MorphoAccess. Configuration Tool User Guide. MorphoAccess. Configuration Tool User Guide SSE Produced by Sagem Sécurité

Transcription

1 MorphoAccess Configuration Tool User Guide Produced by Sagem Sécurité Copyright 2010 Sagem Sécurité MorphoAccess SSE Configuration Tool User Guide May 2010

2 Table of Contents REVISION HISTORY 3 SCOPE OF THE DOCUMENT 4 INTRODUCTION 6 STARTING THE APPLICATION 7 CONNECTION 7 CONNECTION ISSUES NOTE 8 TERMINAL CONFIGURATION FILE GROUP BOX 10 INTRODUCTION 10 CONFIGURATION INTERFACE 10 CONFIGURATION ORGANIZATION 10 FILE SELECTION 10 OPERATIONS 12 CHANGING A PARAMETER 13 DISPLAYING OR SAVING A TERMINAL CONFIGURATION FILE 16 ADDITIONAL OPERATIONS GROUP BOX 18 INTRODUCTION 18 ADDITIONAL OPERATIONS 18 ADDITIONNAL OPERATIONS GROUP BOX 19 REBOOT TERMINAL 21 SUPPORT 23 CUSTOMER SERVICE 23 HOTLINE 23 2 Sagem Sécurité document. Reproduction and disclosure forbidden SSE

3 REVISION HISTORY Date Revision Description May Add MorphoAccess J Series SSE Sagem Sécurité document. Reproduction and disclosure forbidden 3

4 SCOPE OF THE DOCUMENT This guide relates to the use of MorphoAccess access control terminals: MorphoAccess 100 Series MorphoAccess J Series MorphoAccess 500 Series MorphoAccess 100 Series are made up of following list of products: Biometrics Contactless Smartcard Reader iclass TM MIFARE TM DESFire TM MA 100 MA 100 Series MA 110 MA 120 MA 120 D MorphoAccess J Series are made up of following list of products: Biometrics Contactless Smartcard Reader MIFARE TM DESFire TM MorphoAccess J Series MorphoAccess J-Bio MorphoAccess J-Dual 4 Sagem Sécurité document. Reproduction and disclosure forbidden SSE

5 MorphoAccess 500 Series is a generic appellation which gathers MorphoAccess terminals belonging to MA 500+ Series, OMA 500 Series and MA 500 Series. Corresponding list of products is depicted in the table below. Biometrics Contactless Smartcard Reader MIFARE TM DESFire TM Fake Finger Detection Outdoor MA 500+ Series MA 500+ MA 520+ D MA 521+ D OMA 520 D OMA 500 Series OMA 521 D OMA 520 OMA 521 MA 500 Series MA 500 MA 520 MA 521 SSE Sagem Sécurité document. Reproduction and disclosure forbidden 5

6 INTRODUCTION All MorphoAccess terminals (100 Series, J Series and 500 Series) can be fully administrated through TCP/IP. The terminal acts as a server allowing: changing some terminal parameters, displaying or saving a terminal configuration file, additional operations (only setting or getting the terminal date for the current version), rebooting (restart) the terminal. These operations require connecting the terminal on a network (TCP-IP). All these features will be performed by the Configuration Tool application and are described in this present document. 6 Sagem Sécurité document. Reproduction and disclosure forbidden SSE

7 STARTING THE APPLICATION Connection Launch the Configuration Tool.exe application. The MorphoAccess Connection dialog window is displayed. This step consists in connecting your terminal to a network and is required before performing any operation. The process is as follows: connect physically your terminal to a network, set the terminal IP address in the IP address field, (Default IP address from factory setting is : ), set the remote management TCP Port in the Port field, click on the Connect >> button. SSE Sagem Sécurité document. Reproduction and disclosure forbidden 7

8 If the process succeeds, the Configuration Tool main dialog window appears on your screen: You can now perform any operation described in this document. Connection issues note Take note of the remote management TCP Port if you change its value. In fact, there is no tool to reset this value, so if you do not remember the right value, you could not connect your terminal later. If the TCP port value is wrong, you obtain the following message: 8 Sagem Sécurité document. Reproduction and disclosure forbidden SSE

9 The set IP address must be the actual address of your terminal. If you have previously changed this address by this tool or by another one, you must enter this last address. If these conditions are not respected, the following message displays on your screen: A similar message also appears if your terminal is not connected on a network: In all these cases, the application is still active and you can retry to connect your terminal on a network. SSE Sagem Sécurité document. Reproduction and disclosure forbidden 9

10 TERMINAL CONFIGURATION FILE GROUP BOX Introduction Configuration interface Terminal parameters are stored in files. These configuration files can be retrieved and modified through TCP using ILV commands. For more information about configuration files and parameters please refer to MorphoAccess 100 Series User Guide, MorphoAccess J Series User Guide or MorphoAccess 500 Series User Guide. Configuration organization The terminal contains several files: app.cfg, adm.cfg, bio.cfg, net.cfg, fac.cfg, wifi.cfg, gui.cfg exe.cfg, sslprofile.cfg The app.cfg file contains the MACCESS application settings, adm.cfg contains administration parameters, bio.cfg the biometric sensor settings, net.cfg the Ethernet interface parameters, fac.cfg the factory settings, wifi.cfg the WI-FI interface parameters, gui.cfg some Man-Machine interface parameters, exe.cfg some startup parameters, and sslprofile.cfg the parameters for SSL features. Parameter path has the following structure: file_name/section/parameter. For example the relay activation is driven by the app/relay/enabled parameter. File selection Under the Terminal Configuration File group box, you can find a list box named File Type: 10 Sagem Sécurité document. Reproduction and disclosure forbidden SSE

