RESIDENTIAL. R-410A Refrigerant Single Speed: 2-6 Tons Dual Capacity: 2-6 Tons. Submittal Data English Language/IP Units SD /08

Transcription

1 ESIDENTIAL -0A efrigerant Single Speed: -6 Tons Dual apacity: -6 Tons Submittal Data English Language/IP Units SD8 0/08

2 -6 Tons 60Hz Model Nomenclature N D V 09 A T L Model Type eturn Air onfiguration N= Envision L= Left = ight ompressor Type D= Dual apacity Discharge Air onfiguration S= Single Speed B= Bottom T= Top abinet onfiguration S= Side V= Vertical E= End H= Horizontal oax Options Unit apacity = opper N= upronickel Vintage A= urrent Fan Option 0= PS Voltage = EM = 08-0/60/ = Oversized EM Blower Option (06,08,0,08,09) = Oversized PS Blower Option (0,00,06,0,08) Hot Water Option 0= None = Hot Water Generation with factory installed pump Notes: PS Motor - Single Speed Only WaterFurnace works continually to improve its products. As a result, the design and specifications of each product at the time of order may be changed without notice. Please contact WaterFurnace at for latest design and SD8 0/08 Page of

3 -6 Tons 60Hz Performance Standard AI/ISO/ASHAE 6- The performance standard AI/ASHAE/ISO 6- became effective January, 000 and replaces AI Standards 0,, and 0. This new standard has three major categories: Water Loop (comparable to AI 0), Ground Water (AI ), and Ground Loop (AI 0). Although these standards are similar there are some differences: Unit of Measure: The ooling OP The cooling efficiency is measured in EE (US version measured in Btuh per Watt. The Metric version is measured in a cooling OP (Watt per Watt) similar to the traditional OP measurement. Water onditions Differences Entering water temperatures have changed to reflect the centigrade temperature scale. For instance the water loop heating test is performed with 68 F (0 ) water rounded down from the old 70 F (. ). Air onditions Differences Entering air temperatures have also changed (rounded down) to reflect the centigrade temperature scale. For instance the cooling tests are performed with 80.6 F (7 ) dry bulb and 66. F (9 ) wet bulb entering air instead of the traditional 80 F (6.7 ) DB and 67 F (9. ) WB entering air temperatures. 80.6/66. data may be converted to 80/67 using the entering air correction table. This represents a significantly lower relative humidity than the old 80/67 of 0% and will result in lower latent capacities. Pump Power orrection alculation Within each model, only one water flow rate is specified for all three groups and pumping Watts are calculated using the following formula. This additional power is added onto the existing power consumption. Pump power correction = (gpm x 0.06) x (Press Drop x 990) / 00 Where gpm is waterflow in gpm and Press Drop is the pressure drop through the unit heat exchanger at rated water flow in feet of head. Fan Power orrection alculation Fan power is corrected to zero external static pressure using the following equation. The nominal airflow is rated at a specific external static pressure. This effectively reduces the power consumption of the unit and increases cooling capacity but decreases heating capacity. These Watts are significant enough in most cases to increase EE and OPs fairly dramatically over AI 0,, and 0 ratings. Fan Power orrection = (cfm x 0.7) x (esp x 9) / 00 Where cfm is airflow in cfm and esp is the external static pressure at rated airflow in inches of water gauge. ISO apacity and Efficiency alculations The following equations illustrate cooling calculations: ISO ooling apacity = ooling apacity (Btuh) + (Fan Power orrection (Watts) x.) ISO EE Efficiency (W/W) = ISO ooling apacity (Btuh) x. / [Power Input (Watts) - Fan Power orrection (Watts) + Pump Power orrection (Watt)] The following equations illustrate heating calculations: ISO Heating apacity = Heating apacity (Btuh) - (Fan Power orrection (Watts) x.) ISO OP Efficiency (W/W) = ISO Heating apacity (Btuh) x. / [Power Input (Watts) - Fan Power orrection (Watts) + Pump Power orrection (Watt)] omparison of Test onditions AI 0 ISO/AI 6- WLHP AI ISO/AI 6- GWHP AI 0 ISO/AI 6- GLHP ooling Entering Air - DB/WB F 80/ /66. 80/ /66. 80/ /66. Entering Water - F / Fluid Flow ate * ** ** ** ** ** Heating Entering Air - DB/WB F Entering Water - F /70 0 Fluid Flow ate * ** ** ** ** ** Note *: Flow rate is set by 0 F rise in standard cooling test Part load entering water conditions not shown. WLHP = Water Loop Heat Pump; GWHP = Ground Water Heat Pump; GLHP = Ground Loop Heat Pump Note **: Flow rate is specified by the manufacturer onversions: Airflow (lps) = FM x 0.7; WaterFlow (lps) = GPM x 0.06; ESP (Pascals) = ESP (in wg) x 9; Press Drop (Pascals) = Press Drop (ft hd) x 990 WaterFurnace works continually to improve its products. As a result, the design and specifications of each product at the time of order may be changed without notice. Please contact WaterFurnace at for latest design and SD8 0/08 Page of

