ID ISC.MR101 ID ISC.PR101 ID ISC.PRH101

Transcription

1 OBID i-scan MANUAL ID ISC.MR101 ID ISC.PR101 ID ISC.PRH101 History of Firmware Revisions final public SWRN MR_PR_PRH101.doc

2 Copyright 2010 by FEIG ELECTRONIC GmbH Lange Strasse 4 D Weilburg-Waldhausen Tel.: Edition: sb/10/03/11 - swrn mr_pr_prh101.doc Note With the edition of this document, all previous editions become void. Indications made in this manual may be changed without previous notice. Copying of this document, and giving it to others and the use or communication of the contents thereof are forbidden without express authority. Offenders are liable to the payment of damages. All rights are reserved in the event of the grant of a patent or the registration of a utility model or design. Composition of the information in this document has been done to the best of our knowledge. FEIG ELECTRONIC GmbH does not guarantee the correctness and completeness of the details given in this manual and may not be held liable for damages ensuing from incorrect or incomplete information. Since, despite all our efforts, errors may not be completely avoided, we are always grateful for your useful tips. The instructions given in this manual are based on advantageous boundary conditions. FEIG ELECTRONIC GmbH does not give any guarantee promise for perfect function in cross environments. FEIG ELECTRONIC GmbH assumes no responsibility for the use of any information contained in this document and makes no representation that they free of patent infringement. FEIG ELECTRONIC GmbH does not convey any license under its patent rights nor the rights of others. OBID is registered trademark of FEIG ELECTRONIC GmbH. OBID i-scan is registered trademark of FEIG ELECTRONIC GmbH. I-CODE is registered trademarks of NXP. Tag-it TM is a registered trademark of Texas Instruments Incorporated General information's regarding this document The following figure formats are used: 0...9: for decimal figures 0x00...0xFF: for hexadecimal figures, b0...1 for binary figures. The hexadecimal value in brackets "[ ]" marks a control byte (command). FEIG ELECTRONIC GmbH Page 2 of 12 SWRN MR_PR_PRH101.doc

3 Content Content 3 History of Firmware Revisions (RF-Controller) MR/PR101 4 USB-Reader 4 Serial-Reader 5 History of Firmware Revisions (RF-Controller) PRH101 8 USB-Reader 8 Serial-Reader 9 Bluetooth-Reader 10 History of Firmware Revisions (USB-Controller) 12 FEIG ELECTRONIC GmbH Page 3 of 12 SWRN MR_PR_PRH101.doc

4 History of Firmware Revisions (RF-Controller) MR/PR101 USB-Reader V1.00(USB) ( ) Initial Version: no Scan Mode supported. V1.01(USB) ( ) Scan Mode supported. V1.02(USB) ( ) Advanced Mode: Advanced Mode supported. V1.03(USB) ( ) New Transponder Customer Commands Fujitsu Fast Commands (MB89R118 Tags). TI Tag-it HF-I Standard/Plus/Pro KSW VarioSens Infineon SRF55Vxx Transponder (Read/Write with Blocksize 8) Switch ON/OFF use of Infineon Customer Commands Switch ON/OFF automatic use of Advanced Mode Switch ON/OFF automatic use of Fujitsu Fast Commands Signaling Stable Inventory performance with 8 TS for Icode 1. V1.06(USB) ( ) KSW VarioSens improvements Support ICode SLI S Mandatory Commands. Improvement of reliability for Inventory command regarding ICode SLI transponders Improvement of reliability for Inventory command regarding ICode 1 transponders Support for Read Multiple Block command with more than 32 blocks á 4 Byte (max. 99 blocks á 4 Byte) FEIG ELECTRONIC GmbH Page 4 of 12 SWRN MR_PR_PRH101.doc