11 SSE Sagem Sécurité document. Reproduction and disclosure forbidden 11

12 This list contains the corresponding names of the terminal configuration files: Application Administration Bio Network Operations bio.cfg, app.cfg, net.cfg. adm.cfg, The Terminal Configuration File group box allows performing some operations on the terminal configuration files: changing one or several terminal parameters, displaying or saving a terminal configuration file. 12 Sagem Sécurité document. Reproduction and disclosure forbidden SSE

13 Changing a parameter The process is as follows: Select a terminal configuration file in the File Type list box: For example, we choose the Application configuration file. Retrieve the configuration file by clicking on the Get File button. The different file sections will display on the left part of the application: SSE Sagem Sécurité document. Reproduction and disclosure forbidden 13

14 Select a specific parameter by clicking first on the + of the specific section and then clicking on the parameter: For example, we choose the identification parameter of the bio ctrl section. To change this parameter, double click on the parameter. The Write a value dialog window appears on your screen: Change the value of the parameter in the Update a value field and then click on the Update value button. For example, we set the identification parameter value to Sagem Sécurité document. Reproduction and disclosure forbidden SSE

15 If the process succeeds: the new value of the parameter displays in a field above the file sections, a file_name/section/parameter updated message displays under the file sections. If a value is erroneous, a message appears and the parameter is reset to the previous value: This previous value also displays in the field above the file sections. For some parameters (like network parameters) you need to reboot your terminal to apply the changes. SSE Sagem Sécurité document. Reproduction and disclosure forbidden 15

16 Displaying or saving a terminal configuration file The process is as follows: Select a terminal configuration file in the File Type list box: For example, we choose the Application configuration file. Display the terminal configuration file by clicking on the Export File button. The Export Configuration File dialog window displays: This dialog window displays the content of the selected terminal configuration file: under each section represented between [ and ] all its corresponding parameters with their values are displayed. 16 Sagem Sécurité document. Reproduction and disclosure forbidden SSE

17 You can also save the terminal configuration file in a file on your PC (USB Mass Storage flash drive, hard disk ). To save the file, click on the Save File button, then select the path where you want to save the file and finally click on the save button (the name of this button depends on your PC language) The file is saved as a binary file but it is composed of printed characters: in fact this file contains exactly the data displayed in the Export Configuration File dialog window. As a result, it can be opened as a text file later. Finally, click on the Done button to return to the main dialog window. SSE Sagem Sécurité document. Reproduction and disclosure forbidden 17

18 ADDITIONAL OPERATIONS GROUP BOX Introduction This group box allows performing: some additional operations on your terminal (only setting or getting terminal date for the current version), terminal reboot. Additional Operations First, under the Additional Operations group box, click on the More button. The following Additional Operations dialog window appears on your screen: 18 Sagem Sécurité document. Reproduction and disclosure forbidden SSE

19 Additionnal Operations group box This group box allows: getting the terminal date and hour, setting the terminal date and hour, synchronizing the terminal date and hour with the PC date and hour, getting detailed information about your terminal. Getting the terminal date and hour The process is as follows: click on the Get Date button, the actual terminal date and hour display on the respective fields. Setting the terminal date and hour The process is as follows: Set the terminal date in the date field calendar: SSE Sagem Sécurité document. Reproduction and disclosure forbidden 19

20 Set the terminal hour in the respective field: Click on the Set Date button. The terminal date and hour are set with these values. Synchronizing the terminal date and hour The process is as follows: click on the Synchronize Date button, the terminal date and hour are set with the PC date and hour. 20 Sagem Sécurité document. Reproduction and disclosure forbidden SSE

21 Getting detailed information about you terminal The process is as follows: click on the Get Version Extended button, the window is filled with information about the terminal, the sensor (usefull for licence upgrading), Contactless reader, and other things. NOTE: To return to the main dialog window, click on the Done button. Reboot terminal The process is as follows: Click on the Reboot Terminal button. The following message will appear on your screen: SSE Sagem Sécurité document. Reproduction and disclosure forbidden 21

22 Click on the yes button (the name of this button depends on your PC language). The reboot process starts. Under the file sections, a message Terminal reboot in progress Please wait a few seconds displays and a progress bar displays and grows while the process runs. When the reboot process is completed, the following message appears on your screen: Finally, the file sections and actual parameters are cleared. NOTE: It is also possible to reboot your terminal when you quit the application. The same first message displays and you can choose to reboot your terminal or not. 22 Sagem Sécurité document. Reproduction and disclosure forbidden SSE

23 SUPPORT Customer service Hotline Sagem Sécurité SAV Terminaux Biométriques Boulevard Lénine - BP Saint Etienne du Rouvray FRANCE Phone: Sagem Sécurité Support Terminaux Biométriques 18, Chaussée Jules César Osny FRANCE hotline.biometrics@t.my-technicalsupport.com Phone: Copyright 2010 Sagem Sécurité SSE Sagem Sécurité document. Reproduction and disclosure forbidden 23

24 Head office : Le Ponant de Paris 27, rue Leblanc PARIS CEDEX 15 - FRANCE