN module Three RJ-45 connector types are available for the following applications: DCN 1 Management interface to the Network Element. A LAN-connection via Ethernet interface (10Mb/s or 100Mb/s) that can be connected directly to a Transmode Network Manager (TNM) platform or via a DCN network. ICN 3 & ICN 4 Internal Communication Network, used when connecting multiple TM- 301 platforms to create a larger NE. See Installation & Commissioning manual for further details. The electrical Ethernet interfaces can be connected to its interfacing equipment with an Ethernet cable and is suitable for connection to intra-building wiring only. The maximum allowed physical length of the cable is 100 m, provided that a Cat 5e class shielded cable is used and the shield is grounded at both ends. Unshielded cable usage is not warranted by Transmode and such usage is discouraged. 2009

10 Transmode TD-TM301 Q 10 (26) Card Cage Figure 7: TM-301 card cage area The card cage has one dedicated slot (slot 1) for a Control Unit (CU). The two following slots (2 & 3) are for full-height Traffic Units. Slots 4 to 7 are in the standard configuration used for four half-sized units, i.e. typically passive units. The wall between slots 4-5 and 6-7 can be reduced to provide one or two additional fullsized slots. This is reconfiguration that has to be done in production and consequently these configurations are ordered via separate ordering numbers (see chapter 4.2). Figure 8: Slot usage in standard configuration TM301xxyy/2 In the standard configuration TM301xxyy/2 the TM-301 can be equipped with up to two active units (Transponders, Muxponders, Optical Amplifiers) and four half-height units. 2009

11 Transmode TD-TM301 Q 11 (26) Figure 9: Slot usage in special configuration TM301xxyy/1 In the special configuration TM301xxyy/1 the TM-301 can be equipped with up to three active units (Transponders, Muxponders, Optical Amplifiers) and two half-height units. Figure 10: Slot usage in special configuration TM301xxyy/0 In the special configuration TM301xxyy/0 the TM-301 can be equipped with up to three active units (Transponders, Muxponders, Optical Amplifiers) and one passive full-height unit. Note! In the TM301xxyy/0 configuration the bottom slot 5 must only be equipped with passive units since the air flow from the fan unit is not sufficient for an active unit. In the TM301xxyy/0 configuration the slot 5 can be used for e.g. a MDU8EE unit. Note: In the special configurations TM301xxyy/1 and TM301xxyy/0 where three Traffic Units can be inserted, there are power dissipation restrictions that may prohibit some combinations of high-power units. Always verify that the power consumption is within the limits. In DC-powering the max power dissipation within the card cage is 120W. In AC-powering the max power dissipation is dependent on used AC/DC converter: - PS1A-120/DS3 restricts the power within the card cage to 101W. - PS1A-180/DS3 provides same power within the card cage as for DC, i.e. 120W. PS1A-180/DS3 was introduced in Dec 2009 and shipment of TM-301 in AC configuration is done with PS1A-180/DS3 from that point in time. A CU-SFP with OSC transceivers will consume 20W of the above values. A CU-SFP without OSC transceivers will consume 18W of the above values. 2009

