DIGITAL VIDEO RECORDER INSTRUCTION MANUAL VER J1.2

Transcription

1 DIGITAL VIDEO RECORDER INSTRUCTION MANUAL VER J Unit Description (1) Front Panel ) REMOVABLE HARD DISK DRIVE BAY 2) PLAY / STOP / FAST REWIND / FAST FORWARD / RECORD / POWER From left to right: PLAY/REVERSE playback button This button is used to start the playback of recorded data. By default, the playback starts from the earliest recording in the storage device. STOP This button stops recording or playback. FAST REWIND / LOCK This button is used to fast rewind during playback. It also locks all buttons on the Digital Video Recorder along with the remote controller. The LOCK LED light is turned on when this feature is activated. To unlock, press the lock button again and enter the password when prompted. The DVR cannot be locked in playback mode. FAST FORWARD / SWAP / PTZ This button is used to fast forward during playback. It is also used as the Pan, Tilt and Zoom submenu in live mode. Press and hold the button to activate the hard drive hot swappable mode button. RECORD

2 This button starts recording. POWER This button turns the Digital Video Recorder on or off. 3) STATUS INDICATOR Five LEDs display the status of the Digital Video Recorder. From the left, Power (red), Recording (red), Scheduled Recording (green), Button Lock (green) and Network. 4) IR RECEIVER Do not block the receiver as the remote controller needs the line of sight to the receiver. 5) Menu Setup/Search ENTER / +10 This button selects and enables the configuration changes made on the menu and sub-menu screens. It is also used to enter numbers greater than 10 when entering numeric entries or motion grid selection. DISPLAY / UP This button is used to switch between quad view mode and picture-in-picture display mode. It is also used to navigate up in some menus. CANCEL/OSD OFF This button cancels any selection changes in submenus. In Zoom mode, pressing this button will exit to the original display screen. In the regular display screen, this button is used to hide the On-Screen-Display information such as time, date and channel icons. This button also removes any of the alert icons on the upper right corner of the screen (AL, VL and PL). This button is also used to turn off the alarm buzzer. ZOOM/LEFT This button allows to digitally zoom into a specific area in both live and playback screen. Press the button to display the zoom area box, use the arrow keys to move the box, and then press the Enter button again to enlarge the selected area. It is also used to navigate left in some menus. MENU This button accesses the main menu. It is also used to save and for any menu screens. INFO/RIGHT This button displays system information screen: USB device, internal HDD size, Boot-Rom version, Application version, host name and IP address. Press this button once more to access the system log. TIME SEARCH This button accesses the time search menu. Use the directional buttons to select the date and the time. Press this button again to start the playback of the selection. BACKUP/DOWN This button allows back up of video clips onto USB 1.1 compliant memory sticks. If there are no backup devices present, this button is disabled automatically. ALARM SEARCH This button accesses the alarm search menu. Use the directional buttons to select the date and the time. Press this button again to start the playback of the selection. 6) USB PORT USB compliant port allows use of memory sticks to backup video files. 7) NUMERIC BUTTONS (1~9, 10/0)

3 These buttons have a number of functions to enter data and to make selections. They are used to enter numerical data when prompted for the password, to make channel/camera selection, to choose the day in schedule option, and to enter alphabets to label each channel. 2. Basic Operation Press the Power key to turn on the DVR. Press the Record key to start recording. Press the Record key to stop recording. Then press the Power key to turn off the DVR. (password protected) 3. Main Screen 1. DVR STATUS ICON Displays recording mode and playback icons. 2. AUDIO PLAYBACK ICON 3. QUAD MODE ICON Displayed when recording in quad mode. 4. BACKUP IN PROGRESS ICON Displayed if backup is in progress. 5. LOCK ICON Displayed when the DVR is locked by pressing the lock button. 6. NETWORK CONNECTIVITY STATUS ICON Displays the number of clients connected to the DVR.

4 7. USB DEVICE STATUS ICON Displayed when a memory stick is inserted into the USB 1.1 port. 8. POWER LOSS ALERT Displayed when there was an interruption in the power supply. The power loss warning icon is displayed after the power comes back on. If an address was entered under the network setup menu, an will be sent when the DVR is powered on again. 9. VIDEO LOSS ALERT Displayed when the video signal is interrupted for any reason from the DVR. If an address was entered under the network setup menu, an will be sent after each occurrence. The DVR checks for the integrity of the video signals every time the record button is pressed and continuously while the DVR is in recording mode. 10. ALARM ALERT Displayed when the alarm is triggered. If an address was entered under the network setup menu, an will be sent after each occurrence. 11. MOTION RECORDING Displayed when recording with motion detection. 12. CHANNEL ICONS Displays the current status of each channel: 1) The channel icon will turn red when the channel is recording. 2) The channel icon will blink when alarm is triggered or motion is detected. 3) The channel icon remains black when the channel is not recording. 13. DATE Displays the current date in mm/dd/yyyy format 14. DAY Displays the current day. 15. TIME Displays the current time in dd/hh/mm/ss format in 24 hour format. 16. REMAINING HARD DRIVE SPACE Displays the remaining hard drive storage space in gigabytes. If the hard drive overwrite is set to on, the counter will remain as 0 and the DVR will continue to write on to the hard drive from the beginning. The counter will remain 0 as long as the hard drive is full with previously recorded data, and will display its original size once the hard drive is formatted.

5 4. Main Menu Press the menu button to enter setup menu. Enter password as prompted. Default password: PLAYBACK (Time search Date & Time Search) 1) Press the Time search button to display the TIME SEARCH menu. Use the arrow buttons to move the cursor to indicate time zone you wish to search. 1) Select the Month and Date where recorded data file exists. The colored bar displays recorded data. Each page displays up to 10 days. To go to the previous or next pages press the arrow buttons. 2) Press the TIME SEARCH (T-SEARCH) button again to search when the cursor is reached to desired time and date. 3) Then, on the next screen time files are listed in a minute mode. <Note> Time search will not be activated if the cursor is placed at black areas.

6 6. ZOOM 1) Press the ZOOM button to display the Zoom Area Box. 2) Move the box to the desired position using the,,, and buttons. 3) Press the ZOOM button to enlarge the desired area. 4) Press the CANCEL button to exit. <Note> The ZOOM button is not activated when a menu is displayed on the screen and multi display mode.

7 7. BACKUP The DVR s only backup method is through a USB 1.1 compliant memory stick. When a memory stick is connected through the USB port, the backup icon will pop up as shown. After the backup icon has appeared, press the backup button and the backup time set screen will appear prompting the user to enter range of time to be backed up. Enter the numbers as required in 24 hour format, and then press the Enter button to start the backup. Please make sure that the end time does not precede the start time. A tape icon will appear to the left of the backup icon and blink in yellow, signifying that the backup is in session. When finished, the icon will stop blinking and then it will disappear.