WalT: testing sensor networks and distributed environments

Transcription

1 WalT: testing sensor networks and distributed environments E. Dublé, F. Rousseau, J. Baranguán, J. Zeni, I. Juc, P.-H. Frohring, B. Faure April 7, 2014 LIG / DRAKKAR 1 / 18

2 The problem Contents 1 The problem 2 The WalT project 3 WalT: how it works 4 Demos 2 / 18

3 The problem The problem How to efficiently debug a distributed system? Sensor networks: even harder (constrained devices) 3 / 18

4 The problem WSNs: existing solutions Senslab - IoT-Lab, other public platforms: Pros: many nodes, readily available Cons: remote access, not very flexible (e.g. you cannot replace a sensor) Hand-made one-time experiment: Pros: on your own desk, very flexible, local setup Cons: time-consuming setup, not conceivable for many nodes 4 / 18

5 The WalT project Contents 1 The problem 2 The WalT project 3 WalT: how it works 4 Demos 5 / 18

6 The WalT project The WalT approach WalT: Wireless Testbed Intermediary approach: Local in your lab or company Open source testbed management software Open documentation and hardware recommendations You buy the (cheap) infrastructure, the project provides the rest of the stack 6 / 18

7 The WalT project WalT nodes and network Walt nodes are built on a cheap (around 35 ) Single-Board-Computer called Raspberry Pi 1 Walt nodes boot an OS stored on the LAN. Depending on the use case, it may be: Your choice of Linux distribution Android (if you simulate a network of smartphones) Walt nodes are linked together using a Power-Over-Ethernet network 1 We may evolve to another platform in the future if needed / valuable. 7 / 18

8 The WalT project WalT scenarios 1 Sensor networks: connect 1 or more sensors to each RPi node The RPi is used as a gateway to communicate with the sensor and control it (flash, reboot) Useful to test WSN protocols 2 Distributed systems: use the RPi nodes themselves Useful to test data management systems, TCP congestion avoidance optimizations, etc. 8 / 18

9 The WalT project Founding AGIR (UJF/INP) 2013/2014: Hardware, trainees ST: Sensors, industrial contract (up to end 2013) 9 / 18

10 WalT: how it works Contents 1 The problem 2 The WalT project 3 WalT: how it works 4 Demos 10 / 18

11 WalT: how it works WalT architecture (scenario 1) 11 / 18

12 WalT: how it works Collecting sensor traces / 18

13 WalT: how it works Collecting sensor traces... trace from sensor X : sending <packet> 12 / 18

14 WalT: how it works Collecting sensor traces / 18

15 WalT: how it works Collecting sensor traces... trace from sensor Y : received <packet> trace from sensor Z : received <packet> 12 / 18

16 WalT: how it works...and then: The traces are analysed by the server (e.g. which sensors received this packet? ) The traces are then directed to the VizWalT GUI 13 / 18

17 WalT: how it works WalT GUI: VizWalT A modified simulator: cooja VizWalT reuses cooja s interface But: In an unmodified cooja : each node is smart In VizWalt : each node reflects the behaviour of a real sensor 14 / 18

18 WalT: how it works Technical challenges Sensors send traces through their serial link, which is slow (slower than the radio!) It may disturb the behavior of the sensor. Solutions being implemented: Send only one small part of the packet (enough to identify it). Improve the serial link driver (use DMA). Synchronization issues (being explored) Cooja-related issues (real-nodes versus emulated-nodes paradigm) 15 / 18

19 Demos Contents 1 The problem 2 The WalT project 3 WalT: how it works 4 Demos 16 / 18

20 Demos Demos 1 Preliminary version of a WalT tesbed management tool 2 Sample WalT session with DSME nodes 17 / 18

21 The end... Questions? 18 / 18