Single cycle MIPS data path without Forwarding, Control, or Hazard Unit
|
|
- Christina Douglas
- 5 years ago
- Views:
Transcription
1 Single cycle MIPS data path without Forwarding, Control, or Hazard Unit Figure 1: an Overview of a MIPS datapath without Control and Forwarding (Patterson & Hennessy, 2014, p. 287) A MIPS 1 single cycle data path is a hardware description for a MIPS based processor architecture this is one of the simplest data paths that can still operate. In order for your computer to properly execute a program it brakes the complex process up into smaller, easier to preform instructions. These instructions are then loaded into the memory of the IF 2 stage to later be decoded and executed. The MIPS datapath can be broken into 5 main stages IF, ID 3, EX 4, MEM 5, and WB 6. Each of the stages has to work with the next stage and execute a specific task in order to properly execute an instruction. In order to understand the datapath as a whole you must first understand the pieces that go inside it. One of the main components are the registers, they are fast 32x32 memory locations that take in a 5 bit value from 0-31 and temporarily stores a 32 bit value. However, if a register has more locations then the standard 32 it will take in a larger number of bits. 1 Millions of Instructions Per Second, it is a type of instruction set 2 IF stands for Instruction Fetch 3 ID stands for Instruction Decode 4 EX stands for Execution 5 MEM stands for Memory Access 6 WB stands for Write Back
2 Instruction Fetch The first stage is all about keeping track of where the processor is in the current program s instruction stack and feeding the next instruction through the datapath. Initially the IF stage starts out by pulling an address out of the PC 7. This address is 4 words 8 long and is usually represented as a hexadecimal value. Just like how a house address is used to mail a letter this address used to locate the current instruction. This address is then passed by wire signals to two locations inside the IF stage, the adding unit and the instruction memory register. The adding unit is used to advance the current address to the next address. This new PC value is wired to 2 locations one of which doesn t get used till the EX stage so we will not worry about it for now. The second one goes into a multiplexor 9 as one of the inputs. This Multiplexor decides what the new PC value will be based on the input bit that is derived from the control module in the ID stage. The last component in the IF stage is the Instruction memory register. The instruction memory register first finds the memory location that the address. Then once the memory location is known the register outputs the first instruction. Instruction Decode The first instruction is 32 bits when it is initially read from the register. However, once it gets into the ID stage the instruction is separated so it can be decoded. Instructions come in 3 different formats R-type 10, I-type 11, and J-type 12. Each instruction format starts out with a 6 bit op code, this op code is used to control what gets read, written, when to branch 13, and what alu 14 operation gets executed. This control unit is usually above the registers in the ID stage and will not be covered in this description. Other than the control unit the main components of the ID stage are the registers. They are made up the same as before however we place the two 32x32 registers in one component because in order to perform any calculations two values need to be accessed at the same time. The 5 bit address for both the memory locations are the instructions 16 th 25 th bits, and the first read location is stored in the 21 st 25 th bits. These memory values are then passed along to the EX stage for processing. The registers must also allow for information to be written to the registers. This is handled with the addition of a write register port and a write data port. The write register port specifies where the information will be stored and the write data port holds the information to be stored and is controlled by the control unit. The last component is the sign extend module which takes in the 0-15 th bits from the instruction and all that it does is copy the first bit till the instruction is 32 bits long again. 7 Program Counter register, note this register can be nx32 where n is any positive number 8 A word is 8 bits and takes up one memory locations within the PC 9 It selects one input value out of many based on a sector bit(s) and outputs that value 10 R format 32 bits long and as follows 6 bit opcode, 5 bit first register, 5 bit second register, 5 bit destination register, 5 bit shift amount, 6 bit Function; used for most operations. 11 I-format 32 bits long as follows 6bit opcode, 5 fit first register, 5 bit destination register, 16 bit constant or address; used for immediate and data transfer instructions 12 J-format 32 bits long as follows 6 bit opcode, 26 bit address; used for jumping to an address that is far away 13 This happens when loading an instruction that is not sequentially after the last one. 14 Arithmetic logic unit preforms addition, subtraction, multiplication, and more.
