RCN155-L, RCN151-L Room controller

Transcription

1 Issue Datasheet EN Room controller pplication The is a room controller for stand-alone use or use in a LON network. For direct communication with other LON components, the is equipped with an integrated LON FTT10 interface. The room controller RCN155-L, RCN151-L can be expanded with operating modules. The room controller conforms to LON Works standard 2.0. This means that no additional costs are incurred for LON Works Credits during commissioning. Content Page Important Information Regarding Product Safety...2 Item...3 Technical Data...3 Compatibility...4 ccessories (not included in delivery)...5 Dimensions...5 Connection...6 Connection examples...7 ounting...10 Removal...11 Network Installation...12 Änderungen vorbehalten - Contents subject to change - Sous réserve de modifications - Reservado el derecho a modificación - Wijzigingen voorbehouden - Con riserva di modifiche - Innehåll som skall ändras - Změny vyhrazeny - Zmiany zastrzeżone - Возможны изменения - változtatások jogát fenntartjuk - Kieback&Peter GmbH & Co. KG Tempelhofer Weg 50, Berlin/Germany Telefon: , Telefax: info@kieback-peter.com

2 Datasheet EN Issue Important Information Regarding Product Safety Safety Instructions This data sheet contains information on installing and commissioning the product "RCN155-L, RCN151-L". Each person who carries out work on this product must have read and understood this data sheet. If you have any questions that are not resolved by this data sheet, you can obtain further information from the supplier or manufacturer. If the product is not used in accordance with this data sheet, the protection provided will be impaired. pplicable regulations must be observed when installing and using the device. Within the EU, these include regulations regarding occupational safety and accident prevention as well as those from the VDE (ssociation for Electrical, Electronic & Information Technologies). If the device is used in other countries, it is the responsibility of the system installer or operator to comply with local regulations. ounting, installation and commissioning work on the devices may only be carried out by qualified technicians. Qualified technicians are persons who are familiar with the described product and who can assess given tasks and recognize possible dangers due to technical training, knowledge and experience as well as knowledge of the appropriate regulations. Legend WRNING Indicates a hazard of medium risk which can result in death or severe bodily injury if it is not avoided. CUTION Indicates a hazard of low risk which can result in minor or medium bodily injury if it is not avoided.! CUTION Indicates a hazard of medium risk which can result in material damage or malfunctions if it is not avoided. NOTE Indicates additional information that can simplify the work with the product for you. Notes on Disposal For disposal, the product is considered waste from electrical and electronic equipment (electronic waste) and must not be disposed of as household waste. Special treatment for specific components may be legally binding or ecologically sensible. The local and currently applicable legislation must be observed. Page 2 / 12

3 Issue Datasheet EN Item RCN155-L RCN151-L Room controller with 6 inputs and 11 outputs Room controller with 6 inputs and 8 outputs Technical Data Nominal voltage C 110 to 230 V ± 10 %; 50 Hz to 60 Hz; 18 V (consumption <1 W) Inputs Outputs starting current: 50 / C 230 V; 1 ms (I 2 t -value = s) 6 configurable inputs 2x KP10 or binary inputs P1, P2 2x NTC10K or binary inputs P3, P4 2x V or binary inputs P5, P6 2 BO: PW output or 3-point actuator; K1, K2 floating; C 24 V or C 230 V (Σ 400 m) 2x 1 W small thermoactuator C/DC 24 V; ST40405/80 or 4x 1 W small thermoactuator C 230 V; ST20405/80 1 BO: 1 binary output, floating relay contact K10; C 230 V (2 KW) / C 24 V, 10 3 BO: relay contact C 230 V, 3 ; K7, K8, K9 2 BO: relay contact C 230 V, 3 ; K5, K6 (not used with RCN151-L) 1 O: V; maximum 2.5 m; Y4 1 O: V; maximum 2.5 m; Y1 DC 24 V power supply (not used with RCN151-L) Σ 2 W 1 O: V; maximum 2.5 m; Y2 DC 24 V power supply Σ 2W NOTE s the thermo actuator PR42405 cannot be supplied with voltage via terminal assignments 23 and 26, an external power supply (configuration 8 W with 24 V per actuator) is needed. The RCN155-L does not support the PR Indicators and controls Green LED: Operation Red LED: LON status Push-button: LON Service Pin Interfaces LON FTT-10/FTT kbit/s plug-in screw terminal CN 4 poles for the connection with room modules RBW20x-C or RBW30x-C, screw terminals or RJ9 (20 m max.) power supply (internal) for DC 12 V room controllers Connection cross slot screw terminal, 2.5 mm 2 max. single-wired or multi-wired 0.34 mm 2 to 2.5 mm 2 WG Overvoltage category III Level of contamination 2 Page 3 / 12

4 Datasheet EN Issue Rated impulse withstand 4000 V voltage ode of operation Type 1 Housing Plastic; self-extinguishing according to UL94 V-0 Protection class This device is intended for installation in a wall-mounted enclosure or switch cabinet with protection class I or II. Degree of protection IP20 mbient temperature 0 C to 50 C mbient humidity During operation: 20 to 80 % relative humidity; non-condensing Out of operation: 5 to 90 % relative humidity; non-condensing Storage temperature -25 C to +55 C (class 1K3) Installation ounting rail TH Weight 0.3 kg Dimensions x 90 x 60 (WxHxD in mm) Certification eu.bac Cert rticle License No. pplication C-value (K) RCN151-L Fan Coil Unit Systems (4 pipes) (0 V to10 V) Fan Coil Unit Systems (2 pipes 2 wires) (0 V to 10 V) Fan Coil Unit Systems (4 pipes) (PW) Fan Coil Unit Systems (2 pipes 2 wires) (PW) RCN155-L Fan Coil Unit Systems (4 pipes) (0 V to 10 V) Fan Coil Unit Systems (2 pipes 2 wires) (0 V to 10 V) Fan Coil Unit Systems (4 pipes) (PW) Sensor types Type Value range and unit 0 to 10 V 0 to 100 % KP10-40 to 60 C NTC10K (NTC10K31) -40 to 60 C NTC10K (FCD; NTC103T-2,3) -40 to 60 C Resistor (potentiometer) 0 to 10 kω Compatibility Room controller RBW20x-C, RBW30x-C Fan Coil Unit Systems (2 pipes 2 wires) (PW) Page 4 / 12

