APPLICATION-NOTE. OBID i-scan ID ISC.M02-B. Firmware Update. from Firmware Version 1.1 and higher. final public (B) N e-ID-B.

Transcription

1 OBID i-scan APPLICATION-NOTE ID ISC.M02-B Firmware Update from Firmware Version 1.1 and higher final public (B) N e-ID-B.doc

2 Copyright 2003 by FEIG ELECTRONIC GmbH Lange Strasse 4 D Weilburg-Waldhausen Tel.: Note With the edition of this document, all previous editions become void. Indications made in this manual may be changed without previous notice. Copying of this document, and giving it to others and the use or communication of the contents thereof are forbidden without express authority. Offenders are liable to the payment of damages. All rights are reserved in the event of the grant of a patent or the registration of a utility model or design. Composition of the information in this document has been done to the best of our knowledge. FEIG ELECTRONIC GmbH does not guarantee the correctness and completeness of the details given in this manual and may not be held liable for damages ensuing from incorrect or incomplete information. Since, despite all our efforts, errors may not be completely avoided, we are always grateful for your useful tips. The instructions given in this manual are based on advantageous boundary conditions. FEIG ELECTRONIC GmbH does not give any guarantee promise for perfect function in cross environments. FEIG ELECTRONIC GmbH assumes no responsibility for the use of any information contained in this document and makes no representation that they free of patent infringement. FEIG ELECTRONIC GmbH does not convey any license under its patent rights nor the rights of others. OBID i-scan is registered trademark of FEIG ELECTRONIC GmbH. OBID is registered trademark of FEIG ELECTRONIC GmbH. Windows is a registered trademark of Microsoft Corporation General information's regarding this document The sign " " indicates extensions or changes of this manual compared with the former issue. FEIG ELECTRONIC GmbH Page 2 of 17 N e-ID-B.doc

3 Content 1. Introduction Programming of the Firmware using Terminal-Program Hyper Terminal Required components Hardware preparation Hyper Terminal Start Software-Flash-Loader Start and configuration of the Hyper Terminal Programming of the Firmware Firmware VERIFY and RESET Programming with the Hardware-Flash-Loader (FUJITSU FLASH MCU Programmer) Needed components Hardware setting ID ISC.M Programming the Software-Flash-Loaders with FUJITSU FLASH MCU Programmer Start FUJITSU FLASH MCU Programmer with flash.exe Port configuration Select target Load file Programming Firmware Error Messages FEIG ELECTRONIC GmbH Page 3 of 17 N e-ID-B.doc

4 1. Introduction The firmware of the ID ISC.M02 is stored in a flash memory chip. This allows you to perform firmware updates through the serial RS232 (TTL) port of the Reader. To perform the software update using the software flash loader you will need a terminal program. We recommend the terminal program Hyper Terminal, which already exist in a Windows operating system. You can also use any other terminal program which supports the -Modem protocol. Note: On condition that there is already installed the firmware version 1.01 (or higher) the terminal program can be used to perform a firmware update. 2. Programming of the Firmware using Terminal-Program Hyper Terminal The software flash-loader can be started e.g. by using the demoprogram ID ISOStart. The command [0x55] Start Flash Loader must be transferred over the RS232 (TTL) interface. After receiving an OK, the program ID ISOStart must be closed and the Hyper Terminal can be started to perform the firmware update. FEIG ELECTRONIC GmbH Page 4 of 17 N e-ID-B.doc

5 2.1. Required components Required components -Modem capable Terminal Program (e.g. Hyper Terminal) RS232-TTL converter e.g. model 232LPTTL B&B Electronic Ltd ( 5V DC Powersuppply ID Net.5V Connection cable ID CAB.RS-A or self-made Adapter-cable self made ID ISC.M02 ID ISC.M02-B B&B Electronic Ltd Four-Channel RS-232 to TTL/CMOS Converter Modell 232LPTTL FEIG ELECTRONIC GmbH Page 5 of 17 N e-ID-B.doc

6 2.2. Hardware preparation 1. Switch OFF the power supply of the Readers ID ISC.M02-B. 2. Connect the RS 232 / TTL converter to the serial RS232 Port of the PCs. 3. The TTL-output of the converter must be connected with the connector 1. For this you have to use the connection cable (see picture). 4. Switch ON the power supply. male connector 9Pin female connector 9Pin male connector 9Pin female connector 9Pin Powersupply connector PC RD TD Ground RTS CTS RS232 to TTL Four-Channel RS-232 to TTL/CMOS Converter B&B Model 232LPTTL Connection cable ID CAB.RS-A male connector 9Pin female connector 9Pin Adapter cable V1 V2 4 1 J1 C73 J2 2 J3 C65 3 FEIG ELECTRONIC GmbH Page 6 of 17 N e-ID-B.doc