4 -6 Tons 60Hz AI/ISO 6- Performance atings Flow ate Water Loop Heat Pump ooling EWT 86 F Heating EWT 68 F Ground Water Heat Pump ooling EWT 9 F Heating EWT 0 F Ground Loop Heat Pump ooling Brine Full Load 77 F Part Load 68 F Heating Brine Full Load F Part Load F ap. apacity EE apacity apacity EE apacity apacity EE apacity OP OP OP Model Mod Motor gpm cfm Btuh Btuh/W Btuh Btuh Btuh/W Btuh Btuh Btuh/W Btuh Full EM , ,000. 9,000.0,00.0 7, , Part EM ,00 8.6,600 6.,000. 8,00., ,00.7 Full EM ,000 7.,00. 9,00., , , Part EM 8 0 8, , ,00.,800. 0,00 0.0,00. Full EM 00 8,00.8 7,00.,00.7 7,00.7 0, , Part EM 00,900 8., ,800 8.,000. 8,700.,000.7 Full EM , ,00. 70, , , , Part EM 00 7,000 8.,00.8, ,600.8,00.6 6,000. Full EM , , , ,900. 7, , Part EM 6 800, ,00. 6,00 6.0, ,800.,000. single EM ,700 7.,00 6., ,800.,700.0, single PS ,600 7., , ,800.0,00 0.,000.8 single EM ,00 9.,700.8,00 8.8, ,00.9 0, single PS ,00 8.,700. 0,900 7., ,00. 9,800.8 single EM 9 00, , , ,00.,000.0, single PS 9 00, , ,00.7 0,00.7, ,00.0 single EM 00 0,600 9.,00.9,00 9.,900.,000. 7,00. 0 single PS 00 0,00 6.6,00.,600.,900.6, ,00.7 single EM 00 7,000 7.,00.,000 6.,00.8 9,00 9.7, single PS 00 6,00.,00.0,600.,00. 8,900 7.,00.6 single EM 800 6, ,800. 7,000 6., ,800 9., single PS 800 6, ,800. 7,700.6,00. 66,800 8.,00.7 single EM , ,00. 79, ,00. 7,00 8., single PS ,600. 8, , ,00.0 7,00 7.,000. ooling capacities based upon 80.6 F DB, 66. F WB entering air temperature //08 Heating capacities based upon 68 F DB, 9 F WB entering air temperature All ratings based upon 08V operation WaterFurnace works continually to improve its products. As a result, the design and specifications of each product at the time of order may be changed without notice. Please contact WaterFurnace at for latest design and SD8 0/08 Page of

5 -6 Tons 60Hz Fan Performance Data - PS Standard PS Motor Fan Blower Motor Airflow (cfm) at External Static Pressure (in. wg) Model Spd Size HP H M 9 x 7 / L H M 9 x 7 / L H M 9 x 7 / L H M 0 x 0 / L H M 0 x 0 / L H M x L H M x L Optional High Static PS Motor Fan Blower Motor Airflow (cfm) at External Static Pressure (in. wg) Model Spd Size HP H M 9 x 7 / L H M 9 x 7 / L H M 9 x 7 / L H M 0 x 0 / L H M 0 x 0 / L Factory settings are in Bold High-Static option not available for 060 and 070 Air flow values are with dry coil and standard filter For wet coil performance first calculate the face velocity of the air coil (Face Velocity [fpm] = Airflow [cfm] / Face Area [sq ft]). Then for velocities of 00 fpm reduce the static capability by 0.0 in. wg, 00 fpm by 0.08 in. wg, 00 fpm by 0.in. wg. WaterFurnace works continually to improve its products. As a result, the design and specifications of each product at the time of order may be changed without notice. Please contact WaterFurnace at for latest design and SD8 0/08 Page of

6 -6 Tons 60Hz Fan Performance Data - EM Single Speed MODEL MAX AI FLOW DIP SWITH SETTINGS ESP L L M L M H M H H w/hp* L M H L M H w/hp* L M H L M H w/hp* L M H L L M M H H Factory settings are at recommended L-M-H DIP switch locations M-H settings MUST be located within boldface FM range Lowest and Highest DIP switch settings are assumed to be L and H respectively Dual apacity FM is controlled within ±% up to the maximum ESP Max ESP includes allowance for wet coil and standard filter MODEL MAX AI FLOW DIP SWITH SETTINGS ESP L L M M H H w/hp* L M H L M H w/hp* L M H L L M M H H Factory settings are at recommended L-M-H DIP switch locations M-H settings MUST be located within boldface FM range Lowest and Highest DIP switch settings are assumed to be L and H respectively FM is controlled within ±% up to the maximum ESP Max ESP includes allowance for wet coil and standard filter /0/06 /0/06 A -position DIP switch package on the control allows the airflow levels to be set for low, medium, and high speed when using the EM blower motor. Only three of the DIP switches can be in the "on" position. The first "on" switch (the lowest position number) determines the low speed fan setting. The second "on" switch determines the medium speed fan setting. The third "on" switch determines the high speed fan setting. The example to the right shows SW on the control board configured for the following 0 airflow settings. Low Speed Fan: 900 FM Medium Speed Fan: 0 FM High Speed Fan: 0 FM Off SW On WaterFurnace works continually to improve its products. As a result, the design and specifications of each product at the time of order may be changed without notice. Please contact WaterFurnace at for latest design and SD8 0/08 6 Page of

