H3C S5820X&S5800 Switch Series

Transcription

1 H3C S5820X&S5800 Switch Series OAA Command Reference Hangzhou H3C Technologies Co., Ltd. Software version: Release 1211 Document version: 6W

2 Copyright 2011, Hangzhou H3C Technologies Co., Ltd. and its licensors All rights reserved Trademarks No part of this manual may be reproduced or transmitted in any form or by any means without prior written consent of Hangzhou H3C Technologies Co., Ltd. H3C,, Aolynk,, H 3 Care,, TOP G,, IRF, NetPilot, Neocean, NeoVTL, SecPro, SecPoint, SecEngine, SecPath, Comware, Secware, Storware, NQA, VVG, V 2 G, V n G, PSPT, XGbus, N-Bus, TiGem, InnoVision and HUASAN are trademarks of Hangzhou H3C Technologies Co., Ltd. Notice All other trademarks that may be mentioned in this manual are the property of their respective owners The information in this document is subject to change without notice. Every effort has been made in the preparation of this document to ensure accuracy of the contents, but all statements, information, and recommendations in this document do not constitute the warranty of any kind, express or implied.

3 Preface The H3C S5800&S5820X documentation set includes 12 command references, which describe the commands and command syntax options for the S5800&S5820X Release1211. The OAA Command Reference describes OAA configuration commands. This preface includes: Audience Added and modified commands Conventions About the H3C S5800&S5820X documentation set Obtaining documentation Technical support Documentation feedback Audience This documentation is intended for: Network planners Field technical support and servicing engineers Network administrators working with the S5800 and S5820X switch series Added and modified commands None Conventions This section describes the conventions used in this documentation set. Command conventions Convention Boldface Italic Bold text represents commands and keywords that you enter literally as shown. Italic text represents arguments that you replace with actual values. [ ] Square brackets enclose syntax choices (keywords or arguments) that are optional. { x y... } [ x y... ] { x y... } * Braces enclose a set of required syntax choices separated by vertical bars, from which you select one. Square brackets enclose a set of optional syntax choices separated by vertical bars, from which you select one or none. Asterisk marked braces enclose a set of required syntax choices separated by vertical bars, from which you select at least one.

4 [ x y... ] * &<1-n> Asterisk marked square brackets enclose optional syntax choices separated by vertical bars, from which you select one choice, multiple choices, or none. The argument or keyword and argument combination before the ampersand (&) sign can be entered 1 to n times. # A line that starts with a pound (#) sign is comments. GUI conventions Convention Boldface Window names, button names, field names, and menu items are in Boldface. For example, the New User window appears; click OK. > Multi-level menus are separated by angle brackets. For example, File > Create > Folder. Convention < > Button names are inside angle brackets. For example, click <OK>. [ ] Window names, menu items, data table and field names are inside square brackets. For example, pop up the [New User] window. / Multi-level menus are separated by forward slashes. For example, [File/Create/Folder]. Symbols Convention WARNING CAUTION IMPORTANT NOTE TIP An alert that calls attention to important information that if not understood or followed can result in personal injury. An alert that calls attention to important information that if not understood or followed can result in data loss, data corruption, or damage to hardware or software. An alert that calls attention to essential information. An alert that contains additional or supplementary information. An alert that provides helpful information. About the H3C S5800&S5820X documentation set The H3C S5800&S5820X documentation set includes: Category Documents Purposes Product description and specifications Pluggable module description Marketing brochures Technology white papers PSR150-A [ PSR150-D ] Power Modules User Manual Describe product specifications and benefits. Provide an in-depth description of software features and technologies. Describes the appearances, features, specifications, installation, and removal of the pluggable 150W power modules available for the products. PSR300-12A [ PSR300-12D1 ] Power Modules User Manual Describes the appearances, features, specifications, installation, and removal of the pluggable 300W power modules available for the products.

