Discover Video. Mantis Encoder. User Guide. Version 1.2. Discover Video LLC 10/7/2016

Transcription

1 Discover Video User Guide Version /7/2016 Discover Video LLC

2 Contents General Description...3 Installation...4 Find IP Address...5 Configuration...5 Setting...5 Record...8 Status...9 Network Setup Firmware Update Account Setup Restore Default Front Panel Operation & Notes Mantis Shelf Mantis Finder Scaling Warranty Page 2

3 Chapter 1: Introduction General Description The Discover Video Mantis is a live video encoder that provides live streaming and recording from a variety of video input types. It is an economical appliance that is ideal for IPTV, executive broadcasts, morning announcements, enterprise and web streaming. The Mantis appliance is compact and is used stand-alone on a desktop or other surface, and a 6-channel rack shelf is available for high density applications. Page 3

4 Chapter 2: Configuration Installation Connect desired Audio/Video input, 10/100 Ethernet, and Power. Power is supplied by an external AC power supply and connects to the Mantis via a locking DC connector. Video Input may be: HDMI Via HDMI connector (female) SDI Via BNC connector (female) Component Via Pr/Y/Pb BNC connectors (female) Composite/CVBS Via BNC connector (female) DVI/VGA via DVI connector, VGA via adaptor (female) Audio Input may be digital (included with HDMI or SDI), or may be analog via Left and Right RCA connectors (female). Ethernet is standard 10/100 supporting IP V4. RS-458 connecter is not currently used. Page 4

5 Find IP Address Apply power and turn the front panel switch to the on position. Allow a few minutes for the unit to boot up. The Mantis is configured for DHCP and will obtain an IP address automatically. To find the IP address used, insert a USB Flash Drive into the USB connector and wait a few moments. Mantis will write a file IP.txt which you may then open on a computer to read the IP address. The USB must be formatted FAT16 or else the file may not write properly. You may also use the finder application to discover the IP address over the network, or you may search your router s DHCP table to find the IP address used. Configuration Enter the IP address in a browser. When prompted, enter default username and password: Username: admin Password: Setting Set up the live streaming using the settings page: Page 5

6 Server Off Streaming is disabled RTSP Streaming is available from Mantis via RTSP RTMP Stream is available directly from Mantis as RTMP HLS Stream is available directly from Mantis as HLS RTMP Publish Stream is sent to Streaming Server (e.g. DEVOS, ARCUS, Streamsie Service, CDN). This is most used configuration. RTSP ES Elementary Stream is available directly from Mantis. Used in special cases. RAW UDB Stream is available from Mantis via IP Multicast XML Used for Remote Configuration. Set to disable unless instructed by Discover Video. Page 6

7 Video Select the desired video input Audio Digital, RCA, Line-in (mini-jack) Video Tuning / Volume Tuning not available for digital inputs Scale Down Normally set to No where the output resolution size is same as input, or select output resolution size. Input size must be scaleable. H264 Encode Main 3.0 (recommended), Main 3.1 Audio Stereo Stereo or Mono Stereo Bit Rate Normally 128K, or select desired rate Video Bit Rate Select desired streaming / recording bit rate Video Rate Mode VBR or CBR. VBR recommended. Analog Audio System SMPTE (recommended), EBU. Sets the input type when analog audio is used. Audio Only Disables video streaming, however video signal must be present for the stream to start. RTMP Publish URL Available is server set to RTMP_Publish. Enter the URL to push the stream to. If CDN requires authentication, enter username and password. RAW UDP Stream Available if server is set to RAW UDP, enter the IP Class D address and port (e.g port 5000). Apply Enters all values and applies them to the encoder. Page 7

8 Record Mantis can record to a USB device (including a high capacity drive). To use recording, insert a USB drive and check that it is accepted and available on the Record screen. Enter a record name prefix. The recorded file will begin with this and will append a number plus.mp4. Click on the USB icon to view the contents of the USB drive. Click on the Network Drive icon to view the contents on the FTP server, if FTP has been configured. Configure FTP by entering the server, username, and password, then select Connect to allow the Mantis to connect. Check File Upload After Record to automatically upload the justrecorded file after recording. Check Delete USB Files After Upload to remove the just-uploaded file after upload is complete (use this to preserve disk space on the USB drive). Record Starts Recording. Changes to Loading as recording starts, then changes to Stop Record. Select Stop Record to end the recording. Copy progress will show Finished when upload is complete if Upload After Record has been selected. USB storage must be formatted FAT32 Page 8

9 Status Status shows the current status of the Manis. Page 9

10 Network Setup Select Network Setup from the Settings page to configure the network. You may disable DHCP to set a fixed IP address. Firmware Update Select Firmware Update to update the Mantis with files provided by Discover Video. With the streaming server set to OFF, upload firmware ending in A, followed by B. Once the message Warning, Please reboot appears, cycle power to reboot. Page 10