7 -6 Tons 60Hz Physical Data (Single Speed) Model SINGLE SPEED ompressor ( each) opeland Scroll Factory harge 0a, oz [kg] Vertical 6 [.76] 6 [.76] 8 [.] 8 [.] 98 [.78] 0 [.] 6 [.] Factory harge 0a, oz [kg] Horizontal 60 [.70] 66 [.87] 8 [.] 8 [.] 98 [.78] 9 [.67] [.6] Fan Motor & Blower oax and Water Piping EM PS EM Variable Speed PS Speeds EM / [7] / [7] / [7] / [7] / [7] [76] [76] PS / [9] / [9] / [7] / [7] / [7] [76] [76] EM PS 9 x 7 [9 x 78] 9 x 7 [9 x 78] 9 x 7 [9 x 78] 9 x 7 [9 x 78] x 0 [79 x ] 0 x 0 [ x ] x 0 [79 x ] 0 x 0 [ x ] x 0 [79 x ] 0 x 0 [ x ] x 0 [79 x ] x 0 [79 x ] x 0 [79 x ] x 0 [79 x ] Water onnections Size - Swivel - in [mm] " [.] " [.] " [.] " [.] " [.] " [.] " [.] HWG onnection Size - Swivel - in [mm] " [.] " [.] " [.] " [.] " [.] " [.] " [.] oax & Piping Water Volume - gal [l] 0.7 [.6].0 [.8]. [.9]. [.9].6 [6.].6 [6.]. [8.7] Vertical Fan Motor Type/Speeds Fan Motor- hp [W] Blower Wheel Size (Dia x W), in. [mm] Air oil Dimensions (H x W), in. [mm] 8 x 0 [7 x ] 8 x 0 [7 x ] 8 x [7 x 6] x [8 x 6] x [8 x 6] 6 x [9 x 6] 6 x [9 x 6] Air oil Total Face Area, ft [m].9 [0.6].9 [0.6].9 [0.].6 [0.70].6 [0.70] 6. [0.6] 6. [0.6] Air oil Tube Size, in [mm] /8 [9.] /8 [9.] /8 [9.] /8 [9.] /8 [9.] /8 [9.] /8 [9.] Air oil Number of rows Filter Standard - " [mm] Pleated MEV Throwaway, in [mm] 8 x [7 x 60] 8 x [7 x 60] 8 x 0 [7 x 76] x 0 [8 x 76] x 0 [8 x 76] 6 x 0 [9 x 76] 6 x 0 [9 x 76] Weight - Operating, lb [kg] 0 [8] 0 [] 6 [66] 80 [7] 0 [90] [06] 80 [8] Weight - Packaged, lb [kg] [] 0 [0] 7 [70] 90 [77] 0 [9] 6 [] 90 [] Horizontal Air oil Dimensions (H x W), in. [mm] 8 x 0 [7 x 76] 8 x 0 [7 x 76] 0 x [08 x 889] 0 x 0 [08 x 06] 0 x 0 [08 x 06] 0 x [08 x ] 0 x [08 x ] Air oil Total Face Area, ft [m].9 [0.6].9 [0.6].9 [0.].6 [0.70].6 [0.70] 6. [0.6] 6. [0.6] Air oil Tube Size, in [mm] /8 [9.] /8 [9.] /8 [9.] /8 [9.] /8 [9.] /8 [9.] /8 [9.] Air oil Number of rows Filter Standard - " [mm] Pleated MEV Throwaway, in [mm] - 8 x [7 x 8] - 8 x [7 x 8] - 0 x 7 [686 x 90] - 0 x 0 [08 x 08] - 0 x [08 x 9] - 0 x 0 [08 x 08] - 0 x [08 x 9] - 0 x [08 x 6] - 0 x [08 x 9] - 0 x [08 x 6] - 0 x [08 x 9] Weight - Operating, lb [kg] 07 [9] [6] 70 [68] 8 [7] [9] 60 [09] 8 [0] Weight - Packaged, lb [kg] [6] 7 [] 8 [7] 00 [8] 0 [00] 7 [] 00 [7] Notes: Sizes 06, 0, 08 available with HP blower motor. (EM only) /9/07 WaterFurnace works continually to improve its products. As a result, the design and specifications of each product at the time of order may be changed without notice. Please contact WaterFurnace at for latest design and SD8 0/08 7 Page of

8 -6 Tons 60Hz Physical Data (Dual apacity) ompressor ( each) DUAL APAITY opeland -speed Scroll, UltraTech Factory harge 0a, oz [kg] Vertical 6 [.76] 78 [.] 89 [.] [.6] 0 [.97] Factory harge 0a, oz [kg] Horizontal 60 [.70] 76 [.6] 89 [.] [.] 60 [.] EM Fan Motor & Blower Fan Motor Type/Speeds EM Variable Speed Fan Motor- hp [W] / [7] / [7] / [7] [76] [76] Blower Wheel Size (Dia x W), in. [mm] oax and Water Piping 9 x 7 [9 x 78] x 0 [79 x ] x 0 [79 x ] x 0 [79 x ] x 0 [79 x ] Water onnections Size - Swivel - in [mm] " [.] " [.] " [.] " [.] " [.] HWG onnection Size - Swivel - in [mm] " [.] " [.] " [.] " [.] " [.] oax & Piping Water Volume - gal [l] 0.7 [.6]. [.9].6 [6.].6 [6.]. [8.7] Vertical Air oil Dimensions (H x W), in. [mm] 8 x 0 [7 x ] 8 x [7 x 6] x [8 x 6] 6 x [9 x 6] 6 x [9 x 6] Air oil Total Face Area, ft [m].9 [0.6].9 [0.].6 [0.70] 6. [0.6] 6. [0.6] Air oil Tube Size, in [mm] /8 [9.] /8 [9.] /8 [9.] /8 [9.] /8 [9.] Air oil Number of rows Filter Standard - " [mm] Pleated MEV Throwaway, in [mm] 8 x [7 x 60] 8 x 0 [7 x 76] x 0 [8 x 76] 6 x 0 [9 x 76] 6 x 0 [9 x 76] Weight - Operating, lb [kg] 0 [8] 70 [68] 0 [90] 6 [] 80 [8] Weight - Packaged, lb [kg] [] 80 [7] 0 [9] 7 [] 90 [] Horizontal Model Air oil Dimensions (H x W), in. [mm] 8 x 0 [7 x 76] 0 x [08 x 889] 0 x 0 [08 x 06] 0 x [08 x ] 0 x [08 x ] Air oil Total Face Area, ft [m].9 [0.6].9 [0.].6 [0.70] 6. [0.6] 6. [0.6] Air oil Tube Size, in [mm] /8 [9.] /8 [9.] /8 [9.] /8 [9.] /8 [9.] Air oil Number of rows Filter Standard - " [mm] Pleated MEV Throwaway, in [mm] - 8 x [7 x 8] - 0 x 7 [686 x 90] - 0 x 0 [08 x 08] - 0 x [08 x 9] - 0 x [08 x 6] - 0 x [08 x 9] - 0 x [08 x 6] - 0 x [08 x 9] Weight - Operating, lb [kg] 07 [9] 7 [70] [9] 70 [] 8 [0] Weight - Packaged, lb [kg] [6] 90 [77] 0 [00] 8 [0] 00 [7] Notes: Sizes 08, 09 available with HP blower motor (EM only). /9/07 WaterFurnace works continually to improve its products. As a result, the design and specifications of each product at the time of order may be changed without notice. Please contact WaterFurnace at for latest design and SD8 0/08 8 Page of

