FM3 INSTALL GUIDE OL-BLADE-AL(TB)-FM3-EN. Alarms & Remote Start Automotive Data Solutions Inc.

Transcription

1 Alarms & Remote Start Automotive Data Solutions Inc. INSTALL GUIDE OL-BLADE-AL(TB)-FM3-EN AVAILABLE FOR : OL-BLADE-AL Rev. Date: February 26, 2016 Doc. No.: ##26870## FM3 U.S. PATENT NO. 8,856,780 The brand names and logos found in this guide are property of their respective owners. NOTICE: The manufacturer will accept no responsibility for any electrical damage resulting from improper installation of this product, be that either damage to the vehicle itself or to the installed device. This device must be installed by a certified technician. This guide has been written for properly trained technicians; a certain level of skill & knowledge is therefore assumed. Please!review the Installation Guide carefully before beginning any work.

2 Page 2 of 11 OL-BLADE-AL(TB)-FM3-EN Doc. No.: ##26870## INSTALL TYPE SELECTI FeaTUres MaKe Ford ModeL LInCoLn year InsTaLL Type data IMMoBILIZer Bypass C-Max STD key Edge STD key Escape STD key Expedition STD key Explorer STD key F150 / F150 SVT Raptor STD key F250 / Super Duty / Diesel STD key F350 / Super Duty / Diesel STD key Fiesta STD key Flex STD key Focus STD key Taurus STD key Transit STD key Transit Connect STD key MKX STD key

3 Page 3 of 11 OL-BLADE-AL(TB)-FM3-EN Doc. No.: ##26870## TYPE 1 - WIRE CROSS REFERENCE CHART MaKe Ford ModeL year WIre description LInCoLn name CoLor Type position WIre CoLor polarity ModULe LoCaTIon CoMponenT LoCaTor Edge Expedition Explorer F150 / F150 SVT Raptor F250 / Super Duty / Diesel F350 / Super Duty / Diesel Flex Taurus Transit MKX *Wire color may vary, refer to pin-out. Tx C252 Black 4 pin 3 Yellow/Orange (DATA) PATS module, ignition switch ~ Rx C252 Black 4 pin 4 Purple/Gray (DATA) PATS module, ignition switch ~ Tx C252 Black 4 pin 3 Purple/Brown (DATA) PATS module, ignition switch ~ Rx C252 Black 4 pin 4 Blue/Gray (DATA) PATS module, ignition switch ~ Tx C252 Black 4 pin 3 Yellow/Orange (DATA) PATS module, ignition switch ~ Rx C252 Black 4 pin 4 Purple/Red or Purple/Gray* (DATA) PATS module, ignition switch ~ Tx C252 Black 4 pin 3 Yellow/Orange* (DATA) PATS module, ignition switch ~ Rx C252 Black 4 pin 4 Purple/Gray* (DATA) PATS module, ignition switch ~ Tx C252 Black 4 pin 3 Purple/Gray* (DATA) PATS module, ignition switch ~ Rx C252 Black 4 pin 4 Yellow/Orange* (DATA) PATS module, ignition switch ~ Tx C252 Black 4 pin 3 Purple/Gray* (DATA) PATS module, ignition switch ~ Rx C252 Black 4 pin 4 Yellow/Orange* (DATA) PATS module, ignition switch ~ Tx C252 Black 4 pin 3 Yellow (DATA) PATS module, ignition switch ~ Rx C252 Black 4 pin 4 Purple (DATA) PATS module, ignition switch ~ Ground C252 Black 4 pin 2 Black/White (-) PATS module, ignition switch ~ Tx C252 Black 4 pin 3 Yellow/Orange (DATA) PATS module, ignition switch ~ Rx C252 Black 4 pin 4 Purple/Gray (DATA) PATS module, ignition switch ~ Ground C252 Black 4 pin 2 Black/White (-) PATS module, ignition switch ~ Tx C252 Black 4 pin 3 Yellow/Orange (DATA) PATS module, ignition switch ~ Rx C252 Black 4 pin 4 Purple/Gray (DATA) PATS module, ignition switch ~ PATS power C252 Black 4 pin 1 Yellow/Purple (+) PATS module, ignition switch ~ Tx C252 Black 4 pin 3 Yellow/Orange (DATA) PATS module, ignition switch ~ Rx C252 Black 4 pin 4 Purple/Gray (DATA) PATS module, ignition switch ~