3 Execution This sign extended value is then multiplied by 4 because we are working with words and one word is 4 bytes. By using a base 2 counting system we can just shift the value over by 2 decimals to the left this is the same as multiplying by 4. This value then goes into an adding unit who s other input is the new PC value which comes from the IF stage. The adding unit adds the top 4 bits of the PC value and the 32 bit sign extended value to create a jump 15 from the current instruction to a different one. The sign extended value is also used as an input into a multiplexor that is just before the ALU. The multiplexor s other input comes from the second register s output from the ID stage and is controlled with a selector bit from the control unit. The ALU has 3 inputs and 2 outputs, of the inputs 1 is a control signal that tells the ALU what operation to execute and the 2 other inputs are the values that the operation will be performed on. The first value comes from the first register in the ID stage and the second from the multiplexor. The ALU s outputs are a zero wire 16 and the output of the operation. Memory access and Write Back The MEM stage consists of data memory and an and-gate. The and gate takes the zero wire that comes from the ALU in the previous stage and a control signal from the control unit in the ID stage that indicates if a branch should be taken. Then the output of this and-gate is used as the selector bit for the multiplexor in the IF stage. The Data memory is used for long term information storage and has 4 inputs and 1 output. Two of the inputs are control signals that tell the memory when to read and write. The last of the inputs are the address and write data ports. The address port is used to locate the memory location and the write data port contains the information that will be written into the memory location. The data memory only has one output and that is the information that is stored in the memory location. This value then goes into the WB stage, the WB stage consists of a single multiplexor whose inputs are the data from the data memory in the MEM stage, the ALU result from the EX stage, and a control signal from the control unit. This multiplexor s output is wired up to the write data port of the registers in the ID stage. Conclusion We start in the IF stage, the PC starts by outputting an address to the first instruction this value is then incremented by 4 17 and set as an input to the PC. The address that was output by the PC is then input to the instruction memory and used to find then output the first instruction. We are now in the ID stage, from this instruction we read two memory locations from the registers. At the same time we are also sign extending a different part of the same instruction, because depending on the opcode we may need this part of the instruction. The instruction is now decoded and moves into the EX stage. The sign extended value is then multiplied by 4, gets the first 4 bits of its new PC 18 opcode added to it. This value is then wired to the PC where a multiplexor controlled by a control unit will select what the next instruction should be. The ALU takes in the data read from the first register in the ID stage as one input. The second 15 A Jump is preformed when executing a loop, if, case, and more. 16 This wire is used for comparisons and calculating branch instructions 17 this increments the PC to the next sequential instruction 18 Which came from the IF stage
4 input is selected by a multiplexor whose inputs the sign are extended value before it is multiplied by 4 and the data from the second register in the ID stage. Depending on the opcode the multiplexor will select the correct input and the ALU will perform the correct operation sending the result to the MEM stage where it will be stored in memory or to the WB stage to be stored back in the registers for more operations.
5 Works Cited Patterson, D. A., & Hennessy, J. A. (2014). Computer Organization and Design: The Hardware/Software Interface (5th ed.). (T. Green, Ed.) Burlington, MA, United States of America: Morgan Kaufmann. Retrieved July 21, 2016
Chapter 4. Instruction Execution. Introduction. CPU Overview. Multiplexers. Chapter 4 The Processor 1. The Processor.
COMPUTER ORGANIZATION AND DESIGN The Hardware/Software Interface 5 th Edition COMPUTER ORGANIZATION AND DESIGN The Hardware/Software Interface 5 th Edition Chapter 4 The Processor The Processor - Introduction
More informationCOMPUTER ORGANIZATION AND DESIGN. 5 th Edition. The Hardware/Software Interface. Chapter 4. The Processor
COMPUTER ORGANIZATION AND DESIGN The Hardware/Software Interface 5 th Edition Chapter 4 The Processor COMPUTER ORGANIZATION AND DESIGN The Hardware/Software Interface 5 th Edition The Processor - Introduction
More informationCOMPUTER ORGANIZATION AND DESIGN. 5 th Edition. The Hardware/Software Interface. Chapter 4. The Processor
COMPUTER ORGANIZATION AND DESIGN The Hardware/Software Interface 5 th Edition Chapter 4 The Processor Introduction CPU performance factors Instruction count Determined by ISA and compiler CPI and Cycle
More informationSystems Architecture
Systems Architecture Lecture 15: A Simple Implementation of MIPS Jeremy R. Johnson Anatole D. Ruslanov William M. Mongan Some or all figures from Computer Organization and Design: The Hardware/Software
More informationECE260: Fundamentals of Computer Engineering
