Agilent Medalist i p Software Release

Transcription

1 08.20p Software Release Release Notes The 08.20p software release is a complete installation that includes enhancements and improvements to software stability. In this release, we have enabled High Voltage Zener testing of up to 60V with the ASRU Revision N card. In addition, we have introduced a new power supply model, N5747A, for supporting the high power features that are available on the ASRU Revision N card and Utility pin card. If you are upgrading from or software, then there is no need for any new testhead or software update licenses for this release. You will be able to access the same features with your existing basic testhead and feature licenses after the upgrade. Software enhancements and resolution of defects are included and listed in appendix A. A software compatibility matrix is given in appendix B. For more news and updates for the 08.20p software release, please visit Windows is a U.S. registered trademark of Microsoft Corporation. Intel and Pentium are U.S. registered trademarks of Intel Corporation. UNIX is a registered trademark of the Open Group. Technologies

2 What s New in 08.20p Software Release System Requirements The 08.20p software release provides the following features: High Voltage Zener Test The High Voltage Zener (HVZ) test uses special circuitry in the ASRU Revision N card to measure the forward bias voltage of the zener components. The zener diode voltage rating can be from 18V to 60V. New Power Supply N5747A A new N5747A power supply model is introduced with this software release. N5747A provides up to maximum of 750W of power and can only be used with the ASRU Revision N card (channels 3 and 4) and the Utility card (channels 7 and 8). ControlXTP Firmware for New NEC 2M x 8-bit SRAM The new ControlXTP firmware is by default enabled in this software release. The default file (xtp.xsvf with firmware version _1) works for both the new and old NEC SRAM ControlXTP Card. See Notes for New ControlXTP firmware. Additional Changes ControlXTP Card with New SDRAM Socket A newly designed ControlXTP Card (part number E ) with new SDRAM socket is available. See Notes for New ControlXTP Card. The minimum hardware and software requirements for the installation of the 08.20p software release are as follows: Table 1 Platform Hardware Other Minimum requirements Windows XP Professional SP2 or later Processor minimum Intel Pentium 4, 1.8 GHz or better Memory minimum 1 GB RAM (recommended 2 GB RAM) Disk space minimum 1 GB Minimum screen resolution 1024 x 768, 16-bit Anti-virus and firewall software are recommended to be installed 2 Release Notes

3 Software Licenses Important Notes The 08.20p software release requires a software update license. Users can still access the same features with their existing basic testhead and feature licenses. Notes for New ControlXTP Firmware The new ControlXTP firmware is by default enabled in the 08.20p software release. Users who upgrade their software to 08.20p will need to update all the ControlXTP firmware. If the firmware is not updated, users will get a diagnostics failure "Test 6, Subtest 0" with the error "FPGA firmware error". (See Figure 1.) Figure 1 Diagnostics failure message To update the ControlXTP firmware: 1 Boot up the testhead. 2 Launch the Diagnostics application. 3 Click Configuration and then Programmable Card Config. 4 Ensure that the Expected value is _1. Then click the Update All (F1) button to program all the ControlXTP cards on the testhead. (See Figure 2.) Release Notes 3

4 Click to update firmware on all ControlXTP cards Actual version: As found on ControlXTP cards Expected version: As found in xtp.xsvf file Figure 2 Diagnostics Configuration to update firmware Notes for New ControlXTP Card A newly designed ControlXTP card (part number E ) is available but there is no change in functionality for existing software revisions. Customers will receive this card starting November The new and existing ControlXTP cards (E and E respectively) can co- exist in the system with no changes to the firmware, which must be the _1 firmware. The new ControlXTP card is introduced for the following reasons: The current SDRAM socket is obsolete and has been replaced with a new DRAM socket J3601. The new SDRAM socket cannot be used on existing ControlXTP cards. The existing PCB has been replaced with a new PCB with layout changes to accommodate the new SDRAM socket. Table 2 Part numbers for new ControlXTP card Part number Description E ControlXTP card with new SDRAM socket; New E ControlXTP card with new SDRAM socket; Exchange 4 Release Notes

5 Appendix A Improvements Improvements in the 08.20p software release based on customer enhancement and defect requests are listed in Table 3. Table 3 Improvements based on customer requests Change Request Identification CR29820 CR30634 CR30635 CR30659 CR30669 CR30675 CR31033 CR32947 CR33687 CR33734 CR33769 CR33825 CR33828 CR33950 CR33965 CR33977 CR33988 CR34003 CR34042 CR34054 Description 07.00pc: Auto Optimizer did not log all the optimized tests p: Version tests could not be debugged for panel boards p: Software freezes when switching from version to base for panel boards p: Software enhancement customizable toolbar p: Software enhancement added a or b sensing bus p: Software enhancement version selected will be highlighted in pop-up window p: Enhancement Worst Probe Report linked to browser for probes highlighting p: Enhancement of mass edit for adding same guard nodes to multiple tests pc: IYET repeatedly logs the same failures pc: Missing some wires when IPG generated fixture file p: Enhanced display disabling for FPY and WPR pc: White space in config file not accepted in Debug Interface pc: IPG cannot write the shorts file for a large board with many shorts p: Cannot use two mux cards for dual well fixture p: IPG placed transfer pin at wrong bank for dual well share wiring fixture p: ERROR FDF238 when running fixture tooling pc: Internal Error 34/105/0 for Cover Extend Analysis in Access Consultant p: BT-BASIC cannot support relative directory p: UnMux software does not load board due to fractional tolerance written in scientific notation pc: Operator Interface gives internal error -11 when using 32 char string. Release Notes 5