7 2.3. Hyper Terminal Hyper Terminal is a accessory of the Windows operating system. You will find it under Programs / Accessories / Communication. If it is not so, you can install it using the Windows CD-ROM. Further information s you will find in the description of the Windows operating system Start Software-Flash-Loader To start the software flash loader in the Reader, you must use the command [0x55] Start Flash Loader using the ID ISOStart demo program.!please use only the Bus-Address which is currently programmed in the reader (Defauld: 0 ). In the case of using the Bus-Address 255 the error message: Errorcode: appears and the Software Flashloader will not start! After confirming with OK, you must quit the demo program ID ISOStart Start and configuration of the Hyper Terminal. 1. Start the Hyper-Terminal Program from the Start menu Programs / Accessories / Communication. FEIG ELECTRONIC GmbH Page 7 of 17 N e-ID-B.doc

8 Create a new connection, give a name (e.g. Update ID ISC.M02) and choose a symbol for the connection. If there already exist a configuration you can press close and open the existing configuration file using the Hyper Terminal Menu File / Open. Please choose in the following dialog the used COM- Port and press OK. Configure the used COM-Port in the COM Propertiesmenu: Bits per second Baud Data bits: 8 Parity: None Stop bits: 1 Flow control: non FEIG ELECTRONIC GmbH Page 8 of 17 N e-ID-B.doc

9 If the message: Unable to open COM1..., appears after pressing the OK -button, there is possibly a different program active, which uses the COM-Port. Please check if the demoprogram ID ISOStart is still running and complete it if necessary Programming of the Firmware To check the connection please press the Return-button once. Now the prompt Bootloader with the current firmware version should appears. Beside the prompt you have to write: FLASHALL, in capital letters. After sending the command FLASHALL it is not allowed to interrupt the power supply of the reader! This will be receipted with the response ERASE WAIT. After a few seconds you will be requested by the message Start DOWNLOAD to send the new firmwaremhx-file to the reader. To do this you have about 2 minutes time. In this period of time every 5 seconds the signs C resp. will appear. If you don t send a mhx-file to the reader during this period of time, the error message ERROR 1 will appear. After that you have to send the FLASHALL -command again. Don t switch off the reader. By pressing the Send button you can call the dialog function Send file. FEIG ELECTRONIC GmbH Page 9 of 17 N e-ID-B.doc

10 Ensure that the protocol is selected as modem and choose the new firmware.mhx file. Press the Send button. The following programming procedure will be displayed in a window. This will take a few seconds. The successful programming procedure will be answered with an OK. FEIG ELECTRONIC GmbH Page 10 of 17 N e-ID-B.doc

11 Firmware VERIFY and RESET To ensure that there was no error while the programming procedure you can compare the programmed firmware with the original mhx-file using the command VERIFY. Please write the command VERIFY beside the prompt and choose again the mhx-file by press the Send button. Was the process also confirmed with "OK" you can perform a CPU Reset by using the command RESET. If the LEDs are flashing alternating after a Reset you have to switch off and on the reader again. Now only the green LED should flashing. Now the programming of the new firmware is finished. Please complete the Hyper Terminal and check the reader functions using the demoprogram ID ISOStart. FEIG ELECTRONIC GmbH Page 11 of 17 N e-ID-B.doc

12 3. Programming with the Hardware-Flash-Loader (FUJITSU FLASH MCU Programmer) The hardware flash loader should only be used if the software flash loader is faulty. To activate the hardware flash loader you have to fit a jumper. Follow the instruction in chapter 2.2. Hardware preparation resp Hardware setting ID ISC.M Needed components Needed components Program: FUJITSU FLASH MCU Programmer RS232-TTL converter e.g. Model 232LPTTL B&B Electronic Ltd ( Power supply ID Net.5V ID ISC.M02 Connection cable ID CAB.RS-A or self made Adapter-cable self made FEIG ELECTRONIC GmbH Page 12 of 17 N e-ID-B.doc

13 3.2. Hardware setting ID ISC.M02 1. Switch OFF the power supply of the Readers ID ISC.M02-B. 2. Connect the RS 232 / TTL converter to the serial RS232 Port of the PCs. 3. The TTL-output of the converter must be connected with the connector 1. For this you have to use the connection cable (see picture). 4. The jumper J1 must be changed from position 1-2 to position Switch on the reader and follow the description in chapter : Start FUJITSU FLASH MCU Programmer with flash.exe. male connector 9Pin female connector 9Pin male connector 9Pin female connector 9Pin Powersupply connector PC RD TD Ground RTS CTS RS232 to TTL Four-Channel RS-232 to TTL/CMOS Converter B&B Model 232LPTTL Connection cable ID CAB.RS-A J1 male connector 9Pin female connector 9Pin Adapter cable V1 V Setting for Firmware Update 1 J1 C73 J2 2 J3 C65 3 FEIG ELECTRONIC GmbH Page 13 of 17 N e-ID-B.doc