4 Page 4 of 11 OL-BLADE-AL(TB)-FM3-EN Doc. No.: ##26870## TYPE 1 - WIRING DIAGRAM IGNITI SWITCH REMOTE STARTER BLACK CNECTOR PATS POWER (+) TX RX ORANGE/BLACK *BLADE CNECTOR EXACT PIN-OUT WHITE/RED WHITE PINK/BLACK BROWN/RED ORANGE BLUE/RED GREEN/RED GRAY/RED WHITE/BLACK PINK BLACK BROWN/YELLOW ORANGE/WHITE BLUE/YELLOW YELLOW GRAY/YELLOW WHITE/BLACK - TX CNECTOR SIDE WHITE/RED - TX VEHICLE SIDE WHITE (NC) YELLOW (NC) BROWN/RED (NC) BROWN/YELLOW (NC) ORANGE/BLACK - RX ORANGE/WHITE (NC) ORANGE (NC) PINK/BLACK (NC) PINK - PATS POWER (+) BLUE/RED (NC) BLUE/YELLOW (NC) GREEN/RED (NC) GRAY/RED - TX VEHICLE SIDE GRAY/YELLOW (NC) BLACK (NC)

5 Page 5 of 11 OL-BLADE-AL(TB)-FM3-EN Doc. No.: ##26870## TYPE 2 - WIRE CROSS REFERENCE CHART MaKe ModeL Ford year WIre description name CoLor Type position WIre CoLor polarity ModULe LoCaTIon CoMponenT LoCaTor Tx C252 Black 4 pin 3 Yellow/Orange* (DATA) PATS module, ignition switch ~ C-Max Rx C252 Black 4 pin 4 Purple/Gray* (DATA) PATS module, ignition switch ~ PATS power C252 Black 4 pin 1 Gray/Orange* (+) PATS module, ignition switch ~ Ground C252 Black 4 pin 2 Black* (-) PATS module, ignition switch ~ Tx C252 Black 4 pin 3 Yellow/Orange* (DATA) PATS module, ignition switch ~ Escape Rx C252 Black 4 pin 4 Purple/Gray* (DATA) PATS module, ignition switch ~ PATS power C252 Black 4 pin 1 Gray/Orange* (+) PATS module, ignition switch ~ Ground C252 Black 4 pin 2 Black* (-) PATS module, ignition switch ~ Tx C252 Black 4 pin 3 Yellow* (DATA) PATS module, ignition switch ~ Fiesta Rx C252 Black 4 pin 4 Gray* (DATA) PATS module, ignition switch ~ PATS power C252 Black 4 pin 1 Blue/White* (+) PATS module, ignition switch ~ Ground C252 Black 4 pin 2 Black/White* (-) PATS module, ignition switch ~ Tx C252 Black 4 pin 3 Yellow/Orange* (DATA) PATS module, ignition switch ~ Focus Rx C252 Black 4 pin 4 Purple/Gray* (DATA) PATS module, ignition switch ~ PATS power C252 Black 4 pin 1 Gray/Orange* (+) PATS module, ignition switch ~ Ground C252 Black 4 pin 2 Black* (-) PATS module, ignition switch ~ Tx C252 Black 4 pin 3 Yellow/Orange* (DATA) PATS module, ignition switch ~ Transit Connect Rx C252 Black 4 pin 4 Purple/Gray* (DATA) PATS module, ignition switch ~ PATS power C252 Black 4 pin 1 Gray/Orange* (+) PATS module, ignition switch ~ Ground C252 Black 4 pin 2 Black* (-) PATS module, ignition switch ~ *Wire color may vary, refer to pin-out.

6 Page 6 of 11 OL-BLADE-AL(TB)-FM3-EN Doc. No.: ##26870## TYPE 2 - WIRING DIAGRAM PATS MODULE REMOTE STARTER C252 - BLACK TX RX ORANGE/BLACK *BLADE CNECTOR EXACT PIN-OUT WHITE/RED WHITE PINK/BLACK BROWN/RED ORANGE BLUE/RED GREEN/RED GRAY/RED WHITE/BLACK PINK BLACK BROWN/YELLOW ORANGE/WHITE BLUE/YELLOW YELLOW GRAY/YELLOW WHITE/BLACK - TX CNECTOR SIDE WHITE/RED - TX VEHICLE SIDE WHITE (NC) YELLOW (NC) BROWN/RED (NC) BROWN/YELLOW (NC) ORANGE/BLACK - RX ORANGE/WHITE (NC) ORANGE (NC) PINK/BLACK (NC) PINK - IGNITI (+) BLUE/RED (NC) BLUE/YELLOW (NC) GREEN/RED (NC) GRAY/RED - TX VEHICLE SIDE GRAY/YELLOW (NC) BLACK (NC) VEHICLE IGNITI (+)

