ACE BACKSTAGE CO., INC.

Transcription

1 PUSH PUSH ACE BACKSTAGE CO. CLEAR COM DMX12 ACE BACKSTAGE CO., INC. STAGE POCKET SYSTEMS Stage Pocket Systems / Panel Fabrication / Spec Fabrication / Stage Management Products COMPARE 122SLBK Full Stage Pocket Page 4 CONNECTORS CONNECTRIX, Neutrik & Switchcraft Page 19 STAGE MANAGEMENT Solutions to Common Problems Page 23 PANELS CUSTOM SPEC FABRICATION CONNECTRIX and Custom Spec Pockets and Panels Page 21 Page Avenue Rockefeller Suite 200 Valencia, CA Issue #612 Tel: Fax: Web:

2 ACE POCKET SELECTION GUIDE VERTICAL SLANT PANEL POCKETS CONNECTRIX See Pages 19 for details STANDARD GENERAL USE VERTICAL SLANT PANEL POCKETS feature an open access design to make installing connector panels easy. They are load tested to withstand commercial point loads while preventing connector damage. Hard finished with electrostatic powder coat in two neutral colors, as well as designer finishes for a clean appearance. Installed as part of the ACE Pocket System, these pockets can be used in all floor types and can accommodate up to 24 connections. See pages for panel and connector details. Mini Pocket Pages Half Pocket Pages Full Pocket Pages 4-5 Double Wide Pocket Pages 6-7 Load Test Results Capacity: Up to (4) CONNECTRIX Connectors Capacity: Up to (6) CONNECTRIX Connectors Capacity: Up to (12) CONNECTRIX Connectors Capacity: Up to (24) CONNECTRIX Connectors HORIZONTAL PANEL POCKETS CONNECTRIX See Pages 19 for details SUPER CAPACITY HORIZONTAL PANEL POCKETS have increased, super capacity, of up to 50 connections using horizontally mounted panel brackets in the back-box pocket body. They offer the same rugged construction, finishes, and weight load verification with twice the connectivity as our vertical panel pockets. This two-piece pocket consists of a separate back box-pocket body and lid/bezel. *Note: Connector capacity limitations apply depending on connectors and panels used. Super Pocket Pages 8-9 Capacity: Up to (25) CONNECTRIX Connectors Super Double Wide Pocket Pages Capacity: Up to (50) CONNECTRIX Connectors TABLE TOP POCKETS CONNECTRIX See Pages 19 for details TABLE TOP POCKETS were developed to provide easy conference room access to all types of necessary connectivity. Easily installed into any table top, these pockets allow convenient power, and panel mounted or cable-end connections. Built to withstand institutional use and complemented with features that protect the pocket and itõ s connections. Available in our signature black powder coat finish, each table top pocket can accommodate up to 12 connections. *Note: Connector capacity limitations apply depending on connectors and panels used. Table Top Pocket Page 22 Capacity: Up to (12) CONNECTRIX Connectors Conference Port Pages 22 Capacity: (8) or More Cables PSW-100 ACE CONNECTRIX PANEL GUIDE CONNECTRIX POCKET PANELS (Page 20) CONNECTRIX WALL & RACK PANELS (Page 21) POCKET PANELS are cut, coated, engraved and loaded in house. Designed as part of the ACE Pocket System, these panels are flat and strong. They mate perfectly with ACE Pockets and utilize our CONNECTRIX cutout detail to combine custom connector options and immediate delivery. WALL & RACK PANELS come in standard sizes, but can also be made to your custom needs. Rack panels are immediately available in semi gloss black and wall panels come in semi gloss black or white. Featuring our CONNECTRIX cutout detail, ACE Wall and Rack Panels maximize the number of connectors on each panel. Custom connector engraving and company logo engraving adds a professional flair. CONNECTRIX See Pages 19 for details 2 ACE BACKSTAGE CO., INC Avenue Rockefeller Suite 200 Valencia, CA Tel: Fax:

3 ACE BACK BOX SELECTION GUIDE BACK BOXES BACK BOXES are designed exclusively for use with ACE vertical panel pockets and are finished in electro deposited zinc for corrosion resistance. Available in many depths, allowing clearance for feed through or distribution junction, using combination knock-outs. Welded steel construction includes a disposable protective cover and accepts accessory brackets for isolation of high and low voltage. See pages for back box details. 6 Deep Pages 17 Isolated 8 Deep Pages Deep Pages 17 Isolated Moisture Resistant Coating Pages 17 BACK ACCESS COVERS are used to close the back access opening in ACE vertical panel pockets after wires have been terminated. Use a BAC in a raised floor installation, and add an isolation bracket when separation of high and low voltage is necessary. See page 16 for back access cover details. BACK ACCESS COVERS Back Access Cover Pages 16 Isolated Back Access Cover Pages 16 ACE STAGE MANAGEMENT GUIDE STAGE MANAGEMENT PRODUCTS were created to offer solutions to installation challenges. A variety of items, each one specifically addressing an installation hassle, and offering a simple solution. See page 23 for stage management product details. Choir Stick Microphone Pages 23 Microphone Softpod Pages 23 Mic Hanger Slug Pages 23 ACE CONNECTRIX CONNECTOR GUIDE CONNECTRIX Connectors eliminate the need for a custom cut panel. Our modular system seamlessly mates each connector into prepunched cutouts in our CONNECTRIX Panels. Using this system, we can ship pocket panels, wall panels, or rack panels immediately. No need to wait for a custom cut panel. See page 19 for connector details. Single Space Double Space Triple Space Pages 19 Pages 19 Pages 19 CUSTOM POCKET AND PANEL FABRICATION ACEÕ scustom Spec Panel Fabrication Services produce panels which are precision cut and engraved to your exact specifications from a variety of materials on precision CNC rotary cutting machines. ACEÕ s Custom Services also include Custom Spec Pocket Fabrication Services See page 21 for custom panel engraving and fabrication details. See Back Cover for custom spec pocket details. Custom Spec Pockets Back Cover Custom Engraved Panels Page 21 Input Input Trigger Trigger DC-4500 SEISMOELECTRONICS GROUNDWATER LOCATOR LOCATOR USB to Computer USB to Computer Battery Charge Power Battery Charge Power ACE BACKSTAGE CO., INC Avenue Rockefeller Suite 200 Valencia, CA Tel: Fax:

4 FULL STAGE POCKET 122SLBK - FULL POCKET The Full Stage Pocket by ACE Backstage Co., Inc. is made from heavy gauge, die-cut steel. This professional box provides a rugged, flush mounted space to conceal and protect stage connections. The vertical slant panel design provides an open access to the conduit, allowing connector panels to be terminated before or after pocket installation. This feature brings flexibility to the installation process, allowing rough-in or completion-stage connector termination. CONNECTRIX SYSTEM READY All ACE Stage Pockets are compatible with interchangeable CONNECTRIX System Panels and isolated connector configurations. Designed to maximize space and allow adequate receptacle clearance, CONNECTRIX Panels house a larger number of connections than a standard ganged plate and allow for a customized configuration. For more information on CONNECTRIX Panels see pg. 20 For more information on CONNECTRIX Connectors see pg. 19 ACE STAGE POCKETS Standard Vertical Slant Panel Super Horizontal Slant Panel CONNECTOR CAPACITY Up to (12) connections or (6) connections & (1) dual gang A/C x 12 OR + x 6 x 2 ((((4 (4) 4)) ) (6)))) ( (12) (24) ((((24 4))))) (25) ((((25 25)))) (50) ((((50 50)))) Lid and Flange Measurement: Body Measurement: FEATURES 10.5 L x 10.5 W x D L x 8.0 W x 4.5 D PANEL OPTIONS Floor Cutout Size: 8.5 x 8.5 Cableway Slot: 3/8 x 8 Powder Coat Finishes: Special Order Lid & Bezel: Textured Black Decorator (BK) Antique Coppervein (CV) Solid Brass (BR) Stainless Steel (SS) Interchangeable Lids: Standard Lid (SL) Locking Lid (LL) Carpet Lid (CL) Modified Length Lid (ML) UL Listed: Panel Placement: Yes Vertical Compatible ACE Panel Series: PE PNL-100 PNL-120 PSW-100 #MP-100 PNL-100 PSW-100 #PE #PNL-120 INCLUDES (1) Vertical, Slant Panel Style, Stage Pocket (1) Interchangeable Lid (2) Hinge Pins and Spring Fasteners (8) Installation Screws (1) Capture Slot Closure OPTIONS #PNL-140 UL LISTED Locking Lid Enlarged Cable Exit Carpet Lid Back Access Cover Back Box UL Listed compliance Standard 514A file FLOOR BOX 44LK Suitable for raised floor applications pg. 16 pg ACE BACKSTAGE CO., INC Avenue Rockefeller Suite 200 Valencia, CA Tel: Fax:

5 FRONT VIEW 4 PROUDLY MADE IN THE U.S.A. VERTICAL SLANT POCKET OPTIONAL BACK BOX WELDED 14 GAUGE FULL 8.000" 8.250" STAGE POCKET 6.000" " CAPTIVE SLOT CLOSURE DROPS INTO BOX WHEN CABLE WAY SLOT IS IN USE NOMINAL OPENING TOP VIEW 10 CONNECTRIX A FLEXIBLE CONNECTOR AND PANEL SYSTEM Choose Pre-fabricated audio, communications, data, electric, video, and voice connectors and panels, or create custom panels as needed using the CONNECTRIX System of panels and connectors. REMOVABLE HINGE PINS PERMIT EASY LID EXCHANGE FOR CUSTOM LID CONFIGURATIONS 8.5" x 8.5" CUTOUT IN STAGE FLOOR WHEN MOUNTING IN STAGE FLOOR WITHOUT ACE #102BBX BACK BOX CAPTIVE SLOT CLOSURE DROPS INTO BOX WHEN CABLE WAY SLOT IS IN USE.375" CABLE WAY SLOT SECTION VIEW OPEN BACK ACCESS 6.000" 4 59/64" NOM " NOM " 1 NOMINAL 3.656" 8.000" 7.187" 16 GAUGE (.060" THICK) WELDED STEEL POCKET BODY CONSTRUCTION TRIM BEZEL " OPEN ACCESS FRONT VIEW OPTIONAL BACK BOX WELDED 14 GAUGE " 8.000" 8.250" " Download DWG & DXF AutoCAD, and PDF Spec Sheets for ALL ACE Stage Pockets at STANDARD POCKET PANELS FOR USE WITH 122XXXX HALF PANEL PNL-100/PSW-100 SERIES OPEN BACK APPROVALS SECTION VIEW DATE ACCESS FINISH DRAWN Electrostatic applied 1.875" NOM. powdercoat 3.656" CUSTOMER APPROVAL 1 NOMINAL 8.000" " FULL PANEL PNL-120 SERIES 7.187" 16 GAUGE (.060" THICK) WELDED STEEL POCKET BODY CONSTRUCTION ELECTRICAL PANEL REMOVABLE HINGE PINS PERMIT EASY LID EXCHANGE FOR CUSTOM LID CONFIGURATIONS PE SERIES MODEL # #122CLBK #122CLCV #122LLBK #122SLBK #122SLCV #222CLBR #222SLBR #322CLSS #322SLSS MATERIAL 11ga CRS - Lid & Flange 16ga CRS - Pocket Body FULL POCKET MODEL NUMBERS Black Full Pocket w/ Carpet Lid Copper Vein Full Pocket w/ Carpet Lid Black Full Pocket w/ Lid Punched for Lock Black Full Pocket w/ Standard Lid Copper Vein Full Pocket w/ Standard Lid Brass Full Pocket w/ Carpet Lid Brass Full Pocket w/ Standard Lid Stainless Steel Full Pocket w/ Carpet Lid Stainless Steel Full Pocket w/ Standard Lid ITEM 122XXXX Full-sized floor pocket to house up to (12) connectors

6 DOUBLE WIDE POCKET 124SLBK - DOUBLE WIDE POCKET The size of this Double Wide Pocket allows for a large connector capacity in a flush mounted, vertical slant panel pocket. Built from cold roll steel, die pressed and expertly welded, forming a consistently square, dimensionally stabile enclosure to conceal connectivity and prevent connector damage. Use the interchangeable CONNECTRIX Panel System when designing your connector configuration to include audio, video, electric AC power, data, control, and switches. CONNECTRIX SYSTEM READY All ACE Stage Pockets are compatible with interchangeable CONNECTRIX System Panels and isolated connector configurations. Designed to maximize space and allow adequate receptacle clearance, CONNECTRIX Panels house a larger number of connections than a standard ganged plate and allow for a customized configuration. For more information on CONNECTRIX Panels see pg. 20 For more information on CONNECTRIX Connectors see pg. 19 ACE STAGE POCKETS Standard Vertical Slant Panel Super Horizontal Slant Panel CONNECTOR CAPACITY Up to (24) connections or (12) connections and (2) dual gang A/C x 24 OR x 12 + x 4 (4) (6) (12) (24) (25) (50) Lid and Flange Measurement: Body Measurement: FEATURES 18.5 L x 10.5 W x D L x 16 W x 4.5 D PANEL OPTIONS Floor Cutout Size: 8.5 x 16.5 Cableway Slot: 3/8 x 16 Powder Coat Finishes: Special Order Lid & Bezel: Textured Black Decorator (BK) Antique Coppervein (CV) Solid Brass (BR) Stainless Steel (SS) Interchangeable Lids: Standard Lid (SL) Locking Lid (LL) Carpet Lid (CL) Modified Length Lid (ML) UL Listed: Panel Placement: Yes Vertical Compatible ACE Panel Series: PNL-100 PNL-120 PSW-100 PE FP3E #MP-100 PNL-100 PSW-100 #PE #PNL-120 INCLUDES (1) Vertical, Slant Panel Style, Stage Pocket (1) Interchangeable Lid (2) Hinge Pins and Spring Fasteners (16) Installation Screws (2) Capture Slot Closures OPTIONS #PNL-140 UL LISTED Locking Lid Enlarged Cable Exit Carpet Lid Back Access Cover Back Box UL Listed compliance Standard 514A file FLOOR BOX 44LK Suitable for raised floor applications pg. 16 pg ACE BACKSTAGE CO., INC Avenue Rockefeller Suite 200 Valencia, CA Tel: Fax:

7 PROUDLY MADE IN THE U.S.A. VERTICAL SLANT POCKET DOUBLE WIDE STAGE POCKET (2) CAPTIVE SLOT CLOSURES DROP INTO BOX WHEN CABLEWAY SLOT IS IN USE NOMINAL OPENING CONNECTRIX A FLEXIBLE CONNECTOR AND PANEL SYSTEM Choose Pre-fabricated audio, communications, data, electric, video, and voice connectors and panels, or create custom panels as needed using the CONNECTRIX System of panels and connectors. REMOVABLE HINGE PINS PERMIT EASY LID EXCHANGE FOR CUSTOM LID CONFIGURATIONS " TOP VIEW 11 GAUGE (.120" THICK) STEEL TRIM BEZEL AND LID ASSEMBLY WITH POWDER COAT FINISH INSIDE AND OUTSIDE ANTIQUE COPPER VEIN TEXTURED BLACK BRUSHED BRASS* STAINLESS STEEL* *Solid Brass or Stainless Steel Metal *Finish Available as Special Order " SECTION VIEW OPEN BACK ACCESS " 59/64" NOM " NOM. 16.8" x 8.5" CUTOUT IN STAGE FLOOR WHEN MOUNTING IN STAGE FLOOR WITHOUT ACE #104BBX BACK BOX 3.656" 1 NOMINAL 8.000" 7.187" 16 GAUGE (.060" THICK) WELDED STEEL POCKET BODY CONSTRUCTION ".375" CABLE WAY SLOT " TYPICAL TRIM BEZEL (2) CAPTIVE SLOT CLOSURES DROP INTO BOX WHEN CABLE WAY SLOT IS IN USE TRIM BEZEL Download DWG & DXF AutoCAD, and PDF Spec Sheets for ALL ACE Stage Pockets at " OPTIONAL BACK BOX WELDED 14 GAUGE (.071" THICK) STEEL 10" X 18" X 6" ZINC PLATED (ACE #104BBX BACK BOX) OR OPTIONAL BACK ACCESS COVER 14 GAUGE (.071" THICK) STEEL ZINC PLATED (ACE #24BAC BACK ACCESS COVER - NOT SHOWN) FRONT VIEW " " " STANDARD POCKET PANELS FOR USE WITH 124XXXX HALF PANEL FULL PANEL ELECTRICAL PANEL PNL-100/PSW-100 SERIES PNL-120 SERIES PE SERIES DOUBLE WIDE POCKET MODEL NUMBERS MODEL # #124CLBK Black Double Wide Pocket w/ Carpet Lid #124CLCV Copper Vein Double Wide Pocket w/ Carpet Lid #124LLBK Black Double Wide Pocket w/ Lid Punched for Lock #124SLBK Black Double Wide Pocket w/ Standard Lid #124SLCV Copper Vein Double Wide Pocket w/ Standard Lid #224CLBR Brass Double Wide Pocket w/ Carpet Lid #224SLBR Brass Double Wide Pocket w/ Standard Lid #324CLSS Stainless Steel Double Wide Pocket w/ Carpet Lid #324SLSS Stainless Steel Double Wide Pocket w/ Standard Lid APPROVALS DATE FINISH DRAWN Electrostatic applied powdercoat CUSTOMER APPROVAL MATERIAL 10ga CRS - Lid & Flange 16ga CRS - Pocket Body ITEM 124XXXX Double-wide floor pocket to house up to (24) connectors

8 SUPER STAGE POCKET 132SLBK - SUPER STAGE POCKET Introducing ACE s large-capacity, horizontal panel mount pocket. It has the same above floor footprint as the standard Full Pocket (10.5 x 10.5 ) with almost three times the connectivity. Built from die-cut heavy gauge welded steel, the ACE Super Pocket resists bending even under the most severe stage loads. The Super Pocket system incorporates three sub-assemblies, allowing just in time delivery for each phase of construction. Phase #1 The pocket body incorporates horizontal panel brackets with an isolated AC raceway enclosure, mounted inside a full sized ACE steel back box. Generous combination knockouts provide in, out, and thru ways for cabling. If ordered separately: BRK102BBX. Phase #2 Pre-loaded connectors can be easily terminated during this phase before the stage floor is finished, enabling the installer to solder without worry of disturbing the finished floor. CONNECTRIX Panels arrive loaded with CONNECTRIX Connectors and can be custom engraved per your specifications. *Replace the back box cover to protect the pockets internal assembly until phase 3. Phase #3 The unique lid and bezel assembly mounts directly to the installed pocket body, allowing concealed connectivity to be accessed through the blind-hinged lid. If ordered separately: BZ132XXYY CONNECTRIX SYSTEM READY ACE STAGE POCKETS Standard Vertical Slant Panel Super Horizontal Slant Panel (4) (6) (12) (24) (25) (50) Lid and Flange Measurement: Body Measurement: FEATURES 10.5 L x 10.5 W x D 10.0 L x 10.0 W x 6.0 D Floor Cutout Size: 10.0 x 10.0 Cableway Slot: 3/8 x 8 Powder Coat Finishes: Textured Black Decorator (BK) Antique Coppervein (CV) All ACE Stage Pockets are compatible with interchangeable CONNECTRIX System Panels and isolated connector configurations. Designed to maximize space and allow adequate receptacle clearance, CONNECTRIX Panels house a larger number of connections than a standard ganged plate and allow for a customized configuration. When using PNL-140 Series Panels, Choose from CONNECTRIX Connector series: C C C C For more information on CONNECTRIX Panels see pg. 20 For more information on CONNECTRIX Connectors see pg. 19 CONNECTOR CAPACITY Up to (25) connections and (2) dual gang A/C x 25 + x 4 Special Order Lid & Bezel: Solid Brass (BR) Stainless Steel (SS) COMPLETE SYSTEM INCLUDES Interchangeable Lids: Standard Lid (SL) Locking Lid (LL) Carpet Lid (CL) Modified Length Lid (ML) UL Listed: Panel Placement: Yes Horizontal Compatible ACE Panels: PNL-100 PNL-120 PNL-140 PSW-100 UL LISTED (1) Back Box Pocket Body with Horizontal Panel Brackets Installed (1) Interchangeable Lid (2) Hinge Pins and Springs (8) Installation Screws (1) Capture Slot Closure Locking Lid Enlarged Cable Exit OPTIONS Carpet Lid Extended Back Box UL Listed compliance Standard 514A file FLOOR BOX 44LK Suitable for raised floor applications pg ACE BACKSTAGE CO., INC Avenue Rockefeller Suite 200 Valencia, CA Tel: Fax:

9 PROUDLY MADE IN THE U.S.A. HORIZONTAL PANEL POCKET SUPER STAGE POCKET.375" CABLE WAY SLOT NOMINAL OPENING LID (BLIND HINGE), SPRING LOADED PINS, AVAILABLE IN STANDARD FLUSH, STANDARD FLUSH LOCKING, OR RECESSED CARPET REMOVABLE SPRING LOADED HINGE PINS PERMIT EASY LID EXCHANGE FOR CARPET, LOCKING, AND STANDARD LID CONFIGURATIONS TRIM BEZEL MOUNTING FLANGE & LID ASSEMBLY 8.000" SUPER STAGE POCKET BACK BOX #BRK102BBX 3.375" CONNECTRIX PANEL SYSTEM COMBINATION OF "#PNL-100", "#PNL-120", OR "#PNL-140" STAGE POCKET PANELS BARRIER ISOLATED AC SECTION CREATED WHEN #BRK102 BRACKET KIT ASSEMBLY IS INSTALLED Download DWG & DXF AutoCAD, and PDF Spec Sheets for ALL ACE Stage Pockets at NOMINAL OPENING 2.335" BARRIER ISOLATED LOW VOLTAGE SECTION CREATED WHEN #BRK102 BRACKET KIT ASSEMBLY IS INSTALLED LID (BLIND HINGE), SPRING LOADED PINS, AVAILABLE IN STANDARD FLUSH, STANDARD FLUSH LOCKING, OR RECESSED CARPET STANDARD POCKET PANELS FOR USE WITH 132XXXX TRIM BEZEL MOUNTING FLANGE & LID ASSEMBLY HALF PANEL PNL-100 SERIES PSW-100 SERIES 2.335" APPROVALS DATE BRACKET KIT ASSEMBLY FINISH IS INSTALLED DRAWN Electrostatic applied 7.250" 2.530" powdercoat CUSTOMER APPROVAL FULL PANEL SUPER STAGE POCKET BACK BOX #BRK102BBX 3.375" PNL-120 SERIES 8.000" REMOVABLE SPRING LOADED HINGE PINS PERMIT EASY LID EXCHANGE FOR CARPET, LOCKING, AND STANDARD LID CONFIGURATIONS A/C COVER BARRIER ISOLATED AC SECTION CREATED WHEN PE #BRK102 SERIESBRACKET KIT DC/DB ASSEMBLY PANELS IS INSTALLED " SQUARE CONNECTRIX PANEL SYSTEM COMBINATION OF "#PNL-100", "#PNL-120", OR "#PNL-140" STAGE POCKET PANELS BARRIER ISOLATED LOW VOLTAGE SECTION CREATED WHEN #BRK102 SUPER PANEL PNL-140 SERIES MODEL # #132CLBK #132CLCV #132LLBK #132SLBK #132SLCV #232CLBR #232SLBR #332CLSS #332SLSS MATERIAL 11ga CRS - Lid & Flange 14ga CRS - Pocket Body 7.250" " SQUARE SUPER STAGE POCKET MODEL NUMBERS ITEM 2.530" Black Super Pocket w/ Carpet Lid Copper Vein Super Pocket w/ Carpet Lid Black Super Pocket w/ Lid Punched for Lock Black Super Pocket w/ Standard Lid Copper Vein Super Pocket w/ Standard Lid Brass Super Pocket w/ Carpet Lid Brass Super Pocket w/ Standard Lid Stainless Steel Super Pocket w/ Carpet Lid Stainless Steel Super Pocket w/ Standard Lid 132XXXX Super floor pocket to house up to (25) connectors

