AFE4403 Watch EVM Factory Firmware Update Procedure
|
|
- Franklin Wood
- 5 years ago
- Views:
Transcription
1 AFE4403 Watch EVM Factory Firmware Update Procedure Page 1
2 The purpose of the document is to provide detailed instructions for updating the AFE4403 Watch firmware to factory default. Table 1 lists the hardware and software tools required to update the firmware on the AFE4403 Watch EVM. Table 1 Required hardware and software tools Hardware / Software Tools Required AFE4403EVM Watch, Qty 1 Specifications or Model Manufacturer Website Small screwdriver, Qty 1 Philips (provided in kit) Tag Connect JTAG cable Tag Connect MSP430 USB-Debug-Interface MSP-FET430UIF Flash Programmers for TI s MSP430 MCU FET430UIF/ ND/ Setup.zip SOFTWARE INSTALLATION 1. Flash Programmer for TI s MSP430 MCUs 1.1. Download the Flash Programmer (FET-Pro430-Lite-Setup.zip) from Elprotronic Website ( Unzip the zipped file to a temp directory and run setup.exe Follow the instructions to install the Flash programmer. Check the option Install USB-Driver for MSP Tools during the installation process as shown in Figure 1. UPGRADE FIRMWARE 1. Setup AFE4403 Watch for JTAG programming Figure1. Install USB-Driver for MSP Tools option 1.1. Verify the AFE4403 Watch EVM is turned off. Flip the watch bottom case facing up as shown in Figure 2. Remove the four screws with screwdriver, holding the top and bottom watch cases together. Figure 2 shows the arrows pointing to the screws to be removed. Page 2
3 Figure 2 Screws to be removed indicated by the arrows When screws have been removed, separate TOP and BOTTOM watch case. Pry gently to separate TOP and BOTTOM watch cases by inserting the screwdriver gently in the opening indicated with arrow shown in Figure 3. Figure 3. Screwdriver insert location to assist watch top and bottom cases separation Figure 4 shows the watch top case separated. Remove the watch board screws as shown in Figure 4 to get access to the JTAG connector on the top side of the AFE4403 Watch EVM. Page 3
4 Figure 4 Board screws to be removed indicated by the arrows 1.4. Figure 5 shows the Tag Connect JTAG footprint. Figure 5 On-Board Tag Connect JTAG footprint 1.5. Slide the switch shown in Figure 6 to ON position to power on the AFE4403 Watch EVM using the battery or connect the microusb cable to the microusb connector and the PC 1.6. Connect the USB cable to the MSP430 USB-Debug-Interface MSP-FET430UIF tool and the PC Connect the Tag Connect cable to the MSP-FET430UIF tool and to the 10-pin JTAG footprint on the AFE4403 Watch EVM. Page 4
5 Figure 6 Slide switch position 1.8. Open the Lite FET-Pro430 software by clicking Start Menu All Programs Elprotronic Flash Programmers 1. Lite FET-Pro430 or from the shortcut icon on the Desktop. Figure 7 Lite FET-Pro430 software 1.9. Click Open Code File -> and select the firmware file for the appropriate sensor board. The firmware is available at SVTronics website ( HRMWatch_v2.2-OSRAM Sensor.txt for OSRAM SFH7050 sensor board HRMWatch_v2.2-NJRC Sensor.txt for NJRC NJL5310R sensor board Select MSP430F5xx and MSP430F5528 under Group for the Microcontroller type. Click on AUTO PROG. to program the firmware as shown in Figure 8. Page 5
6 Figure 8 Lite FET-Pro430 software Firmware select, microcontroller type and auto program The Lite FET-Pro430 software will update the MSP-FET430UIF tool with the latest Flash programmer firmware for the first time. This is a one step process. Click on Start Update and when update is complete, click on Exit as shown in Figure 9 and Figure 10. Figure 9 MSP-FET430UIF start firmware update Page 6
7 Figure 10 MSP-FET430UIF exit firmware update The Report window will show the status of the firmware programming. If programming is successful, DONE message will be displayed in the Report window and Pass will be displayed in the Status box. Figure 11. FET-Pro430 Programmer - Programming Status Page 7
