CLK+ CLK- Expansion Interface TX+ TX-
|
|
|
- Barrie Jefferson
- 5 years ago
- Views:
Transcription
1 REV INTRODUCTION XR17V358/354 EVALUATION BOARD USER S MANUAL This user s manual is for the XR17V358/354 evaluation board. The XR17V358 and XR17V354 are available in the same package and are pin compatible, therefore they share the same evaluation board. This user s manual gives an overview of the evaluation board and the jumper settings for testing various modes using the evaluation board. 2.0 OVERVIEW This evaluation board has a x1 PCIe connector and will work in any x1, x4 or x16 PCIe slot. Up to 16 UART ports can be tested on this evaluation board when 2 XR17V358 are installed. The PCIe interface of the master device is connected directly to the PCIe connector. The master device communicates with the slave device via Exar s proprietary expansion interface. The PCIe interface on the slave device is not used. FIGURE 1. PCIE AND EXPANSION INTERFACE CLK+ CLK+ CLK- RX+ RX- XR17V358/354 Master Device Expansion Interface XR17V358/354 Slave Device CLK- RX+ RX- TX+ TX+ TX- TX- 2.1 Evaluation Board Components for Master Device The table below shows all of the components that are on the evaluation board for the master device. TABLE 1: COMPONENTS OF THE XR17V358 EVALUATION BOARD UNIT PART FUNCTION U2 XR17V358IB176-F XR17V354IB176-F XR17V358 or XR17V354 PCIe UART master device. U16 SP336EEY-L Exar RS-232/RS-485 Transceiver for master device UART channel 0. U11 SP336EEY-L Exar RS-232/RS-485 Transceiver for master device UART channel 1. U25 SP336EEY-L Exar RS-232/RS-485 Transceiver for master device UART channel 2. U24 SP336EEY-L Exar RS-232/RS-485 Transceiver for master device UART channel 3. U28 SP336EEY-L Exar RS-232/RS-485 Transceiver for master device UART channel 4. U27 SP336EEY-L Exar RS-232/RS-485 Transceiver for master device UART channel 5. U17 SP336EEY-L Exar RS-232/RS-485 Transceiver for master device UART channel 6. U22 SP336EEY-L Exar RS-232/RS-485 Transceiver for master device UART channel 7. U6 SP336EEY-L Exar RS-232/RS-485 Transceiver for master device UART RI# signals channels
2 XR17V358/354 EVALUATION BOARD USER S MANUAL REV TABLE 1: COMPONENTS OF THE XR17V358 EVALUATION BOARD UNIT PART FUNCTION U13 SP336EEY-L Exar RS-232/RS-485 Transceiver for master device UART RI# signals channels 4-7. U9 SP3497EEN-L Exar RS-485 Transceiver for master device UART channel 4. Not installed. U10 SP3497EEN-L Exar RS-485 Transceiver for master device UART channel 5. Not installed. U21 SP336EEY-L Exar RS-232/RS-485 Transceiver for master device UART channel 3 and 4 for RS-485 full-duplex testing. Not installed. U3 HSDL2300 IR Transceiver. Not installed. U29 SP6654EU-L Exar 800mA buck regulator. Not installed. U26 93C46 (PDIP) External EEPROM for storing Vendor ID and Device ID. Not programmed. U30 93C46 (TSSOP) External EEPROM for storing Vendor ID and Device ID. Not installed. 2.2 Evaluation Board Components for Slave Device The table below shows all of the components that are on the evaluation board for the slave device. If the slave device is not installed, then these components will also not be installed. TABLE 2: COMPONENTS OF THE XR17V358 EVALUATION BOARD UNIT PART FUNCTION U1 XR17V358IB176-F XR17V354IB176-F XR17V358 or XR17V354 PCIe UART slave device. U5 SP3245EEA-L Exar RS-232 Transceiver for slave device UART channel 0. U4 SP3245EEA-L Exar RS-232 Transceiver for slave device UART channel 1. U8 SP3245EEA-L Exar RS-232 Transceiver for slave device UART channel 2. U7 SP3245EEA-L Exar RS-232 Transceiver for slave device UART channel 3. U15 SP3245EEA-L Exar RS-232 Transceiver for slave device UART channel 4. U14 SP3245EEA-L Exar RS-232 Transceiver for slave device UART channel 5. U19 SP3245EEA-L Exar RS-232 Transceiver for slave device UART channel 6. U20 SP3245EEA-L Exar RS-232 Transceiver for slave device UART channel 7. U12 SP3497EEN-L Exar RS-485 Transceiver for slave device UART channel 4. U18 SP3497EEN-L Exar RS-485 Transceiver for slave device UART channel 5. U23 SP336EEY-L Exar RS-232/RS-485 Transceiver for slave device UART channel 3 and 4 for RS-485 full-duplex testing. Not installed. 2