9 -6 Tons 60Hz Unit Electrical Data Single speed with EM motor Model * 0 0* 08 08* Single speed with PS Motor Dual apacity Model ated Voltage *With optional HP EM motor ated Voltage *With optional HP EM motor Voltage MIN/MAX 08-0/60/ 97/ Voltage MIN/MAX 08-0/60/ 97/ ompressor HWG Ext Fan Total Min Max Pump Loop Motor Unit irc Fuse/ M LA LA FLA FLA FLA FLA Amp HA Model HWG Ext Fan Total Min Max ated Voltage ompressor Pump Loop Motor Unit irc Fuse/ Voltage Min/Max M LA LA FLA FLA FLA FLA Amp HA * * * /60/ 97/ * * *With optional over-sized blower /0/ * 09 09* ompressor NOTE: HA circuit breaker in USA only. All fuses lass K- HWG Ext Fan Total Min Max Pump Loop Motor Unit irc Fuse/ M LA LA FLA FLA FLA FLA Amp HA WaterFurnace works continually to improve its products. As a result, the design and specifications of each product at the time of order may be changed without notice. Please contact WaterFurnace at for latest design and SD8 0/08 9 Page of /0/06

10 -6 Tons 60Hz Vertical Dimensional Data Top Air Discharge LEFT ETUN IGHT ETUN Q P O Q L O M L N N TOP TOP.9in [.8cm] T T.9in [.8cm] S S K J I A FONT DEHFG ft [6cm] Primary Service Access B LEFT SIDE B IGHT SIDE Overall abinet Water onnections Electrical Knockouts Discharge onnection eturn onnection Vertical I J K duct flange installed (±0.0 in) using std deluxe filter rack (±0.0 in) Models A B D E F G H Loop /" cond /" cond /" cond L M N O P Q S T Width Depth Height* In Out HWG In HWG ond- Low Power Supply Supply eturn eturn Water FPT HWG FPT Ext Pump Out ensate Voltage Supply Width Depth Depth Height 0-00 in " Swivel " Swivel cm in " Swivel " Swivel cm in " Swivel " Swivel cm in " Swivel " Swivel cm ondensate is /" PV female glue socket and is switchable from side to front Vertical unit shipped with deluxe " (field adjustable to ") duct collar/filter rack extending from unit." and is suitable for duct connection. Discharge flange is field installed and extends " [. mm] from cabinet Decorative molding and water connections extend." [0.mm] beyond front of cabinet. ev.: 07/9/06 B WaterFurnace works continually to improve its products. As a result, the design and specifications of each product at the time of order may be changed without notice. Please contact WaterFurnace at for latest design and SD8 0/08 0 Page of

11 -6 Tons 60Hz Horizontal Dimensional Data TOP VIEW Q P.in [.cm] MOUNT () HANGE BAKETS AS SHOWN TO ALLOW AESS TO FILTE ft [6cm] Primary Service Access.9in [.8cm] FONT VIEW A S SIDE DISHAGE VIEW B N O L L END VIEW O S M K J I D E F G H AS SHOWN L UNIT ( UNIT ON OPPOSITE SIDE SAME DIMENSIONS) Overall abinet Water onnections Electrical Knockouts Discharge onnection eturn onnection Horizontal I J K duct flange installed (±0.0 in) using std deluxe filter rack (±0.0 in) Models A B D E F G H Loop /" cond /" cond /" cond L M N O P Q S Width Depth Height* In Out HWG In HWG ond- Low Power Supply Supply eturn eturn Water FPT HWG FPT Ext Pump Out ensate Voltage Supply Height Depth Depth Height 0-00 in " Swivel " Swivel cm in " Swivel " Swivel SEE.6. SEE cm HAT.6. HAT in " Swivel " Swivel SEE.6. SEE cm HAT.6. HAT in " Swivel " Swivel SEE.6. SEE cm HAT.6. HAT ev.: 07/8/06 B Units Not Shown Above ight eturn End Discharge ight eturn Side Discharge Left eturn End Discharge Left eturn Side Discharge L O in..8.6 cm in cm.. 7. in cm.. 9. in cm ondensate is /" PV female glue socket and is switchable from side to front Horizontal unit shipped with deluxe " (field adjustable to ") duct collar/filter rack extending from unit.88" and is suitable for duct connection. Discharge flange is field installed and extends " [. mm] from cabinet Decorative molding and water connections extend." [0.mm] beyond front of cabinet. WaterFurnace works continually to improve its products. As a result, the design and specifications of each product at the time of order may be changed without notice. Please contact WaterFurnace at for latest design and SD8 0/08 Page of