8 1.12. Remove the JTAG cable and slide the switch to the OFF position or remove the microusb cable from the AFE4403 Watch EVM Place the watch board screws back into position as shown in Figure Snap the bottom case to the top case and place the bottom case screws back into position as shown in Figure 2. Page 8
MSP430 Interface to LMP91000 Code Library
Application Note 2230 Vishy Viswanathan July 13, 2012 MSP430 Interface to LMP91000 Code 1.0 Abstract The MSP430 is an ideal microcontroller solution for low-cost, low-power precision sensor applications
More informationMSP430 Interface to LMP91000 Code Library
MSP430 Interface to LMP91000 Code Library 1.0 Abstract The MSP430 is an ideal microcontroller solution for low-cost, low-power precision sensor applications because it consumes very little power. The LMP91000
More informationASSAN ESC PC Interface Software User s Guide
ASSAN ESC PC Interface Software User s Guide Dear customer, Welcome to use ASSAN ESC PC Connector and Interface Software. It allows of the Electronic Speed Controller programming in the desktop PC and
More informationECE 480 Team 5 Introduction to MAVRK module
ECE 480 Team 5 Introduction to MAVRK module Team Members Jordan Bennett Kyle Schultz Min Jae Lee Kevin Yeh Definition of MAVRK Component of MAVRK starter Kit Component of umavrk Module design procedure
More informationTS1 Firmware Update Tool (for PC)
TS1 Firmware Update Tool (for PC) Installation and Operation Quick Start May 1, 2012 Overview This document provides instructions for using the Firmware Update Tool to update a TS1 Keypad to the latest
More informationAFE4404 Demonstration Kit. Message Communication Protocol v4.0
AFE4404 Demonstration Kit Message Communication Protocol for AFE4404 EVM This document describes the message communication protocol for AFE4404 EVM. The message communication protocol applies to AFE4404
More informationMembrane Bezel Kit. Models: T600, T600e, T500, T500e, Speed Scrub 500 and A500
Page1of7 Membrane Bezel Kit Models: T600, T600e, T500, T500e, Speed Scrub 500 and A500 This kit includes the necessary parts to replace a defective membrane bezel control board. Kit installation is required
More informationDelta T Dew Heater for CDK
Delta T Dew Heater for CDK Delta T Dew Heater for CDK12.5 (125902) Your CDK 12.5 Delta T Dew Heater includes the following: QTY 1 Delta T control box w/ mounting bracket attached 1 2.5Amp AC adapter 2
More informationMULTiLOG temperature data logger.
MULTiLOG temperature data logger. Remonsys Ltd, United Kingdom E: info@remonsys.com August 2012 MULTiLOG Installation Guide 1 The MULTiLOG Potential for 16 sensors Serial number and model A flashing red
More informationEPD Extension Kit User Manual
EPD Extension Kit User Manual Date 2013/06/17 Revision 02 Model Name SK014AS0T1, SG020AS0T1, SM027AS0T1 龍亭新技股份有限公司 Pervasive Displays, Inc. No.71, Delun Rd., Rende Dist., Tainan City 71743, Taiwan (R.O.C.)
More informationHV-110 DVB-T HAM TV Receiver Box Quick Installation Guide
HV-110 DVB-T HAM TV Receiver Box Quick Installation Guide PACKAGE CONTENTS 2 FRONT PANEL VIEW 2 BACK PANEL VIEW 2 BOARD VIEW 3 IR REMOTE CONTROLLER 4 FILL BATTERY TO IR CONTROLLERS: AAA X 2 PCS 4 SET BANDWIDTH
More informationWireless M-Bus Suite for Panasonic Evaluation Boards. Quick Start Guide
Wireless M-Bus Suite for Panasonic Evaluation Boards January 16, 2012 page 2 Document History 1.0 2011-07-20 First release dj 1.1 2011-07-25 Review dj 1.2 2011-07-27 Quick start changed dj 1.3 2011-09-13
More informationQuick Start Guide for the Turbo upsd DK3300-ELCD Development Kit- RIDE
Contents: Circuit Board upsd DK3300-ELCD Development Board with a upsd3334d-40u6 MCU with Enhanced Graphic LCD RLINK-ST, a USB-based JTAG adapter from Raisonance for debugging with Raisonance Integrate
More informationUCD3138. JTAG Configuration. Using CCS 6
UCD3138 JTAG MANUAL UCD3138 JTAG Configuration Using CCS 6 TI NDA Preliminary Document October 6 2014 PRODUCT PREVIEW information concerns products in the formative or design phase of development. Characteristic
More informationwith the Cisco Unified IP Color Key Expansion Module.