3 REV XR17V358/354 EVALUATION BOARD USER S MANUAL 2.3 Jumper Settings for Power Sources for Master Device The following table shows the jumper settings for selecting/enabling the power source for the master device. TABLE 3: JUMPER SETTINGS FOR POWER SOURCES FOR MASTER DEVICE JUMPER J45 3.3V supply voltage for the 3.3V Core Jumper between 1&2 J42 Enables/Disables Internal Buck Regulator Jumper is not in - Internal buck regulator is enabled J66 3.3V supply voltage for the output stage of buck regulator Jumper between 1&2 J63 3.3V supply voltage for analog blocks of buck regulator Jumper between 1&2 J62 1.2V regulated voltage from internal buck Jumper between 1&2 J67 1.2V supply voltage for 1.2V PHY Jumper between 2&3 to use internal buck regulator J56 1.2V supply voltage for 1.2V Core Jumper between 2&3 to use internal buck regulator 2.4 Jumper Settings for Power Sources for Slave Device The following table shows the jumper settings for selecting/enabling the power source for the slave device. TABLE 4: JUMPER SETTINGS FOR POWER SOURCES FOR SLAVE DEVICE JUMPER J32 3.3V supply voltage for the 3.3V Core Jumper between 1&2 J31 Enables/Disables Internal Buck Regulator Jumper is not in - Internal buck regulator is enabled J68 3.3V supply voltage for the output stage of buck regulator Jumper between 1&2 J65 3.3V supply voltage for analog blocks of buck regulator Jumper between 1&2 J64 1.2V regulated voltage from internal buck Jumper between 1&2 J70 1.2V supply voltage for 1.2V PHY Jumper between 2&3 to use internal buck regulator J34 1.2V supply voltage for 1.2V Core Jumper between 2&3 to use internal buck regulator 2.5 Jumper/Switch Settings for RS-232 or RS-485 for Master Device The following table shows the setting for selecting between the RS-232 or RS-485 modes for the master device: TABLE 5: SETTINGS FOR RS-232 OR RS-485 MODE FOR MASTER DEVICE J13 3.3V Supply voltage pin for transceivers Not installed. Trace between 1&2. J41 Enable Auto RS-485 Half-Duplex Direction Control upon power-up Jumper between 1&2 enables this feature for all 8 channels. This feature can be disabled in the software after power-up. J54 Enable IR mode upon power-up Jumper between 1&2 enables this feature for all 8 channels. This feature can be disabled in the software after power-up. 3
4 XR17V358/354 EVALUATION BOARD USER S MANUAL REV TABLE 5: SETTINGS FOR RS-232 OR RS-485 MODE FOR MASTER DEVICE SW1 SW4 Selects between RS-232 and half-duplex RS-485 mode for UART channels 0 and 1 Selects between RS-232 and half-duplex RS-485 mode for UART channels 2 and 3 UART channel 0 RS-232 Mode (default) UART channel 0 half-duplex RS-485 Mode 2&15 Closed 3&14 Open 4&13 Closed UART channel 1 RS-232 Mode (default) UART channel 1 half-duplex RS-485 Mode 6&11 Open 7&10 Closed UART channel 2 RS-232 Mode (default) UART channel 2 half-duplex RS-485 Mode 2&15 Closed 3&14 Open 4&13 Closed UART channel 3 RS-232 Mode (default) UART channel 3 half-duplex RS-485 Mode 6&11 Open 7&10 Closed 4
5 REV XR17V358/354 EVALUATION BOARD USER S MANUAL TABLE 5: SETTINGS FOR RS-232 OR RS-485 MODE FOR MASTER DEVICE SW6 SW3 Selects between RS-232 and half-duplex RS-485 mode for UART channels 4 and 5 Selects between RS-232 and half-duplex RS-485 mode for UART channels 6 and 7 UART channel 4 RS-232 Mode (default) UART channel 4 half-duplex RS-485 Mode 2&15 Closed 3&14 Open 4&13 Closed UART channel 5 RS-232 Mode (default) UART channel 5 half-duplex RS-485 Mode 6&11 Open 7&10 Closed UART channel 6 RS-232 Mode (default) UART channel 6 half-duplex RS-485 Mode 2&15 Closed 3&14 Open 4&13 Closed UART channel 7 RS-232 Mode (default) UART channel 7 half-duplex RS-485 Mode 6&11 Open 7&10 Closed 5
6 XR17V358/354 EVALUATION BOARD USER S MANUAL REV TABLE 5: SETTINGS FOR RS-232 OR RS-485 MODE FOR MASTER DEVICE SW2 J14 J17 J16 J19 Enables the RI# signals in RS-232 mode for UART channels 0-7 Half-Duplex RS-485 control select for DE for UART channel 3 Half-Duplex RS-485 control select for RE# for UART channel 3 Half-Duplex RS-485 control select for DE for UART channel 4 Half-Duplex RS-485 control select for RE# for UART channel 4 UART channel 0 RS-232 Mode (default) UART channel 1 RS-232 Mode (default) No jumper installed enables RS-485 driver Jumper between 1&2 disables the RS-485 driver No jumper installed disables RS-485 receiver Jumper between 1&2 enables the RS-485 receiver No jumper installed enables RS-485 driver Jumper between 1&2 disables the RS-485 driver No jumper installed disables RS-485 receiver Jumper between 1&2 enables the RS-485 receiver 6