12 Transmode TD-TM301 Q 12 (26) Plug-in unit data & chassis compatibility The below tables lists all plug-in units available at release For each plug-in unit a Type parameters is defined; Type has four parameters; A = Active unit, i.e. must be inserted in an active slot P = Passive unit, i.e. must be inserted in an active slot FH = Full-height unit, i.e. occupies a full-height slot HH = Half-height unit, i.e. occupies a half-height slot Every unit is a combination of Active/Passive and Full-height/Half-height. As an example: The TPQMR has the type A/FH meaning that the unit shall be inserted in an active, full-height slot. Table 1: Plug-in unit data and chassis compatibility (Release 14.0 content) Category Item Name Item ID Type Slot TM- TM- TM- TMwidth MultiRate 2500 DWDM Transponder V2 TPMR25-V2/xxxxx A/FH 1 Y Y Y Y Transponders Quad MultiRate xwdm Transponder TPQMR A/FH 1 Y Y Y Y Muxponders Double DGbE xwdm, Basic Unit TPDDGBE A/FH 1 Y Y Y 2.5G line rate 10-port GFP xwdm Muxponder GXP10/2500-SFP A/FH 1 Y Y Y Y 8-port SDH xwdm Muxponder MXP8 A/FH 1 Y Y Y MultiService Muxponder MS-MXP A/FH 1 Y Y Y Y 4G line rate Quad MultiService Transponder TPQMS A/FH 1 Y Y Y Y Double 10Gb/s Lite Basic Unit TPD10G-L-BU A/FH 1 Y Y Y Y 10Gb/s Transponder, Client-XFP, BU TP10GCLX/xxxxx A/FH 1 Y Y Y Y 10Gb/s C-band Tunable Transp TP10GCLX/TC A/FH 1 Y Y Y Y 10Gb/s C-band Tunable Ext Reach TP10G/TC-ER A/FH 1 Y Y Y 10G line rate Layer-2 10G C-band Tunable OTN Transponder TP10GOTN/TC A/FH 1 Y Y Y Y 9xGbE/10Gb Muxponder, BU GBE9-MXP10G A/FH 1 Y Y Y Y 9xGbE/10G FEC Muxponder GBE9/MXP10GFEC A/FH 1 Y Y Y Y Double 10Gb/s FEC Basic Unit TPD10GBE-BU A/FH 1 Y Y N Y 4xSTM-16/STM-64 Muxponder 4x2G5-MXP10G A/FH 1 Y Y Y Y MultiService MuxPonder 10G MS-MXP/10G A/FH 1 Y Y Y Y MultiService MXP Tunable 10G ER MS-MXP10G/TC-ER A/FH 1 Y Y N N 6-port GbE Ethernet Demarcation Unit EDU/6PGBE A/FH 1 Y Y Y Y 10xGbE/10GbE Ethernet Muxponder GBE10-EMXP10 A/FH 1 Y Y Y Y 22xGbE/10GbE Ethernet Muxponder GBE22-EMXP10 A/FH 2 Y Y N N 12-port GbE Ethernet Demarcation Unit EDU/12PGBE A/FH 1 Y Y Y Y Type A = Active unit, i.e. must be inserted in an active slot Type P = Passive unit, i.e. must be inserted in an active slot Type FH = Full-height unit, i.e. occupies a full-height slot Type HH = Half-height unit, i.e. occupies a half-height slot 2009

13 Transmode TD-TM301 Q 13 (26) Table 2: Plug-in unit data and chassis compatibility (Release 14.0 content), cont. Category Item Name Item ID Type DWDM Optical Add/drop DWDM Optical Mux/DeMux Misc DWDM Slot width TM ch DWDM Add-Drop Unit, AB-version AD1AB/xxxxx 1ch DWDM Add-Drop Unit, BA-version AD1BA/xxxxx P/HH 1 Y Y Y Y 2ch DWDM Add-Drop Unit, AB-version AD2AB/xxxxx 2ch DWDM Add-Drop Unit, BA-version AD2BA/xxxxx P/HH 1 Y Y Y Y 4ch DWDM Add-Drop Unit, AB-version AD4AB/xxxxx 4ch DWDM Add-Drop Unit, BA-version AD4BA/xxxxx P/HH 1 Y Y Y Y 2ch OA DWDM Add-Drop Unit AB AD2OAAB/xxxxx 2ch OA DWDM Add-Drop Unit BA AD2OABA/xxxxx P/HH 1 Y Y Y Y 1ch/2F A/D DWDM Add-Drop AD1-2F/xxxxx P/HH 1 Y Y Y Y 4ch/2-fiber DWDM Add-Drop AD4-2F/xxxxx P/HH 1 Y Y Y Y 1x4 ROADM 100GHz 1x4ROADM/100G A/FH 2 Y N N N 8ch Mux/DeMux, Extendable MDU8-E P/FH 1 Y Y N N 8ch Mux/DeMux, Terminal MDU8-T P/FH 1 Y Y N N 8ch Even Mux/DeMux, Extendable MDU8-E/EVEN-C P/FH 1 Y Y N N 8ch Even Mux/DeMux, Terminal MDU8-T/EVEN-C P/FH 1 Y Y N N 40ch MDU, even 50GHz DWDM MDU40/50G-EVEN A/FH 3 Y N N N 40ch MDU, odd 50GHz DWDM MDU40/50G-ODD A/FH 3 Y N N N MDU-E 8ch Even 50GHz DWDM MDU8EE P/FH 1 Y Y N N MDU-E 8ch Even 50GHz DWDM MDU8EE P/FH 1 Y Y N N MDU-E 8ch Even 50GHz DWDM MDU8EE P/FH 1 Y Y N N MDU-E 8ch Even 50GHz DWDM MDU8EE P/FH 1 Y Y N N MDU-E 8ch Even 50GHz DWDM MDU8EE P/FH 1 Y Y N N MDU-E 8ch Odd 50GHz DWDM MDU8EO P/FH 1 Y Y N N MDU-E 8ch Odd 50GHz DWDM MDU8EO P/FH 1 Y Y N N MDU-E 8ch Odd 50GHz DWDM MDU8EO P/FH 1 Y Y N N MDU-E 8ch Odd 50GHz DWDM MDU8EO P/FH 1 Y Y N N MDU-E 8ch Odd 50GHz DWDM MDU8EO P/FH 1 Y Y N N Optical Interleaver Unit 100/200GHz OIU-C-100/200 P/HH 1 Y Y Y Y Optical Interleaver Unit 50/100GHz OIU-C-50/100 P/HH 1 Y Y Y Y 8ch Variable Optical Attenuator unit VOA-8CH P/FH 1 Y Y N N 2-port OCM OCM/2p A/FH 1 Y Y N N 8ch Variable Optical Attenuator II VOA-8CH/II A/FH 1 Y Y N N 2ch Variable Optical Attenuator VOA-2CH A/HH 1 Y Y Y Y TM- 301 TM- 101 TM- 102 Table 3: Plug in unit data and chassis compatibility (Release 14.0 content), cont. Category Item Name Item ID Type Slot TM- TM- TM- TMwidth Optical Line Amplifier 17dBm C-band OA17C A/FH 1 Y Y Y Y Dual Optical Line Amplifier 17/17dBm C- band OA2-17/17CC A/FH 1 Y Y Y Y Optical Line Amplifier 20dBm C-band OA20C A/FH 1 Y Y Y Y Optical Dual Optical Line Amplifier 20/20dBm C- Amplifiers OA2-20/20CC A/FH 1 Y Y Y Y band Opt Low Gain Amp C-Band 20dBm OA20C/LG A/FH 1 Y Y Y Y Dual Opt Low Gain Amp C-Band 20dBm OA2-20/20/CC/LG A/FH 1 Y Y Y Y Opt Flat Gain Amp C-Band 10 dbm OA10C/FG A/FH 1 Y Y Y Y Type A = Active unit, i.e. must be inserted in an active slot Type P = Passive unit, i.e. must be inserted in an active slot Type FH = Full-height unit, i.e. occupies a full-height slot Type HH = Half-height unit, i.e. occupies a half-height slot 2009