5 V1.07(USB) ( ) Support ICode SLI S Customer Commands Support EM Marin 4034 Support Fujitsu MB89R119 Support ST LRI2k Support ST LRI512 EAS Command V2.01(USB) ( ) Support ICode SLI-S and ICode SLI-L. Support EM4322 Support ST M24LR64 Improvement of reliability for Write AFI command concerning ICode SLI-S and ICode SLI-L Support of Reader Login and Reader Configuration Access conditions for configuration pages Turn off RF Power automatically (configurable) Reserved configuration page for customer purposes Start/Stop of Scan Mode possible via command [0x6A] RF OnOff V2.02(USB) ( ) Improvement of new Reader Configuration Access function Improvement of USB communication Serial-Reader V1.02(A) ( ) First Customer Release Version: V1.03(A) ( ) FEIG ELECTRONIC GmbH Page 5 of 12 SWRN MR_PR_PRH101.doc

6 V1.04(A) ( ) New Transponder Customer Commands Fujitsu Fast Commands (MB89R118 Tags). TI Tag-it HF-I Standard/Plus/Pro KSW VarioSens Infineon SRF55Vxx Transponder (Read/Write with Blocksize 8) Switch ON/OFF use of Infineon Customer Commands Switch ON/OFF automatic use of Advanced Mode Switch ON/OFF automatic use of Fujitsu Fast Commands Signaling Stable Inventory performance with 8 TS for Icode 1. V1.05(A) ( ) Improvement of reliability for Inventory command regarding ICode SLI transponders Improvement of reliability for Inventory command regarding ICode 1 transponders V1.06(A) ( ) Support ICode SLI S Mandatory Commands Improvements KSW VarioSens Support for Read Multiple Block command with more than 32 blocks á 4 Byte (max. 99 blocks á 4 Byte) V1.07(A) ( ) Support ICode SLI S Customer Commands Support EM Marin 4034 Support Fujitsu MB89R119 Support ST LRI2k Support ST LRI512 EAS Command FEIG ELECTRONIC GmbH Page 6 of 12 SWRN MR_PR_PRH101.doc

7 V2.01(A) ( ) Support ICode SLI-S and ICode SLI-L. Support EM4322 Support ST M24LR64 Improvement of reliability for Write AFI command concerning ICode SLI-S and ICode SLI-L Support of Reader Login and Reader Configuration Access conditions for configuration pages Turn off RF Power automatically (configurable) Reserved configuration page for customer purposes Start/Stop of Scan Mode possible via command [0x6A] RF OnOff V2.02(A) ( ) Improvement of new Reader Configuration Access function FEIG ELECTRONIC GmbH Page 7 of 12 SWRN MR_PR_PRH101.doc

8 History of Firmware Revisions (RF-Controller) PRH101 USB-Reader V1.01(USB) ( ) Initial Version: V1.02(USB) ( ) First Customer Release Version: V1.06(USB) ( ) KSW VarioSens Infineon SRF55Vxx Transponder (Read/Write with Blocksize 8) Support ICode SLI S Mandatory Commands. Improvement of reliability for Inventory command regarding ICode SLI transponders Improvement of reliability for Inventory command regarding ICode 1 transponders Fujitsu Fast Commands (MB89R118 Tags). TI Tag-it HF-I Standard/Plus/Pro Support for Read Multiple Block command with more than 32 blocks á 4 Byte (max. 99 blocks á 4 Byte) V1.07(USB) ( ) Support ICode SLI S Customer Commands Support EM Marin 4034 Support Fujitsu MB89R119 Support ST LRI2k Support ST LRI512 EAS Command V2.01(USB) ( ) Support ICode SLI-S and ICode SLI-L. Support EM4322 Support ST M24LR64 FEIG ELECTRONIC GmbH Page 8 of 12 SWRN MR_PR_PRH101.doc