7 REV XR17V358/354 EVALUATION BOARD USER S MANUAL 2.6 Jumper Settings for RS-232 or RS-485 for Slave Device The following table shows the setting for selecting between the RS-232 or RS-485 modes for the slave device: TABLE 6: SETTINGS FOR RS-232 OR RS-485 MODE FOR SLAVE DEVICE J23 J29 3.3V supply voltage for RS-232 and RS-485 Transceivers for the slave device Enable Auto RS-485 Half-Duplex Direction Control upon power-up Jumper between 1&2 Jumper between 1&2 enables this feature for all 8 channels. This feature can be disabled in the software after power-up. J37 Enable IR mode upon power-up Jumper between 1&2 enables this feature for all 8 channels. This feature can be disabled in the software after power-up. J15 J18 J24 J28 Half-Duplex RS-485 control select for DE for UART channel 3 Half-Duplex RS-485 control select for RE# for UART channel 3 Half-Duplex RS-485 control select for DE for UART channel 4 Half-Duplex RS-485 control select for RE# for UART channel 4 No jumper installed enables RS-485 driver Jumper between 1&2 disables the RS-485 driver No jumper installed disables RS-485 receiver Jumper between 1&2 enables the RS-485 receiver No jumper installed enables RS-485 driver Jumper between 1&2 disables the RS-485 driver No jumper installed disables RS-485 receiver Jumper between 1&2 enables the RS-485 receiver 2.7 MPIO pins The MPIO pins of the both the master and slave devices are connected to LEDs or test points on the evaluation board. Refer to page 6 of the evaluation board schematic for details. 7
8 XR17V358/354 EVALUATION BOARD USER S MANUAL REV DRIVERS Software drivers for Windows and Linux are available from Exar. Send an with your driver request to uarttechsupport@exar.com. NOTICE EXAR Corporation reserves the right to make changes to the products contained in this publication in order to improve design, performance or reliability. EXAR Corporation assumes no responsibility for the use of any circuits described herein, conveys no license under any patent or other right, and makes no representation that the circuits are free of patent infringement. Charts and schedules contained here in are only for illustration purposes and may vary depending upon a user s specific application. While the information in this publication has been carefully checked; no responsibility, however, is assumed for inaccuracies. EXAR Corporation does not recommend the use of any of its products in life support applications where the failure or malfunction of the product can reasonably be expected to cause failure of the life support system or to significantly affect its safety or effectiveness. Products are not authorized for use in such applications unless EXAR Corporation receives, in writing, assurances to its satisfaction that: (a) the risk of injury or damage has been minimized; (b) the user assumes all such risks; (c) potential liability of EXAR Corporation is adequately protected under the circumstances. Copyright 2010 EXAR Corporation Datasheet January Send your UART technical inquiry with technical details to hotline: uarttechsupport@exar.com. Reproduction, in part or whole, without the prior written consent of EXAR Corporation is prohibited. 8
XR21V1410 EVALUATION BOARD USER S MANUAL 1.0 INTRODUCTION
1.0 INTRODUCTION This user s manual is for the XR21V1410 evaluation board. It will describe the hardware setup required to operate the part. 2.0 OVERVIEW The XR21V1410 evaluation board has one 16-QFN package
3.3V VIO_REF VCC XR21B1411 USBD- LOWPOWER J GND J10
REV..0.0 XRB_SP EVALUATION BOARD USER S MANUAL.0 INTRODUCTION This user s manual is for the XRB_SP evaluation board rev.. The XRB will be configured for the RS- mode when it is shipped from the factory.
TABLE 1: PACKAGE LIST. XRA1402IL16-F 16-pin QFN U7. XRA1402IG16-F 16-pin TSSOP U6. XRA1404IL16-F 16-pin QFN U7. XRA1404IG16-F 16-pin TSSOP U6
REV. 1.0.0 INTRODUCTION XRA1402/1404 EVALUATION BOARD USER S MANUAL This user s manual is for the XRA1402/1404 8-bit evaluation board. Table 1 shows the different devices and packages that the evaluation
XR21B1411 USER S MANUAL
REV. 1.0.0 WEB CONFIGURATION TOOL USER S MANUAL 1 WEB CONFIGURATION TOOL USER S MANUAL REV. 1.0.0 TABLE OF CONTENTS 1.0 OVERVIEW... 3 2.0 GPIO PIN CONFIGURATIONS... 3 2.1 CONFIGURING THE GPIO PINS IN GPIO
For more information about EEPROM, please refer to our DAN 112 that could be found at our website
REV. 1.0.0 1.0 INTRODUCTION XR16M654 & XR16M554 EVALUATION BOARD USER S MANUAL This user s manual is for both the XR16M654 and the XR16M554 evaluation board. Since it can be used for both XR16M654 and
January 2014 Rev FEATURES
January 2014 Rev. 1.1.0 GENERAL DESCRIPTION In some applications it would be more desirable to download a runtime image from a micro controller onto RAM than to store a configuration into flash memory.