14 Transmode TD-TM301 Q 14 (26) Table 4:Plug-in unit data and chassis compatibility (Release 14.0 content), cont. Slot TM- TM- TM- TM- Category Item Name Item ID Type width Optical Band Unit OBU1300/1550 P/HH 1 Y Y Y Y Misc passive 2xOptical Coupler Unit OCU2 P/HH 1 Y Y Y Y units 4xOptical Coupler Unit OCU4 P/HH 1 Y Y Y Y Active unit Protection Control Unit PCU/2P A/HH 1 Y N N N Table 5: Plug-in unit data and chassis compatibility (Release 14.0 content), cont. Category Item Name Item ID Type Slot TM- TM- TM- TMwidth ch Add/drop CWDM 1) (singlefiber) ADCWDM/yyyy P/HH 1 Y Y Y Y CWDM 1ch CWDM Add/drop (single-fiber) AD1C/yyyy P/HH 1 Y Y Y Y AD-filters 2x1ch Add/Drop CWDM (singlefiber) AD2X1C/yyyy P/HH 1 Y Y Y Y 1ch/2-fiber CWDM Add-Drop 2) AD1C-2F/yyyy P/HH 1 Y Y Y Y 4ch MDU CWDM, single fiber, TA MDUC4-TA/1470 4ch MDU CWDM, single fiber, TB MDUC4-TB/1470 P/HH 1 Y Y Y Y 4ch MDU CWDM, single fiber, EA MDUC4-EA/1270 P/HH 1 Y Y Y Y 4ch MDU CWDM, single fiber, EB MDUC4-EB/1270 CWDM 8ch CWDM Mux, fiber-pair MU-2F/1470 Optical P/HH 1 Y Y Y Y 8ch CWDM DeMux, fiber-pair DU-2F/1470 Mux/DeMux 4ch CWDM MDU fiber-pair MDU4-E-2F P/HH 1 Y Y Y Y Extendable 4ch CWDM MDU fiber-pair Terminal MDU4-T-2F P/HH 1 Y Y Y Y Type A = Active unit, i.e. must be inserted in an active slot Type P = Passive unit, i.e. must be inserted in an active slot Type FH = Full-height unit, i.e. occupies a full-height slot Type HH = Half-height unit, i.e. occupies a half-height slot 2009