6 Appendix B Compatibility Matrix Table 4 Compatibility matrix 3070 (UNIX ) Medalist 3070 (Windows) Medalist i5000 UnMux Mux Software Revision & below & below & below 08.20p & below 08.20p & below Operating System UNIX Windows 2000/ Windows XP Windows XP Windows XP Windows XP Controller Hardware HP B20000/ HP X2100*/IPC HP xw4200/ HP xw4400/ HP xw4400/ C36000 and (Advantech)/ HP xw4300 HP xw4600 HP xw4600 below HP xw4300 HP rp5700 HP rp5700 Remarks * HP X2100 is not supported on 05.40p and above Software Features Simplate Express Fixturing Analog In-circuit Test Analog Functional Test Timing Sets In-circuit Boundary-Scan InterconnectPlus Boundary-Scan PanelTest Throughput Multiplier TestJet VTEP v2.0 Powered! (VTEP, ivtep, (1) (1) (2) (2) (1) VTEP and ivtep only NPM and Cover-Extend) (2) NPM works on 07.10p or later CET works on 07.20p or later Cover-Extend Technology CET works on 07.20p or later Polarity Check Connect Check Powered Testing Software Revision B All High Accuracy Resources Fault Detective DriveThru Flash70 6 Release Notes

7 Table 4 Compatibility matrix Awaretest xi Not supported MagicTest Control XT Override Advanced Fixturing Silicon Nails Flash ISP Needs Control XTP PLD ISP Needs Control XTP Diagnose Relays System Calibration Medalist Interactive Pin Locator Automatic Analog Debug (AutoDebug) 3070 (UNIX ) Medalist 3070 (Windows) Medalist i5000 UnMux Mux Remarks Medalist AutoOptimizer Needs Control XTP Medalist Operator Interface Medalist Debug Interface ICT Browser Coverage Analyst Fixture Consultant * * * i5000/i3070 UnMux uses ICT Browser Board Consultant * * * i5000/i3070 UnMux uses TTM Development Software Test Consultant * * * i5000/i3070 UnMux uses TTM Development Software Medalist TTM Development Software * * * * 3070/i3070 Mux uses Board Consultant, Fixture Consultant and Test Consultant Pushbutton Debug Access Consultant Part Description Editor Device Test Library BT-Basic Test Language Release Notes 7

8 Table 4 Compatibility matrix Setup Test Editor Analog Test Language Vector Control Language Pattern Capture Format Digital In-circuit Test Integrated Digital In-circuit and Analog Functional Test Language 3070 (UNIX ) Medalist 3070 (Windows) Medalist i5000 UnMux Mux IPG-II Program Generator Multiple Board Versions Dual-Well Shared Wiring Short-wire Fixture Technology Board Test Grader Datalogging Pushbutton Q-STATS Remarks CAMCAD No longer supported. Advanced Probe Spacing * * Available only on (UNIX) Automatic 6 Wire Analog ICT Tests Automatic Digital Test Generation Safeguard ICT Analysis Quick Report ScanWorks * * Works only on or later System Configuration and Hardware Diagnostics Medalist Repair Tool RS232 Control IEEE 488 Instrumentation * * * * Not tested 8 Release Notes

9 Table 4 Compatibility matrix 3070 (UNIX ) Medalist 3070 (Windows) Medalist i5000 UnMux Mux Remarks Hardware Features ASRU Rev A * * Supported only on (UNIX) ASRU Rev B * * Supported only on (UNIX) ASRU Rev C ASRU Rev D ASRU Rev N * * * Works only with Control XTP and 08.00p or later Serial Test Card * * Supported only on (UNIX) Serial Test Plus card * * Supported only on (UNIX) Serial Test Pay Per use * * Supported only on (UNIX) ChannelPlus ChannelPlus Pay Per Use Control Card * * Supported only on (UNIX) ControlPlus Card * * Supported only on (UNIX) ControlXT * * ASRU Rev N not supported ControlXTP HybridPlus SD/DD Pay Per Use * * Supported only on HybridPlus DD Pay Per Use HybridPlus SD 6/12/20 MP/s * * Supported only on (UNIX) HybridPlus DD 6/12/20 MP/s HybridPlus 32 6/12/20MP/s End of support HybridPlus 32 Pay Per Use End of support HybridPlus 32 Value Series End of support Release Notes 9

10 Table 4 Compatibility matrix 3070 (UNIX ) Medalist 3070 (Windows) Medalist i5000 UnMux Mux Remarks HybridPlus 144 unmux AnalogPlus (SD) AnalogPlus (DD) AccessPlus (SD) Utility Card * * Works with 08.00p or later Guided Probe and Footswitch Bar Code Scanner (E3786A) Strip Printer Debug Ports (3) Functional Test Access Ports Performance Port DUT Power Supplies Vacuum Compressed Air Quick Connect Tap Power Supply Support Bay JOT Handler 10 Release Notes

11

12 Technologies, Inc Printed in USA 01/2011 E Technologies