PL2 OL-MIB-PL2. Alarms & Remote Start

Transcription

1 Alarms & Remote Start Omega R&D Inc. INSTALL GUIDE OL-MIB-PL PL Available for : OL-MDB- Rev. Date: November 0, 0 Doc. No.: ##700## 009 The brand names and logos found in this guide are property of their respective owners. Omega R&D Inc. 0 NOTICE: The manufacturer will accept no responsibility for any electrical damage resulting from improper installation of this product, be that either damage to the vehicle itself or to the installed device. This device must be installed by a certified technician. This guide has been written for properly trained technicians; a certain level of skill & knowledge is therefore assumed. Please!review the Installation Guide carefully before beginning any work.

2 Page of OL-MIB-PL Doc. No.: ##700## 009 install type SeLeCtiOn FeaTUres make CHeVroleT pontiac model saturn year INsTall Type DaTa ImmobIlIzer bypass Equinox 0-06 Malibu 97-0 Torrent 06 L 00-0 S 00-0 Vue 0-07

3 Page of OL-MIB-PL Doc. No.: ##700## 009 type - wiring DIAGRAM REMOTE STARTER NOTE STANDARD VOLT, IGNITION AND ACCESSORY, STILL REQUIRED FROM THE REMOTE STARTER. MULTIPLEX CIRCUIT IS CONTROLLED FROM MODULE USING DATA, THEREFORE NO ADDITIONAL RELAYS OR RESISTORS REQUIRED. V (+) GROUND (-) GWR (-) OUTPUT DATA MODE REQUIRED -> IGNITION (+) OUTPUT N/A LEGEND NOT REQUIRED IN DATA MODE (-WAY) NOT REQUIRED IN DATA MODE (-WAY) USE DATA MODE OR HARDWIRE MODE DATA MODE GWR (-) INPUT - BLUE/WHITE (NC) WHITE GROUND - BLACK V (+) - RED (NC) GREEN/BLACK (NC) BLUE/BLACK (NC) RED/WHITE (NC) BROWN (NC) PURPLE/YELLOW (NC) PURPLE/BLACK (NC) WHITE (NC) BLACK/WHITE (NC) GREEN (NC) PURPLE/WHITE WHITE/BLACK (NC) WHITE/RED (NC) WHITE (NC) YELLOW/BLACK (NC) YELLOW/RED (NC) YELLOW - PASSLOCK BROWN/RED (NC) BROWN/YELLOW (NC) ORANGE/BLACK (NC) ORANGE/WHITE - KEYSENSE (-) ORANGE - DATA (J80) PINK/BLACK (NC) PINK - IGNITION (+) INPUT PASSLOCK LTGREEN - KEYSENSE WHITE YELLOW - ( TO VOLTS) BLACK - GROUND CONNECT KEY SENSE ONLY FOR THE FOLLOWING MODELS: CHEVROLET EQUINOX PONTIAC TORRENT SATURN VUE PURPLE OBDII CONNECTOR LOCATED UNDER DRIVER SIDE DASH

4 Page of OL-MIB-PL Doc. No.: ##700## 009 installation MODe SeLeCtiOn Press and release programming button to select installation mode. LED flashes (X) once = DATA MODE LED flashes (X) twice = STANDARD HARDWIRE MODE! Press and hold programming button until LED turns solid GREEN to register selection. After registration, follow Factory Reset Procedure to change installation mode and restart this procedure. MODULe PrOgrAMMing PrOCeDUre Insert key into ignition. Wait, LED will turn solid GREEN for seconds. START Turn key to START position. OFF (If after seconds the LED did not turn solid GREEN, press on the programming button once.) Turn key to OFF position. Module Programming Procedure completed.

5 Page of OL-MIB-PL Doc. No.: ##700## 009 identify VeHiCLe year Locate the Vehicle Identification Number (VIN) and identify the 0th character. A Y N T A L 8 D R 0 X Match the VIN s 0th character to its corresponding year. l > 990 s > 99 y > 000 > 00 a > 00 m > 99 T > 996 > 00 6 > 006 b > 0 N > 99 V > 997 > 00 7 > 007 C > 0 p > 99 W > 998 > 00 8 > 008 D > 0 r > 99 X > 999 > 00 9 > 009 e > 0 led status Flashing RED DIaGNosTICs DUrING programming DUrING remote start WITH IGNITIoN off Missing/wrong information from firmware or vehicle Incorrectly programmed Solid RED Waiting for more vehicle information Incorrectly programmed Flashing GREEN Additional steps required to complete programming MODULe DiAgnOStiCS Correctly programmed and operational Incorrectly programmed or connected Not programmed waiting for more vehicle information False ground when running status from remote starter Solid GREEN then OFF Correctly programmed Reset in progress Reset in progress OFF No activity or already programmed Invalid ground when running status from remote starter At rest and ready for a remote start sequence FACtOry reset PrOCeDUre DISCONNECT all connectors from module EXCEPT the black -PIN standard or optional data DISCONNECT black -PIN standard or optional data 6 LED will turn solid red for seconds. RESET COMPLETED. RECONNECT all connectors. PRESS AND HOLD programming button while connecting either -PIN standard or optional data When LED flashes red, RELEASE programming button. 7! Repeat programming procedure. Failure to follow procedure may result with a DTC or a CHECK ENGINE error message. this product is protected by one or more of the following patents: U.S. LetterS PAtent no.,79,; 6,0,60; 6,,00; 6,9,6; 6,7,7; 6,97,7; 6,6,876; 6,9,; 6,9,; 6,696,97; 6,76,88; 6,76,886; 6,77,67; 6,8,89; 6,9,70; 7,00,0; 7,0,86; 7,06,6; 7,06,7; 7,068,; 7,0,80; 7,0,679; 7,,08; 7,69,96; 7,78,9; 7,89,; 7,0,97; CAnADiAn PAtent no.,0,8;,,0;,6,670;,,99;,,0;,,07;,,08;,,0;,0,89;,,90;,,96;,,87; european PAtent no.,0,8; De T; U.S. 000; ; ; ; ; ; ep006; 808; 807;