Advantech Multiprog Deploying a project on KW

Transcription

1 Advantech Multiprog Deploying a project on KW Jeffrey Wang FAE 2006/2

2 Deploying a Project KW series Introduction Hardware Configuration Mutliprog I/O configuration Compiling and Downloading

3 Goals of the lesson Familiarize with KW I/O Configuration

4 ADAM-5510KW Series ADAM-5510KW 4-slot SoftLogic Controller ADAM-5510EKW 8-slot SoftLogic Controller w/o Ethernet ADAM-5510EKW/TP 8-slot Ethernet SoftLogic Controller Ethernet-enabled 4-Slot 8-Slot

5 KW - series Specification CPU: OS: Boot ROM-DOS Memory: Program,70KB(150KB for 5510KW/5510EKW) KW Source File 512KB SRAM: 640 KB Battery backup: ADAM-5510KW and ADAM- 5510EKW:32 KB (16 KB for Modbus, 16 KB for KW retain data) ADAM-5510EKW/TP:11 KB (4 KB for Modbus, 7KB for KW retain data) 5000 Series Modules

6 ADAM5510 KW COM1: RS-232, DB-9 connector COM2: RS-485, Terminal Block COM3 :Debug/Programming port (for system maintenance only), RS-232 interface, DB-9 connector COM4: RS-232/485 selectable, DB-9 connector

7 ADAM-5510 EKW, EKW/TP COM1: RS-232/485 selectable, DB-9 connector COM2: RS-485, Terminal Block COM3 :Debug/Programming port (for system maintenance only), RS-232 interface, DB-9 connector COM4: RS-232/485 selectable, DB-9 connector

8 KW-series DIP Switch DIP 1-5: Device ID setting DIP 6: COM1, COM2 switch DIP 7,8: Baud Rate Setting Tip: All DIP Switch off, KW will be in debug mode.

9 KW-series DIP Switch ID = 0 reserved by system configuration.

10 Host Connecting to KW Using COM1/RS-232 RS-232 Null Modem Cable RS-232/COM1 SW6 OFF COM Selection COM1/RS- 232 Mode Selection / Baud Rate Multiprog Protocol / bps

11 Host Connect to KW Using COM2/RS-485 SW6 ON COM Selection COM2/RS-485 Mode Selection / Baud Rate Multiprog Protocol / bps

12 Mutliprog I/O configuration Open the sample project (LD) Right click Rescores and select Settings Select COM port( your PC) DLL for TCP/IP, Click DLL and Input IP Address

13 Mutliprog I/O configuration Click Data area button to setup Data Area Input these values Non retain End user /Start system End System Retain End user / Start system End System

14 Mutliprog I/O configuration Double click IO_Configuration IO_Configuration Dialogbox Select INTPUT tab Click Properties or double click the selection.

15 Mutliprog I/O configuration Change User defined Input to Advantech ADAM5510KW Click Driver Parameter Logical address Length will be recalculated by the Driver Parameter Or Input by yourself

16 Mutliprog I/O configuration Select Slot 0 and select ADAM5051 If select AI module, select Advance button to setup module type

17 Mutliprog I/O configuration Although the length of Logical address will be recalculated. Data length

18 Mutliprog I/O configuration Select COM port date format Network setup (EKW/TP) Download the project. Reset the EKW/TP. When Power light is on, Run and COMM lights are off, reset the EKW/TP again. The EKW/TP IP will be changed.

19 Mutliprog I/O configuration Select OUTPUT Tab Select Properties Change the Board I/O Module Select Slot 1 and select ADAM-5056 Check the Logical address length Click OK

20 Compiling the example- Making' the project Click on the 'Make' icon in the toolbar: Errors and warnings detected during compilation double clicking on an error/warning will open the worksheet Fix all errors and re-compile the project

21 Downloading the project to the I/O simulation Click on the 'Project Control Dialog' icon to open the resource control dialog Press the 'Download' button. Select Include Bootproject and click Download button.

22 Downloading the project to the I/O simulation Click the Cold' icon to execute a cold start Click the Stop icon to stop Click the Download icon to Reset.

23 FAQ about I/O Configuration Can I decide the number of address that I want, or there are fixed address? You don t decide the internal memory address. Mulitprog and KW will arrange the memory location automatically. If for example I have 10 modules and number1 is 8 DI and number 10 is 8AI how can I address them?( first 8 modules are in the master ADAM while the last 2 are in the slave ADAM) Is correct to write: %IX 0.0(for first input of DI) and %IB10.0 (for first input of AI)? Not exactly true. Actually, you can assign the address what you want.

24 FAQ about I/O Configuration Which is the retain Area? From. To Select the Retain function. Variable or object will be kept in retain memory. Size of retain memory ADAM-5510KW and ADAM-5510EKW: 32 KB (16 KB for Modbus, 16 KB for KW retain data) ADAM-5510EKW/TP: 11 KB (4 KB for Modbus, 7KB for KW retain data)

25 Appendix Another way to setup the IP of EKW/TP

26 Configuring EKW/TP IP Installed ADAM-5510 series utility Launch ADAM-5510 series utility Click Launch Terminal Connecting EWK/TP COM3

27 Configuring EKW/TP IP address Short the INIT* pin to GND pin and reset KW.

28 Configuring EKW/TP IP address Click Refresh button Click Network Configuration button

29 Configuring EKW/TP IP address input IP address Click Obtain DNS address automatically Click Update button in IP/DHCP Exit this window Remove the connection between INIT* and GND Reset KW

30 Configuring EKW/TP IP address Open the sample_6k.zwt Right click Resource and select setting Click DLL Input Parameter : KW IP address

31 QUIZ