Cisco Unified IP Color KEM Setup Overview, page 1 KEM Power Information, page 2 Connect Single KEM to Cisco Unified IP Phone, page 2 Connect Two or More KEMs to Phone Using KEM Spine Connector, page 3
More informationX500 Parts Replacement Instructions
X500 Parts Replacement Instructions This document is intended for service personnel. It provides information not found in the user manual. For information such as replacing the battery pack, hard disk
More informationDell Inspiron Mini 10 RAM Replacement
Upgrade or replace RAM to boost speed and performance. Written By: Danielle Jarecki ifixit CC BY-NC-SA www.ifixit.com Page 1 of 12 INTRODUCTION This guide will give step-by-step instructions on how to
More informationPadFone Infinity. Standard Operating Procedure for Upgrading the Firmware to Android Kit Kat
PadFone Infinity E9675 Standard Operating Procedure for Upgrading the Firmware to Android Kit Kat Download the latest firmware from the ASUS Support site and follow the instructions described in this guide
More informationBrainPower Cranial Nerve Stimulator Firmware Reflashing Guide for Windows, MacOS & Linux
BrainPower Cranial Nerve Stimulator Firmware Reflashing Guide for Windows, MacOS & Linux This guide details the steps required to reflash GRC s CNS device using software hosted on Windows 7-10, MacOS or
More informationLAB #1: The CSM12C32 Module and PBMCUSLK Project Board
CS/EE 5780/6780 Handout #1 Spring 2007 Myers LAB #1: The CSM12C32 Module and PBMCUSLK Project Board Lab writeup is due to your TA at the beginning of your next scheduled lab. Don t put this off to the
More informationTools required: Philips Small/Hobby Screw Driver Flat Screw Driver RESET Card CR1220 Battery 3mm Allen Key Stylis or Sharp Pencil
info@icoolsport.com www. icool Touch Screen Memory Battery Replacement AND RE-SETTING SYSTEM CLOCK RESET Tools required: Philips Small/Hobby Screw Driver Flat Screw Driver RESET Card CR1220 Battery 3mm
More informationFirmware, Database, & PC Application Update Installation Instructions
Firmware, Database, & PC Application Update Installation Instructions IMPORTANT Please read before you begin the installation. To avoid possible errors, it is recommended to install the updates as described
More informationProcedure for Downloading & Installing the Auto-Update Platform and Updating Sensor- Aid/OBD II Module Firmware Versions
Procedure for Downloading & Installing the Auto-Update Platform and Updating Sensor- Aid/OBD II Module Firmware Versions 1 Contents Part A: Download and install the Auto-Update Platform Part B: Update
More informationDon t jump ahead, there is more you need to do first in order for this to work properly.
With the release of our new PD 502 & PD 602 portable terminals, you are required to use CPS v5.06.01.009 programming software. To maintain compatibility between the different DMR model radios, you will
More informationMSP430F471xx MCUs offer high accuracy, simultaneous sampling and anti-tamper for three-phase e-metering applications
MSP430F471xx MCUs offer high accuracy, simultaneous sampling and antitamper for threephase emetering applications Jennifer Barry MSP430 Product Marketing Engineer The Energy Landscape Energy Sources Conventional
More informationCascade Configuration Tool
Cascade Configuration Tool Version 1.0.10 Installation and Operations Manual 00-02-0724 01-25-11 Section 40 In order to consistently bring you the highest quality, full featured products, we reserve the
More informationFLASH GUI. User Manual V1.4 COPY RIGHTS ECOTRONS LLC ALL RIGHTS RESERVED.
FLASH GUI User Manual V1.4 COPY RIGHTS ECOTRONS LLC ALL RIGHTS RESERVED Http://www.ecotrons.com Note: If you are not sure about any specific details, please contact us at info@ecotrons.com. 1 Installation
More informationField Update Guide. for Raven Viper Pro
Field Update Guide for Raven Viper Pro Introduction The field update kit (P/N 117-0171-467) is designed to allow the Raven Viper Pro to utilize the automatic power down feature without returning the console
More informationService Manual - Memory Upgrade
Inspiron 14 3000 Series Service Manual - Memory Upgrade Regulatory Model: P53G Regulatory Type: P53G002 Contents Before working inside your computer...3 Before you begin... 3 Safety instructions... 3 Recommended
More informationThe Cisco Wireless IP Phone 8821-EX has not been tested or certified with any accessories for use in Potentially Explosive Atmosphere.