5 Power configuration PSR750-A [ PSR750-D ] Power Modules User Manual RPS User Manual LSW1FAN and LSW1BFAN Installation Manual LSW148POEM Module User Manual S5820X [ S5800 ] Series Ethernet Switches Interface Cards User Manual H3C OAP Cards User Manual H3C Low End Series Ethernet Switches Pluggable Modules Manual S C-PWR Ethernet Switch Hot Swappable Power Module Ordering Guide RPS Ordering Information for H3C Low-End Ethernet Switches Describes the appearances, features, specifications, installation, and removal of the pluggable 750W power modules available for the products. Describes the appearances, features, and specifications of the RPS units available for the products. Describes the appearances, specifications, installation, and removal of the pluggable fan modules available for the products. Describes the appearance, features, installation, and removal of the pluggable PoE module available for the products. Describes the models, hardware specifications, installation, and removal of the interface cards available for the products. Describes the benefits, features, hardware specifications, installation, and removal of the OAP cards available for the products. Describes the models, appearances, and specifications of the pluggable modules available for the products. Guides you through ordering the hot-swappable power modules available for the S C-PWR switches in different cases. Provides the RPS and switch compatibility matrix and RPS cable specifications.

6 Hardware installation Software configuration Operations and maintenance S5800 Series Ethernet Switches Quick Start S5820X Series Ethernet Switches Quick Start S5800 Series Ethernet Switches CE DOC S5820X Series Ethernet Switches CE DOC S5800 Series Ethernet Switches Quick Start S5820X Series Ethernet Switches Quick Start S5800 Series Ethernet Switches Installation Manual S5820X Series Ethernet Switches Installation Manual Pluggable SFP[SFP+][XFP] Transceiver Modules Installation Guide S C-PWR Switch Video Installation Guide S5820X-28C Switch Video Installation Guide Configuration guide Command reference H3C Series Ethernet Switches Login Password Recovery Manual Release notes Provides regulatory information and the safety instructions that must be followed during installation. Guides you through initial installation and setup procedures to help you quickly set up and use your device with the minimum configuration. Provides a complete guide to hardware installation and hardware specifications. Guides you through installing SFP/SFP+/XFP transceiver modules. Shows how to install the H3C S C-PWR and H3C S5820X-28C Ethernet switches. Describe software features and configuration procedures. Provide a quick reference to all available commands. Tells how to find the lost password or recover the password when the login password is lost. Provide information about the product release, including the version history, hardware and software compatibility matrix, version upgrade information, technical support information, and software upgrading.

7 Obtaining documentation You can access the most up-to-date H3C product documentation on the World Wide Web at Click the links on the top navigation bar to obtain different categories of product documentation: [Technical Support & Documents > Technical Documents] Provides hardware installation, software upgrading, and software feature configuration and maintenance documentation. [Products & Solutions] Provides information about products and technologies, as well as solutions. [Technical Support & Documents > Software Download] Provides the documentation released with the software version. Technical support Documentation feedback You can your comments about product documentation to We appreciate your comments.

8 Contents OAP card configuration commands 1 oap connect 1 oap reboot 2 ACFP configuration commands 3 acfp server enable 3 display acfp client-info 3 display acfp policy-info 5 display acfp rule-info 7 display acfp server-info 9 ACSEI configuration commands 11 acsei client close 11 acsei client reboot 11 acsei server 12 acsei server enable 12 acsei timer clock-sync 13 acsei timer monitor 13 display acsei client info 14 display acsei client summary 16 Index 18 i