10 SUPER DOUBLE WIDE POCKET 134SLBK - SUPER DOUBLE WIDE POCKET ACE Backstage Co., Inc s Super Double Wide Pocket is designed for high capacity connectivity in a horizontal panel mount configuration. ACEÕ s unique pocket design uses a reinforced hinge-tube, heavy duty lid stops, and a wide mounting bezel to distribute weight loads. The Super Double Wide Pocket system incorporates three subassemblies, allowing just in time delivery of each part for each phase of construction. Phase #1 The pocket body incorporates horizontal panel brackets, mounted inside a double wide sized ACE steel back box. Generous combination knockouts provide in, out, and thru ways for cabling. If ordered separately: BRK104BBX. Phase #2 Pre-loaded connectors can be easily terminated during this phase before the stage floor is finished, enabling the installer to solder without worry of disturbing the finished floor. CONNECTRIX Panels arrive loaded with CONNECTRIX Connectors and can be custom engraved per your specifications. *Replace the back box cover to protect the pockets internal assembly until phase 3. Phase #3 The unique lid and bezel assembly mounts directly to the installed pocket body, allowing concealed connectivity to be accessed through the blind-hinged lid. If ordered separately: BZ134XXYY CONNECTRIX SYSTEM READY ACE STAGE POCKETS Standard Vertical Slant Panel Super Horizontal Slant Panel (4) (6) (12) (24) (25) (50) FEATURES Lid and Flange Measurement: 10.5 L x 8.5 W x D Body Measurement: 10.0 L x 18.0 W x 6.0 D Floor Cutout Size: 10.0 x 18.0 Cableway Slot: 3/8 x 16 All ACE Stage Pockets are compatible with interchangeable CONNECTRIX System Panels and isolated connector configurations. Designed to maximize space and allow adequate receptacle clearance, CONNECTRIX Panels house a larger number of connections than a standard ganged plate and allow for a customized configuration. When using PNL-140 Series Panels, Choose from CONNECTRIX Connector series: C C C C For more information on CONNECTRIX Panels see pg. 20 For more information on CONNECTRIX Connectors see pg. 19 CONNECTOR CAPACITY Up to (50) connections or (25) connections and (2) triple gang A/C Powder Coat Finishes: Special Order Lid & Bezel: Textured Black Decorator (BK) Antique Coppervein (CV) Solid Brass (BR) Stainless Steel (SS) x 50 OR x 25 x 12 COMPLETE SYSTEM INCLUDES Interchangeable Lids: Standard Lid (SL) Locking Lid (LL) Carpet Lid (CL) Modified Length Lid (ML) UL Listed: Panel Placement: Yes Horizontal Compatible ACE Panel Series: PNL-100 PNL-120 PNL-140 PSW-100 PE FP3E (1) Back Box Pocket Body with Horizontal Panel Brackets Installed (1) Interchangeable Lid & Trim Bezel (2) Hinge Pins and Springs (8) Installation Screws (1) Capture Slot Closure OPTIONS UL LISTED Locking Lid Enlarged Cable Exit Carpet Lid Extended Back Box UL Listed compliance Standard 514A file FLOOR BOX 44LK Suitable for raised floor applications pg ACE BACKSTAGE CO., INC Avenue Rockefeller Suite 200 Valencia, CA Tel: Fax:

11 PROUDLY MADE IN THE U.S.A. HORIZONTAL PANEL POCKET SUPER DOUBLE WIDE STAGE POCKET 10 TRIM BEZEL MOUNTING FLANGE AND LID ASSEMBLY LID (BLIND HINGE), SPRING LOADED PINS, AVAILABLE IN STANDARD FLUSH, STANDARD FLUSH LOCKING, OR RECESSED CARPET NOMINAL OPENING REMOVABLE SPRING LOADED HINGE PINS PERMIT EASY LID EXCHANGE FOR CARPET, LOCKING, AND STANDARD LID CONFIGURATIONS.937" LID STOP WITH RUBBER PAD, 2 PLACES " TOP VIEW (2) HINGED CABLE WAYSLOT CLOSURES 8.000" 11 GAUGE (.120" THICK) STEEL TRIM BEZEL MOUNTING FLANGE AND LID ASSEMBLY WITH POWDER COAT FINISH INSIDE AND OUTSIDE ANTIQUE COPPER VEIN TEXTURED BLACK BRUSHED BRASS* STAINLESS STEEL* *Solid Brass or Stainless Steel Metal *Finish Available as Special Order 6.000" SUPER DOUBLE WIDE STAGE POCKET BACK BOX #BRK104BBX 14 GAUGE SHEET STEEL CRS (.071" THICK) WITH A CLEAR ZINC FINISH 3.281" 2.375" RIGHT SIDE SECTION CONNECTRIX PANEL SYSTEM COMBINATION OF "#PNL-100", "#PNL-120", OR "#PNL-140" STAGE POCKET PANELS COMBINATION KNOCK-OUTS 1/2" AND 3/4", 1 PLACE TYPICAL ON OPPOSING SIDES 1.000" 5.000" ".375" CABLE WAYSLOT 1.250" TYPICAL TRIM BEZEL 10 TRIM BEZEL MOUNTING FLANGE AND LID ASSEMBLY.937" Download DWG & DXF AutoCAD, and PDF Spec Sheets for ALL ACE Stage Pockets at SUPER DOUBLE WIDE STAGE POCKET BACK BOX #BRK104BBX 14 GAUGE SHEET STEEL CRS (.071" THICK) WITH A CLEAR ZINC FINISH " FRONT SECTION CONNECTRIX PANEL SYSTEM COMBINATION OF "#PNL-100", "#PNL-120", OR "#PNL-140" STAGE POCKET PANELS SET THE SUPER STAGE POCKET BACK BOX #BRK104BBX SECURELY BRACED INTO THE FLOOR TO PROVIDE SUPPORT EQUAL TO THE FLOOR LOADING REQUIREMENTS, ACCOUNTING FOR ANY HEIGHT OFFSET REQUIRED FOR THE FINISHED FLOOR 6.000" COMBINATION KNOCK-OUTS 1/2", 3/4", AND 1-1/4", 2 PLACES TYPICAL ON OPPOSING SIDES 1.312" 1.312" " 1.312" " STANDARD POCKET PANELS FOR USE WITH 132XXXX SUPER PANEL HALF PANEL PNL-100 SERIES FULL PANEL PNL-120 SERIES ELECTRICAL PANEL PE SERIES PNL-140 SERIES SUPER STAGE POCKET MODEL NUMBERS MODEL # #134CLBK Black Super Double Wide Pocket w/ Carpet Lid #134CLCV Copper Vein Super Double Wide Pocket w/ Carpet Lid #134LLBK Black Super Double Wide Pocket w/ Lid Punched for Lock #134SLBK Black Super Double Wide Pocket w/ Standard Lid #134SLCV Copper Vein Super Double Wide Pocket w/ Standard Lid #234CLBR Brass Super Double Wide Pocket w/ Carpet Lid #234SLBR Brass Super Double Wide Pocket w/ Standard Lid #334CLSS Stainless Steel Super Double Wide Pocket w/ Carpet Lid #344SLSS Stainless Steel Super Double Wide Pocket w/ Standard Lid APPROVALS DATE FINISH DRAWN Electrostatic applied powdercoat CUSTOMER APPROVAL MATERIAL 11ga CRS - Lid & Flange 14ga CRS - Pocket Body ITEM 134XXXX Super floor pocket to house up to (50) connectors

