BLUE 3 INSTALLATION GUIDE

Size: px

Start display at page:

Download "BLUE 3 INSTALLATION GUIDE"

Barry Donald Oliver
5 years ago
Views:

1 BLUE 3 INSTALLATION GUIDE CATCH Power BLUE 3 Installation manual - Page 1

IMPORTANT This product must be installed by a licensed electrician. This product must be installed according to the AS3000 Australian Wiring Standards.

2 IMPORTANT This product must be installed by a licensed electrician. This product must be installed according to the AS3000 Australian Wiring Standards. DANGER Danger to life due to high voltage AC Always ensure all electricity sources are appropriately isolated when installing this piece of equipment. Inside the package 1 x CATCH Communicator 1 x CATCH Diverter 1 x AC Power cord 1 x CAT5 network cable 6 x Current Transformers Catch Power BLUE 3 Installation manual - Page 2

3 Installation Overview STEP 1: Register the device at Only our registered installer partners can register the device. Once registered, an will be sent to the device owner with login details for their CATCH unit. STEP 2: Install the CATCH Communicator next to the internet router STEP 3: Install the CATCH Diverter inside the meter box Catch Power BLUE 3 Installation manual - Page 3

4 CATCH COMMUNICATOR Installation The Communicator must be plugged directly into a power socket. Do not use power boards of any type. The Communicator can be plugged into any of the 3 phases. Use the supplied ethernet cable to plug the communicator into a spare ethernet port on the premises router. The network must have a DHCP service running for the communicator to operate on the network. Understanding the LED s - Internet Catch Power BLUE 3 Installation manual - Page 4

5 Understanding the LED s - Communicator / Diverter The Communicator and Diverter talk using the power circuit. Catch Power BLUE 3 Installation manual - Page 5

CATCH DIVERTER Installation IMPORTANT: Maximum load allowed to be connected to HW terminal is 7.2kW. Cable sizing must be chosen based on the AS3000 wiring standard.

6 CATCH DIVERTER Installation IMPORTANT: Maximum load allowed to be connected to HW terminal is 7.2kW. Cable sizing must be chosen based on the AS3000 wiring standard. The Diverter must be protected from weather and direct contact. The recommended installation location in inside the meter box, behind the metering board. The maximum load that can be connected to the Diverter is 7.2kW, however the maximum power delivered to the load is 5kW. IMPORTANT Catch Power BLUE 3 Installation manual - Page 6

7 BEFORE YOU BEGIN: The arrows next to the CT s in the wiring diagram represent the arrows on the inside of the CT s. Matching the CT s to the correct phase is critically important special care must be taken to ensure this happens. NEVER disconnect CT s from diverter while they are wrapped around a current carrying conductor. If Off Peak is not available leave the Off Peak connection empty. Multiple wires can be put through the Load/Solar CT, as long as all currents are in the same direction. Some electrical jurisdictions do not allow switches in the Off Peak circuit, if this is your case then do not connect the off peak circuit. Catch Power BLUE 3 Installation manual - Page 7

8 CONNECTING THE POWER CABLES PHASE R PHASE T PHASE S OFF PEAK HOT WATER NEUTRAL EARTH Active Conductors Ensure cables are sized for a 7.2kW load Ensure all terminal block screws are screwed in tight, even the ones that are not used. Phase sequence is not important, you can arbitrarily choose which phase goes to which Phase connection. Off Peak can come from any of the 3 phases. Catch Power BLUE 3 Installation manual - Page 8

9 CONNECTING THE CURRENT TRANSFORMERS It is vitally important the CT s are connected to the correct Phase. IMPORTANT Example: If the BLUE phase is connected to the PHASE S terminal block then the S Mains and S-Load ct s must be connected to the BLUE phase. The instructions below refer to the Phase-S ct s; however the same holds true for Phase-R and Phase-T. S-Mains Catch Power BLUE 3 Installation manual - Page 8

10 S-Load This CT can be placed on ALL loads on Phase-S, or it can be placed on the Phase-S solar wire. CT placed around ALL loads OR Catch Power BLUE 3 Installation manual - Page 10

11 CT placed around Solar Catch Power BLUE 3 Installation manual - Page 11

12 WIRING DIAGRAM GRID L1 L2 L3 N NEUTRAL BLOCK OFF PEAK METER ELECTRICITY METER S-Mains R-Mains T-Mains PHASE S OFF PEAK HOT WATER NEUTRAL EARTH OFF PEAK ISOLATOR 32A Max CATCH CIRCUIT BREAKER MAIN SWITCH PHASE R PHASE T 32A Max HW 32A Max S-Load T-Load R-Load SOLAR SUPPLY MAIN SWITCH OR R-Load T-Load S-Load HOUSE LOADS INVERTER HOT WATER Catch Power BLUE 3 Installation manual - Page 12

sonnen Installation Practical

sonnen Installation Practical sonnen Components sonnenbatterie eco 8.0 Single Phase System Components 4 sonnenbatterie eco 8.0 Single Phase System Components 5 sonnenbatterie eco 8.0 Single Phase System