9 OAP card configuration commands oap connect oap connect slot slot-number system system-name User view 2: System level slot slot-number: Specifies an OAP card on a member device of an Intelligent Resilient Framework (IRF) virtual device. The slot-number argument takes the member ID of the member of the IRF virtual device, and its value ranges depend on the number of member devices and there member IDs. system system-name: Specifies the system name of the OAP card on the certain device. The system-name argument specifies the OAP system name of the card in the form of SubSlotX with X as the slot number of the OAP card. For example, the system name of the OAP card in slot 3 is SubSlot3. Examples Use the oap connect command to redirect from the switch to the software system of the specified OAP card. NOTE: When this command is executed, the terminal display interface is switched from the command line interface (CLI) on the switch to the operating interface of the software system of the OAP card, and you can manage the system and application software on the OAP card. To return from the software system on the OAP card to the CLI of the switch, press Ctrl+K. You can install multiple OAP cards on some models of the S5800 and S5820X switches. If you log in to the software system of one OAP card first, you cannot log in to the software system of another by using the oap connect command. To log in to the software system of another OAP card, return to the CLI on the switch by pressing Ctrl+K. In an IRF virtual device, you can use the oap connect command repeatedly to log in to the software systems of multiple OAP cards installed on different member switches, but cannot log in to the software systems of multiple OAP cards installed on the same member switch simultaneously. # Redirect from the device to the software system of the OAP card in slot 3 of the member device 1. <Sysname> oap connect slot 1 system SubSlot3 Press CTRL+K to quit. Connected to SubSlot3 1

10 oap reboot oap reboot slot slot-number system system-name User view 2: System level slot slot-number: Restart the software system of an OAP card on a member of an IRF virtual device. The slot-number argument takes the member ID of the member of the IRF virtual device, and its value ranges depend on the number of member devices and there member IDs. system system-name: Specifies the system name of the OAP card on the certain device. The system-name argument specifies the system name of the OAP card in the form of SubSlotX with X as the slot number of the OAP card. For example, the system name of the OAP card in slot 3 is SubSlot3. Use the oap reboot command to restart the software system of the specified OAP card. Examples # Restart the software system of the OAP card in slot 3 of member device 1. <Sysname> oap reboot slot 1 system SubSlot3 This command will recover the SubSlot3 from shutdown or other failed state. Warning: This command may lose the data on the hard disk if the SubSlot1 is not being shut down! Continue? [Y/N]:y Reboot SubSlot1 by command. 2

11 ACFP configuration commands acfp server enable acfp server enable undo acfp server enable System view 2: System level None Use the acfp server enable command to enable the ACFP server. Use the undo acfp server enable command to disable the ACFP server. By default, the ACFP server is disabled. NOTE: In case that the ACSEI server is enabled on the device, when you first disable and then enable the ACFP server, to ensure that the ACFP collaboration rules can be resent to the ACFP server, you must also disable and then enable the ACSEI server. Related commands: acsei server enable (ACSEI Configuration Commands in the OAA Command Reference). Examples # Enable the ACFP server. <Sysname> system-view [Sysname] acfp server enable display acfp client-info Any view display acfp client-info [ client-id ] [ { begin exclude include } regular-expression ] 1: Monitor level 3

12 client-id: Displays information of the specified ACFP client, where client-id is the ACFP client identifier, in the range of 1 to : Filters command output by specifying a regular expression. For more information about regular expressions, see CLI configuration in the Configuration Fundamentals Configuration Guide. begin: Displays the first line that matches the specified regular expression and all lines that follow. exclude: Displays all lines that do not match the specified regular expression. include: Displays all lines that match the specified regular expression. regular-expression: Specifies a regular expression, which is a case sensitive string of 1 to 256 characters. Use the display acfp client-info command to display the information about the specified ACFP client(s). NOTE: If no ACFP client ID is specified, the information about all the ACFP clients is displayed. Examples # Display the information about all the ACFP clients. <Sysname> display acfp client-info ACFP client total number: 1 ClientID: 4 : IPS Hw-Info: 1.0 OS-Info: Linux Kernel App-Info: 2.0 Client IP: Client Mode: mirror Table 1 Output description Field ACFP client total number ClientID Hw-Info OS-Info App-Info Client IP Client Mode Total number of ACFP clients Client ID, index of client list information of client Hardware information of the client Operating system information of the client Application software information of the client Client IP address Working mode supported on the client: redirect: redirect mode mirror: mirror mode 4