DATA COMMUNICATIONS APPLICATION NOTE DAN132
EXAR S SINGLE CHANNEL UARTS COMPARED WITH TI S TL16C550C June 2002 Author: PY 1.0 INTRODUCTION This application note describes the major difference between Exar s ST16C550, ST16C580, ST16C650A, and XR16C850
DATA COMMUNICATIONS APPLICATION NOTE DAN133
EXAR S QUARTS COMPARED WITH TI S TL16C554 AND TL16C554A June 2002 Author: PY 1.0 INTRODUCTION This application note describes the major difference between Exar s QUARTs (ST16C554, ST16C654, and XR16C854)
GENERAL DESCRIPTION FEATURES
January 2010 Rev. 1.0.1 GENERAL DESCRIPTION The is designed to allow individuals to program the NVM (Non-Volatile Memory) in the XRP7704, XRP7708, XRP7740, and XRP7714. The board consists of a microcontroller
DATA COMMUNICATIONS APPLICATION NOTE DAN137
November 2003 EXAR XR16L580 COMPARED WITH TI S TL16C550C (48-TQFP) Author: BL & PY 1.0 INTRODUCTION This application note describes the major differences between Exar s XR16L580 and TI s TL16C550C (PT
DATA COMMUNICATIONS APPLICATION NOTE DAN170
AUGUST 2004 MIGRATING TO EXAR S FIFTH GENERATION UARTS: XR16L784/788 Author: BL 1.0 INTRODUCTION This application note provides sytem design engineers with the information necessary to migrate to Exar
XR-2206/2211/2212. Evaluation System User Manual
...the analog plus company TM XR-2206--2ES November 996-4 XR-2206/22/222 Evaluation System User Manual Rev..00 996 EXAR Corporation, 48720 Kato Road, Fremont, CA 94538 (50) 668-7000 FAX (50) 668-707 XR-2206--2ES
XRA BIT I2C/SMBUS GPIO EXPANDER WITH INTEGRATED LEVEL SHIFTERS
SEPTEMBER 2011 REV. 1.0.0 GENERAL DESCRIPTION The XRA1207 is a 16-bit GPIO expander with an I 2 C/ SMBus interface. After power-up, the XRA1207 has internal 100K ohm pull-up resistors on each pin that
XRA1201/1201P 16-BIT I2C/SMBUS GPIO EXPANDER
SEPTEMBER 2011 REV. 1.0.0 GENERAL DESCRIPTION The XRA1201/1201P is a 16-bit GPIO expander with an I 2 C/SMBus interface. After power-up, the XRA1201 has internal 100K ohm pull-up resistors on each pin
XRA1202/1202P 8-BIT I2C/SMBUS GPIO EXPANDER WITH RESET
8-BIT I2C/SMBUS GPIO EXPANDER WITH RESET APRIL 2013 REV. 1.0.1 GENERAL DESCRIPTION The XRA1202/1202P is an 8-bit GPIO expander with an I 2 C/SMBus interface. After power-up, the XRA1202 has internal 100K
SP5301. Universal Serial Bus Transceiver
SP5301 Universal Serial Bus Transceiver Utilizes digital inputs and outputs to transmit and receive USB cable data Supports 12Mbps "Full Speed" and 1.5Mbps "Low Speed" serial data transmission Compatible
+5V Powered Multi-Channel RS-232 Drivers/Receivers
SP238A 5V Powered Multi-Channel RS-232 Drivers/Receivers Operates from a Single 5V Power Supply Meets All RS-232D and V.28 Specifications ±30V Receiver Input Levels Low Power CMOS Operation Operates with
XR32220 Evaluation Board User s Manual
XR32220 Evaluation Board User s Manual Introduction Exar s XR32220 EVB evaluation board provides a platform on which to examine the features and performance of the XR32220 2-Driver/2-Receiver RS-232 serial
XR76117/21. PowerBlox 15A and 20A Synchronous Step Down COT Regulator GENERAL DESCRIPTION EVALUATION BOARD MANUAL FEATURES
XR76117/21 November 2016 GENERAL DESCRIPTION The XR76117 and XR76121 are synchronous step-down regulators combining the controller, drivers, bootstrap diode and MOSFETs in a single package for point-of-load
XRD8775 CMOS 8-Bit High Speed Analog-to-Digital Converter
CMOS 8-Bit High Speed Analog-to-Digital Converter April 2002-4 FEATURES 8-Bit Resolution Up to 20MHz Sampling Rate Internal S/H Function Single Supply: 5V V IN DC Range: 0V to V DD V REF DC Range: 1V to
GENERAL DESCRIPTION APPLICATIONS FEATURES TYPICAL APPLICATION DIAGRAM
August 2009 Rev. 2.0.0 GENERAL DESCRIPTION The SP6686 is a current-regulated charge pump ideal for powering high brightness LEDs for camera flash applications. The charge pump can be set to regulate two
December 2009 Rev FEATURES. C2 0.47uF. C1 0.47uF C2P C1P C2N 17. COUT 10uF VOUT U1 U1 XRP6840 CAP 14. C3 CAPxx GND 13 NC 12 PGND FLASH LED3
December 2009 Rev. 1.0.0 GENERAL DESCRIPTION The XRP6840 is a controlled-current dual-cell supercapacitor charger and high power LED driver. Operating from a standard lithium-ion battery, the XRP6840 provides
XRD87L85 Low-Voltage CMOS 8-Bit High-Speed Analog-to-Digital Converter
Low-Voltage CMOS 8-Bit High-Speed Analog-to-Digital Converter April 2002-1 FEATURES 8-Bit Resolution Up to 10 MHz Sampling Rate Internal S/H Function Single Supply: 3.3V VIN DC Range: 0V to V DD VREF DC
High Current Power Switch
SP619 High Current Power Switch FEATURES Max RDS(ON).377 Ohms Overcurrent deactivation 800mA Max leakage current less than 2µA while deactivated Small 6 pin SOT-23 package Built-in Over-temperature Protection
ST78C34 GENERAL PURPOSE PARALLEL PRINTER PORT WITH 83 BYTE FIFO DESCRIPTION. PLCC Package FEATURES ORDERING INFORMATION
GENERAL PURPOSE PARALLEL PRINTER PORT WITH 83 BYTE FIFO DESCRIPTION The ST78C34 is a monolithic Bidirectional Parallel port designed to operate as a general purpose I/O port. It contains all the necessary
USB Port MTT Hub
USB 2.0 4-Port MTT Hub General Description The is a USB 2.0 4-port hub using multiple transaction translators (MTT) for highest possible bandwidth capability. The upstream USB interface has an integrated
AN10428 UART-SPI Gateway for Philips SPI slave bridges
UART-SPI Gateway for Philips SPI slave bridges Rev. 01 7 March 2006 Application note Document information Info Keywords Abstract Content UART-SPI Gateway, UART to SPI, RS-232 to SPI The UART-SPI Gateway
PCIe-400 USER S MANUAL
PCIe-400 USER S MANUAL 2017 May Edition Titan Electronics Inc. Web: www.titan.tw The computer programs provided with the hardware are supplied under a license. The software provided should be used only
Power Management and Interface Products for Cable, Satellite and IP STB/Home Gateway
Power Management and Interface Products for Cable, Satellite and IP STB/Home Gateway Power Conversion Step-Down Regulators LDOs DDR Termination System Controls Power Switches Supervisors Programmable Power
AN1204 Configuration of CANopen devices via LSS
AN1204 Configuration of CANopen devices via LSS This application note explains the procedure for changing node-id (address) and bittiming parameters (bit rate) of CANopen devices via LSS (Layer Setting
October 2012 Rev FEATURES
October 2012 Rev. 1.0.0 GENERAL DESCRIPTION The XRP7724 controller includes an I2C serial command interface for performing numerous common tasks. This document covers details on the command types and their
PCI Express 4-Port Industrial Serial I/O Cards
PCI Express 4-Port Industrial Serial I/O Cards The PCIe-400i and PCIe-400i-SI PCI Express 4-port industrial serial I/O cards are plug & play high-speed serial I/O expansion cards for the PCI Express bus.
