HPE Director Blade Installation Instructions

Transcription

1 HPE Director Installation Instructions Overview Use these installation instructions if you have purchased one of the optional director s listed in Table (page ). Install the s in compatible director models oy. NOTE: This document refers to s by their short names. Table Director s Model Short name (im- printed on ) Part number Compatible HPE director models HPE SN00B Gb -port FC FC- Q0UA SN00B -Slot Director, SN00B -Slot HPE SN00B Gb SAN Extension SX Q0UA SN00B -Slot Director, SN00B -Slot HPE SN00B Gb p SFP+ Integrated FC- Q0UA SN00B -Slot Director, SN00B -Slot HPE SN00B Gb p SW SFP+ Extension SX Q0UA SN00B -Slot Director, SN00B -Slot HPE DC0 Gb Core CR- CRA CRB CRC DC0 SN000B -Slot Copyright 0, 0 0 Hewlett Packard Enterprise Development LP HPE DC Backbone Director Gb Core CR CRA CRB CRC DC Director Director SN000B Gb -Port FC FC EY0A -Slot Part Number: 00-9 Published: September 0 Edition: *00-9* SN000B Gb -port Enhanced Fibre Channel FC-E QW90A QW90B -Slot Page

2 Short name (im- printed on ) Table Director s (continued) Model Part number Compatible HPE director models Table Director s (continued) Model Short name (im- printed on ) Part number Compatible HPE director models SN000B Gb -port Enhanced Fibre Channel HPE SN000B Gb p SFP Integrtd FC-E FC- QW9A QW9B EYA EYB -Slot -Slot -port Gb FC -port Gb FC FC- FC- A990A A990B AGA AGB -Slot / / HPE SN000B Gb p SFP Integrtd HPE SN000B Gb -port FC HPE SN000B Gb -port FC HPE B-series 0/ FCoE HPE B-series Enhanced MP Extension DC SAN Director Switch Multi-protocol Extension option FC- FC- FC- FCOE0- FX-E FX- EY9A EY9B QKA QKB QKC QKD QKA QKB QKC QKD APA APB APC CRA CRB CRC APA APB -Slot -Slot -Slot DC Director, DC0, Director DC Director, DC0 SAN Slot SAN Backbone Director, SN000B Slot DC Director, DC0, -Slot -port Gb FC -port Gb FC -port Gb FC -port Gb FC DC SAN Director -port Gb Fibre Channel B-series Multi-protocol (MP) Router FC- FC- FC- FC- FC- FR-i A99A A99B AKA AKB AKC AKD AK9A AK9B AK9C AK9D AK0A AK0B AK0C AK0D / /, DC Director, DC0 /, DC Director, DC0 /, DC Director, DC0 BK9A DC BK9B Director, DC0, BK9C -Slot AGA AGB / For instructions on installing the Gb Core Processor, see the HPE SAN DC and DC0 director switch to an HPE SN000B -slot and -slot director switch upgrade guide This is also supported in slot of the DC SAN Director Encryption FS- AR9A AR9B AR9C DC Director, DC0, Director Switch with FOS v..0x and higher. For full support details, see the Fabric OS administrator s guide. Page

3 NOTE:. For interoperability information on Hewlett Packard Enterprise storage products, see the single point of connectivity knowledge for Hewlett Packard Enterprise storage products (SPOCK) website at On the SPOCK home page, under the Other Hardware section, click Switches. Identifying components This section identifies the components. NOTE: to top. Ports are numbered from bottom FC- Components Figure FC- FC FC Port numbering. Port status LED. Status LED. Port Page

4 SX Components Figure SX CR- Components Figure CR- SX. Status LED. Status LED. 0 GbE ports 0-. FC Ports 0-. /0 GbE ports -. QSFP port map and trunking diagram. QSFP Connectors Page

5 CR- Components Figure CR- FC-E components Figure FC-E. QSFP port map and trunking diagram. QSFP connectors -. QSFP connectors -. QSFP connectors -. QSFP Connectors 0-. FC ports. FC ports. Status LED. Port and trunking group map. FC ports 0. FC ports Page

6 FC-E components Figure FC-E FC- components Figure FC-. Status LED. FC ports. FC ports. FC ports 0. FC ports 0. Port status LED. FC ports. Port and trunking group map. FC ports Page

7 FC- components Figure FC- FC- components Figure 9 FC-. FC ports 0. Status LED. FC ports. Status LED. Port status LED for FC port. Power LED. QSFP port 9; FC ports -9 Page

8 FCOE0- components Figure 0 FCOE0- FX- components Figure FX- and FX-E. 0-GbE FCoE ports 0. GbE ports 0. Status LED. 0-GbE FCoE ports. 0-GbE ports 0. FC ports 0. Status LED. GbE ports 9. FC ports Page

9 FS- components Figure FS- FC- components Figure FC FC. Status LED. Status LED. FC port. Port status LED. FC Port. Port speed LED. FC ports 0. Port status LED. FC ports 0 Page 9

10 FC- components Figure FC- FC- components Figure FC FC 0. Status LED. Status LED. FC Port. Port speed LED (left port). FC Port. Port status LED. Port status LED (left port). Port speed LED (right port). FC ports. FC ports 0. Port status LED (right port). FC ports 9. FC ports 0 Page 0

11 FC- components Figure FC- FC- components Figure FC-. Status LED. Status LED. FC Port. Port status LED. FC Port. Port status LED. FC ports 0. FC ports. FC ports 0 Page