Supported, page 1 Headsets, page 1 Cisco Wireless IP Phone 8821 Desktop Charger, page 2 Cisco Wireless IP Phone 8821 Multicharger, page 6 Secure the Charger with a Cable Lock, page 10 Supported You can
More informationConfiguring RUSHWORKS 3n1 for tracking using the Setup Utility
Configuring RUSHWORKS 3n1 for tracking using the Setup Utility System Operation For best results, the camera should be positioned in the rear center of the room, between 30 and 50 from the front coverage
More informationIMPORTANT NOTE for. Choose the zip file v and unzip it in USB. Do not rename the UPG folder. Follow
IMPORTANT NOTE for (HTB3280G/12 HTB3520/40/55/94/98 HTB3520G/12/51 HTB3550/40/98 HTB3550G/12 HTB3580/40/79/98 HTB3580G/12/51 HTB4520G/51 HTB4580G/51 HTB5260G/12 HTB5520/55/94/98 HTB5520G/12 HTB5550/98
More informationGo!Control Firmware Update Tool (for PC) Installation and Operation Quick Start
Go!Control Firmware Update Tool (for PC) Installation and Operation Quick Start May 1, 2012 Overview This document provides instructions for using the Firmware Update Tool to update a Go!Control panel
More informationPhase One. ixu-rs 1000 / ixu 1000 / ixu 150 UAV Camera Systems. For DJI M600 & M600 PRO. Installation Guide
Phase One ixu-rs 1000 / ixu 1000 / ixu 150 UAV Camera Systems Installation Guide For DJI M600 & M600 PRO 1 Phase One ixu-rs 1000 / ixu 1000 / ixu 150 UAV Camera Systems Installation Guide For DJI M600
More informationDLP-RFID2-EDK2 SETUP PROCEDURE
DLP-RFID2-EDK2 SETUP PROCEDURE This product is designed to make it easy to both test the DLP-RFID2 module without developing your own hardware and provide an easy-to-use platform for those wishing to program,
More informationWritten By: Alan Weihe
This is a step by step guide for removing the LCD bracket of the Nikon Coolpix P530 camera. Written By: Alan Weihe ifixit CC BY-NC-SA www.ifixit.com Page 1 of 9 INTRODUCTION A broken LCD bracket could
More informationUser Guide Diamond Drive Cartridge System DDCSSAS / DDCSIS DDCSSAU / DDCSIU
T E C H N O L O G I E S User Guide Diamond Drive Cartridge System DDCSSAS / DDCSIS DDCSSAU / DDCSIU www.addonics.com Technical Support If you need any assistance to get your unit functioning properly,
More informationIAR EWARM Quick Start for. Holtek s HT32 Series Microcontrollers
IAR EWARM Quick Start for Holtek s Microcontrollers Revision: V1.10 Date: August 25, 2011 Table of Contents 1 Introduction... 5 About the Quick Start Guide... 5 About the IAR EWARM... 6 2 System Requirements...
More informationQuick Start Guide. Model #1690 Wireless Controller & Entertainment Hub
Model #1690 Wireless Controller & Entertainment Hub Quick Start Guide This guide provides easy, step-by-step instructions on setting up your new hardware and experiencing your aquarium like never before!