12 -6 Tons 60Hz Vertical Dimensional Data Bottomflow LEFT ETUN IGHT ETUN.70 (. cm) S S T T K J I D E F G B LEFT SIDE Q B IGHT SIDE Q.90 (.7 cm) L A FONT H ft [6cm] Primary Service Access O N L M N O P LEFT BOTTOM DISHAGE FLOO FOOT PINT IGHT BOTTOM DISHAGE FLOO FOOT PINT Bottomflow Models Overall abinet Water onnections Electrical Knockouts Discharge onnection eturn onnection duct flange installed (±0.0 in) using std delux e filter rack (±0.0 in) I J K A B D E F G H /" cond /" cond /" cond Loop L M N O P Q S T HWG Low Power Supply Supply eturn eturn Width Depth Height In Out HWG In HWG Out ondensate Water FPT Ex t Pump FPT Voltage Supply Width Depth Depth Height in " Swivel " Swiv el c m in " Swivel " Swiv el cm ondensate is /" PV female glue socket and is switchable from side to front ev.: 09/7/07 Vertical bottomflow unit shipped with deluxe " (field adjustable to ") duct collar/filter rack extending from unit." and is suitable for duct connection. Decorative molding and water connections extend." (0.mm) beyond front of cabinet. WaterFurnace works continually to improve its products. As a result, the design and specifications of each product at the time of order may be changed without notice. Please contact WaterFurnace at for latest design and SD8 0/08 Page of

13 W O G G Y W O G G T T IN IN ontractor: -6 Tons 60Hz Fold and mate arrows G Envision - Single Speed Wiring Schematic /60/ Fold and mate arrows Auxiliary Electric Heat Power 08-0/60/ Y With optional ' EA' Series Auxiliary ElectricHeat Typical schematic shown 97P //08 L L NOTE G L L L L G P9 F Unit Power 08-0/60/ 8 PB Ext Pump / hp Total 08-0/60/ Grn Pump Pump Brn NOTE L L Or P8 P Brn Brn Blk/Wht() Pink Pink Org Yel O G Yel W -- Org Gry/Wht(0) Blu Blk -- Blk DHW Pump Gray Gray -- NOTE Gry(9) PB Yel(8) Blk S un apacitor ed Black Blue omfort Alert Tan (6) PS Blk Pink Brn() Org() Pink NOTE 6 A Fuse E Gray Yel Pink() Y L PS Fan Motor Brn ap Wht Grn P Wht H M L Blk P Blu(7) T G Wiring Schematics /60/ - PS ontact waterfurnace.com for additional wiring schematics Gray NO Blu 0V ed 08V 0V L 0V L 0V L Fused L Fused L Gray E F-0A 0V HE TS Gray P7 Transformer NO NO Blk Blk NO N NO N NO V Blk HE TS Yel E Blk/Wh Yel Yel Yel F-0A 0V OM OM OM OM HE TS Pink NO Blk(7) Yel(6) Blk() Pink omfort Alert HE TS Pink E HI Violet() P6 Not Used Violet() NO P P Black -GND Blk() Violet P Thermostat EA Series PB 6 6 Yellow P0 0 Blue Gray Y O Brown Y Not Used P0 Not Used Orange Orange 0 Premier Microprocessor Logic ontrol (D Voltage) Y Y Blue Blue LO Pink L Pink NOTE 9 White White Tan Tan P ed ed Shut Not Used Down 6 EM Air Flow NOTE SA installed units only Local codes may require a single Settings E-Series Logic Board - Physical Layout NOTE P source of power supply SL In SL In L omfort Alert Tan On SW On SW On SW Single Disconnect Power 08-0/60/ omfort Alert Physical Layout 0V - L 0V - L Fused L Fused L Fused L Fused L Fused L 0V - L 0V - L SL Out Speed / Speed SL Out Not Optional Orange V POWE Orange Legend Breaker box L L F F furnished by Not Used Factory Low voltage wiring Thermistor installer Not Used Factory Line voltage wiring N.. Pink Field low voltage wiring Light emitting diode - Green N.O. N.O. N.O. N.O. Data Port HWL Field line voltage wiring Pink Optional block elay coil om om Yellow D Voltage PB traces FP Internal junction apacitor w/ bleed resistor ircuit Breakers - DHW - Loop Yellow Quick connect terminal Pump Pump - - Blue Switch - ondensate overflow LP Wire nut Premier Logic Board L L L L Blue D Switch - High pressure -GND Sol 0 Black L Field wire lug HP Switch - Low pressure LO ALET Black Ground Aux Elect Power Unit Power HI