15 Transmode TD-TM301 Q 15 (26) Chassis Identity Each chassis within a NE must have a unique ID number. The chassis identity is set by a DIP-switch that is located on the LAN module (see chapter 2.3.4). By extracting the module, the DIP-switch will be located on the to side of the board. See Figure 11. Figure 11: DIP switch for Chassis ID Up to 16 TM-301 chassis can be connected into one NE. However, normally only one TM- 301 would be used as a NE and stacking multiple TM-301 chassis should be rare. The procedure is described in the Installation & Commissioning Volume of the System Manual. 2009

16 Transmode TD-TM301 Q 16 (26) 3 LABELS The TM-301 chassis is marked with a Product Label and a System Label. Both are placed on the top of the chassis, on the left, front side. The Product label contains: Transmode logotype 2. Product number 3. Product revision 4. Barcode 128 containing: product number space revision 5. Production date: yearwweeknumber 6. Serial number 7. Barcode 128 containing: serial number 8. Barcode 128 containing: product number, revision, production date, serial number 9. Approval markings 2009

17 Transmode TD-TM301 Q 17 (26) The System Label contains: 1. Transmode logotype 2. System type 3. Production date: yearwweeknumber 4. Ratings 5. Laser class, 6. Compliance info, 7. Approval markings 2009

18 Transmode TD-TM301 Q 18 (26) 3.1 Product identifiers Figure 12: Product labels All exchangeable modules on the Basic NE Equipment are labeled. The figure shows labeling of Fan unit LAN module DC-inlet module TM-301 Chassis The label contains the following information: Product number R-state Serial number Bar code with the above information The above information on these specific modules is not accessible via the inventory function in the management system. Inventory data on CU s and Traffic Units are available via the inventory functionality. 2009

19 Transmode TD-TM301 Q 19 (26) 4 TECHNICAL DATA Table 6: Mechanical & electrical data TM-301 Height 3U / 133mm Depth 280mm / 11 Width (excl. mounting brackets) 445mm/17.5 Primary Power DC-inlets. Redundant, Hot-swap Cooling Redundant fans. Hot-swap Mounting ETSI, 19, 23 Fiber management Yes LAN/Mgmt connections RJ45 Primary power range, AC: External AC/DC-converter VAC, 50/60Hz, 2.5A Class I. PS1A-120/DS3 excl connectors. Size AC/DC converter Length: 180mm Width: 95mm Height: 50mm Primary power range DC: 48VDC ( VDC), 5A Class III Max power at AC powering 160 W Max power at DC powering 150 W ~120W in DC powering Max power consumption in card ~101W in AC powering using PS1A-120/DS3 cage (incl CU-SFP) ~120W in AC powering using PS1A-180/DS3 Max Inrush -48VDC 4,0A / 4ms 7,5 kg Weight DC-powering: (mechanics + fan unit + 2x DC TM-301(DC) + LAN module 1,5mm 2 DC cable size (connector limit) Standard 1,0mm 2 Table 7: Capacity TM-301 Number of full-sized slots 1) Up to 3 Number of half-sized slots 2) Up to 4 No of λ in largest possible 8 CWDM or configuration 3) 3 DWDM No of λ in smallest possible configuration 4) 1 CWDM or DWDM wavelength (via 1ch add/drop) 1) Slots for Traffic units (Transponders/MuxPonders) 2) Slots for passive units (Add/drop filters, MDU s) 3) Includes both Traffic units and passive unit within same chassis, i.e. a fully configured NE 4) Using Transponder and optical unit with lowest granularity Note: The TM-301 chassis can mechanically be configured for 2x full-slots + 4x half-slots or 3x full-slots + 2x half-slots 2009