14 3.3. Programming the Software-Flash-Loaders with FUJITSU FLASH MCU Programmer. Please install the FUJITSU FLASH MCU Programmer by a double click onto PCW16setup.exe. After turning on the Reader, you can immediately start the Windows program flash.exe inside the folder FMC16L. No operational firmware is necessary in the flash memory for using the hardware flash loader. You can quit the hardware flash loader by turning off the Reader or doing a rest without any loss of memory in the flash chip before the firmware has been erased using flash.exe Start FUJITSU FLASH MCU Programmer with flash.exe Turn the Reader off and set the jumpers as described in Section 3.2. Hardware setting ID ISC.M02 or Turn the Reader back on.!the program FUJITSU FLASH MCU Programmer must be started from a hard disk. Also the MH-File must be stored on the writeable hard disk. Please check that the file and the program is not write protected. Make all settings as described in the following Section Port configuration Port configuration After starting for the first time you should check the configuration of the serial RS232 port you are using. To do this select the corresponding COM Port. For this you should press the Set Environment - button and select the used COM-Port. FEIG ELECTRONIC GmbH Page 14 of 17 N e-ID-B.doc

15 Select target Select MB90F562/B as the target, i.e. CPU and select the Crystal Frequency of 4 MHz. If you have selected a wrong CPU, an error messages will be displayed and the delete and programming routines will not function properly Load file The file with the new firmware xxxxxx.mhx is on the CD-ROM or can be obtain via from FEIG ELECTRONIC GmbH. Select the file using the Open -button. Valid files have the suffix MH Programming Firmware To start the programming process press Full Operation(D+E+B+P). When executing the function all the necessary steps are automatically carried out. You can also perform these steps individually if desired. Programming progress is displayed in a window. If programming was successful a message box appears: After programming is complete, you must remove the jumpers and set the DIP-switch back to default position. If the LEDs are flashing alternating after switching on the reader you have to switch off and on the reader again. FEIG ELECTRONIC GmbH Page 15 of 17 N e-ID-B.doc

16 3.4. Error Messages No.001 Download error*1 Cause:Downloading failed Action:Return the folder and file configurations to the installation defaults. No.003 Timeout error Cause:The microcontroller does not respond. (Not changed to flash memory reprogramming mode) Action:Recheck the setting of pins used for reprogramming flash memory. No.006COM port open error Cause:The COM port is disabled. Action:Enable the COM port. No.007 Download file open error Cause:m_flash.xxxnot found Action:Return the folder and file configurations to the installation defaults. No.008 File size get error Cause:File access failed Action:Check whether the PC is unstable. No.009 COM port setting information get error Cause:The COM port is disabled. Action:Enable the COM port. No.010 COM port setting information change error Cause:The COM port is disabled. Action:Enable the COM port. No.011 Communication error Cause:The microcontroller returned a communication error. Action:Re-execute the command or replace the chip. No.012 Read error Cause:Data cannot be read from flash memory in the microcontroller. Action:Re-execute the command or replace the chip. FEIG ELECTRONIC GmbH Page 16 of 17 N e-ID-B.doc

17 No.013 Write error Cause:Data cannot be programmed to flash memory in the microcontroller. Action:Re-execute the command again or replace the chip. No.015 COM port write error Cause:The COM port is disabled. Action:Check the RS-232C cable connected to the COM port. No.016 COM port read error Cause:The COM port is disabled. Action:Check the RS-232C cable connected to the COM port. No.017 File access error Cause:m_flash.xxxnot read Action:Return the folder and file configurations to the installation defaults. No.018 Erase error *1 Cause:Erasing failed Action:Return the folder and file configurations to the installation defaults. No.101 Set hex file. Cause: Hex file not set Action:Set hex file in the dialog box. No.102 Batch command error Cause:An error occurred at batch command execution Action:Return the folder and file configurations to the installation defaults. No.103 Invalid hex file Cause:The selected hex file is invalid. Action:Select the Motorola-S format file as the hex file. No.207 Memory allocation error Cause:Unable to allocate memory for execution Action:Quit any running application and retry. FEIG ELECTRONIC GmbH Page 17 of 17 N e-ID-B.doc