More informationUART Devices. ECE 480: Design Team 3. Application Note. By: Hoyoung Jung. Date: 4/3/15
UART Devices ECE 480: Design Team 3 Application Note By: Hoyoung Jung Date: 4/3/15 Abstract The integration and communication of electronic systems requires the receiving and transmitting of data. In order
More informationHow to upgrade my PHILIPS ADSL 515 Wireless Base Station
This How-To manual will answer the following questions: 1.Why should I upgrade my ADSL 515 wireless base station firmware? 2.How do I know which firmware version I have now? 3.How do I know what the latest
More informationInstallation tutorial for the Skomer IDE
Installation tutorial for the Skomer IDE DRAFT The Skomer IDE (Integrated Development Environment) is based on a set of tools: - Eclipse: used the development environment - Cygwin: used as the processor
More informationEZ430-C9. Getting Started with Kionix EZ430-C9 Evaluation Board for the Texas Instruments MSP430 USB Stick Development Tool
Getting Started with Kionix EZ430-C9 Evaluation Board EZ430-C9 Getting Started with Kionix EZ430-C9 Evaluation Board for the Texas Instruments MSP430 USB Stick Development Tool 36 Thornwood Dr. Ithaca,
More informationFirmware zippack name : R exe Firmware File Name : Dell1815dn_V _AutoUpgrade.exe
Updating Firmware on the Dell Laser Printer MFP 1815dn NOTICE: Do not turn off your printer or computer, or disconnect any cables during this operation. Doing this will corrupt the memory and the printer
More informationCanon PowerShot SX530 HS Shutter Release Cover Replacement
Canon PowerShot SX530 HS Shutter Release Cover Replacement Replacement instructions to the plastic cover holding the shutter release button, the button typically used to take pictures. Written By: Aaron
More informationConfiguring the Xilinx Spartan-6 LX9 MicroBoard
Configuring the Xilinx Spartan-6 LX9 MicroBoard Version 1.3 Table of Contents Table of Contents... 2 Table of Figures... 3 Revision History... 4 Overview... 5 Configuration and Programming via the on-board
More informationirespond Quick Reference Guide
irespond Quick Reference Guide Contact irespond customer support at (888) 325-6565 x6 or email support@irespond.com if you need assistance. Rev 7.0.6.0 TABLE OF CONTENTS SOFTWARE INSTALLATION... 2 HARDWARE
More informationInspiron Service Manual. 2-in-1. Computer Model: Inspiron Regulatory Model: P69G Regulatory Type: P69G001
Inspiron 13 5000 2-in-1 Service Manual Computer Model: Inspiron 13-5378 Regulatory Model: P69G Regulatory Type: P69G001 Notes, cautions, and warnings NOTE: A NOTE indicates important information that helps
More informationCanon EOS Rebel T4i Motherboard
Canon EOS Rebel T4i Motherboard Replacement This guide will show you how to replace the motherboard on your Canon Rebel T4i. Written By: Jordan Rabold ifixit CC BY-NC-SA www.ifixit.com Page 1 of 10 INTRODUCTION
More informationOlimex Field Update Kit
Olimex Field Update Kit Table of Contents Overview... 2 To download the field update software... 2 To install the HQLoader software... 2 To install the USB to Serial Converter driver... 2 To install the
More informationFuturecom Systems Group, ULC. PDR8000 Firmware Upgrade Instructions. Document: 8M088X01 Revision: R1.0 Date:
Futurecom Systems Group, ULC PDR8000 Firmware Upgrade Instructions Document: 8M088X01 Revision: R1.0 Date: 2018-08-01 Document Revisions Rev Date Notes & References R1.0 31 Jul 2018 Instructions for Release
More informationHow to add a Second Drive to a Mac mini (2012) using the OWC Data Doubler SSD/2.5 Installation Kit
Instructional Video Series How to add a Second Drive to a Mac mini (2012) using the OWC Data Doubler SSD/2.5 Installation Kit Skill Level: Challenging Time to Complete: Approximately 45 Minutes Required
More informationINSTALLING OR UPGRADING THE DVR S HDD
AHD & NVR SERIES INSTALLING OR UPGRADING THE DVR S HDD www.nightowlsp.com Installing or Upgrading the DVR s HDD Most DVR s included in our kits already have a pre-installed internal HDD and is ready to
More informationWritten By: Joel groff
Replace the lens of the camera. Written By: Joel groff ifixit CC BY-NC-SA www.ifixit.com Page 1 of 17 INTRODUCTION This guide shows how to replace the Lens of the Canon PowerShot SX 530 HS. TOOLS: Phillips
More informationApple ipod Mini Take Apart Repair Manual
Apple ipod Mini Take Apart Repair Manual Copyright 2006 Powerbookmedic.com. All rights reserved. Any portion of this manual may not be copied, reproduced, or distributed without the express written consent
More informationBASICS OF THE RENESAS SYNERGY PLATFORM
BASICS OF THE RENESAS SYNERGY PLATFORM TM Richard Oed 2018.11 02 CHAPTER 7 STARTING THE RENESAS SYNERGY PROMOTION KIT PK-S5D9 FOR THE FIRST TIME CONTENTS 7 STARTING THE RENESAS SYNERGY PROMOTION KIT PK-S5D9
More informationContents About This Guide Audience Revision History
Contents About This Guide............................. 2 Audience............................................... 2 Revision History......................................... 2 Conventions............................................