20 Transmode TD-TM301 Q 20 (26) 4.1 Revision data A TM-301 chassis has an order level that includes mechanics, cables, Control Unit etc as listed in chapter 4.2. The table shows revision data on M301/ENC which is the basic card cage mechanics. Changes in this basic mechanics is reflected on the M301/ENC level Table 8: Revision data Product number Rev Introduced Release M301/ENC R1A A2.2 1 st released version R1B A Ordering data Table 9: Configuration alternatives Basic NE-Equipment TM-301 Configuration Ordering code Comments TM-301, DC, 19 Shelf=2 TM301DC19/2 Standard config. TM-301, AC, 19, Shelf=2 TM301AC19/2 Standard config. TM-301, DC, ETSI Shelf=2 TM301DCET/2 Standard config. TM-301, AC, ETSI, Shelf=2 TM301ACET/2 Standard config. TM-301, DC, 23 Shelf=2 TM301DC23/2 Standard config. TM-301, AC, 23, Shelf=2 TM301AC23/2 Standard config. TM-301, DC, 19 Shelf=1 TM301DC19/1 Special config. TM-301, AC, 19, Shelf=1 TM301AC19/1 Special config. TM-301, DC, ETSI Shelf=1 TM301DCET/1 Special config. TM-301, AC, ETSI, Shelf=1 TM301ACET/1 Special config. TM-301, DC, 23 Shelf=1 TM301DC23/1 Special config. TM-301, AC, 23, Shelf=1 TM301AC23/1 Special config. TM-301, DC, 19 Shelf=0 TM301DC19/0 Special config. TM-301, AC, 19, Shelf=0 TM301AC19/0 Special config. TM-301, DC, ETSI Shelf=0 TM301DCET/0 Special config. TM-301, AC, ETSI, Shelf=0 TM301ACET/0 Special config. TM-301, DC, 23 Shelf=0 TM301DC23/0 Special config. TM-301, AC, 23, Shelf=0 TM301AC23/0 Special config. When OSC channels are required, SFP s must be added to the above ordering numbers. See Dimensioning Guidelines within the System Manual for more details. 2009

21 Transmode TD-TM301 Q 21 (26) The above ordering numbers include the following items: TM-301 card cage Control Unit CU-SFP (1 per chassis) DC/DC filter module (2 items per chassis) External AC/DC converter 115/230V 120W (2 per chassis, only for AC configuration) LAN module / RJ 45 card (1 per chassis) Dummy panels, full-sized (2 items) Dummy panels, half-sized (4 items) DC cable, 4m (2 items) Ethernet cable, 2m (1 item) DSUB adapter RJ45/DB9 (1 item) ESD wrist wrap with strap (1 item) Mounting material in rack; nuts, plastic plates, screws (4 sets) Mounting brackets 19 (mounted, 2 per chassis) Mounting brackets ETSI (2 per chassis, only in ETSI version) Mounting brackets 23 (2 per chassis, only in 23 version) Spare parts The TM-301 chassis has the following spare part items: Table 10: Spare parts Item name Item code Comment Fan unit TM-301 M301-FAN One module used per chassis DC power plugin module -48V M301-DC Two modules used per chassis LAN module TM-301 M301-RJ45 One per chassis AC/DC converter (external) PS1A-120/DS3 Two per chassis (replaced by PS1A-180/DS3) M301 ACDC Unit (180W) PS1A-180/DS3 Two per chassis Dummy panel 6HE inkl ovl o EMC-list M3-DU/6HE Full-height slot cover panel Dummy panel 3HE inkl ovl o EMC-list M3-DU/3HE Half-height slot cover panel M301 airfilter M9-M301/AIR One per chassis 2009

22 Transmode TD-TM301 Q 22 (26) 4.3 Mechanical drawings ETSI reference plane 2009

23 Transmode TD-TM301 Q 23 (26) ETSI reference plane 2009

24 Transmode TD-TM301 Q 24 (26) 5 APPENDIX 5.1 TM-301 Configurations Line amplifier configuration Figure 13: Line amplifier NE with OSC channels CU-SFP (with SFP's for OSC channels) 20 W Double OA20 27 W Not used OSC AD-filter OSC AD-filter Not used Not used 47 W total Figure 14: Board placement and power consumption 2009

25 Transmode TD-TM301 Q 25 (26) G Terminal node Figure 15: 4x10G Terminal NE using TPD10G-BU CU-SFP (w/o SFP's for OSC channels) 18 W TPD10GBE-BU 43 W TPD10GBE-BU 43 W 4ch MDU-E 2F Not used Not used Not used 104 W total Figure 16: Board placement and power consumption 2009

26 Transmode TD-TM301 Q 26 (26) Large Terminal node Figure 17: 4x10G Terminal NE using mix of units This configuration uses the special TM-301 configuration enabling three full-sized slots and two half-sized slots. CU-SFP (w/o SFP's for OSC channels) 18 W GBE9/MXP10GFEC 32 W MS-MXP 20 W TPDDGBE 25 W MDUC4-TA/1470 MDUC4-TB/ W total Figure 18: Board placement and power consumption 2009