ECE260: Fundamentals of Computer Engineering Pipelined Datapath and Control James Moscola Dept. of Engineering & Computer Science York College of Pennsylvania ECE260: Fundamentals of Computer Engineering
More informationData paths for MIPS instructions
You are familiar with how MIPS programs step from one instruction to the next, and how branches can occur conditionally or unconditionally. We next examine the machine level representation of how MIPS
More informationLaboratory Single-Cycle MIPS CPU Design (3): 16-bits version One clock cycle per instruction
Laboratory 6 6. Single-Cycle MIPS CPU Design (3): 16-bits version One clock cycle per instruction 6.1. Objectives Study, design, implement and test Instruction Decode Unit for the 16-bit Single-Cycle MIPS
More informationLaboratory Single-Cycle MIPS CPU Design (4): 16-bits version One clock cycle per instruction
Laboratory 7 7. Single-Cycle MIPS CPU Design (4): 16-bits version One clock cycle per instruction 7.1. Objectives Study, design, implement and test Instruction Execute Unit for the 16-bit Single-Cycle
More informationChapter 4. The Processor
Chapter 4 The Processor Introduction CPU performance factors Instruction count Determined by ISA and compiler CPI and Cycle time Determined by CPU hardware 4.1 Introduction We will examine two MIPS implementations
More informationELEC 5200/6200 Computer Architecture and Design Spring 2017 Lecture 4: Datapath and Control
ELEC 52/62 Computer Architecture and Design Spring 217 Lecture 4: Datapath and Control Ujjwal Guin, Assistant Professor Department of Electrical and Computer Engineering Auburn University, Auburn, AL 36849
More informationMulti Cycle Implementation Scheme for 8 bit Microprocessor by VHDL
Multi Cycle Implementation Scheme for 8 bit Microprocessor by VHDL Sharmin Abdullah, Nusrat Sharmin, Nafisha Alam Department of Electrical & Electronic Engineering Ahsanullah University of Science & Technology
More informationProcessor: Multi- Cycle Datapath & Control
Processor: Multi- Cycle Datapath & Control (Based on text: David A. Patterson & John L. Hennessy, Computer Organization and Design: The Hardware/Software Interface, 3 rd Ed., Morgan Kaufmann, 27) COURSE
More informationEECE 417 Computer Systems Architecture
EECE 417 Computer Systems Architecture Department of Electrical and Computer Engineering Howard University Charles Kim Spring 2007 1 Computer Organization and Design (3 rd Ed) -The Hardware/Software Interface
More informationThe Processor. Z. Jerry Shi Department of Computer Science and Engineering University of Connecticut. CSE3666: Introduction to Computer Architecture
The Processor Z. Jerry Shi Department of Computer Science and Engineering University of Connecticut CSE3666: Introduction to Computer Architecture Introduction CPU performance factors Instruction count
More informationIntroduction. Datapath Basics
Introduction CPU performance factors - Instruction count; determined by ISA and compiler - CPI and Cycle time; determined by CPU hardware 1 We will examine a simplified MIPS implementation in this course
More informationProcessor (I) - datapath & control. Hwansoo Han
Processor (I) - datapath & control Hwansoo Han Introduction CPU performance factors Instruction count - Determined by ISA and compiler CPI and Cycle time - Determined by CPU hardware We will examine two
More informationChapter 4. The Processor
Chapter 4 The Processor Introduction CPU performance factors Instruction count Determined by ISA and compiler CPI and Cycle time Determined by CPU hardware We will examine two MIPS implementations A simplified
More informationECE260: Fundamentals of Computer Engineering
Datapath for a Simplified Processor James Moscola Dept. of Engineering & Computer Science York College of Pennsylvania Based on Computer Organization and Design, 5th Edition by Patterson & Hennessy Introduction
More informationCOMP2611: Computer Organization. The Pipelined Processor
COMP2611: Computer Organization The 1 2 Background 2 High-Performance Processors 3 Two techniques for designing high-performance processors by exploiting parallelism: Multiprocessing: parallelism among
More informationCS3350B Computer Architecture Winter 2015
CS3350B Computer Architecture Winter 2015 Lecture 5.5: Single-Cycle CPU Datapath Design Marc Moreno Maza www.csd.uwo.ca/courses/cs3350b [Adapted from lectures on Computer Organization and Design, Patterson
More informationChapter 4. The Processor. Instruction count Determined by ISA and compiler. We will examine two MIPS implementations
Chapter 4 The Processor Part I Introduction CPU performance factors Instruction count Determined by ISA and compiler CPI and Cycle time Determined by CPU hardware We will examine two MIPS implementations
More informationCOMPUTER ORGANIZATION AND DESIGN. The Hardware/Software Interface. Chapter 4. The Processor: A Based on P&H
COMPUTER ORGANIZATION AND DESIGN The Hardware/Software Interface Chapter 4 The Processor: A Based on P&H Introduction We will examine two MIPS implementations A simplified version A more realistic pipelined
More informationLecture Topics. Announcements. Today: Single-Cycle Processors (P&H ) Next: continued. Milestone #3 (due 2/9) Milestone #4 (due 2/23)
Lecture Topics Today: Single-Cycle Processors (P&H 4.1-4.4) Next: continued 1 Announcements Milestone #3 (due 2/9) Milestone #4 (due 2/23) Exam #1 (Wednesday, 2/15) 2 1 Exam #1 Wednesday, 2/15 (3:00-4:20
More information4. What is the average CPI of a 1.4 GHz machine that executes 12.5 million instructions in 12 seconds?
