ADS-SW(SI)-ALL01-AS-IG-EN

Transcription

1 install guide ADS-SW(SI)-ALL0-AS-IG-EN firmware ADS-SW(SI)-ALL0-AS-EN hardware ADS-MSW Document number 99 Revision Date 009 NOTICE The manufacturer will accept no responsability for any electrical damage resulting from improper installation of this product, be that either damage to the vehicle itself or to the installed device. This device must be installed by a certified technician. This guide has been written for properly trained technicians; a certain level of skill & knowledge is therefore assumed. Please review the Installation Guide carefully before beginning any work. Automotive Data Solutions Inc. 0

2 HOLD Hz V MIN MAX mv RANGE Ω ))))) ~ ~ Hz V ma 00 ma 0A! FUSED V 00V CAT IV 000V CAT III Ω COM ~ A Hz Hz suggested TOOls - Of ADS-SW(SI)-ALL0-AS-IG-EN Page of 8 DOC.: # V DC Multimeter 0 Soldering iron and solder 0 Wire cutter 0 Wire stripper 0 Electrical tape LR+ LR+ SWI- SWI- G- G- LR- LR- SWI- SWI- Acc+ Acc+ RR+ RR+ SWI F SWI F Illum+ Illum+ RR- RR- SWI F SWI F LF+ LF+ AMP+ AMP+ SWI F SWI F LF- LF- ANT+ ANT+ SWI F SWI F RF+ RF+ SWI- SWI- SWI F SWI F RF- RF- SWI- SWI- SWI F SWI F Wire labels Automotive Data Solutions Inc. 0

3 INSTALLATI OVERVIEW - OF ADS-SW(SI)-ALL0-AS-IG-EN Page of 8 DOC.: # MODULE BACK VIEW A PROGRAMMING BUTT LED USB 0 PURPLE/RED - SWI CIRCUIT INPUT 0 PURPLE/YELLOW - SWI CIRCUIT OUTPUT/ANALOG INPUT 0 PINK/RED - SWI CIRCUIT INPUT 0 PINK/YELLOW - SWI CIRCUIT OUTPUT/ANALOG INPUT 0 BLACK/WHITE - SWI GROUND FEED (-) OUTPUT 0 RED - ESSORY POWER +V INPUT 0 BLACK - GROUND VEHICLE A B WEBLINK UPDATER CABLE (NOT INCLUDED) C USB WEB B C 0 BLUE/YELLOW - RADIO CTROL OUTPUT 0 RED 0 BLACK RADIO CTROL OUTPUT 0 WHITE AFTERMARKET RADIO Automotive Data Solutions Inc. 0

4 module INsTallaTI PROCEDuRE - Of ADS-SW(SI)-ALL0-AS-IG-EN Page of 8 DOC.: # Refer to WIRE CHART and locate wires. 0 SWI- If SWI- wire exists, connect module PINK/ RED wire (Connector A, Pin ) to SWI- wire. WARNING: Do not connect module PURPLE/ YELLOW wire (Connector A, Pin ) nor PINK/ YELLOW wire (Connector A, Pin ). 0 SWI-F If another SWI-F wire exists, connect module BLACK/WHITE wire (Connector A, Pin ) to SWI-F wire. 0 V Connect module RED wire (Connector A, Pin ) to V accessory. NOTE: If installing a Kenwood radio, connect module BLUE/YELLOW wire (Connector C, Pin ) to remote input (radio BLUE/YELLOW wire). 0 Connect module BLACK wire (Connector A, Pin ) to ground. NOTE: If installing an Aftermarket radio, connect module.mm (/8 ) audio jack (Connector C, Pin, & ) to auxiliary input. 0 SWI- Connect module PURPLE/RED wire (Connector A, Pin ) to SWI- wire. 08 Module installation procedure completed. 0 SWI-F Connect module BLACK/WHITE wire (Connector A, Pin ) to SWI-F wire. (Disregard this step if no SWI-F wire is found). Automotive Data Solutions Inc. 0