9 Improvement of reliability for Write AFI command concerning ICode SLI-S and ICode SLI-L Support of Reader Login and Reader Config Access conditions for configuration pages Turn off RF Power automatically (configurable) Reserved config page for customer purposes Start/Stop of Scan Mode possible via command [0x6A] RF OnOff Serial-Reader V1.02(A) ( ) First Customer Release Version (Initial Version) V1.03(A) ( ) V1.06(A) ( ) Support ICode SLI S Mandatory Commands. Improvement of reliability for Inventory command regarding ICode SLI transponders Improvement of reliability for Inventory command regarding ICode 1 transponders New Transponder Customer Commands Fujitsu Fast Commands (MB89R118 Tags). TI Tag-it HF-I Standard/Plus/Pro KSW VarioSens Infineon SRF55Vxx Transponder (Read/Write with Blocksize 8) Support for Read Multiple Block command with more than 32 blocks á 4 Byte (max. 99 blocks á 4 Byte) Switch ON/OFF use of Infineon Customer Commands Switch ON/OFF automatic use of Advanced Mode Switch ON/OFF automatic use of Fujitsu Fast Commands V1.07(A) ( ) Support ICode SLI S Customer Commands Support EM Marin 4034 Support Fujitsu MB89R119 Support ST LRI2k Support ST LRI512 EAS Command FEIG ELECTRONIC GmbH Page 9 of 12 SWRN MR_PR_PRH101.doc

10 V2.01(A) ( ) Support ICode SLI-S and ICode SLI-L. Support EM4322 Support ST M24LR64 Improvement of reliability for Write AFI command concerning ICode SLI-S and ICode SLI-L Support of Reader Login and Reader Configuration Access conditions for configuration pages Turn off RF Power automatically (configurable) Reserved configuration page for customer purposes Start/Stop of Scan Mode possible via command [0x6A] RF OnOff Bluetooth-Reader V1.00(B) ( ) Initial Version: V1.03(B) ( ) Bluetooth Interface:: Improvements regarding the detection and connection of the reader. New Transponder Customer Commands Fujitsu Fast Commands (MB89R118 Tags). TI Tag-it HF-I Standard/Plus/Pro KSW VarioSens Infineon SRF55Vxx Transponder (Read/Write with Blocksize 8) Switch ON/OFF use of Infineon Customer Commands Switch ON/OFF automatic use of Advanced Mode Switch ON/OFF automatic use of Fujitsu Fast Commands Signaling Stable Inventory performance with 8 TS for Icode 1. FEIG ELECTRONIC GmbH Page 10 of 12 SWRN MR_PR_PRH101.doc

11 V1.06(B) ( ) Improvements KSW VarioSens Support Icode SLI S Mandatory Commands. Improvement of reliability for Inventory command regarding ICode SLI transponders Improvement of reliability for Inventory command regarding ICode 1 transponders Support for Read Multiple Block command with more than 32 blocks á 4 Byte (max. 99 blocks á 4 Byte) V1.07(B) ( ) Support ICode SLI S Customer Commands Support EM Marin 4034 Support Fujitsu MB89R119 Support ST LRI2k Support ST LRI512 EAS Command V2.01(B) ( ) Support ICode SLI S and ICode SLI L Support EM4322 Support ST M24LR64 Improvement of reliability for Write AFI command concerning ICode SLI-S and ICode SLI-L Support of Reader Login and Reader Configuration Access conditions for configuration pages Turn off RF Power automatically (configurable) Reserved configuration page for customer purposes Start/Stop of Scan Mode possible via command [0x6A] RF OnOff FEIG ELECTRONIC GmbH Page 11 of 12 SWRN MR_PR_PRH101.doc

12 History of Firmware Revisions (USB-Controller) V1.00 ( ) Initial Version: no Scan Mode supported V1.01 ( ) Scan Mode (HID-Mode): Scan Mode supported V1.02 ( ) Update-Function Firmware RF-Controller: Timeout Time modified. V1.03 ( ) Function Firmware RF-Controller: Improvements regarding the enumeration with USB 2.0 V1.04 ( ) Function Firmware RF-Controller: Improvements regarding the update routine with USB 2.0 V1.05 ( ) Scan Mode (HID-Mode): FEIG ELECTRONIC GmbH Page 12 of 12 SWRN MR_PR_PRH101.doc