Chapter 4: Assessing and Understanding Performance 1. Define response (execution) time. 2. Define throughput. 3. Describe why using the clock rate of a processor is a bad way to measure performance. Provide
More informationECE232: Hardware Organization and Design
ECE232: Hardware Organization and Design Lecture 14: One Cycle MIPs Datapath Adapted from Computer Organization and Design, Patterson & Hennessy, UCB R-Format Instructions Read two register operands Perform
More informationCOMPUTER ORGANIZATION AND DESIGN
COMPUTER ORGANIZATION AND DESIGN 5 Edition th The Hardware/Software Interface Chapter 4 The Processor 4.1 Introduction Introduction CPU performance factors Instruction count CPI and Cycle time Determined
More informationChapter 4. The Processor
Chapter 4 The Processor Introduction CPU performance factors Instruction count Determined by ISA and compiler CPI and Cycle time Determined by CPU hardware We will examine two MIPS implementations A simplified
More informationDesign of a Pipelined 32 Bit MIPS Processor with Floating Point Unit
Design of a Pipelined 32 Bit MIPS Processor with Floating Point Unit P Ajith Kumar 1, M Vijaya Lakshmi 2 P.G. Student, Department of Electronics and Communication Engineering, St.Martin s Engineering College,
More informationCS 251, Winter 2019, Assignment % of course mark
CS 251, Winter 2019, Assignment 5.1.1 3% of course mark Due Wednesday, March 27th, 5:30PM Lates accepted until 1:00pm March 28th with a 15% penalty 1. (10 points) The code sequence below executes on a
More informationEN164: Design of Computing Systems Lecture 09: Processor / ISA 2
EN164: Design of Computing Systems Lecture 09: Processor / ISA 2 Professor Sherief Reda http://scale.engin.brown.edu Electrical Sciences and Computer Engineering School of Engineering Brown University
More informationSystems Architecture I
Systems Architecture I Topics A Simple Implementation of MIPS * A Multicycle Implementation of MIPS ** *This lecture was derived from material in the text (sec. 5.1-5.3). **This lecture was derived from
More information3/12/2014. Single Cycle (Review) CSE 2021: Computer Organization. Single Cycle with Jump. Multi-Cycle Implementation. Why Multi-Cycle?
CSE 2021: Computer Organization Single Cycle (Review) Lecture-10b CPU Design : Pipelining-1 Overview, Datapath and control Shakil M. Khan 2 Single Cycle with Jump Multi-Cycle Implementation Instruction:
More informationMIPS Pipelining. Computer Organization Architectures for Embedded Computing. Wednesday 8 October 14
MIPS Pipelining Computer Organization Architectures for Embedded Computing Wednesday 8 October 14 Many slides adapted from: Computer Organization and Design, Patterson & Hennessy 4th Edition, 2011, MK
More informationChapter 4 The Processor 1. Chapter 4A. The Processor
Chapter 4 The Processor 1 Chapter 4A The Processor Chapter 4 The Processor 2 Introduction CPU performance factors Instruction count Determined by ISA and compiler CPI and Cycle time Determined by CPU hardware
More informationLECTURE 6. Multi-Cycle Datapath and Control
LECTURE 6 Multi-Cycle Datapath and Control SINGLE-CYCLE IMPLEMENTATION As we ve seen, single-cycle implementation, although easy to implement, could potentially be very inefficient. In single-cycle, we
More informationLECTURE 5. Single-Cycle Datapath and Control
LECTURE 5 Single-Cycle Datapath and Control PROCESSORS In lecture 1, we reminded ourselves that the datapath and control are the two components that come together to be collectively known as the processor.