TIP elay ontacts- 08-0/60/ 08-0/60/ Switch -Hot Water On/Off P6 N.O., N.. Microprocessor omfort Alert Status Fuse Polarized connector Notes: LED Flash ode Description Switch Blue and ed wires for 08V operation. - onnection of remote unit that does not have a loop pump for slave operation. Green Solid Module Has Power SW SW SW 6 - V Accessory relay (see SW - for description of operation ) ed Solid Y Present But ompressor Not unning A - omfort Alert Off On Off On Off On ode Long un Time - ompressor ontactor LP - Low pressure switch - The blk/wh and gray/wh wires are removed when Aux Heat is installed. - Buss lugs L and L can be removed and dual power wire sets connected directly to box lugs L, L, ode System Pressure Trip O - ondensate overflow sensor PB, PB - Power blocks and L, L. - DHW pump relay PS - Power strip ode Short ycling DHW pump only in models with hot water generation option. - Loop pump relay V - eversing Valve coil ode Locked otor 7 This Switch allows the unit to down stage with the t -stat when OFF and finish on second stage when - PS Fan Speed elay SW - DIP package position P ON. Finish second stage reduces stage changing in recip dual capacity compressors and should Yellow ode Open ircuit - PS Fan Power elay SW - DIP package 8 position be ON for unzoned Dual ap E -Series or Premier speed units. 8 ode 6 Open Start ircuit S - ompressor Solenoid SW - DIP package position 8 SW- should be in the OFF position when using the 7P0A0 electric heat board and 9 ode 7 Open un ircuit 0 should be ON when using the 7PA0 electric heat board. F and F - Fuses SW - Hot water pump enable switch ode 8 Welded ontactor 9 SW-8 must be in the OFF position for pulsed L lockout signal and in the ON position for constant FP - Freeze protection sensor TS - Thermal limit switch L lockout signal. ode 9 Low Voltage HE - Heater element HWL - Hot water limit sensor P P P 0 - When optional electronic air -filter is installed, power for the electronic air-filter is provided by P - and HP - High pressure switch S - Start ontactor P VA. E to E - Aux heat stage relays S - Start elay omfort Alert fault output to Premier ontrol Board Shut SL SL SL SL A A A Y Y W O G L Down Out Out NO N OM Normal / Finish on nd (Note 7) No PM / PM Test / Norm Loop / Well Fan / omp Used Dehum / Norm 0 Electric Heat / Normal (Note 8) Envision / E Series or Premier emote Unit Without Loop Pump No Htg / Htg NOTE Inputs / Norm Outputs / Norm Pulse L / onstant L (NOTE 9) P Acc om Acc N Acc NO NOTE 0 Optional Electronic Air-Filter 0 Main Logic PB P Diagnostic Modes Outputs Outputs Inputs urrent Fault Status LED Normal Display Mode #6 Off, #7 Off Blower Lo #6 On, #7 Off ompressor Lo #6 Off, #7 On Y # Off, #6 On, #7 On Drain pan overflow Field Selection Dips - # On, #6 On, #7 On Drain pan overflow Lockout Drain Blower Med Blower Hi Aux Heat # ompressor Hi V FAN Y FP thermistor (loop< F, well<0 F) High Pressure Low Pressure / omfort Alert FP thermistor (loop< F,well<0 F) Lockout High Pressure Low Pressure / omfort Alert Water Flow High Press Low Press / A Status LED PB Aux Heat # AuxHeat # Aux Heat # DHW Pump Loop Pump Loop Pump SL SL EM PM < 00 rpm Not Used HWL thermistor > 0 F EM PM < 00 rpm Lockout Microprocessor malfunction * HWL thermistor > 0 F Air Flow Status DHW Limit SW DHW pump switch off DHW pump switch off DHW off *Green LED not flashing Fold and mate arrows Fold and mate arrows WaterFurnace works continually to improve its products. As a result, the design and specifications of each product at the time of order may be changed without notice. Please contact WaterFurnace at for latest design and SD8 0/08 Page of