12 FC- components Figure FC- FC- components Figure 9 FC Status LED. Status LED. Power LED. FC Port. Port status LED. FC Port. Port status LED. FC ports. FC ports 0. FC Port. FC Port. FC ports. FC ports 0 NOTE: FC- supports mini-sfps (msfps) oy. Page

13 FR-i components Figure 0 FR-i Small form-factor pluggable (SFP) transceivers, as needed (must be ordered separately) uess option with integrated transceivers ordered Quad SFP (QSFP) transceivers, as needed (must be ordered separately) Optical cables, as needed Transceiver support GE0 GE The FC- supports msfps oy, and is shipped with them installed. The FC- supports xgb FC QSFPS, and is shipped with them installed. Except for the FC- and FC- QSFP, all Gb, Gb, and Gb s use B-series SFPs, uess they come pre-bundled with Brocade transceivers. In either case, the functionality is equivalent. CR- and CR- use QSFP transceivers for ICL connections. The SFP-integrated FC-, FC-, FC-, and SX s are shipped with the SFPs installed. For more information about supported transceivers, see the Hewlett Packard Enterprise SPOCK website at You must sign up for HP Passport to gain access. For information on SAN compatibility, see FR i. FC Port. GbE ports 0. Status LED. Port status LED. FC ports 0 Verifying installation requirements The installation takes less than 0 minutes. You will need the following items: Replacement director Filler panel for each empty slot (ships with the director ) Electrostatic discharge (ESD) grounding strap Workstation computer Phillips screwdriver Removing the filler panel Remove the filler panel, if installed. There are three filler panel types (Figure (page )). CAUTION: Remove a filler panel oy when installing or replacing a Director. All slots that are not occupied by a Director require a filler panel to ensure cooling of the chassis and protection from dust. To remove a filler panel with a handle:. Unscrew the two captive screws on the filler panel.. Grasp the handle and remove the filler panel. To remove a filler panel with ejectors:. Push in the yellow tab on each ejector.. Open both ejectors and remove the filler panel. To remove a filler panel with pull tabs: Page

14 . Unscrew the top and bottom captive screws on the filler panel.. Grasp the top and bottom pull tabs and remove the filler panel. Figure Removing filler panels FCOE0- FC- FC- FX E FS- FX- CR CR Installing the CAUTION: Wear an ESD grounding strap when handling the. On the director chassis, the grounding connection is located above the power connectors.. Filler panel with handle. Handle. Ejectors (). Pull tabs (). Captive screws (). Filler panel with ejectors. Captive screws () Determining the ejector type. Filler panel with pull tabs Installation procedures vary depending on the ejector mechanism on the. This section identifies the s that use ejectors and sliders, and the s that use ejectors oy. s with ejectors and slider switches The following s use both ejectors and slider switches: FC- FC- s with ejectors FR-i The following s use ejectors oy: FC- FC-E FC- FC- FC- SX FC-E FC- FC- FC- To install the :. Identify the ejector type for your, as described in Determining the ejector type (page ).. Locate an appropriate slot. Slots are numbered from left to right when facing the port side of the chassis. For the / : Install the s in slots through and through 0. For the DC Director: Install the s in slots through and 9 through. The CR- is installed in slot & as a pair. For the DC0 : Install the s in slots and and slots and. The CR- is installed in slot & as a pair. For the Director: Install the s in slots through and 9 through. Install the FCOE0- in slot oy. For the SN000B -Slot : Install the s in slots and and slots and. For the SN00B -Slot Director: Install the s in slots through and 9 through. For the SN00B -Slot : Install the s in slots and and slots and.. Orient the so that the ports face outward (away from the slot) and the flat (noncomponent) side is on the left.. Proceed to Step if the you are installing uses ejectors oy. (See Determining the ejector type (page ).) For s with both ejectors and slider switches: Page

15 a. Open the ejectors approximately degrees, align the flat side of the inside the upper and lower rail guides in the slot, and then, while applying slight pressure to the left, slide the into the slot (Figure (page )). f. Turn the on by tighten the thumb screw on the top of the using the Phillips screwdriver. Figure Removing and replacing a with ejectors oy (FC- shown) Figure Removing and replacing a Director with ejectors and slider switches (FC- shown). Director chassis. FC-. Ejectors. / chassis. On/Off slider switch. FC-. Ejectors () b. Close the ejectors by pushing the handles toward the center of the until the ejectors lock. The levering action of the handles seats the in the slot. c. Tighten the thumb screw inside each handle using the Phillips screwdriver. d. Turn the on by sliding up the slider switch in the top ejector, covering the thumb screw. e. Proceed to Step.. For s with ejectors: a. Open the ejectors. b. Align the flat side of the inside the upper and lower rail guides in the slot. c. Slide the into the slot until it is firmly seated (Figure (page )). d. Close the ejectors by moving the handles away from the center of the.. e. Tighten the thumb screw on the bottom of the using the Phillips screwdriver.. Verify that the power LED is displaying a steady green light and that the is firmly seated.. Install the transceivers and cables. For more information This document provides initial setup and configuration procedures oy. For comprehensive configuration procedures (including those for mixed- configurations), see the following: B-series SAN backbone director switch hardware reference guide B-series SN000B -Slot SAN director switch hardware reference guide StorageWorks DC and DC0 SAN director switch hardware reference guide iscsi gateway service administrator guide Brocade Fabric OS administrator's guide For the latest documentation and firmware releases, see Page