13 display acfp policy-info display acfp policy-info [ client client-id [ policy-index ] dest-interface interface-type interface-number in-interface interface-type interface-number out-interface interface-type interface-number ] [ active inactive ] [ { begin exclude include } regular-expression ] Any view 1: Monitor level client client-id: Displays the policy sent by the specified ACFP client, where client-id is the ACFP client ID, in the range of 1 to policy-index: Policy index, in the range of 1 to dest-interface interface-type interface-number: Displays all the policies that use the specified interface (destination interface) for connecting to the ACFP client, where interface-type interface-number is the interface type and interface number. in-interface interface-type interface-number: Displays all the policies that use the specified interface as the inbound interface, where interface-type interface-number is the interface type and interface number. out-interface interface-type interface-number: Displays all the policies that use the specified interface as the outbound interface, where interface-type interface-number is the interface type and interface number. active: Displays active policies only. inactive: Displays inactive policies only. : Filters command output by specifying a regular expression. For more information about regular expressions, see CLI configuration in the Configuration Fundamentals Configuration Guide. begin: Displays the first line that matches the specified regular expression and all lines that follow. exclude: Displays all lines that do not match the specified regular expression. include: Displays all lines that match the specified regular expression. regular-expression: Specifies a regular expression, which is a case sensitive string of 1 to 256 characters. Use the display acfp policy-info command to display the ACFP policy information. NOTE: When you use this command to display the policy information sent by the specified ACFP client, if you specify the policy-index argument, the command displays the information about the policy whose number is policy-index applied by the ACFP client with an ID of client-id. Otherwise, the command displays the information about all the policies sent by the ACFP client with an ID of client-id. If neither the active nor inactive keyword is specified, the command displays all the active or inactive policies. If no argument is specified, the command displays the information about all the policies. 5

14 xamples # Display the information about the effective policies for all the packets that use GigabitEthernet 1/0/1 as the inbound interface. <Sysname> display acfp policy-info in-interface gigabitethernet 1/0/1 active ACFP policy total number: 1 ClientID: 1 Policy-Index: 2 Rule-Num: 20 ContextID: 2007 Exist-Time: (s) Life-Time: (s) Start-Time: 9:00 End-Time: 12:00 Admin-Status: enable Effect-Status: active DestIfFailAction: reserve Priority: 4 In-Interface: GigabitEthernet1/0/1 Out-Interface: GigabitEthernet1/0/2 Dest-Interface: Ten-GigabitEthernet1/3/1 Table 2 Output description Field ACFP policy total number ClientID Policy-Index Rule-Num ContextID Exist-Time Life-Time Start-Time End-Time Admin-Status Effect-Status DestIfFailAction Priority In-Interface Out-Interface Dest-Interface Total number of ACFP policies Client ID, index of client list Policy index Number of rules under the policy Context ID For how long the policy existed, in seconds Policy expiration time, in seconds Policy start time Policy end time Policy administration status Whether the policy is effective. If the policy dest-interface is down, the action to all rules under the policy will be either of the following one: delete: Keep the redirected and mirrored packets being forwarded (for forwarding first devices, select the delete action); reserve: Discard the redirected and mirrored packets (for security first devices, select the reserve action). Priority of a policy, number notation, in the range of 1 to 8 (the bigger the number, the higher the priority). Inbound interface of the packet Outbound interface of the packet Interface connected to the ACFP client 6