More informationChapter 4. The Processor
Chapter 4 The Processor Introduction CPU performance factors Instruction count Determined by ISA and compiler CPI and Cycle time Determined by CPU hardware We will examine two MIPS implementations A simplified
More informationCENG 3420 Lecture 06: Datapath
CENG 342 Lecture 6: Datapath Bei Yu byu@cse.cuhk.edu.hk CENG342 L6. Spring 27 The Processor: Datapath & Control q We're ready to look at an implementation of the MIPS q Simplified to contain only: memory-reference
More informationMicroprogrammed Control Approach
Microprogrammed Control Approach Considering the FSM for our MIPS subset has 10 states, the complete MIPS instruction set, which contains more than 100 instructions, and considering that these instructions
More informationAdvanced Computer Architecture
Advanced Computer Architecture Chapter 1 Introduction into the Sequential and Pipeline Instruction Execution Martin Milata What is a Processors Architecture Instruction Set Architecture (ISA) Describes
More informationThe Processor: Datapath and Control. Jin-Soo Kim Computer Systems Laboratory Sungkyunkwan University
The Processor: Datapath and Control Jin-Soo Kim (jinsookim@skku.edu) Computer Systems Laboratory Sungkyunkwan University http://csl.skku.edu Introduction CPU performance factors Instruction count Determined
More informationCISC 662 Graduate Computer Architecture. Lecture 4 - ISA
CISC 662 Graduate Computer Architecture Lecture 4 - ISA Michela Taufer http://www.cis.udel.edu/~taufer/courses Powerpoint Lecture Notes from John Hennessy and David Patterson s: Computer Architecture,
More informationLaboratory Pipeline MIPS CPU Design (2): 16-bits version
Laboratory 10 10. Pipeline MIPS CPU Design (2): 16-bits version 10.1. Objectives Study, design, implement and test MIPS 16 CPU, pipeline version with the modified program without hazards Familiarize the
More informationThe Processor: Datapath & Control
Orange Coast College Business Division Computer Science Department CS 116- Computer Architecture The Processor: Datapath & Control Processor Design Step 3 Assemble Datapath Meeting Requirements Build the
More informationECE260: Fundamentals of Computer Engineering
Pipelining James Moscola Dept. of Engineering & Computer Science York College of Pennsylvania Based on Computer Organization and Design, 5th Edition by Patterson & Hennessy What is Pipelining? Pipelining
More informationTopic #6. Processor Design
Topic #6 Processor Design Major Goals! To present the single-cycle implementation and to develop the student's understanding of combinational and clocked sequential circuits and the relationship between
More informationInf2C - Computer Systems Lecture Processor Design Single Cycle
Inf2C - Computer Systems Lecture 10-11 Processor Design Single Cycle Boris Grot School of Informatics University of Edinburgh Previous lectures Combinational circuits Combinations of gates (INV, AND, OR,
More informationCS 265. Computer Architecture. Wei Lu, Ph.D., P.Eng.
CS 265 Computer Architecture Wei Lu, Ph.D., P.Eng. Part 3: von Neumann Architecture von Neumann Architecture Our goal: understand the basics of von Neumann architecture, including memory, control unit
More informationPipelining. CSC Friday, November 6, 2015
Pipelining CSC 211.01 Friday, November 6, 2015 Performance Issues Longest delay determines clock period Critical path: load instruction Instruction memory register file ALU data memory register file Not
More informationCS 61C: Great Ideas in Computer Architecture. MIPS CPU Datapath, Control Introduction
CS 61C: Great Ideas in Computer Architecture MIPS CPU Datapath, Control Introduction Instructor: Alan Christopher 7/28/214 Summer 214 -- Lecture #2 1 Review of Last Lecture Critical path constrains clock
More informationCS 230 Practice Final Exam & Actual Take-home Question. Part I: Assembly and Machine Languages (22 pts)
Part I: Assembly and Machine Languages (22 pts) 1. Assume that assembly code for the following variable definitions has already been generated (and initialization of A and length). int powerof2; /* powerof2