12 HALF POCKET 123SLBK - HALF POCKET This medium-capacity ACE Pocket is the Half Stage Pocket. This vertical slant panel pocket is made of heavy gauge steel, and has been load tested to withstand momentary weight loads of more than 1000 lbs. Install this pocket in the floor surface for flush mounted, easy access to (6) CONNECTRIX Connectors or (1) single gang AC outlet. CONNECTRIX SYSTEM READY All ACE Stage Pockets are compatible with interchangeable CONNECTRIX System Panels and isolated connector configurations. Designed to maximize space and allow adequate receptacle clearance, CONNECTRIX Panels house a larger number of connections than a standard ganged plate and allow for a customized configuration. For more information on CONNECTRIX Panels see pg. 20 For more information on CONNECTRIX Connectors see pg. 19 ACE STAGE POCKETS Standard Vertical Slant Panel Super Horizontal Slant Panel CONNECTOR CAPACITY Up to (6) connections or (1) dual gang A/C x 6 OR x 2 (4) (6) (12) (24) (25) (50) Lid and Flange Measurement: Body Measurement: FEATURES L x 10.5 W x D L x W x 4.5 D PANEL OPTIONS Floor Cutout Size: 4.75 x 8.5 Cableway Slot: 3/8 x 4 Powder Coat Finishes: Special Order Lid & Bezel: Textured Black Decorator (BK) Antique Coppervein (CV) Solid Brass (BR) Stainless Steel (SS) Interchangeable Lids: Standard Lid (SL) Locking Lid (LL) Carpet Lid (CL) Modified Length Lid (ML) UL Listed: Panel Placement: Yes Vertical Compatible ACE Panel Series: PNL-100 PSW-100 PE #MP-100 PNL-100 PSW-100 #PE #PNL-120 INCLUDES (1) Vertical, Slant Panel Style, Stage Pocket (1) Interchangeable Lid (2) Hinge Pins and Spring Fasteners (8) Installation Screws (1) Capture Slot Closure OPTIONS #PNL-140 UL LISTED Locking Lid Enlarged Cable Exit Carpet Lid Back Access Cover Back Box UL Listed compliance Standard 514A file FLOOR BOX 44LK Suitable for raised floor applications pg. 16 pg ACE BACKSTAGE CO., INC Avenue Rockefeller Suite 200 Valencia, CA Tel: Fax:

13 FLOOR WHEN MOUNTING IN STAGE FLOOR WITHOUT ACE #103BBX BACK BOX PROUDLY MADE IN THE U.S.A. VERTICAL SLANT POCKET HALF.375" CABLE WAY SLOT 10 STAGE POCKET CAPTIVE SLOT CLOSURE DROPS INTO BOX WHEN NOMINAL CABLE WAY SLOT IS IN USE OPENING 6.875" 4.375" 11 GAUGE (.120" THICK) STEEL TRIM BEZEL AND LID ASSEMBLY WITH POWDER COAT FINISH INSIDE AND OUTSIDE ANTIQUE COPPER VEIN TEXTURED BLACK BRUSHED BRASS* STAINLESS STEEL* *Solid Brass or Stainless Steel Metal *Finish Available as Special Order Download DWG & DXF AutoCAD, and PDF Spec Sheets for ALL ACE Stage Pockets at CONNECTRIX A FLEXIBLE CONNECTOR AND PANEL SYSTEM Choose Pre-fabricated audio, communications, data, electric, video, and voice connectors and panels, or create custom panels as needed using the CONNECTRIX System of panels and connectors. OPEN ACCESS REMOVABLE HINGE PERMIT EASY LID EXCHANGE FOR CUSTOM LID CONFIGURATIONS TOP VIEW 4.75" x 8.5" CUTOUT IN STAGE FLOOR WHEN MOUNTING IN STAGE FLOOR WITHOUT ACE #103BBX BACK BOX " CABLE WAY SLOT 10 CAPTIVE SLOT CLOSURE DROPS INTO BOX WHEN CABLE WAY SLOT IS IN USE NOMINAL OPENING 6.000" 7/8" NOM. 1 NOMINAL SECTION VIEW 3.656" 8.000" 7.187" OPEN BACK ACCESS 1.875" NOM. 16 GAUGE (.060" THICK) WELDED STEEL POCKET BODY CONSTRUCTION CONNECTRIX A FLEXIBLE CONNECTOR AND PANEL SYSTEM Choose Pre-fabricated audio, communications, data, electric, video, and voice connectors and panels, or create custom panels as needed using the CONNECTRIX System of panels and connectors. REMOVABLE HINGE PINS PERMIT EASY LID EXCHANGE FOR CUSTOM LID CONFIGURATIONS " OPTIONAL BACK BOX WELDED 14 GAUGE (.071 THICK) STEEL 10 X 6.5 X 6 ZINC PLATED (ACE #103BBX BACK BOX) OR OPTIONAL BACK ACCESS COVER 14 GAUGE (.071 THICK) STEEL ZINC PLATED (ACE #23BAC BACK ACCESS COVER - NOT SHOWN) TRIM BEZEL 4 4 FRONT VIEW 6.000" SECTION VIEW OPEN BACK ACCESS 6.000" 7/8" NOM " NOM. 1 NOMINAL 3.656" 8.000" 7.187" 16 GAUGE (.060" THICK) WELDED STEEL POCKET BODY CONSTRUCTION 4.375" 4.625" " 6 OPTIONAL BACK BOX WELDED 14 GAUGE (.071 THICK) STEEL 10 X 6.5 X 6 ZINC PLATED (ACE #103BBX BACK BOX) OR OPTIONAL BACK ACCESS COVER 14 GAUGE (.071 THICK) STEEL HALF PANEL ZINC PLATED ELECTRICAL (ACE #23BAC PANEL BACK ACCESS COVER - NOT SHOWN) STANDARD POCKET PANELS FOR USE WITH 123XXXX TRIM BEZEL FRONT VIEW 6.000" PNL-100/PSW-100 SERIES PE SERIES MODEL # #123CLBK #123CLCV #123LLBK #123SLBK #123SLCV #223CLBR #223SLBR #323CLSS #323SLSS FULL POCKET MODEL NUMBERS Black Half Pocket w/ Carpet Lid Copper Vein Half Pocket w/ Carpet Lid Black Half Pocket w/ Lid Punched for Lock Black Half Pocket w/ Standard Lid Copper Vein Half Pocket w/ Standard Lid Brass Half Pocket w/ Carpet Lid Brass Half Pocket w/ Standard Lid Stainless Steel Half Pocket w/ Carpet Lid Stainless Steel Half Pocket w/ Standard Lid APPROVALS DATE FINISH DRAWN Electrostatic applied 4.375" powdercoat CUSTOMER APPROVAL 4.625" 6 MATERIAL 11ga CRS - Lid & Flange 16ga CRS - Pocket Body ITEM 123XXXX Half-sized floor pocket to house up to (6) connectors

14 MINI STAGE POCKET 025BK - MINI STAGE POCKET The Mini Stage Pocket is a rugged, high-density box with a compact footprint. Designed to conceal up to (4) CONNECTRIX connectors, the two panel positions in the pocket body utilize staggered MP series CONNECTRIX panels. Conceal AC power, audio, switches, etc under the floor surface with the flush mounted bezel and lid that are easily installed into raised floors with or without a back box. CONNECTRIX SYSTEM READY All ACE Stage Pockets are compatible with interchangeable CONNECTRIX System Panels and isolated connector configurations. Designed to maximize space and allow adequate receptacle clearance, CONNECTRIX Panels house a larger number of connections than a standard ganged plate and allow for a customized configuration. For more information on CONNECTRIX Panels see pg. 20 For more information on CONNECTRIX Connectors see pg. 19 ACE STAGE POCKETS Standard Vertical Slant Panel Super Horizontal Slant Panel CONNECTOR CAPACITY Up to (4) connections or (2) electrical outlets x 4 OR x 2 (4) (6) (12) (24) (25) (50) FEATURES PANEL OPTIONS Lid and Flange Measurement: Body Measurement: 4.75 L x 7.0 W x D L x W x D Floor Cutout Size: 2.88 x #MP-100 Cableway Slot: 3/8 x 1.25 (x2) PNL-100 PSW-100 #PE #PNL-120 #PNL-140 Powder Coat Finishes: Textured Black Decorator (BK) Antique Coppervein (CV) INCLUDES Special Order Lid & Bezel: Panel Placement: Solid Brass (BR) Stainless Steel (SS) Vertical (1) Vertical, Slant Panel Style, Stage Pocket (1) Lid & Trim Bezel (4) Installation Screws Compatible ACE Panel Series: MP Series OPTIONS DOWNLOAD SPEC SHEET Download DWG & DXF AutoCAD, and PDF Spec Sheets for ALL ACE Stage Pockets at Edison Snap-In Recepticle C Back Box with A/C Divider pg. 19 pg ACE BACKSTAGE CO., INC Avenue Rockefeller Suite 200 Valencia, CA Tel: Fax:

15 PROUDLY MADE IN THE U.S.A. VERTICAL SLANT POCKET MINI STAGE MINIPOCKET STAGE POCKET HEAVY DUTY STAINLESS STEEL HINGE AND RIVETS 3/8" x 1-1/4" CABLE EXIT SLOTS 2.750" 4.750" OPEN ACCESS 2.062" 5.350" 7.000" MAX LID OPENING 135¼ TRIM BEZEL LID ASSEMBLY 11 GA CRS (.120" THICK) NARROW CLEARANCE FOR SMALLER CONNECTORS CONNECTOR PANELS 2.062" WIDER CLEARANCE FOR LARGER CONNECTORS 2.245" OPTIONAL #025BBX BACK BOX 2.688" MINI STAGE POCKET BODY 16 GA CRS (.062" THICK) 3 OPTIONAL #025BBX BACK BOX 5.560" 3.750" STANDARD POCKET PANELS FOR USE WITH 025XX SUPER STAGE POCKET MODEL NUMBERS #MP-100 #MP-101 #MP-101L #MP-102 #MP-103 #MP-104 #MP-105 #MP-106 #MP-107 #MP-108 #MP-110 #MP-111 MODEL # #025BK #025CV #025BR #025SS Black Mini Pocket Copper Vein Mini Pocket Brass Mini Pocket Stainless Steel Mini Pocket #MP-112 #MP-113 #MP-114 #MP-115 APPROVALS DATE FINISH DRAWN Electrostatic applied powdercoat CUSTOMER APPROVAL MATERIAL 11ga CRS Lid & Bezel 16ga CRS Pocket Body ITEM 025XX Mini floor pocket to house up to (4) connectors

16 BACK ACCESS COVERS BACK ACCESS COVER ACE Back Access Covers are a simple, cost effective option in the sequence of installation in raised floor applications. During the rough-in stage, the BAC may be connected to the conduit through combination knock-outs and left temporarily tacked to the floor joist where the pocket will be installed. All wire can be pulled, and low voltage terminations to connectors/panels can be completed before the finish stage of construction. Accepts accessory brackets for isolation of high and low voltage. #23BAC Back Access Cover for Half Stage Pockets #22BAC Back Access Cover for Full Stage Pockets MATERIAL SPEC MATERIAL: 14 Gauge Sheet Steel CRS (.071 Thick) FINISH: Clear Zinc, Mil Spec ASTM-B633 Type 1, Class 1 FABRICATION: Precision die formed UL LISTED UL Listed compliance Standard 514A in combination with inner floor pocket file FLOOR BOX 44LK #ISO24BAC Isolated Back Access Cover for Double Wide Stage Pockets #22BAC Full Pocket Back Access Cover installation is completed quickly & easily in 3 steps BACK BOXES HALF SIZE BACK BOX MINI SIZE BACK BOX #103BBX #025BBX #103BBXW #025BBX/AC HALF SIZE BACK BOX MINI SIZE BACK BOX Half Size Back Boxes are 14 gauge steel with a protective lid that is discarded when the pocket is fully installed. Clear zinc coated, they mate using a pre-drilled mounting flange and have multiple combination knock-outs. Model #103BBX is UL Compliance Listed. ZINC COAT #103BBX MODEL NUMBERS POLYURETHANE JACKET #103BBXW This three gang welded steel box mates perfectly with the ACE Mini Pocket and can be used to isolate AC power and Audio connectivity when ordered as the #025BBX/AC. Model #025BBX is UL Compliance Listed. MODEL NUMBERS ZINC COAT #025BBX ISO #025BBX/AC Standard Vertical Slant Panel COMPATIBLE WITH: Super Horizontal Slant Panel Standard Vertical Slant Panel COMPATIBLE WITH: Super Horizontal Slant Panel (4) (6) (12) (24) (25) (50) (4) (6) (12) (24) (25) (50) 16 ACE BACKSTAGE CO., INC Avenue Rockefeller Suite 200 Valencia, CA Tel: Fax:

17 BACK BOXES FULL SIZE BACKBOX DOUBLE WIDE SIZE BACKBOX #102BBX #104BBX #ISO102BBX #102BBXW #ISO104BBX #104BBXW Finished in clear zinc for corrosion resistance, these welded steel back boxes mate with standard ACE Stage Pockets using a pre-drilled mounting flange. Available in four different depths, ACE Back Boxes provide 1.5, 3.5, 4.5 and 7.5 work clearance underneath the installed stage pocket. Multiple combination knock-outs make these boxes ideal for feed thru or distribution junctions. Models #102BBX and #104BBX are UL Compliance Listed. Polyurethane Encapsulated Back Boxes provide a 1/16 watertight jacket to seal seams, holes, and knock-outs - effectively forming a airtight shield. These boxes provide protection against incursion of moisture, abrasion, chemicals, impact and harsh climates. Back boxes with isolation brackets (ISOXXXBBX) provide galvaneal steel separation between high and low voltage in ACE Stage Pockets. MODEL NUMBERS DEPTH ZINC COAT ISO POLYURETHANE JACKET 6 #102BBX #ISO102BBX #102BBXW 8 #1028BBX #ISO1028BBX #1028BBXW 12 #102DDBBX #ISO102DDBBX #102DDBBXW MODEL NUMBERS DEPTH ZINC COAT ISO POLYURETHANE JACKET 6 #104BBX #ISO104BBX #104BBXW 8 #1048BBX #ISO1048BBX #1048BBXW 12 #104DDBBX #ISO104DDBBX #104DDBBXW Standard Vertical Slant Panel COMPATIBLE WITH: Super Horizontal Slant Panel Standard Vertical Slant Panel COMPATIBLE WITH: Super Horizontal Slant Panel (4) (6) (12) (24) (25) (50) (4) (6) (12) (24) (25) (50) PROTECTIVE LID - DISCARD WHEN INSTALLING POCKET ACE Back Boxes ship with a removable lid (1) to provide protection for the inside of the back box during installation. Once installation of floor is complete, the lid is removed and discarded (2), leaving the inside free of any dirt or concrete and allowing an easy install of the stage pocket (3) ACE BACKSTAGE CO., INC Avenue Rockefeller Suite 200 Valencia, CA Tel: Fax:

18 BRACKET KIT ASSEMBLIES BRACKET KIT ASSEMBLIES (#BRK) ACE Bracket Kit Assemblies #BRK102 (A1) and #BRK104 (B1) may be installed in Standard Full Pocket Back Boxes (A2) and Double Wide Pocket Back Boxes (B2). Once Bracket Kit Assemblies have been installed in their respective Back Boxes (A3) and (B3), the resulting products (with #BZ132SLBK and #BZ134SLBK Trim Bezel-Lid Assemblies also added) are the Super Pockets (A4) and Super Double Wide Pockets (B4). #BRK102 #102BBX #BRK102BBX #132SLBK A1 A2 A3 A4 #BRK104 #104BBX #BRK104BBX #134SLBK STAGE POCKET OPTIONS B1 B2 B3 B4 LOCKING LID OPTIONS A B C Three different types of keyed locks with trim bezels are available for ACE Vertical Slant and Horizontal Panel Pockets (Note: No Locking Lid for Carpet or Mini Pocket): A) Standard Flat Head Screwdriver Lock (screwdriver not included). B) Standard 5/32 Allen Key Wrench (key included). C) Tubular Butterfly Key Lock (key included). INCREASED CABLE EXIT SIZE OPTION Slot Opening Slot Opening 1 Slot Opening Installations requiring exaggerated gauge cables can be accommodated. ACE offers three specialty lid lengths to customize the cable exit space. Each modified lid is supplied with a c-slot closure to be used when the pocket has no cables exiting. A) Modified Lid with 1/2 Slot Opening. B) Modified Lid with 3/4 Slot Opening. C) Modified Lid with 1 Slot Opening. *Standard Cable Exit has a 3/8 Slot Opening INTERCHANGEABLE LIDS Standard Flush Mount Lid Recessed Lid for Carpet Installation Choose from standard flush mount lid or recessed lid for carpet installation. Lids are easily changeable. ELECTRICAL A/C ELECTRIC ISOLATION KIT A B C D ELECTRICAL PANELS WITH SWITCHBOX #PE Single Gang Panel for use with all vertical panel style pockets and Super Double Wide Pockets #PE-MP ELECTRICAL PANEL #PE-MP Single Gang Panel for use with pockets installed into ISO Back Boxes and Back Access Covers Top view of an #A/C ISO KIT installed in a #102BBX Back Box without (1) and with (2) the Full Stage Pocket Body. 1 2 #FP3E Triple Gang Panel for use with all vertical panel style pockets and Super Double Wide Pockets For use when installing Isolated Back Boxes or Isolated Back Access Covers, the PE-MP Electrical Panel Mount eliminates the switchbox included with the other electrical panels and opens up a larger work area for receptacle termination, while maintaining high and low voltage separation. #ISO24BAC Isolated Back Access Cover *SHOWN INSTALLED WITH PE PANEL #A/C ISO KIT - 1/2 Conduit A.C. Electrical Isolation Kit Includes: A - (1) #RACO Non-Metallic Extra-Flex Conduit B - (1) #RACO º Swivel Connector C - (1) #RACO Straight Connector D - (1) #GRC COUPLING...Coupling, Female-to-Female #WP-PE Single Gang Panel for use with Table Top Pockets (145xxxx) *SHOWN WITH RECEPTACLES INSTALLED #ISO102BBX Isolated Back Box 18 ACE BACKSTAGE CO., INC Avenue Rockefeller Suite 200 Valencia, CA Tel: Fax:

19 CONNECTRIX CONNECTORS CONNECTRIX Connectors eliminate the need for a custom cut panel, utilizing our modular system that seamlessly mates each connector into pre-cut holes in CONNECTRIX Panels. Using this system, ACE can ship pocket, wall, or rack panels immediately. No need to wait for a custom cut panel. The CONNECTRIX library offers a wide selection of isolated, adaptor-mounted connectors. CONNECTRIX Connectors arrive installed, per your instruction with either black pop rivets or screws, ready to terminate. XLR 9-PIN 3-Pin Female #C Solder #C Gold #C Screw Term 3-Pin Female #C Pin Female #C Pin Female #C Pin Female #C Pin Female 9-Pin Female #C Solder #C Feed Through #C Screw Term #C Feed Through* #C Solder* #C Screw Term* 9-Pin Male #C Solder #C Solder 9-Pin Male #C Feed Through #C Feed Through* 15-PIN / 25-PIN 3-Pin Male #C Nylon #C Metal #C Gold #C Screw Term VIDEO 4-Pin Male #C Pin Male #C Pin Male #C RCA/BNC XLR Combo 1/4 #C Pin Female #C Feed Through #C Solder #C Solder* 15-Pin Female #C Solder #C Solder* 15-Pin Female 15-Pin Male #C Screw Term #C Feed Through #C Feed Through* S-Video #C S-Video Value Priced #C HD 15 #C Left & Right RCA #C Feed Through RCA #C Feed Through RCA Value Priced #C HD 15 #C HD 15 - Value Priced #C mm Combo HD15 #C Pin Female #C Feed Through #C Solder #C Feed Through* #C Solder* COMPUTER 1/4 HD 15 - Value Priced #C Feed Through HDMI #C RCA to BNC #C Recessed RCA to BNC #C BNC #C HDMI - Value Priced #C DVI #C Recessed BNC #C Feed Through BNC #C Feed Through BNC Value Priced #C USB to USB #C USB to USB - Value Priced #C /4 Stereo #C /4 #C Stereo #C Mono 1/8 Combo XLR and 1/4 #C RJ45 FireWire #C FireWire - Value Priced #C RJ45 Cat 5 Punchdown #C RJ45 Cat 5 Punchdown #C RJ45 Cat 5 Feed Through #C RJ45 Cat 6 Value Priced #C RJ45 Cat 5 Value Priced #C RJ45 Cat 6 Feed Through #C RGBHV (5) BNC #C Solder #C Feed Through RCA #C Black #C Red #C Yellow #C White RCA - Feed Through #C Red #C White #C Yellow #C Green #C Blue HD 15 #C MISC HD 15 - Value Priced #C Isolated 3.5mm #C Isolated 3.5mm Value Priced #C mm Combo HD15 #C POWER Isolated 1/8 #C CATV FIBER OPTICS RJ11 - Feed Through #C MIDI #C AMP #C AMP #C AMP #C CATV #C Solder #C Feed Through CATV Value Priced #C Fiber Optic #C opticalcon #C speakon #C Locking #C Screw Term * - Only compatible with PNL-140 Series - Only compatible with MP-100 Series ACE BACKSTAGE CO., INC Avenue Rockefeller Suite 200 Valencia, CA Tel: Fax:

20 CONNECTRIX STAGE POCKET PANELS Used with CONNECTRIX Connectors, these high strength aluminum panels are designed to allow perfect connector clearance and the maximum number of connections in every panel. Because they are machined aluminum alloy (6061-T6) and not punched, they stay flat and undistorted, and are stronger than mild steel panels. The CONNECTRIX style cutout makes it possible to mount any combination of jacks (RJ45, RJ11, multipins, BNC s, speaker jacks) without a single custom punch. CONNECTRIX POCKET PANELS Not Compatible With C or C Series Connectors MINI POCKET PANELS Not Compatible With C Series Connectors #PNL-100 #PNL-102 #PNL-103 #MP-100 Blank #MP-101 CONNECTRIX Centered #MP-101L CONNECTRIX (L or R) #MP-102 CONNECTRIX #MP-103 CONNECTRIX/S-Video #MP-104 CONNECTRIX/ICC #MP-105 Backloaded #MP-106 Backloaded/ICC #PNL-104 #PNL-105 #PNL-106 #MP-107 Backloaded/ 1/ 8 or 1/ 4 #MP-108 Backloaded #MP-110 ICC Centered #MP-111 (L or R) #PNL-120 #PNL-124 #MP-112 MAAP Module #MP-113 A/C Centered #MP-114 A/C (L or R) #MP Pin #PNL-126 #PNL-128 Standard Vertical Slant Panel COMPATIBLE WITH: Super Horizontal Slant Panel (4) (6) (12) (24) (25) (50) #PNL-1210 #PNL-1212 SUPER POCKET PANELS Compatible With C Series Connectors Compatible with C-15000, C and C Series Connectors #PSW-100 #PSW-102 #PSW-103 #PSW-104 #PSW-105 #PSW-106 #PNL-140 #PNL-1425 Standard Vertical Slant Panel COMPATIBLE WITH: Super Horizontal Slant Panel Standard Vertical Slant Panel COMPATIBLE WITH: Super Horizontal Slant Panel (4) (6) (12) (24) (25) (50) (4) (6) (12) (24) (25) (50) 20 ACE BACKSTAGE CO., INC Avenue Rockefeller Suite 200 Valencia, CA Tel: Fax:

21 CUSTOMIZED CONNECTRIX PANELS CUSTOM ENGRAVING Rotary engraving on stock CONNECTRIX Panels or CUSTOM Fabricated Panels is fast and easily accomplished on a separate dedicated CNC routing machine. The finished panels show bright aluminum in the engraved characters and do not need to be back filled. CONNECTRIX Panels are always in stock, can be engraved with company logo information, and ship quickly. Many times ACE ships engraved panels in less than 5 days. CUSTOM FABRICATION Computer Assisted Drafting (CAD) systems feed data to our precision CNC rotary cutting machines to define your panels accurately. Panels are cut and powder-coated, then return to the table for engraving. The finished panels show bright aluminum in the engraved characters and do not need to be back filled. Custom Fabricated Panels can be created in sizes as large as 48 x 36 in 1/8 and 1/16 thickness. Each panel is computer drawn and approved by you before being cut, coated, and engraved. Then the coated panel is sent to the assembly bench and populated with specified connectors, switches, nutserts, etc. Once completed the panel is inspected and checked twice before packaging for shipment. For Custom Panel Engraving Forms, Visit acebackstage.com/abc_pages/custom_panels.html CONNECTRIX WALL & RACK PANELS #WP-PE #WP-100 #WP-200 #WP-300 #WP-400 #WP-600 #WP-101 #WP-204 #WP-306 #WP-408 #WP-6012 #WP-102 #WP-206 #WP-308 #WP-4012 #WP-6016 #RPL-110 #RPL-100 #RPL-230 #RPL-200 #RPL-345 #RPL-300 ACE BACKSTAGE CO., INC Avenue Rockefeller Suite 200 Valencia, CA Tel: Fax:

22 TABLE TOP POCKETS 145SLBK - TABLE TOP POCKET 146SLBK - CONFERENCE POCKET Absolutely rugged and reliable for day-to-day use, the Table Top Pocket looks great in any boardroom or presentation room setting. Designed specifically for the table, the lid stays open at 3 different intervals allowing you to keep a minimum height profile when in use. Easy to install and secure with reversible installation brackets, this pocket has a unique panel mounting system that allows for 1&2 gang panels or ACE PNL-100/120 CONNECTRIX series panels. This tabletop pocket provides convenient access to A/V and network cables as they pull through to slide in and out of the storage well. As plugs are needed, the low profile lid slides into the pocket out of sight, or can rest flush to the table with cables exiting through the flange slot. The Conference Port is easily installed without the need for intricate routing because the machine-rounded, beveled flange sits virtually flush on your tabletop surface. 11ga. (.120" thick) Steel, Brass or Stainless Steel Trim Bezel and Lid Lid and Flange Measurement: Body Measurement: L x 8.0 W x D 9.0 L x W x 2.0 D Table Cutout Size: x 6.75 Powder Coat Finishes: Textured Black Decorator (BK) Special Order Lid & Bezel: Solid Brass (BR) Stainless Steel (SS) Panel Placement: " FEATURES Horizontal Compatible ACE Panels Series PNL-100 PE WP-100 PNL-120 FP2E WP-200 WP-PE TOP VIEW 8.0" Lid and Flange Measurement: Body Measurement: Table Cutout Size: Cableway Slot: Powder Coat Finishes: Special Order Lid & Bezel: FEATURES L x W x D 4.0 L x 4.5 W x 3.95 D L x W L x W Textured Black Decorator (BK) Solid Brass (BR) Stainless Steel (SS) TABLE TOP POCKET MODEL NUMBERS MODEL # #145SLBK Black Table Top Pocket w/ Standard Lid #245SLBR Brass Table Top Pocket w/ Standard Lid #345SLSS Stainless Steel Table Top Pocket w/ Standard Lid CONFERENCE POCKET MODEL NUMBERS MODEL # #146SLBK Black Conference Port w/ Standard Lid #246SLBR Brass Conference Port w/ Standard Lid #346SLSS Stainless Steel Conference Port w/ Standard Lid " 1ga. (.120" thick) Steel, Brass or Stainless Steel rim Bezel and Lid TOP VIEW 8.0" 8.00" 2.183" 5.563" 9.00" " 22 SIDE VIEW Lid Locks open to ACE BACKSTAGE provide a cable CO., exit INC Avenue Rockefeller Suite 200 Valencia, CA Tel: Fax: and a minimum height profile when in use 2.844"

23 STAGE MANAGEMENT PRODUCTS This versatile microphone offers the performance of overhead hanging microphones in a totally portable configuration, and is the only WIRELESS microphone of its type in its price range. Manufactured by ACE in partnership with Audio-Technica and Shure to provide solid performance of each Audio-Technica or Shure branded condenser microphone, They are available only at ACE Backstage. CSMs are available in one of two lengths (40 /60 ), and with your choice of one interchangeable Audio-Technica or Shure element, ranging from a tight 90* polar pattern to 360* of pick up. Designed with a small diameter gooseneck to permit flexible positioning, all CSMs easily mount onto any standard microphone stand. They will not become unbalanced or tip over even when fully extended. CHOIR STICK MICROPHONE CSM Spec Sheet #CSM-60CW Choir Stick Mics CSM-40/CSM-60 Wireless CSM-40W/CSM-60W CSM Spec Sheet Choir Stick Mics CSM-41/CSM-61 Wireless CSM-41W/CSM-61W Use your smartphone to view Audio-Technica and Shure CSM Spec Sheets or visit acebackstage.com/csm MICROPHONE SOFTPOD This simple yet sturdy device was designed to thread on any standard microphone stand and has been updated to accommodate all types of wireless or handheld microphones. The Microphone Softpod is easy to use and is lightweight, which makes it portable and efficient. The soft foam isolates and cushions microphones from each other and minimizes noise when placing or removing microphones. The SoftpodÕ s small footprint and lightweight design make it great for small locations or portable systems. 7 Mic Softpod Noise Isolating Foam 8 Holds up to (6) Microphones #43 MICROPHONE HANGER SLUG The ACE Microphone Hanger Slug allows you to hang almost any microphone from a cable end and point it in any direction. The Microphone Hanger Slug permits a standard microphone stand mount clip to be attached near the end of a hanging cable and the microphone to be clipped in place. The cable is clamped to the slug with a cable tie allowing the cable above to come to a normal relaxed position. This permits the adjustment of the microphone side-to-side movements (yaw) by turning the microphone clip on the slug without twisting the cable above the slug... the microphone will stay exactly where it is pointed. 1. Screw the Slug into the mic clip. 2. #43 Slug threads are pliable, allowing the slug to grip and lock into the clip. 3. Secure the mic cable to slug with the provided cable tie 4. Allow the cable above the slug to twist to a set position 5. Adjust mic clip on slug to point the mic to the correct direction without twisting hanging cable 6. Pivot the clip up/down to position Compatible with most microphone stand mount clips ACE BACKSTAGE CO., INC Avenue Rockefeller Suite 200 Valencia, CA Tel: Fax:

24 PUSH PUSH ACE BACKSTAGE CO., INC Avenue Rockefeller Suite 200 Valencia, CA Presorted Standard U.S. Postage PAID Los Angeles, CA Permit No ACE BACKSTAGE CO. CLEAR COM DMX12 ACE BACKSTAGE CO., INC. STAGE POCKET SYSTEMS Stage Pocket Systems / Panel Fabrication / Spec Fabrication / Stage Management Products CUSTOM DESIGNED CONNECTIVITY ACE can develop custom pockets by utilizing our library of standard components and pocket bodies to design and create pockets that will fit your specific application. Or you can have ACE create a custom pocket from the ground up to meet your specified requirements. From conceptual planning to creation, ACE can build you a custom pocket that will meet all your design expectations. Customize ACE Pockets & Panels to YOUR Needs Download a QR Code Reader on your smartphone to view more ACE Custom Products EXTENDED BEZEL FLOOR BOX CUSTOM BRACKETS & LID FOR OVERSIZED COMPONENTS HEAVY LOAD CAPACITY NO MINIMUM ORDER QUICK PRODUCTION DESIGN ASSISTANCE CAD PRODUCTION DRAWING PROVIDED