11 Other Setup Select Other Setup to change the system password. Enter the original Account (username) and password then select Submit, then enter new Account (username) and password. Enter a device name for the Mantis, which will show up in the Mantis Finder program to ease device identification. Restore Default Select Restore Defaults to return the Mantis to factory default settings. Page 11

12 Front Panel Power turns power on/off USB Optional storage for recording Stream -- Press once for 3 sec to start streaming. Again to stop. Record Press once for 3 sec to start recording. Again to stop. SDI / DVI / VGA / YPbPr / AV / HDMI Press to select video input. NOTE: If XML Configuration is in use, front panel buttons are disabled. Page 12

13 Operation & Notes The Mantis does not deinterlace composite (CVBS) video. Some devices, including iphone6 (but not iphone 5 or ipad) may not display interlaced video. One work-around to this is to use HDMI input with an external composite-to-hdmi converter. When Mantis is set to HLS, the viewing URL is: You can view this directly on most SmartPhones and Tablets. When Mantis is set to RTMP, the viewing URL is: rtmp://[ip]/live/mantis (case sensitive). This can be viewed in the Discover Video player, 3 rd party players, and can be pulled in to DEVOS via Advanced/Pull function. When Mantis is set to RTSP, the viewing URL is: rtsp://[ip:8000]/live (case sensitive). The port cannot be changed. When Mantis is set to RAW UDP, the stream can be viewed using VLC player using udp://@[ip]:[port]. If viewing directly from Mantis via HLS or RTMP, only one simultaneous viewer is recommended (although several simultaneous viewers may be possible). To conduct Upload After Record, you must first connect to FTP server by selecting the connect button. After recording, you may select the USB icon to show all files on the recording media. Right-click on a file to download it to your computer. You can then edit the video, upload it DEVOS, Arcus, etc. Be sure to use a high capacity USB storage device, such as a Passport, Verbatum or similar flash/disk device. Small Thumb Drives will work, but recording video at high bit rate creates large files and you will want to be sure you have enough space! Storage device must be formatted for FAT32. If Mantis becomes unresponsive, you can restore the product to factory configuration by inserting USB with the reset code on it and cycling the power. This software can be downloaded from Mantis requires a valid video input before it will start to stream, including Audio Only setting. Page 13

14 Mantis Shelf The Mantis Shelf can mount up to six Mantis encoders and provides power supply and power distribution to the encoders. Install the encoders by securing them with the included screws (two on top, two on the bottom). Connect power using the included cables from the power distribution box to each encoder. Connect each Mantis to your network via Ethernet (you may find it convenient to use an inexpensive Ethernet switch associated with each shelf). Note that it may be difficult to see the MAC address label once the Mantis is mounted in the shelf. You should copy the MAC addresses, or mark them on your own visible labels. The MAC address help you identify each Mantis when using the Mantis IP finder program. Mantis Finder Use the Mantis IP Finder to locate the Mantis encoders on your network. The finder must be used on the same network as the encoders. The discovered encoders will show their MAC addresses to help you identify the Mantis. Page 14

15 Scaling The following scaling settings are supported. Output -> 1920x x x x x x x x240 Input 1080p i p i50 720p60 720p50 576p60 480p60 PAL NTSC Page 15

16 Warranty Mantis has a 1 year Return-To-Factory limited warranty, starting on the date of shipment. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE (OR JURISDICTION TO JURISDICTION). DISCOVER VIDEO LLC RESPONSIBILITY FOR MALFUNCTIONS AND DEFECTS IN HARDWARE IS LIMITED TO REPAIR AND REPLACEMENT AS SET FORTH IN THIS WARRANTY STATEMENT. ALL EXPRESS AND IMPLIED WARRANTIES FOR THE PRODUCT, INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTIES AND CONDITIONS OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED IN TIME TO 12 MONTHS FROM DATE OF SHIPMENT. NO WARRANTIES, WHETHER EXPRESS OR IMPLIED, WILL APPLY AFTER THE LIMITED WARRANTY PERIOD HAS EXPIRED. SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THIS LIMITATION MAY NOT APPLY TO YOU. WE DO NOT ACCEPT LIABILITY BEYOND THE REMEDIES PROVIDED FOR IN THIS LIMITED HARDWARE WARRANTY OR FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES, INCLUDING, WITHOUT LIMITATION, ANY LIABILITY FOR THIRD-PARTY CLAIMS AGAINST YOU FOR DAMAGES, FOR PRODUCTS NOT BEING AVAILABLE FOR USE, OR FOR LOST DATA OR LOST SOFTWARE. OUR LIABILITY WILL BE NO MORE THAN THE AMOUNT YOU PAID FOR THE PRODUCT THAT IS THE SUBJECT OF A CLAIM. THIS IS THE MAXIMUM AMOUNT FOR WHICH WE ARE RESPONSIBLE. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU. Page 16