More informationMark Redekopp and Gandhi Puvvada, All rights reserved. EE 357 Unit 15. Single-Cycle CPU Datapath and Control
EE 37 Unit Single-Cycle CPU path and Control CPU Organization Scope We will build a CPU to implement our subset of the MIPS ISA Memory Reference Instructions: Load Word (LW) Store Word (SW) Arithmetic
More informationIntroduction to Computer Engineering. CS/ECE 252 Prof. Mark D. Hill Computer Sciences Department University of Wisconsin Madison
Introduction to Computer Engineering CS/ECE 252 Prof. Mark D. Hill Computer Sciences Department University of Wisconsin Madison Chapter 4 The Von Neumann Model The Stored Program Computer 1943: ENIAC Presper
More informationComputer Architecture. Lecture 6.1: Fundamentals of
CS3350B Computer Architecture Winter 2015 Lecture 6.1: Fundamentals of Instructional Level Parallelism Marc Moreno Maza www.csd.uwo.ca/courses/cs3350b [Adapted from lectures on Computer Organization and
More informationChapter 4. The Processor Designing the datapath
Chapter 4 The Processor Designing the datapath Introduction CPU performance determined by Instruction Count Clock Cycles per Instruction (CPI) and Cycle time Determined by Instruction Set Architecure (ISA)
More informationCOMPUTER ORGANIZATION AND DESIGN
ARM COMPUTER ORGANIZATION AND DESIGN Edition The Hardware/Software Interface Chapter 4 The Processor Modified and extended by R.J. Leduc - 2016 To understand this chapter, you will need to understand some
More informationCISC 662 Graduate Computer Architecture. Lecture 4 - ISA MIPS ISA. In a CPU. (vonneumann) Processor Organization
CISC 662 Graduate Computer Architecture Lecture 4 - ISA MIPS ISA Michela Taufer http://www.cis.udel.edu/~taufer/courses Powerpoint Lecture Notes from John Hennessy and David Patterson s: Computer Architecture,
More informationRui Wang, Assistant professor Dept. of Information and Communication Tongji University.
Instructions: ti Language of the Computer Rui Wang, Assistant professor Dept. of Information and Communication Tongji University it Email: ruiwang@tongji.edu.cn Computer Hierarchy Levels Language understood
More informationChapter 5: Computer Systems Organization
Objectives Chapter 5: Computer Systems Organization Invitation to Computer Science, C++ Version, Third Edition In this chapter, you will learn about: The components of a computer system Putting all the
More informationChapter 5: Computer Systems Organization. Invitation to Computer Science, C++ Version, Third Edition
Chapter 5: Computer Systems Organization Invitation to Computer Science, C++ Version, Third Edition Objectives In this chapter, you will learn about: The components of a computer system Putting all the
More informationChapter 4 The Von Neumann Model
Chapter 4 The Von Neumann Model The Stored Program Computer 1943: ENIAC Presper Eckert and John Mauchly -- first general electronic computer. (or was it John V. Atananasoff in 1939?) Hard-wired program
More informationECE331: Hardware Organization and Design
ECE331: Hardware Organization and Design Lecture 35: Final Exam Review Adapted from Computer Organization and Design, Patterson & Hennessy, UCB Material from Earlier in the Semester Throughput and latency
More informationThe MIPS Processor Datapath
The MIPS Processor Datapath Module Outline MIPS datapath implementation Register File, Instruction memory, Data memory Instruction interpretation and execution. Combinational control Assignment: Datapath
More informationLECTURE 3: THE PROCESSOR
LECTURE 3: THE PROCESSOR Abridged version of Patterson & Hennessy (2013):Ch.4 Introduction CPU performance factors Instruction count Determined by ISA and compiler CPI and Cycle time Determined by CPU
More informationLecture 10: Simple Data Path
Lecture 10: Simple Data Path Course so far Performance comparisons Amdahl s law ISA function & principles What do bits mean? Computer math Today Take QUIZ 6 over P&H.1-, before 11:59pm today How do computers
More informationControl Hazards - branching causes problems since the pipeline can be filled with the wrong instructions.