15 display acfp rule-info display acfp rule-info { in-interface [ interface-type interface-number ] out-interface [ interface-type interface-number ] policy [ client-id policy-index ] } [ { begin exclude include } regular-expression ] Any view 1: Monitor level in-interface: Displays ACFP rule information in order of inbound interface. The ACFP rule information which does not include the inbound interface is not displayed. out-interface: Displays ACFP rule information in order of outbound interface. The ACFP rule information which does not include the outbound interface is not displayed. interface-type interface-number: Specifies an interface by its type and number. policy: Displays the ACFP rule information in order of policy. client-id: ACFP client ID, in the range of 1 to policy-index: Policy index, in the range of 1 to : Filters command output by specifying a regular expression. For more information about regular expressions, see CLI configuration in the Configuration Fundamentals Configuration Guide. begin: Displays the first line that matches the specified regular expression and all lines that follow. exclude: Displays all lines that do not match the specified regular expression. include: Displays all lines that match the specified regular expression. regular-expression: Specifies a regular expression, which is a case sensitive string of 1 to 256 characters. Examples Use the display acfp rule-info command to display ACFP rule information. NOTE: When you use this command to display ACFP rule information in order of policy, if you specify neither client ID nor policy index, the rule information of all the policies is displayed. When you use this command to display ACFP rule information in order of outbound/inbound interface, if you specify no interface, the rule information for all the inbound interfaces or outbound interfaces is displayed. # Display ACFP rule information in order of inbound interface. <Sysname> display acfp rule-info in-interface gigabitethernet 1/0/1 In-Interface: GigabitEthernet1/0/1 ACFP rule total number: 1 ClientID:2 Policy-Index:2 Rule-Index:5 SMAC: DMAC: StartVLAN:2000 EndVLAN:2004 7

16 PackRate:128 Kbps Action:rate Status:active OperationStatus:succeeded # Display ACFP rule information in order of policy. <Sysname> display acfp rule-info policy 1 1 ACFP Rule total number: 1 ClientID:1 Policy-Index:1 Rule-Index:1 SIP: SMask: SPort:65500 to DIP: DMask: DPort:65500 to Protocol:ipinip Fragment:false DSCP:AF11 Action:redirect Status:inactive OperationStatus:succeeded Table 3 Output description Field In-Interface ACFP rule total number ClientID Policy-Index Rule-Index SMAC DMAC StartVLAN EndVLAN PackRate SIP SMask SPort DIP DMask DPort Protocol Fragment Inbound interface of the packet Total number of ACFP rules Client ID, index of client list Policy index Rule index Source MAC address Destination MAC address Start VLAN of the source VLAN End VLAN of the source VLAN Value of the restricted rate of packets, in kbps. Source IP address Inverse mask of source IP address Source port number Destination IP address Inverse mask of destination IP address Destination port number Protocol of the packet: GRE, ICMP, IGMP, IPinIP, OSPF, TCP, UDP, IP, and so on. Whether the packet is a fragment: true: Indicates the packet is a fragment false: Indicates all the packets, not concerned about whether the packet is a fragment or not ToS Type of Service, indicated by a number in the range of 0 to 15 Pre Packet precedence, indicated by a number in the range of 0 to 7 DSCP Differentiated Services Code Point, indicated by characters for Be, Ef, Af11, Af12, Af13, Af21, Af22, Af23, Af31, Af32, Af33, Af41, Af42, Af43, Cs1, Cs2, Cs3, Cs4, Cs5, Cs6, and Cs7 and indicated by a number in the range 0 to 63 for other code points 8

17 Field TCPFlag TCPMask Action Status OperationStatus The value is six bits, which represents URG, ACK, PSH, RST, SYN, and FIN respectively from low to high. The value is six bits, which represents URG mask, ACK mask, PSH mask, RST mask, SYN mask, and FIN mask respectively from low to high. For each bit, the value 1 indicates that this bit is concerned, and the value 0 indicates that this bit is not concerned. Action, including: permit deny mirror redirect rate: rate limit Rule status: active or inactive Rule application status: succeeded or failed display acfp server-info Examples display acfp server-info [ { begin exclude include } regular-expression ] Any view 1: Monitor level : Filters command output by specifying a regular expression. For more information about regular expressions, see CLI configuration in the Configuration Fundamentals Configuration Guide. begin: Displays the first line that matches the specified regular expression and all lines that follow. exclude: Displays all lines that do not match the specified regular expression. include: Displays all lines that match the specified regular expression. regular-expression: Specifies a regular expression, which is a case sensitive string of 1 to 256 characters. Use the display acfp server-info command to display ACFP server information. # Display ACFP server information. <Sysname> display acfp server-info Server-Info: ipserver redirect mirror Max Life-Time: (s) PersistentRules: false ContextType: HGPlus-context 9