5 functi PaIRINg ChaRT - Of ADS-SW(SI)-ALL0-AS-IG-EN Page of 8 DOC.: # SELECT ALPINE BLAUPUNKT CLARI JVC JVC 00-0 vehicle brand [X] RaDIO functi RaDIO functi RaDIO functi RaDIO functi RaDIO functi Acura [] Ford [] GM* At Bcm [] GM* Import [] GM* Wire At Radio [] Honda [] Hyundai [] Infiniti [] Kia [] Lexus [] Lincoln [] Mazda [] Mercury [] Mitsubishi [] Nissan [] Scion [] Subaru [] Suzuki [] Toyota [] *Buick, Cadillac, Chevrolet, GMC, Hummer, Isuzu, Oldsmobile, Pontiac, Saab, Saturn SELECT RaDIO brand [Y] Alpine [] Blaupunkt [] Clarion [] JVC [8] JVC 00-0 [] JVC w/o preset [9] Kenwood [] Pioneer [] Pioneer w/o preset [0] Sony [] Power [] Volume Up [] Volume Down [] Track Up [] Track Down [] Source [] Mute [] Play/Pause [8] Band [9] Preset Up [0] Preset Down [] Enter [] Display Info [] Answer Call [] Hang Up [] Menu [] Sound [] JVC W/O PRESET RaDIO functi Volume Up [] Volume Down [] Power [] Seek Up [] Seek Down [] Source [] Mute [] Enter [8] Answer [9] Hang Up [0] Voice Dial [] Power [] Volume Up [] Volume Down [] Seek Up [] Seek Down [] Track Up [] Track Down [] Source [8] Mute [9] Play/Pause [0] Display Info [] Answer [] Hang Up [] Menu [] Random [] Repeat [] KENWOOD RaDIO functi Volume Up [] Volume Down [] Track Up [] Track Down [] Source [] Mute [] Play/Pause [] Folder Up/AM [8] Folder Down/FM [9] Up/Disk Up [0] Down/Disk Down [] Direct [] Phone [] Repeat [] Sound [] Volume Up [] Volume Down [] Preset Up [] Preset Down [] Source Power [] Mute [] Play/Pause [] Band [8] Phone [9] Menu [0] Sound [] Answer [] Hang Up [] PIEER RaDIO functi Volume Up [] Volume Down [] Seek Up [] Seek Down [] Source [] Mute [] Band [] Preset Up [8] Preset Down [9] Display Info [0] Phone Menu [] Answer Call [] Hang Up [] Voice Recognition [] Volume Up [] Volume Down [] Power [] Seek Up [] Seek Down [] Source [] Mute [] Preset Up [8] Preset Down [9] Enter [0] Answer [] Hang Up [] Voice Dial [] PIEER W/O PRESET RaDIO functi Volume Up [] Volume Down [] Seek Up [] Seek Down [] Source [] Mute [] Band [] Display Info [8] Phone Menu [9] Answer Call [0] Hang Up [] Volume Up [] Volume Down [] Power [] Seek Up [] Seek Down [] Source [] Mute [] Preset Up [8] Preset down [9] Enter [0] Answer [] Hang Up [] Voice [] SY RaDIO functi Power [] Volume Up [] Volume Down [] Seek Up [] Seek Down [] Source [] Display Info [] Mute [8] Band [9] Sound [0] Automotive Data Solutions Inc. 0

6 Page of 8 DOC.: # functi PaIRINg PROCEDuRE - Of ADS-SW(SI)-ALL0-AS-IG-EN 0 NOTE: [X], [Y] & are numerical variables identified in the FUNCTI PAIRING CHART. 0 Turn key to position. 0 [X] [X] Press programming button [X] times. 09 LED will flash [X] times. 0 Refer to FUNCTI PAIRING CHART. [Y] Find the number associated to the radio brand: [Y]. 0 LED will turn solid GREEN. EXAMPLE: If the vehicle make number is, the programming button must be pressed times and the LED will flash times. NOTE: If LED flashes GREEN once [x], the module is already programmed. To reprogram the module, reset module and repeat programming procedure. 0 Press and hold programming button until LED turns solid RED to register selection. 0 Refer to FUNCTI PAIRING CHART. NOTE: To go back to function, press programming button repeatedly until function is reached. Press programming button until LED turns solid RED to register selection. Find the number associated to the vehicle make: [X]. 08 Wait, LED will flash GREEN time. Refer to FUNCTI PAIRING CHART. 0 [X] Automotive Data Solutions Inc. 0 [Y] [Y] Press programming button [Y] times. LED will flash [Y] times.

7 functi PaIRINg PROCEDuRE - Of ADS-SW(SI)-ALL0-AS-IG-EN Page of 8 DOC.: # LED will flash GREEN times to match the function. 8 Repeat steps and for every other steering wheel button and its corresponding function. Insert key into ignition. EXAMPLE: If LED flashes times, the corresponding function is. NOTE: LED will flash RED once [x] for function 0. Turn key to position. LED will remain. Choose a steering wheel button to pair with its corresponding function. NOTE: LED will flash RED once [x] then will flash GREEN once [x] for function. Function pairing procedure completed. EXAMPLE: The steering wheel Volume Up button must be paired with the Volume Up function. 9 Press and hold programming button until LED turns solid GREEN. LED will remain solid green. NOTE: Test every steering wheel button, one by one, to verify aftermarket radio control. Press and hold that steering wheel button until LED turns solid GREEN to pair the function. 0 Turn key to position. NOTE: Press programming button once [x] to skip a function. Remove key. LED will turn. Automotive Data Solutions Inc. 0

8 module REsET PROCEDuRE - Of ADS-SW(SI)-ALL0-AS-IG-EN Page 8 of 8 DOC.: # Turn key to position. Module reset procedure completed. STAR Press and hold programming button and turn key to position. Wait, LED will flash RED rapidly. (This may take up to 0 seconds.) Release programming button. Wait, LED will turn solid GREEN for seconds. Turn key to position. Automotive Data Solutions Inc. 0