More informationUser s Guide. for. USB + MSP430 Evaluation System (USB430) 6 April From. SoftBaugh
User s Guide for USB + MSP430 Evaluation System (USB430) 6 April 2004 From SoftBaugh Custom Software, Firmware, Hardware, and Project Management Consulting 4080 McGinnis Ferry Road Suite 604 Alpharetta,
More informationFlashPro430. User s Manual
FlashPro430 Fast USB-MSP430 Flash Programmer User s Manual Software version 3.5 October-20-2006 Elprotronic Inc. 91 Alpine Crescent Richmond Hill, Ontario, L4S-1V9 CANADA Web site: www.elprotronic.com
More informationDELL U2410 USB FW Upgrade Instruction
DELL U2410 USB FW Upgrade Instruction Version 01 Important Note: There are risks in FW upgrade. The U2410 screen will be blank during the upgrade process. We recommend you upgrade the U2410 from a notebook
More informationHow to update FOCUS 30 Firmware
14 March 2013 How to update FOCUS 30 Firmware This support note will guide you through updating the firmware on a FOCUS 30 instrument. Note : If your FOCUS 30 has previously received a firmware upgrade
More informationDell Inspiron 700m RAM Replacement
Replace or upgrade the RAM on your 700m. Written By: Jeff Suovanen ifixit CC BY-NC-SA www.ifixit.com Page 1 of 7 INTRODUCTION The 700m has room for two sticks of RAM, but one is hidden under the keyboard.
More informationTool Setup. Code Composer Studio
Tool Setup Code Composer Studio Code Composer Studio Integrated Development Environment (IDE) Free for non-commercial use Eclipse based We will use this for our MSP432 and Console Based code development
More informationirespond Quick Reference Guide
irespond Quick Reference Guide Contact irespond customer support at (888) 325-6565 x6 or email support@irespond.com if you need assistance. Rev 6.7.1 CONTENTS Software Installation... 3 Hardware Setup...
More informationSimple Instructions for 808 HD Car Key Micro Camera (#16)
Simple Instructions for 808 HD Car Key Micro Camera (#16) Thank you for your purchase of our 808 Car Key Micro-camera (#16). If this is the first time you are using a product of this kind, please follow
More informationFlashPro-ARM GangPro-ARM
FlashPro-ARM GangPro-ARM Flash and Gang Programmer for ARM core MCUs User Guide Elprotronic Inc. 35 Austin Rumble Court King City Ontario, L7B0B2 CANADA Web site: E-mail: info@elprotronic.com Fax: 905-539-0474
More informationID-Manager. PC program for Windows 98 and later versions of Windows. User manual for ID Manager
ID-Manager PC program for Windows 98 and later versions of Windows User manual for ID Manager Contents 1 INSTALLATION...3 1.1 MANAGER INSTALLATION...3 1.2 INSTALLATION OF USB DRIVER...3 2 ID MANAGER PROGRAM
More informationWritten By: Jonathan Wear
JBL Flip 2 MicroUSB Port Replacement This guide will walk you through replacing the microusb port for this device. Written By: Jonathan Wear ifixit CC BY-NC-SA www.ifixit.com Page 1 of 12 INTRODUCTION
More informationihome ih9 Infrared Receiver Replacement
ihome ih9 Infrared Receiver Replacement Replace the chip for receiving data from the remote control Written By: Charlie Ross ifixit CC BY-NC-SA www.ifixit.com Page 1 of 11 INTRODUCTION To complete this
More informationLDC1000 SENT Bridge MSP-EXP430F5529LP based Getting Started
LDC1000 SENT Bridge MSP-EXP430F5529LP based Getting Started Contents 1. Quick Start... 2 2. Needed Equipment... 2 2.1 Hardware... 2 2.2 Software... 2 2.3 Recommended Documents... 3 2.4 Additional Documents...
More informationUpdating your uscope Firmware
2018-08-23 Updating your uscope Firmware Step 1 Update Computer Requirements All uscopes can be updated using a Windows Vista or 7 computer. Only newer uscopes can be updated using a Windows 10 computer.