7 Page 7 of 11 OL-BLADE-AL(TB)-FM3-EN Doc. No.: ##26870## CARTRIDGE INSTALLATI 1 Slide cartridge into unit. Notice button under LED. 2 Ready for Module Programming Procedure. TYPE 1 - MODULE PROGRAMMING PROCEDURE - 1 OF 2 NOTE I To complete this procedure, both OEM keys are required. 6 Insert key 2 into ignition. 1 Insert key 1 into ignition. 7 8 Turn key 2 to position. Wait, LED will turn solid RED then will turn. 2 Turn key 1 to position.! If the module s LED begins to flash RED, verify the RX and TX connections between the module and the vehicle. È TIME RESTRICTIºN COMING UP! 3 Wait, LED will turn solid RED then will turn. 9 Turn key 2 to position.! If the module s LED turns solid BLUE for 2 seconds, the Module Programming Procedure is completed. 10 TIME RESTRICTIºN Complete steps 10 to 13 within 5 SECDS. 11 Remove key 2. Press and release programming button. 4 Turn key 1 to position. 12 Insert key 2 into ignition. 5 Remove key 1. È IMPORTANT: READ NEXT PAGE!

8 Page 8 of 11 OL-BLADE-AL(TB)-FM3-EN Doc. No.: ##26870## TYPE 1 - MODULE PROGRAMMING PROCEDURE - 2 OF 2 13 Turn key 2 to position. Do not start vehicle. 16 Remove key Wait, LED will turn solid BLUE for 2 seconds. 17 Module Programming Procedure completed. 15 Turn key 2 to position.

9 Page 9 of 11 OL-BLADE-AL(TB)-FM3-EN Doc. No.: ##26870## CARTRIDGE INSTALLATI 1 Slide cartridge into unit. Notice button under LED. 2 Ready for Module Programming Procedure. TYPE 2 - MODULE PROGRAMMING PROCEDURE - 1 OF 2 NOTE I 1 2 3! To complete this procedure, both OEM keys are required. Insert key 1 into ignition. Turn key 1 to position. If the module s LED begins to flash RED, verify the RX and TX connections between the module and the vehicle. Wait, LED will turn solid RED then will turn È Insert key 2 into ignition. Turn key 2 to position. TIME RESTRICTIºN COMING UP! Wait, LED will turn solid RED then will turn. TIME RESTRICTIºN 9 Complete steps 9 to 11 within 5 SECDS. Turn key 2 to position. 10 Press and release programming button.! If the module s LED turns solid BLUE for 2 seconds, the Module Programming Procedure is completed. È IMPORTANT: READ NEXT PAGE! 4 Turn key 1 to position. 5 Remove key 1.

10 Page 10 of 11 OL-BLADE-AL(TB)-FM3-EN Doc. No.: ##26870## TYPE 2 - MODULE PROGRAMMING PROCEDURE - 2 OF 2 11 Turn key 2 to position. Do not start vehicle. 14 Remove key Wait, LED will turn solid BLUE for 2 seconds. 15 Module Programming Procedure completed. 13 Turn key 2 to position.

11 Page 11 of 11 OL-BLADE-AL(TB)-FM3-EN Doc. No.: ##26870## IDENTIFY VEHICLE YEAR 1 Locate the Vehicle Identification Number (VIN), identify the 10th character then match it to its corresponding year. Æ 4 3 A 5 Y 1 N 5 T A L 8 D 5 R 0 X Æ a 1980 L 1990 y 2000 a 2010 B 1981 M B 2011 C 1982 n C 2012 d 1983 p d 2013 e 1984 r e 2014 F 1985 s F 2015 G 1986 T G 2016 H 1987 V H 2017 J 1988 W J 2018 K 1989 X K 2019 Led status Flashing RED diagnostics during programming during remote start WITH IGnITIon off Missing/wrong information from firmware or vehicle Incorrectly programmed Solid RED Waiting for more vehicle information Incorrectly programmed Flashing BLUE Additional steps required to complete programming MODULE DIAGNOSTICS Correctly programmed and operational Incorrectly programmed or connected Not programmed waiting for more vehicle information False ground when running status from remote starter Solid BLUE then Correctly programmed Reset in progress Reset in progress No activity or already programmed Invalid ground when running status from remote starter At rest and ready for a remote start sequence FACTORY RESET PROCEDURE 1 DISCNECT cartridge from remote starter. 3 LED will flash red. Immediately RELEASE programming button. 2 PRESS AND HOLD programming button while re-connecting cartridge to remote starter. 4 LED will turn solid red for 2 seconds. RESET COMPLETED. 5 RECNECT all connectors. Repeat programming procedure.! Failure to follow procedure may result with a DTC or a CHECK ENGINE error message.