Control Hazards - branching causes problems since the pipeline can be filled with the wrong instructions Stage Instruction Fetch Instruction Decode Execution / Effective addr Memory access Write-back Abbreviation
More informationFaculty of Science FINAL EXAMINATION
Faculty of Science FINAL EXAMINATION COMPUTER SCIENCE COMP 273 INTRODUCTION TO COMPUTER SYSTEMS Examiner: Prof. Michael Langer April 18, 2012 Associate Examiner: Mr. Joseph Vybihal 2 P.M. 5 P.M. STUDENT
More informationCPE 335 Computer Organization. Basic MIPS Architecture Part I
CPE 335 Computer Organization Basic MIPS Architecture Part I Dr. Iyad Jafar Adapted from Dr. Gheith Abandah slides http://www.abandah.com/gheith/courses/cpe335_s8/index.html CPE232 Basic MIPS Architecture
More informationCENG 3420 Computer Organization and Design. Lecture 06: MIPS Processor - I. Bei Yu
CENG 342 Computer Organization and Design Lecture 6: MIPS Processor - I Bei Yu CEG342 L6. Spring 26 The Processor: Datapath & Control q We're ready to look at an implementation of the MIPS q Simplified
More informationCPE 335. Basic MIPS Architecture Part II
CPE 335 Computer Organization Basic MIPS Architecture Part II Dr. Iyad Jafar Adapted from Dr. Gheith Abandah slides http://www.abandah.com/gheith/courses/cpe335_s08/index.html CPE232 Basic MIPS Architecture
More informationComputer Science 324 Computer Architecture Mount Holyoke College Fall Topic Notes: MIPS Instruction Set Architecture
Computer Science 324 Computer Architecture Mount Holyoke College Fall 2009 Topic Notes: MIPS Instruction Set Architecture vonneumann Architecture Modern computers use the vonneumann architecture. Idea:
More informationLECTURE 10. Pipelining: Advanced ILP
LECTURE 10 Pipelining: Advanced ILP EXCEPTIONS An exception, or interrupt, is an event other than regular transfers of control (branches, jumps, calls, returns) that changes the normal flow of instruction
More informationInstruction Pipelining
Instruction Pipelining Simplest form is a 3-stage linear pipeline New instruction fetched each clock cycle Instruction finished each clock cycle Maximal speedup = 3 achieved if and only if all pipe stages
More informationChapter 4. The Processor. Computer Architecture and IC Design Lab
Chapter 4 The Processor Introduction CPU performance factors CPI Clock Cycle Time Instruction count Determined by ISA and compiler CPI and Cycle time Determined by CPU hardware We will examine two MIPS
More informationCC411: Introduction To Microprocessors
CC411: Introduction To Microprocessors OBJECTIVES this chapter enables the student to: Use number { base 2, base 10, or base 16 }. Add and subtract binary/hex numbers. Represent any binary number in 2
More informationInstruction Pipelining
Instruction Pipelining Simplest form is a 3-stage linear pipeline New instruction fetched each clock cycle Instruction finished each clock cycle Maximal speedup = 3 achieved if and only if all pipe stages
More informationChapter 4 The Von Neumann Model
Chapter 4 The Von Neumann Model The Stored Program Computer 1943: ENIAC Presper Eckert and John Mauchly -- first general electronic computer. (or was it John V. Atanasoff in 1939?) Hard-wired program --
More informationDual Port SRAM Based Microcontroller Chip Test Report
Dual Port SRAM Based Microcontroller Chip Test Report By Sergey Kononov, et al. Chip Description Fig. 1: Chip Layout, Pin Configuration The Chip consists of 3 main components: Dual Port SRAM (DPRAM), test
More informationThis course provides an overview of the SH-2 32-bit RISC CPU core used in the popular SH-2 series microcontrollers
Course Introduction Purpose: This course provides an overview of the SH-2 32-bit RISC CPU core used in the popular SH-2 series microcontrollers Objectives: Learn about error detection and address errors
More informationComputer Organization and Structure
Computer Organization and Structure 1. Assuming the following repeating pattern (e.g., in a loop) of branch outcomes: Branch outcomes a. T, T, NT, T b. T, T, T, NT, NT Homework #4 Due: 2014/12/9 a. What
More informationThe Processor (1) Jinkyu Jeong Computer Systems Laboratory Sungkyunkwan University
The Processor (1) Jinkyu Jeong (jinkyu@skku.edu) Computer Systems Laboratory Sungkyunkwan University http://csl.skku.edu EEE3050: Theory on Computer Architectures, Spring 2017, Jinkyu Jeong (jinkyu@skku.edu)
More informationR-type Instructions. Experiment Introduction. 4.2 Instruction Set Architecture Types of Instructions
Experiment 4 R-type Instructions 4.1 Introduction This part is dedicated to the design of a processor based on a simplified version of the DLX architecture. The DLX is a RISC processor architecture designed
More informationCSE 2021 COMPUTER ORGANIZATION
CSE 2021 COMPUTER ORGANIZATION HUGH LAS CHESSER 1012U HUGH CHESSER CSEB 1012U W10-M Agenda Topics: 1. Multiple cycle implementation review 2. State Machine 3. Control Unit implementation for Multi-cycle
More informationName: University of Michigan uniqname: (NOT your student ID number!)
The University of Michigan - Department of EECS EECS370 Introduction to Computer Organization Midterm Exam 1 October 22, 2009 Name: University of Michigan uniqname: (NOT your student ID number!) Open book,
More informationCS3350B Computer Architecture Quiz 3 March 15, 2018
CS3350B Computer Architecture Quiz 3 March 15, 2018 Student ID number: Student Last Name: Question 1.1 1.2 1.3 2.1 2.2 2.3 Total Marks The quiz consists of two exercises. The expected duration is 30 minutes.