HX2VL Development Kit Guide. Doc. # Rev. *A
HX2VL Development Kit Guide Doc. # 001-73960 Rev. *A Cypress Semiconductor 198 Champion Court San Jose, CA 95134-1709 Phone (USA): 800.858.1810 Phone (Intnl): 408.943.2600 http://www.cypress.com Copyrights
SP233A,SP310A and SP312A
SP233A,SP310A and SP312A Enhanced RS-232 Line Drivers/Receivers FEATURES Operates from a Single 5V Power Supply Meets all RS-232F and ITU V.28 Specifications Operates with 0.1μF Ceramic Capacitors No External
INTRODUCTION: DOWNLOADING & INSTALLATION:
INTRODUCTION: PowerArchitect TM is Exar s intuitive and easy-to-use software for developing power supplies with the XRP7724, XRP7720, XRP7725, XRP9711, and XRP9710 family programmable power management
January 2014 Rev FEATURES
January 2014 Rev. 1.2.0 GENERAL DESCRIPTION Some Exar Programmable Power products include an I 2 C serial command interface for performing numerous common tasks. This document covers details on the command
E IO-Link Transceiver Evaluation Kit PCB 2 (with external transistor)
E981.10 IO-Link evaluation Kit PCB 2 (with external transistor) AN 006 E981.10 IO-Link Transceiver Evaluation Kit PCB 2 (with external transistor) 1 What you get - E981.10 IO-Link Evaluation Kit PCB 2
PAC5523EVK1. Power Application Controllers. PAC5523EVK1 User s Guide. Copyright 2017 Active-Semi, Inc.
PAC5523EVK1 Power Application Controllers PAC5523EVK1 User s Guide www.active-semi.com Copyright 2017 Active-Semi, Inc. CONTENTS Contents...2 Overview...3 PAC5523EVK1 Resources...5 Pinout and Signal Connectivity...5
HX2VL Development Kit Guide. Doc. # Rev. **
HX2VL Development Kit Guide Doc. # 001-73960 Rev. ** Cypress Semiconductor 198 Champion Court San Jose, CA 95134-1709 Phone (USA): 800.858.1810 Phone (Intnl): 408.943.2600 http://www.cypress.com Copyrights
LAN9303 Evaluation Board User Manual
Copyright 2009 SMSC or its subsidiaries. All rights reserved. Circuit diagrams and other information relating to SMSC products are included as a means of illustrating typical applications. Consequently,
USB Port Hub. Description. Typical Application. USB Host. Upstream Phy XR Hub Controller MTT. Port Routing.
USB 2.0 7-Port Hub Description The XR22417 is a USB 2.0 7-port hub using Multiple Transaction Translators (MTT) for highest possible bandwidth capability. The upstream USB interface has an integrated USB
High Performance RS-232 Line Drivers/Receivers
SP202E,SP232E, SP233E, SP310E and SP312E High Performance RS-232 Line Drivers/Receivers FEATURES Operates from a Single +5V Power Supply Meets all RS-232D and ITU V.28 Specifications Operates with 0.1μF
Features. Applications
ALA ADAT Optical Encoder General Description The ALA OptoGen interface encodes four stereo pairs (8 channels) of digital audio and produces a single data stream suitable for transmission according to the
PCIEMODBOX232 RS232 to PCI Module Box Introduction
PCIEMODBOX232 RS232 to PCI Module Box Introduction This high performance PCI (or PCIe) RS232/422/485 Combo Expansion Module product includes an expansion module box, a PCI (or PCIe) Host Adapter and a
Application Note AN-225
Application Note AN-225 Installing and Testing a PCI / PCIe UART Serial Port Using a Custom MaxLinear Driver in Linux Introduction This Application Note covers how to load custom PCI/PCIe UART drivers,
AN4113 Application note
Application note Managing the Driver Enable signal for RS-485 and IO-Link communications with the STM32F05x USART Introduction RS-485 and IO-Link are half-duplex communication protocols that offer easy
Evaluation Board for CS8130
Features Evaluation Board for CS8130 ldesigned to conform to IrDA Physical Layer Specification linterfaces to PC Serial Port loperates from +2.7 V to 5.5 V Power Supply lincludes Evaluation Software Description
FEBFOD8012_RS485 Evaluation Board. Bi-Directional Logic Gate Optocoupler Provides Proven and Reliable Isolation to the RS485 Interface
User Guide for FEBFOD8012_RS485 Evaluation Board Bi-Directional Logic Gate Optocoupler Provides Proven and Reliable Isolation to the RS485 Interface Featured Fairchild Product: FOD8012 Direct questions
EZ-USB FX3 Development Kit Guide
CYUSB3KIT-001 EZ-USB FX3 Development Kit Guide Doc. #: 001-70237 Rev. *A Cypress Semiconductor 198 Champion Court San Jose, CA 95134-1709 Phone (USA): 800.858.1810 Phone (Intnl): 408.943.2600 http://www.cypress.com
E Mux Demonstration Board AN 0141 Jul 10, 2015
1 What you get: 1. One or more demonstration boards 2. Board description (this document) 3. USB Stick or CD - with driver for elmos LIN converter - GUI - flash and auto-addressing software 2 What you need
Ethernet1 Xplained Pro
Ethernet1 Xplained Pro Part Number: ATETHERNET1-XPRO The Atmel Ethernet1 Xplained Pro is an extension board to the Atmel Xplained Pro evaluation platform. The board enables the user to experiment with
User Manual. CANopenIA-M0. Starter Kit
User Manual CANopenIA-M0 Starter Kit Edition 8 March 2017 Page 2 of 21 The information given in this document was compiled and checked carefully. Nevertheless ESS assumes no liability for any mistakes.