More informationInstallation Guide for. Phase One ixg Camera. Developed for Phase One Cultural Heritage, Scientific and Industrial Imaging Solutions
Installation Guide for Phase One ixg Camera Developed for Phase One Cultural Heritage, Scientific and Industrial Imaging Solutions Installation Guide for Phase One ixg Camera Developed for Phase One Cultural
More informationAgilent 971-FP. Software Installation Instructions
Software Installation Instructions This document contains installation and upgrade procedure for the Agilent 971-FP Flash Purification Software v3.2. Introduction This document describes how to install
More informationNexus 7 2nd Generation Micro USB/Daughterboard Replacement
Nexus 7 2nd Generation Micro USB/Daughterboard Replacement Replace the Micro USB/Daughterboard on your Nexus 7 2nd Generation. Written By: Simon Krauter ifixit CC BY-NC-SA www.ifixit.com Page 1 of 11 INTRODUCTION
More informationRobotics Jumpstart Training II. EasyC: Software & Firmware Updates
Robotics Jumpstart Training II EasyC: Software & Firmware Updates Objectives: Learn how to update EasyC Current Version: 4.2.1.9 Learn how to update Firmware VEX Joystick (Controller) VEX Microcontroller
More informationPeopleNet TABLET Installation Guide. Version 1.1. A guide for new TABLET & new OBC installations.
Optional Image PeopleNet TABLET Installation Guide Version 1.1 A guide for new TABLET & new OBC installations. (Refer to the PeopleNet TABLET Upgrade Guide if upgrading from classic OBC to TABLET.) Revisions
More informationKeil TM MDK-ARM Quick Start for. Holtek s HT32 Series Microcontrollers
Keil TM MDK-ARM Quick Start for Holtek s Microcontrollers Revision: V1.10 Date: August 25, 2011 Table of Contents 1 Introduction... 5 About the Quick Start Guide... 5 About the Keil MDK-ARM... 6 2 System
More informationLPC2148 DEV BOARD. User Manual.
LPC2148 DEV BOARD User Manual www.coineltech.com www.coineltech.com Designed by CoiNel Technology Solutions LLP No-816, 2 nd Floor, 4 th B Cross, 9 th A Main, RPC Layout, Vijaynagar, Bangalore-560040 State:
More informationFirmware, Database, & PC Application Update Installation Instructions
Firmware, Database, & PC Application Update Installation Instructions IMPORTANT Please read before you begin the installation. To avoid possible errors, it is recommended to install the updates as described
More informationTube Washing Upgrade Guide. for Epson SureColor F2000
Tube Washing Upgrade Guide for Epson SureColor F2000 2016 guides.equipmentzone.com Page 1 of 14 Part 1 -How to Upgrade Epson F2000 Firmware Open your internet browser Select address bar located up top
More informationEMB-WMB169PA EMB-WMB868. Datasheet
EMB-WMB169PA EMB-WMB868 Datasheet Document information Versions & Revisions Revision Date Author Comments 1.0 09/08/2011 Embit Preliminary version 1.1 01/02/2012 Embit Updated pinout 1.2 26/04/2012 Embit
More informationAFE4400 and AFE4490 SPO2 Front End Demonstration Kit. Message Communication Protocol v4.0
AFE4400 and AFE4490 SPO2 Front End Demonstration Kit Message Communication Protocol for AFE4400 / AFE4490 EVM This document describes the message communication protocol for AFE4400 / AFE4490 EVM. The message
More informationVersa-Kit-30xx Getting Started Guide Rev 1.0
Versa-Kit-30xx Getting Started Guide Rev 1.0 1 contents: The development kit is a plug-and-play evaluation system for the VRS51L3xxx series of high performance, fully-integrated, FRAM-Enhanced 8051 microcontrollers
More informationZ-Accel. Introduction. Objectives
Z-Accel Introduction Z-Accel is a new packaging of our, now familiar Z-Stack into a more user-friendly format. If you need to implement a ZigBee solution quickly, Z-Accel could be your most promising alternative.