More informationCS 251, Winter 2018, Assignment % of course mark
CS 251, Winter 2018, Assignment 5.0.4 3% of course mark Due Wednesday, March 21st, 4:30PM Lates accepted until 10:00am March 22nd with a 15% penalty 1. (10 points) The code sequence below executes on a
More informationCSE140: Components and Design Techniques for Digital Systems
CSE4: Components and Design Techniques for Digital Systems Tajana Simunic Rosing Announcements and Outline Check webct grades, make sure everything is there and is correct Pick up graded d homework at
More informationThe Processor Pipeline. Chapter 4, Patterson and Hennessy, 4ed. Section 5.3, 5.4: J P Hayes.
The Processor Pipeline Chapter 4, Patterson and Hennessy, 4ed. Section 5.3, 5.4: J P Hayes. Pipeline A Basic MIPS Implementation Memory-reference instructions Load Word (lw) and Store Word (sw) ALU instructions
More informationTopic Notes: MIPS Instruction Set Architecture
Computer Science 220 Assembly Language & Comp. Architecture Siena College Fall 2011 Topic Notes: MIPS Instruction Set Architecture vonneumann Architecture Modern computers use the vonneumann architecture.
More informationChapter 5: The Processor: Datapath and Control
Chapter 5: The Processor: Datapath and Control Overview Logic Design Conventions Building a Datapath and Control Unit Different Implementations of MIPS instruction set A simple implementation of a processor
More informationICS 233 COMPUTER ARCHITECTURE. MIPS Processor Design Multicycle Implementation
ICS 233 COMPUTER ARCHITECTURE MIPS Processor Design Multicycle Implementation Lecture 23 1 Add immediate unsigned Subtract unsigned And And immediate Or Or immediate Nor Shift left logical Shift right
More informationDigital System Design Using Verilog. - Processing Unit Design
Digital System Design Using Verilog - Processing Unit Design 1.1 CPU BASICS A typical CPU has three major components: (1) Register set, (2) Arithmetic logic unit (ALU), and (3) Control unit (CU) The register
More informationComputer Architecture V Fall Practice Exam Questions
Computer Architecture V22.0436 Fall 2002 Practice Exam Questions These are practice exam questions for the material covered since the mid-term exam. Please note that the final exam is cumulative. See the
More informationThe von Neumann Architecture. IT 3123 Hardware and Software Concepts. The Instruction Cycle. Registers. LMC Executes a Store.
IT 3123 Hardware and Software Concepts February 11 and Memory II Copyright 2005 by Bob Brown The von Neumann Architecture 00 01 02 03 PC IR Control Unit Command Memory ALU 96 97 98 99 Notice: This session
More informationImplementing the Control. Simple Questions
Simple Questions How many cycles will it take to execute this code? lw $t2, 0($t3) lw $t3, 4($t3) beq $t2, $t3, Label add $t5, $t2, $t3 sw $t5, 8($t3) Label:... #assume not What is going on during the
More informationCS 351 Exam 2 Mon. 11/2/2015
CS 351 Exam 2 Mon. 11/2/2015 Name: Rules and Hints The MIPS cheat sheet and datapath diagram are attached at the end of this exam for your reference. You may use one handwritten 8.5 11 cheat sheet (front
More informationBASIC COMPUTER ORGANIZATION. Operating System Concepts 8 th Edition
BASIC COMPUTER ORGANIZATION Silberschatz, Galvin and Gagne 2009 Topics CPU Structure Registers Memory Hierarchy (L1/L2/L3/RAM) Machine Language Assembly Language Running Process 3.2 Silberschatz, Galvin
More informationbits 5..0 the sub-function of opcode 0, 32 for the add instruction
CS2 Computer Systems note 1a Some MIPS instructions More details on these, and other instructions in the MIPS instruction set, can be found in Chapter 3 of Patterson and Hennessy. A full listing of MIPS
More informationBlock diagram view. Datapath = functional units + registers
Computer design an application of digital logic design procedures Computer = processing unit + memory system Processing unit = control + datapath Control = finite state machine inputs = machine instruction,
More informationChapter 4 The Von Neumann Model
Chapter 4 The Von Neumann Model The Stored Program Computer 1943: ENIAC Presper Eckert and John Mauchly -- first general electronic computer. (or was it John V. Atanasoff in 1939?) Hard-wired program --
More information