Is Now A Part Of. Visit for more information about MaxLinear Inc.
Is Now A Part Of Visit www.maxlinear.com for more information about MaxLinear Inc. SP31E Intelligent 3.0V to 5.5V RS-3 Transceiver FEATURES Meets true EIA/TIA-3-F Standards from a 3.0V to 5.5V power supply
LIN bus board datasheet EB
LIN bus board datasheet EB027-00-1 Contents 1. About this document... 2 2. General information... 3 3. Board layout... 4 4. Testing this product... 5 5. Circuit description... 7 Appendix 1 Circuit diagram
Preliminary. PACKAGE - 28-pin MLP (5mm X 5mm) Example Circuit Diagram CP V. 48MHz Oscillator. USB Function Controller 512B EEPROM
Preliminary Single-Chip USB to UART Bridge SINGLE-CHIP USB to UART DATA TRANSFER - Integrated USB Transceiver; No External Resistors Required - Integrated Clock; No External Crystal Required - Integrated
EX-9686U/A-L(A9) Hardware User Manual
EX-9686U/A-L(A9) Hardware User Manual Release Notes Version Release Date Notes 1.00 November, 2013 Initial Release 2.00 January, 2014 The 2 nd release Disclaimer This documentation is provided for use
Evaluation Board for CS5351
Features Evaluation Board for CS5351 Demonstrates recommended layout and grounding arrangements CS8406 generates S/PDIF, and EIAJ-340 compatible digital audio Requires only an analog signal source and
INTEGRATED CIRCUITS ABSTRACT
INTEGRATED CIRCUITS ABSTRACT Brief set-up routine for using the automatic turn-around feature for transceiver control when using the RS-485 (sometimes called 9-bit or multi-drop mode) protocol. An interrupt
RE866 Interface User Guide
RE866 Interface User Guide 1VV0301387 Rev.0 6/16/2017 [04.2016] Mod. 0809 2016-08 Rev.7 SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE NOTICE While reasonable efforts have been made to assure the
USB2I 2 C Programming Kit Quick-Start User s Guide
Revision A USB2I 2 C Programming Kit Quick-Start User s Guide General Description The SMX3203 USB programming system is used for device prototype development. The SMX3203 system consists of a programming
STARTUP GUIDE. SP en-us ENGLISH
Anybus PoEInjector 100 240VAC STARTUP GUIDE ENGLISH Important User Information Liability Every care has been taken in the preparation of this document. Please inform HMS Industrial Networks AB of any inaccuracies
DATASHEET 4D SYSTEMS TURNING TECHNOLOGY INTO ART. USB to Serial UART Bridge Converter. Document Date: 5 th September 2012 Document Revision: 1.
TURNING TECHNOLOGY INTO ART DATASHEET USB to Serial UART Bridge Converter µusb-mb5 Document Date: 5 th September 2012 Document Revision: 1.0 Uncontrolled Copy when printed or downloaded. Please refer to
Evaluation Board for CS5361
Evaluation Board for CS5361 Features Demonstrates recommended layout and grounding arrangements CS8406 generates S/PDIF, and EIAJ-340 compatible digital audio Requires only an analog signal source and
IS31AP2145A Class-D Audio Amplifier Evaluation Board Guide
Description The IS31AP2145A demo board is a fully assembled and tested PCB that uses the IS31AP2145A Class-D audio amplifier to drive speakers with 4Ω load or larger. The device is designed for battery
M3H Group(1) Application Note. I 2 C Interface (I2C-B) MASTER/SLAVE
M3H Group(1) I 2 C Interface (I2C-B) MASTER/SLAVE Outlines This application note is a reference material for developing products using the Master/Slave function in I2C interface (I2C) functions of M3H
HYDRA-X23/X23S. Power Application Controllers. PAC HYDRA-X User s Guide. Copyright 2014 Active-Semi, Inc.