14 W O G G Y W O G G T T P T G IN IN ontractor: -6 Tons 60Hz Fold and mate arrows Fold and mate arrows Auxiliary Electric Heat Power 08-0/60/ With optional ' EA' Series Auxiliary ElectricHeat Typical schematic shown L L NOTE G G L L L L G P9 F Unit Power 08-0/60/ Y PB Ext Pump / hp Total 08-0/60/ Grn Pump Pump Brn NOTE L L Or P8 Brn Brn 8 Blk/Wht() Pink Pink Blu Yel Yel Violet Org Org Gry/Wht(0) 8 Blu Blk Blk Gray Gray NOTE DHW Pump Gry(9) PB Yel(8) Blk PS Blk O G Pink W Brn() -- Org() Pink NOTE 6 A Fuse -- E Gray -- Yel Grn Grn S Pink() un apacitor Blu(7) Gray NO Blu 0V ed Black Blue omfort Alert Tan (6) ed 08V P 0V L 0V L 0V L P Fused L Fused L Gray Y E L F-0A 0V HE TS Wiring Schematic /60/ - EM ontact waterfurnace.com for additional wiring schematics Gray P7 EM Transformer EM NO NO Blk Blk NO N NO N NO Fan Motor Fan Motor V Blk HE TS Yel E Blk/Wh Yel Yel Yel F-0A 0V OM OM OM OM HE TS Pink NO PM grnd PWM PM On/Off Fused L Blk(7) Yel(6) Blk() Pink PM grnd PWM PM On/Off omfort Alert P 6 0 HE TS Pink E P 6 0 HI Violet() P6 Not Used Violet() NO P Black Black -GND Blk() Violet Violet Yellow P Thermostat EA Series PB 6 Yellow P0 Blue Blue Gray Gray Y O Brown Y Not Used P0 Not Used Orange Orange 0 Premier Microprocessor Logic ontrol (D Voltage) Y Y Blue Blue LO Pink L Pink White White Tan Tan P NOTE 9 ed ed Shut Not Used Down 6 EM Air Flow NOTE SA installed units only Local codes may require a single Settings E-Series Logic Board - Physical Layout P NOTE 7 NOTE source of power supply SL In SL In L omfort Alert Tan On SW On SW On SW Single Disconnect Power 08-0/60/ omfort Alert Physical Layout 0V - L 0V - L Fused L Fused L Fused L Fused L Fused L 0V - L 0V - L SL Out Speed / Speed SL Out Optional Orange V POWE Orange Breaker box L L F F furnished by Not Used Factory Low voltage wiring Thermistor Factory Line voltage wiring installer Not Used Field low voltage wiring Light emitting diode - Green N.. Field line voltage wiring N.O. N.O. N.O. N.O. Data Pink Port HWL Optional block elay coil Pink D Voltage PB traces Internal junction apacitor w/ bleed resistor om om Yellow FP Quick connect terminal ircuit Breakers - DHW - Loop Yellow Switch - ondensate overflow Pump Pump - - Blue Wire nut LP Switch - High pressure Premier Logic Board L L L L Blue D L Field wire lug -GND Sol Switch - Low pressure 0 Black HP Ground ALET Black LO Aux Elect Power Unit Power elay ontacts- TIP Switch -Hot Water On/Off HI N.O., N /60/ 08-0/60/ P6 Microprocessor Fuse Polarized connector omfort Alert Status Notes: Switch Blue and ed wires for 08V operation. LED Flash ode Description - onnection of remote unit that does not have a loop pump for slave operation. Green Solid Module Has Power A - omfort Alert SW SW SW 6 - V Accessory relay (see SW - for description of operation ) ed Solid Y Present But ompressor Not unning - ompressor ontactor LP - Low pressure switch Off On Off On Off On O - ondensate overflow sensor PB, PB - Power blocks - The blk/wh and gray/wh wires are removed when Aux Heat is installed. ode Long un Time - Buss lugs L and L can be removed and dual power wire sets connected directly to box lugs L, L, ode System Pressure Trip - DHW pump relay PS - Power strip and L, L. - Loop pump relay V - eversing Valve coil ode Short ycling - PS Fan Speed elay SW - DIP package position DHW pump only in models with hot water generation option. ode Locked otor 7 - Air Flow onfiguration Example : SW configured for dip as low, dip as medium, and dip as high - PS Fan Power elay SW - DIP package 8 position P Speed EM fan Yellow ode Open ircuit F and F - Fuses SW - DIP package position 8 8 SW- should be in the OFF position when using EM motor and 7P0A0 electric heat board and ode 6 Open Start ircuit FP - Freeze protection sensor SW - Hot water pump enable switch 9 should be ON when using EM with 7PA0 electric heat board ode 7 Open un ircuit HE - Heater element TS - Thermal limit switch 0 9 SW-8 must be in the OFF position for pulsed L lockout signal and in the ON position for constant ode 8 Welded ontactor HP - High pressure switch HWL - Hot water limit sensor L lockout signal. ode 9 Low Voltage E to E - Aux heat stage relays S - Start ontactor P 0 - When optional electronic air -filter is installed, power for the electronic air-filter is provided by P - and S - ompressor Solenoid S - Start elay P P P VA omfort Alert fault output to Premier ontrol Board This Switch allows the unit to down stage with the t -stat when OFF and finish on second stage when Shut SL SL SL SL A A A Y Y W O G L ON. Finish second stage reduces stage changing in recip dual capacity compressores and should Down Out Out NO N OM be ON for unzoned Dual ap E -Series or Premier speed units. Legend Normal / Finish on nd (Note ) No PM / PM Test / Norm Loop / Well Fan / omp Not Used 0 Old EH & EM / Normal (Note 8) Envision / E Series or Premier Dehum / Norm emote Unit Without Loop Pump No Htg / Htg NOTE Inputs / Norm Outputs / Norm Pulse L / onstant L P Acc om Acc N Acc NO NOTE 0 Optional Electronic Air-Filter 0 Main Logic PB P Diagnostic Modes Outputs Outputs Inputs urrent Fault Status LED Normal Display Mode #6 Off, #7 Off Blower Lo #6 On, #7 Off ompressor Lo #6 Off, #7 On Y # Off, #6 On, #7 On Drain pan overflow Field Selection Dips - # On, #6 On, #7 On Drain pan overflow Lockout Drain Blower Med Blower Hi Aux Heat # ompressor Hi V FAN Y FP thermistor (loop< F, well<0 F) High Pressure > 600 PSI Low Pressure < 0 PSI FP thermistor (loop< F,well<0 F) Lockout High Pressure > 600 PSI Lockout Low Pressure < 0 PSI Lockout Water Flow High Press Low Press / omp Status LED PB Aux Heat # AuxHeat # Aux Heat # DHW Pump Loop Pump Loop Pump SL SL EM PM < 00 rpm Not Used HWL thermistor > 0 F EM PM < 00 rpm Lockout Microprocessor malfunction * HWL thermistor > 0 F Air Flow Status DHW Limit SW DHW pump switch off DHW pump switch off DHW off *Green LED not flashing Fold and mate arrows Fold and mate arrows 97P77-0 8/9/06 WaterFurnace works continually to improve its products. As a result, the design and specifications of each product at the time of order may be changed without notice. Please contact WaterFurnace at for latest design and SD8 0/08 Page of