18 Table 4 Output description Field Server-Info Max Life-Time PersistentRules ContextType ACFP client working mode supported by the ACFP server: redirect: redirect mode mirror: mirror mode Maximum expiration time (in seconds) of the collaboration policy supported by the server Whether the server supports permanent collaboration rules. Context ID types supported by the server: no-context: No context ID is carried. HG-context: Carrying the preamble HG as the context ID. HGPlus-context: Carrying the preamble HGPlus as the context ID. FlowID-context: Carrying the preamble Flow ID as the context ID. VLANID-context: Carrying VLAN ID as the context ID. The S5800&S5820X switches support carrying the preamble HGPlus as the context ID (the HGPlus-context) only. 10

19 ACSEI configuration commands acsei client close Examples acsei client close client-id ACSEI server view 2: System level client-id: ID of the ACSEI client to be closed. An ACSEI client ID is assigned by the ACSEI server, which ranges from 1 to 10. Use the acsei client close command to close the specified ACSEI client. # Close ACSEI client 1. <Sysname> system-view [Sysname] acsei server [Sysname-acsei-server] acsei client close 1 acsei client reboot acsei client reboot client-id ACSEI server view 2: System level client-id: ID of the ACSEI client to be restarted, which ranges from 1 to 10. Use the acsei client reboot command to restart the specified ACSEI client. Examples # Restart ACSEI client 1. <Sysname> system-view [Sysname] acsei server [Sysname-acsei-server] acsei client reboot 1 11

20 acsei server acsei server System view 2: System level None Use the acsei server command to enter ACSEI server view. Examples # Enter ACSEI server view. <Sysname> system-view [Sysname] acsei server [Sysname-acsei-server] acsei server enable acsei server enable undo acsei server enable System view 2: System level None Use the acsei server enable command to enable ACSEI server. Use the undo acsei server enable command to disable ACSEI server. By default, ACSEI server is disabled. Examples # Enable ACSEI server. <Sysname> system-view [Sysname] acsei server enable 12

21 acsei timer clock-sync acsei timer clock-sync minutes undo acsei timer clock-sync ACSEI server view 2: System level minutes: Value of the synchronization timer that is used for clock synchronization from ACSEI server to ACSEI client. It ranges from 0 to 1440 (in minutes), where value 0 specifies to disable the clock synchronization from ACSEI server to ACSEI client. Use the acsei timer clock-sync command to set the synchronization timer that is used for clock synchronization from ACSEI server to ACSEI client. Use the undo acsei timer clock-sync command to restore the default. By default, the clock sychronization timer is set to five minutes. Examples # Set the clock synchronization timer from ACSEI server to ACSEI client to 20 minutes. <Sysname> system-view [Sysname] acsei server [Sysname-acsei-server] acsei timer clock-sync 20 acsei timer monitor acsei timer monitor seconds undo acsei timer monitor ACSEI server view 2: System level seconds: Value of the monitoring timer that is used for ACSEI server to monitor ACSEI clients. It ranges from 0 to 10 (in seconds), where 0 specifies to disable ACSEI server from monitoring ACSEI client. Use the acsei timer monitor command to set the monitoring timer for ACSEI server to monitor ACSEI client. Use the undo acsei timer monitor command to restore the default. 13

22 Examples By default, the monitoring timer is set to 5 seconds. # Set the monitor timer for ACSEI server to monitor ACSEI client to 6 seconds. <Sysname> system-view [Sysname] acsei server [Sysname-acsei-server] acsei timer monitor 6 display acsei client info Any view display acsei client info [ client-id ] [ { begin exclude include } regular-expression ] 1: Monitor level client-id: ID of an ACSEI client, which ranges from 1 to 10. : Filters command output by specifying a regular expression. For more information about regular expressions, see CLI configuration in the Configuration Fundamentals Configuration Guide. begin: Displays the first line that matches the specified regular expression and all lines that follow. exclude: Displays all lines that do not match the specified regular expression. include: Displays all lines that match the specified regular expression. regular-expression: Specifies a regular expression, which is a case sensitive string of 1 to 256 characters. Use the display acsei client info command to display the ACSEI client information. The client information is retrieved from the advertisement packet sent by the client, so that when there is no ACSEI client information, the command displays the information keywords only. If executed without the client-id argument, the command displays information about all the ACSEI clients in order of registration time. Examples # Display information about ACSEI client 1. <Sysname> display acsei client info 1 Total Client Number: 1 Client ID: 1 Client : Hardware: System Software: Application Software: CPU: Intel(R) Pentium(R) M processor 1.40GHz PCB Version: 3.00 CPLD Version:

23 Bootrom Version: 1.12 CF card: 256 MB Memory: 512 MB Harddisk: 40.0 GB # Display information about all ACSEI clients. <Sysname> display acsei client info Total Client Number: 2 Client ID: 1 Client : Hardware: System Software: Application Software: CPU: Intel(R) Pentium(R) M processor 1.40GHz PCB Version: 3.00 CPLD Version: 1.00 Bootrom Version: 1.12 CF card: 256 MB Memory: 512 MB Harddisk: 40.0 GB Client ID: 2 Client : Hardware: System Software: Application Software: CPU: Intel(R) Pentium(R) M processor 1.40GHz PCB Version: 3.00 CPLD Version: 1.00 Bootrom Version: 1.12 CF card: 256 MB Memory: 512 MB Harddisk: 40.0 GB Table 5 Output description Field Client ID Client Hardware System Software Application Software CPU PCB Version CPLD Version Bootrom Version ID of the ACSEI client ACSEI client description Hardware version of the ACSEI client System software name and version of the ACSEI client Application name and version of the ACSEI client CPU information of the ACSEI client PCB version of the ACSEI client CPLD version of the ACSEI client Boot ROM version of the ACSEI client 15

24 Field CF card Memory Harddisk CF card information of the ACSEI client Memory information of the ACSEI client Harddisk information of the ACSEI client display acsei client summary display acsei client summary [ client-id ] [ { begin exclude include } regular-expression ] Any view 1: Monitor level client-id: ID of an ACSEI client whose summary is to be displayed, in the range of 1 to 10. : Filters command output by specifying a regular expression. For more information about regular expressions, see CLI configuration in the Configuration Fundamentals Configuration Guide. begin: Displays the first line that matches the specified regular expression and all lines that follow. exclude: Displays all lines that do not match the specified regular expression. include: Displays all lines that match the specified regular expression. regular-expression: Specifies a regular expression, which is a case sensitive string of 1 to 256 characters. Use the display acsei client summary command to display ACSEI client summary information. Summary information of multiple ACSEI clients is displayed in order of registration time. If executed without the client-id argument, the command displays summary information about all the ACSEI clients. Examples # Display the summary of ACSEI client 1. <Sysname> display acsei client summary 1 Total Client Number: 1 Client ID: 1 Status: Open MAC Address: 00e0-fc0a-c3ef Interface: GigabitEthernet5/0 Last registered: 02/08/ :00:00 # Display the summary of all ACSEI clients. <Sysname> display acsei client summary Total Client Number: 2 Client ID: 1 16

25 Status: Open MAC Address: 00e0-fc0a-c3ef Interface: GigabitEthernet5/0 Last registered: 02/08/ :00:00 Client ID: 2 Status: Open MAC Address: 00e0-fa1e-03da Interface: GigabitEthernet6/0 Last registered: 02/08/ :00:00 Table 6 Output description Field Client ID Status MAC Address Interface Last registered ID of the ACSEI client ACSEI client status MAC address of the ACSEI client Interface carrying the ACSEI client The last registration time of the ACSEI client 17

26 Index A D O A acfp server enable,3 acsei client close,11 acsei client reboot,11 acsei server,12 acsei server enable,12 acsei timer clock-sync,13 acsei timer monitor,13 D display acfp client-info,3 display acfp policy-info,5 display acfp rule-info,7 display acfp server-info,9 display acsei client info,14 display acsei client summary,16 O oap connect,1 oap reboot,2 18