HYDRA-X23/X23S Power Application Controllers PAC5223 - HYDRA-X User s Guide www.active-semi.com Copyright 2014 Active-Semi, Inc. CONTENTS Contents...2 Overview...3 HYDRA-X23/X23S Body Resources...5 Header
SP3222EU/SP3232EU. 3.3V, 1000 kbps RS-232 Transceivers
SP3EU/SP33EU 3.3V, 1000 kbps RS-3 Transceivers FEATURES Meets true EIA/TIA-3-F Standards from a 3.0V to 5.5V power supply Minimum 1000kbps Data Rate 1µA Low Power Shutdown with Receivers active (SP3EU)
ET-UARTSWD Users Guide
User s Guide ET-UARTSWD Users Guide Power Application Controller s www.active-semi.com Copyright 2018 Active-Semi, Inc. CONTENTS Contents...2 Overview...3 1. ET-UARTSWD Resources...6 1.1 Provided Connectors...6
Please visit SMSC's website at for the latest updated documentation.
AN 10.13 Migrating from the LAN83C180 10/100 PHY to the 10/100 PHY 1 Introduction 1.1 Overview This application note discusses how to migrate from an existing design using the SMSC LAN83C180 PHY to SMSC's
Generic Mapping Procedure. White Paper
White Paper Introduction Recent enhancements to the OTN address the growing need to provide a transport layer for packet and data oriented networks. These enhancements have included defi nition of new
PCI Express 16-Port Serial I/O Cards
PCI Express 16-Port Serial I/O Cards The PCIe-1600 PCI Express 16-port serial I/O card is a plug & play high-speed serial I/O expansion card for PCI Express bus. Connecting to a PCI Express bus on your
This Application Note demonstrates an SPI-LIN slave bridge using a PSoC device. Demonstration projects are included.
Communication - SPI-LIN Slave Bridge Application Note Abstract AN0 Author: Valeriy Kyrynyuk Associated Project: Yes Associated Part Family: CY8C7 GET FREE SAMPLES HERE Software Version: PSoC Designer.
TPMC Channel Serial Interface RS232/RS422. Version 1.0. User Manual. Issue August 2014
The Embedded I/O Company TPMC461 8 Channel Serial Interface RS232/RS422 Version 1.0 User Manual Issue 1.0.6 August 2014 TEWS TECHNOLOGIES GmbH Am Bahnhof 7 25469 Halstenbek, Germany www.tews.com Phone:
This manual provides information for the final user application developer on how to use SPC57S-Discovery microcontroller evaluation board.
User manual SPC570S-DISP: Discovery+ Evaluation Board Introduction This manual provides information for the final user application developer on how to use SPC57S-Discovery microcontroller evaluation board.
Figure 1. CP2108 USB-to-Quad UART Bridge Controller Evaluation Board
CP2108 EVALUATION KIT USER S GUIDE 1. Introduction The CP2108 is a highly integrated USB-to-Quad-UART Bridge Controller providing a simple solution for updating RS-232/RS-485 designs to USB using a minimum
WiFi-110E WiFi-110E Datasheet
WiFi-110E Datasheet REV 2.0 Page 1 of 9 Aug. 1, 2011 CONTENTS 1. Overview... 4 2. Features... 5 3. Specification... 6 4. Hardware Description... 7 4.1 Terminal Definition... 7 5. Mechanical Dimension...
STEVAL-PCC010V1. ST802RT1A Ethernet PHY demonstration board with STM32F107 controller add-on board. Features. Description
ST802RT1A Ethernet PHY demonstration board with STM32F107 controller add-on board Data brief Features ST802RT1A Ethernet PHY demonstration board: ST802RT1A fast Ethernet physical layer transceiver On-board
MODEL P104-COM232-8 USER MANUAL
10623 Roselle Street, San Diego, CA 92121 (858) 550-9559 Fax (858) 550-7322 contactus@accesio.com www.accesio.com MODEL P104-COM232-8 USER MANUAL FILE: mp104-com232-8.a1g Notice The information in this
SPI Overview and Operation
White Paper Abstract Communications between semiconductor devices is very common. Many different protocols are already defined in addition to the infinite ways to communicate with a proprietary protocol.
E Demonstration Board AN 0178 Dec 15, 2016
E.0 Demonstration Board AN 0 Dec, 0 E.0 Power LIN.X Stepper with Stall Detection What you get. Demoboard E.0 What you need in addition. V Power Supply, capable of providing the motor current. Bipolar stepper
IS31LT3918 T8 Lighting Evaluation Board Guide
Description Quick Start The IS31LT3918 LED driver IC is a peak current detection buck converter which operates in constant off time mode. It operates over a very wide input voltage supply range of 6VDC
USB Debug Adapter. Power USB DEBUG ADAPTER. Silicon Laboratories. Stop. Run. Figure 1. Hardware Setup using a USB Debug Adapter
C8051F35X-DK DEVELOPMENT KIT USER S GUIDE 1. Kit Contents The C8051F35x-DK Development Kit contains the following items: C8051F350 Target Board C8051Fxxx Development Kit Quick-Start Guide AC to DC Power
HYDRA-X10. Power Application Controllers TM. PAC HYDRA-X User s Guide. Copyright 2014 Active-Semi, Inc.