More informationSNMP Web Management. User s Manual
SNMP Web Management User s Manual Suitable Product: SNMP Web Card SNMP Web Box Management Software for Uninterruptible Power Supply Systems Table of Contents 1. Overview... 1 1.1 Introduction... 1 1.2
More informationSkywire LTE CAT4 Firmware Update
Skywire LTE CAT4 Firmware Update NimbeLink Corp Updated: September 2018 PN 30270 rev 5 NimbeLink Corp. 2018. All rights reserved. 1 Table of Contents Table of Contents 2 Introduction 3 Options for Updating
More informationIntroduction. Parameter Checker Program - CHC LAST UPDATED: 09/19/2018
LAST UPDATED: 09/19/2018 Parameter Checker Program - CHC Introduction This procedure tells you how to download and run the Parameter Checker program. Note that the examples in this procedure show the Windows
More informationAn ISO 9001 Company. BOP 1KW-MG FIRMWARE RETROFIT KIT
INSTRUCTION MANUAL 1. DESCRIPTION KEPCO An ISO 9001 Company. BOP 1KW-MG FIRMWARE RETROFIT KIT BOP 1KW-MG RETROFIT KIT 219-0597 Kepco KIT 219-0597 contains the PROMs used to upgrade the firmware for BOP
More informationASUS D550MA-DS01 Motherboard
ASUS D550MA-DS01 Motherboard Replacement This guide will show you how to remove the motherboard from the laptop. Steps included in this process are removing the screws, disconnecting cables, and removing
More informationAn ISO 9001 Company. BOP 1KW-MG FIRMWARE RETROFIT KIT
INSTRUCTION MANUAL 1. DESCRIPTION KEPCO An ISO 9001 Company. BOP 1KW-MG FIRMWARE RETROFIT KIT BOP 1KW-MG RETROFIT KIT 219-0621 Kepco KIT 219-0621-(n) contains the parts used to upgrade the firmware for
More informationIntroducing StellarisWare
Introducing StellarisWare Slide 1: This PTM will introduce you to StellarisWare and provide you with a better understanding of its applications. StellarisWare is software that has been made to be used
More informationSERIAL PORT TOOL. N-Button Lite Quick Start Guide
SERIAL PORT TOOL N-Button Lite Quick Start Guide SERIAL PORT TOOL N-Button Lite Quick Start Guide Copyright 2014 All Rights Reserved. Notice: Portions of this manual require internet access. Table of Contents
More informationEM6819 TOOLS DEVELOPMENT QUICK START
EM MICROELECTRONIC - MARIN SA EM6819 TOOLS DEVELOPMENT QUICK START TABLE OF CONTENTS 1 INTRODUCTION... 2 1.1 DOWNLOADING THE SOFTWARE... 2 1.2 INSTALLING THE SOFTWARE... 2 2 SETTING UP THE RAISONANCE TOOLS
More informationE-bot and E-bot ADV Firmware Upgrade Manual for v1.3.0
E-bot and E-bot ADV Firmware Upgrade Manual for v1.3.0 This manual introduces Firmware upgrade and TTS data upgrade. The firmware upgrade is necessary. The TTS data upgrade is not necessary if the version
More informationCoiNel Technology Solutions LLP. LPC2148 ARTIST Instruction Manual LPC2148 ARTIST. Instruction manual. Revision 1
LPC2148 ARTIST Instruction manual Designed by CoiNel Technology Solutions LLP No-816, 2 nd Floor, 4 th B Cross, 9 th A Main, RPC Layout, Vijaynagar, Bangalore-560040 State: Karnataka Country: India www.coineltech.com
More informationOmniCounter Pro Infrared People Counter. People Counter. Introduction. Table of Contents. Model: OmniCounter Pro
Introduction The Traf-Sys/Walker Wireless OmniCounter Pro Wireless Infrared s provide a simple and elegant, yet effective way to track foot traffic through a given area or entrance. The counter consists
More informationRacegun Interface Program -RIP This section covers installation and use of the PC-software for the Racegun grip.
Racegun Interface Program -RIP This section covers installation and use of the PC-software for the Racegun grip. This guide is for the RIP version 1.X please visit www.raceguns.dk for an update if you
More informationFET-Pro430. User s Manual
FET-Pro430 MSP430 Flash Programmer User s Manual Software version 1.13 PM014A01 Rev.5 March-15-2007 Elprotronic Inc. 16 Crossroads Drive Richmond Hill, Ontario, L4E-5C9 CANADA Web site: www.elprotronic.com
More informationLockState RL 4000 User Guide
LockState RL 4000 User Guide www.resortlock.com Table of Contents Section 1: General Overview 1. Foreword... 3 2. Important Information.. 3 3. Software Installation.. 4 Section 2: Initial Lock Setup Manual
More informationElectronic Indicator
TIR ABS CR /MM Electronic Indicator Operating Manual Analog Display Analog Visual Display Incremental Measuring Mode SPC Cables USB, MTI, RS232 Measuring System in English or Metric Travel Reverse Auto
More information