5 Issue Datasheet EN ccessories (not included in delivery) Z178 Connection line: room control module and room controller (10 m) Z178/2 dapter: RJ9 plug - terminal block, 4-pole (15 cm) HW HW HW Z180 Solid state relay input voltage 18 to 36 V C/DC Solid state relay input voltage 90 to 280 V C Empty housing for wall mounting (8TE/IP30) Housing for wall mounting Installation space: one row, 324 mm (18 HP); 1 Dimensions 90,0 44,7 143,5 60,0 Page 5 / 12

6 Datasheet EN Issue Connection RCN155-L Y4 max. 0,4 K1 K2 10 K10 3 (2 ) K7 K8 K9 3 (2 ) K5 K6 N L Y1 Y2 +24V +24V P5 P6 P1 P2 P3 P KP10 NTC10K RCN151-L B LON +12V= C+ C CN RJ Y4 max. 0,4 K1 K2 10 K10 3 (2 ) K7 K8 K9 N L Y2 +24V P5 P6 P1 P2 P3 P KP10 NTC10K + B LON +12V= C+ C CN RJ Inputs P5, P6 I: V or BE: Binary (floating) P1, P2 I: KP10 or BE: Binary (floating) P3, P4 I: NTC10K or potentiometer 10 kω or BE: Binary (floating) Page 6 / 12

7 Issue Datasheet EN Outputs K1, K2 BO: Thermo actuator or 3-point actuator; max. C 230 V, 400 m K10 BO: Electric heating or light; max. C 230 V, 10, switch-on current max. 40 (corresponds to 2 typical conventional ballasts for fluorescent lamps) K7.. K9 BO: aximum 3-level fan; max. C 230 V, 3 K5, K6 BO: 3-point actuator; max. C 230 V, 3 (not used with RCN 151-L) Y4 O: 0 to 10 V, analog fan control; 2.5 m maximum Y1 O: V, valve or damper control; maximum 2.5 m; DC 24 V, 1 W power supply (not used with RCN151-L) Y2 O: V, valve or damper control; maximum 2.5 m; DC 24 V power supply Σ 2W Connection examples - Valve/fan C 230 V - Ventilation damper N L1 St Y4 K1 K2 K10 K7 K8 K9 K5 K Y1 +24V Y2 +24V P5 P6 P1 P2 P3 P KP10 NTC10K 0..1 B LON +12V= C+ C CN RJ Page 7 / 12

8 Datasheet EN Issue ! - connecting accessory CF071KD (RC element as additional suppressor circuit) CUTION Higher loads can occur at the relay output when switching fan motors, possibly resulting in high strain on the relays (observe the fan's data sheet!). When in doubt, a suppressing RC element is recommended per fan level to avoid malfunctions and damage to the room controller (accessory: CF071KD). N N L1 St x CF071KD L x Valve output as 3-point C 24 to 230 V - nalog fan 0..1 D15 D15 N N L Y4 K1 K2 K10 K7 K8 K9 K5 K Y1 Y2 +24V +24V P5 P6 P1 P2 P3 P KP10 NTC10K B LON +12V= C+ C CN RJ Page 8 / 12

9 Issue Datasheet EN - Sensor Y1 Y2 +24V +24V TDF14 KP Y1 Y2 +24V +24V 0,8W H% HTF12 KP10 10 NOTE connection of the potentiometer is only possible at the entrances P3 or P4, at terminals "33", "34" and "34", "35" and with the software version 1.60 or higher. Page 9 / 12

10 Datasheet EN Issue ounting WRNING Danger of death by electrocution. ount or remove only when power is switched off. TH Page 10 / 12

11 Issue Datasheet EN Removal WRNING Danger of death by electrocution. ount or remove only when power is switched off Page 11 / 12

12 Datasheet EN Issue Network Installation When commissioning a room controller in the "Lonaker Integration Tool", the unique Neuron ID of a real room controller is defined for a device in the drawing. You can find the Neuron ID in text form and as a barcode on the type plate and on the supplied configuration labels. You have the following options for entering the Neuron ID in the "Lonaker Integration Tool": anually: Enter the Neuron ID using the computer keyboard. Barcode: Scan the Neuron ID using a barcode scanner. Online: Receive the Neuron ID via the LON network. The computer with the network management tool must be connected to the LON network. The Neuron ID is transmitted when the service pin is entered on the room controller or when a magnet is used on a connected operator panel Service PIN 2 Service LED eanings of the "Service LED" (2) Red-green LED flashing: "Service PIN" (1) pressed Red LED flashing: Not commissioned Green LED: Commissioned Online installation on the room control module RBW20x-C or RBW30x-C: The technolon room controller can also be identified quickly and easily directly on the room control module using a magnet (3). magnet (3) is guided along the right side of room control module RBW20x-C or RBW30x-C. Internally, this triggers the service PIN in the RCN room controller. To verify this, a service LED (4) on the top part of the housing on the room control modules lights up green RBW205-C RBW305-C Page 12 / 12