HYDRA-X10 Power Application Controllers TM PAC5210 - HYDRA-X User s Guide www.active-semi.com Copyright 2014 Active-Semi, Inc. CONTENTS Contents...2 Overview...3 HYDRA-X10 Body Resources...5 Header Descriptions...5
Data Sheet Rev DALLIS Serial Data
Lawo AG, Germany Phone: +9 00-0 Web: www.lawo.de Data Sheet Rev. 00-0-0 DALLIS Serial Data Port serial multi-format data converter 9/ Serial Data bidirectional data Ports, data rates up to 00 bps Supports
RN-174. WiSnap M2 Super Module. Features. Description. Applications. ~ page 1 ~ rn-174-ds v1.1 6/1/2011
WiSnap M2 Super Module Features Development board containing the RN-171 module, status LEDs, power regulator Supports chip antenna (RN-174-C), PCB Trace antenna (RN-174-P), wire antenna (RN- 174-W) and
BIG8051. Development system. User manual
BIG8051 User manual All s development systems represent irreplaceable tools for programming and developing microcontroller-based devices. Carefully chosen components and the use of machines of the last
AN1203 Automatic start of CANopen slave devices
AN1203 Automatic start of CANopen slave devices This application note explains the procedure to start the cyclic transmission of Process Data Objects (PDOs) automatically after power on. Contents 1 Introduction.........................................
EMX-ESG User Manual. EMX I/O Module with 2 Gigabit Ethernet, 6 Serial Ports, and 14 GPIO
EMX-ESG User Manual EMX I/O Module with 2 Gigabit Ethernet, 6 Serial Ports, and 14 GPIO Revision Date Comment A.0 2/17/2013 Initial Release FOR TECHNICAL SUPPORT PLEASE CONTACT: Copyright 2013 Diamond
MODEL USB-COM-2SM USER MANUAL
C (C C MODEL USB-COM-2SM USER MANUAL FILE: MUSB-COM-2SM.A1a Notice The information in this document is provided for reference only. Portwell does not assume any liability arising out of the application
Chipset Evaluation and Development Loadboard Version 2
IA MSC-UGLB2 Chipset Evaluation and Development Loadboard Version 2 User Guide Revision 1.0r IA MSC-UGLB2 rev 1.0r 0907 2007, Silicon Laboratories, Inc. Silicon Labs, Inc. 400 West Cesar Chavez Austin,
EMX-ESG User Manual. EMX I/O Module with 2 Gigabit Ethernet, 6 Serial Ports, and 14 GPIO
EMX-ESG User Manual EMX I/O Module with 2 Gigabit Ethernet, 6 Serial Ports, and 14 GPIO Revision Date Comment A.0 2/17/2013 Initial Release A.1 3/5/15 Jumper information enhanced FOR TECHNICAL SUPPORT
XR17V358 HIGH PERFORMANCE OCTAL PCI EXPRESS UART
HIGH PERFORMANCE OCTAL PCI EXPRESS UART APRIL 2011 REV. 1.0.3 GENERAL DESCRIPTION The XR17V358 1 (V358) is a single chip 8-channel PCI Express (PCIe) UART (Universal Asynchronous Receiver and Transmitter),
DEMO9S08SH32/SG32 Demonstration Board for Freescale MC9S08SH32/SG32
DOC-0421-010, REV A DEMO9S08SH32/SG32 Demonstration Board for Freescale MC9S08SH32/SG32 Axiom Manufacturing 2813 Industrial Lane Garland, TX 75041 Email: Sales@axman.com Web: http://www.axman.com CONTENTS
Tempo Semiconductor, Inc. TSDP18x Evaluation Board User Guide Rev 0.1 (April 27, 2018)
Tempo Semiconductor, Inc. TSDP18x Evaluation Board User Guide Rev 0.1 (April 27, 2018) TSDP18x Supported Modes Valid PCM Word Slots in TDM Mode SCLK to LRCLK Ratio Word Length 512 384 256 192 128 96 64
TIDA Test Report
Test Report January 2015 TIDA-00334 Test Report Bill Johns BMS/WLPC Abstract TI design TIDA-00334 wireless power supply transmitter is an application of the bq500212a IC in a small form factor design targeted
KIT34901EFEVB Evaluation Board
Freescale Semiconductor, Inc. User s Guide Document Number: KT34901UG Rev. 1.0, 2/2014 KIT34901EFEVB Evaluation Board Featuring the MC34901 High Speed CAN Transceiver Contents Figure 1. KIT34901EFEVB Evaluation
USB Debug Adapter. Power USB DEBUG ADAPTER. Silicon Laboratories. Stop. Run. Figure 1. Hardware Setup Using a USB Debug Adapter
C8051F33X DEVELOPMENT KIT USER S GUIDE 1. Kit Contents The C8051F33x Development Kit contains the following items: C8051F330 Target Board C8051Fxxx Development Kit Quick-Start Guide AC to DC Power Adapter
User Guide M.2 Development Kit (DVK-SU C) Version 1.0
A M.2 Development Kit (DVK-SU60-2230C) Version 1.0 REVISION HISTORY Version Date Notes Approver 1.0 29 July 2017 Initial Release Jay White 2 CONTENTS 1. Overview...4 1.1 Introduction...4 1.2 Package Contents...4
For the LAN91C111 TQFP package, the Vdd and AVdd pins are located as follows: Pin #1, #11, #16, #33, #44, #62, #77, #98, #110, #120.
AN 11.2 1 Purpose Current Measurements and Measurement Procedures for the LAN91C111 and LAN91C111 Evaluation Board This application note provides measurements of the current (ICC) consumed by the LAN91C111
DEMO9S08SH8/SG8 Demonstration Board for Freescale MC9S08SH8/SG8
DOC-0398-010, REV A DEMO9S08SH8/SG8 Demonstration Board for Freescale MC9S08SH8/SG8 Axiom Manufacturing 2813 Industrial Lane Garland, TX 75041 Email: Sales@axman.com Web: http://www.axman.com CONTENTS