15 -6 Tons 60Hz Pressure Drop Single Speed Models Dual apacity Models Model GPM Pressure Drop (psi) 0 F 0 F 70 F 90 F 0 F Model GPM Pressure Drop (psi) 0 F 0 F 70 F 90 F 0 F full load part load full load part load full load /0/06 09 part load 06 full load part load full load part load /0/06 WaterFurnace works continually to improve its products. As a result, the design and specifications of each product at the time of order may be changed without notice. Please contact WaterFurnace at for latest design and SD8 0/08 Page of

16 -6 Tons 60Hz orrection Factor Tables Part Load Air Flow orrections Airflow ooling Heating FM Per % of Heat of Heat of Total ap Sens ap Power Htg ap Power Ton of lg Nominal ej Ext Full Load Air Flow orrections Airflow ooling Heating FM Per % of Heat of Heat of Total ap Sens ap Power Htg ap Power Ton of lg Nominal ej Ext ooling apacity orrections (Dual apacity Full & Part Load; Single Speed) Entering Total Sensible ooling apacity Multipliers - Entering DB ºF Power Heat of Air WB ºF lg ap Input ejection * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * Note: * Sensible capacity equals total capacity at conditions shown. 7/0/06 /0/06 /0/06 Heating apacity orrections (Dual apacity Full & Part Load; Single Speed) Heating orrections Ent Air DB F Htg ap Power Heat of Ext /0/06 WaterFurnace works continually to improve its products. As a result, the design and specifications of each product at the time of order may be changed without notice. Please contact WaterFurnace at for latest design and SD8 0/08 6 Page of

17 -6 Tons 60Hz orrection Factor Tables - (cont.) Antifreeze Type Antifreeze % by wt ooling apacity Heating apacity Pressure Drop EWT - degf [Deg] 90 [.] 0 [-.] 0 [-.] Water Ethylene Glycol Propylene Glycol Ethanol Methanol Warning: Gray area represents antifreeze concentrations greater than % by weight and should be avoided due to the extreme performance penalty they represent. WaterFurnace works continually to improve its products. As a result, the design and specifications of each product at the time of order may be changed without notice. Please contact WaterFurnace at for latest design and SD8 0/08 7 Page of

18 -6 Tons 60Hz NS0 - Single Speed - PS apacity Data (700 FM) NSV0 single speed PS Motor 700 ated FM Heating 700 ated FM ooling Performance capacities shown in thousands of Btuh. EWT F WPD HEATING - EAT 70 F OOLING - EAT 80/67 F Flow gpm HW HW PSI FT EAT H kbtuh Power kw HE kbtuh LAT F OP EAT T kbtuh S kbtuh S/T atio Power kw H kbtuh EE kbtuh kbtuh / / / / / / / / / / / / / / / / / / / / / / / / / WaterFurnace works continually to improve its products. As a result, the design and specifications of each product at the time of order may be changed without notice. Please contact WaterFurnace at for latest design and SD8 0/08 8 Page of

19 -6 Tons 60Hz NS00 - Single Speed - PS apacity Data (900 FM) NSV00 single speed PS Motor 900 ated FM Heating 900 ated FM ooling Performance capacities shown in thousands of Btuh. EWT F Flow gpm WPD HEATING - EAT 70 F OOLING - EAT 80/67 F HW PSI FT EAT H kbtuh Power kw HE kbtuh LAT F OP EAT T kbtuh S kbtuh S/T atio Power kw H kbtuh EE kbtuh / / / / / / / / / / / / / / / / / / / / / / / / / HW kbtuh WaterFurnace works continually to improve its products. As a result, the design and specifications of each product at the time of order may be changed without notice. Please contact WaterFurnace at for latest design and SD8 0/08 9 Page of

20 -6 Tons 60Hz NS06 - Single Speed - PS apacity Data (0 FM) NSV06 single speed PS Motor 0 ated FM Heating 0 ated FM ooling Performance capacities shown in thousands of Btuh. EWT F Flow gpm WPD HEATING - EAT 70 F OOLING - EAT 80/67 F HW PSI FT EAT H kbtuh Power kw HE kbtuh LAT F OP EAT T kbtuh S kbtuh S/T atio Power kw H kbtuh EE kbtuh / / / / / / / / / / / / / / / / / / / / / / / / / HW kbtuh WaterFurnace works continually to improve its products. As a result, the design and specifications of each product at the time of order may be changed without notice. Please contact WaterFurnace at for latest design and SD8 0/08 0 Page of

21 -6 Tons 60Hz NS0 - Single Speed - PS apacity Data (0 FM) NSV0 single speed PS Motor 0 ated FM Heating 0 ated FM ooling Performance capacities shown in thousands of Btuh. EWT F Flow gpm WPD HEATING - EAT 70 F OOLING - EAT 80/67 F HW PSI FT EAT H kbtuh Power kw HE kbtuh LAT F OP EAT T kbtuh S kbtuh S/T atio Power kw H kbtuh EE kbtuh / / / / / / / / / / / / / / / / / / / / / / / / / HW kbtuh WaterFurnace works continually to improve its products. As a result, the design and specifications of each product at the time of order may be changed without notice. Please contact WaterFurnace at for latest design and SD8 0/08 Page of

22 -6 Tons 60Hz NS08 - Single Speed - PS apacity Data (00 FM) NSV08 single speed PS Motor 00 ated FM Heating 00 ated FM ooling Performance capacities shown in thousands of Btuh. EWT F Flow gpm WPD HEATING - EAT 70 F OOLING - EAT 80/67 F HW PSI FT EAT H kbtuh Power kw HE kbtuh LAT F OP EAT T kbtuh S kbtuh S/T atio Power kw H kbtuh EE kbtuh / / / / / / / / / / / / / / / / / / / / / / / / / HW kbtuh WaterFurnace works continually to improve its products. As a result, the design and specifications of each product at the time of order may be changed without notice. Please contact WaterFurnace at for latest design and SD8 0/08 Page of