0.5 mm Pitch, 1.2 mm above the board, Flexible Printed Circuit & Flexible Flat Cable ZIF Connectors

Transcription

1 All non-rohs products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website RoHS search at or contact your Hirose sales representative..5 mm Pitch, 1.2 mm above the board, Flexible Printed Circuit & Flexible Flat Cable ZIF Connectors FH Series Increased FPC retention force Small size 1.2mm 2.5mm [ pos. ] 17mm Metal fittings (Leadless) Features 1. Low-profile, small PCB mounting area Narrow width of only 2.5 mm reduced the board footprint by approximately 17% to 57%, as compared to several similar FH Series HRS connectors. 2. Increased FPC/FFC retention force _ In the horizontal direction: Approximately 2. times (compared to similar FH Series HRS connectors) _ In the vertical direction: Approximately 1.7 times (compared to similar FH Series HRS connectors). Conductive traces on the PCB can run under the connector No exposed contacts on the bottom of the connector. 4. One finger operation of the actuator Proven (in several other Hirose s connectors) Flip-Lock rotating actuator assures reliable mechanical and electrical connection with FPC/FFC, confirming it with a definite tactile feel. 5. Easy FPC/FFC insertion FPC/FFC is self-guided in the connector assuring correct and reliable electrical and mechanical connection. 6. Accepts. mm thick FPC, FFC Increased rigidity. mm thick FPC / FFC is reliably inserted and terminated. 7. Board placement with automatic equipment Flat top surface and packaging on the tape-and-reel allows use of vacuum nozzles. Standard reel contains 5, connectors. Can be mounted over conductive traces. No exposed contacts on the bottom of the connector Simple operation 1 Open the actuator 2 Insert FPC FPC Locked condition Close the actuator 4 FPC connected 2 1 Actuator Applications Notebook computers, digital cameras, LCD connections, plasma displays, Digital Video Cameras, Portable Digital Assistants and other compact devices requiring Flexible Printed Circuit Connections using high reliability ZIF connectors

2 All non-rohs FH products Series.5 have been discontinued, mm Pitch, or will 1.2 be discontinued mm above soon. the Please board, check the Flexible products Printed status on the Circuit Hirose website & Flexible RoHS search Flat at Cable ZIF Connectors or contact your Hirose sales representative. Product Specifications Ratings Current rating Voltage rating.5 A 5 V AC Operating temperature range -55 ç to +85ç (Note 1) Operating humidity range Relative humidity 9% max. (No condensation) Storage temperature range -1ç to +5ç (Note 2) Storage humidity range Relative humidity 9% max. (No condensation) Recommended FPC Thickness =. ±.5mm gold plated (under pos.),. ±.mm gold plated (over 1 pos.) Item Specification Conditions 1. Insulation resistance 2. Withstanding voltage 5 Mø min. No flashover or insulation breakdown. 1 V DC 15 V AC /one minute. Contact resistance 5 mø max. * Including FPC conductor resistance 1 ma 4. Durability Contact resistance: 5 mø max. (insertion/ withdrawal) No damage, cracks, or parts dislocation. 2 cycles 5. Vibration 6. Shock No electrical discontinuity of 1μs or more. Contact resistance: 5 mø max. No damage, cracks, or parts dislocation. Frequency: 1 to 55 Hz, single amplitude of.75 mm, 1 cycles in each of the directions. Acceleration of 981 m/s 2, 6 ms duration, sine half-wave waveform, cycles in each of the axis 7. Humidity (Steady state) 8. Temperature cycle 9. Resistance to soldering heat Contact resistance: 5 mø max. Insulation resistance: 5 Mø min. No damage, cracks, or parts dislocation. No deformation of components affecting performance. 96 hours at 4ç and humidity of 9% to 95%. Temperature : -55ç/+15ç to +5ç/+85ç/+15ç to +5ç Time : / 2 to / / 2 to (Minutes) 5 cycles Reflow : At the recommended temperature profile Manual soldering: 5ç ± 1ç for 5 seconds Note 1: Includes temperature rise caused by current flow. Note 2: The term storage refers to products stored for long period of time prior to mounting and use. Operating Temperature Range and Humidity range covers non- conducting condition of installed connectors in storage, shipment or during transportation. Materials Part Insulator Actuator Contacts Metal fittings Material Finish Remarks Color : Beige Polyamide Color : Dark brown UL94V- Phosphor bronze Gold flash plated --- Pure tin reflow plated --- Ordering information FH - 28S -.5 SH (1) Series name: FH 2 No. of contacts Number of contacts: 6, 9, 1, 12, 14, 19, 2, 26, 28,, 2, 6, 4, 45 Contact pitch:.5 mm 4 Termination type SH : SMT horizontal 5 Blank : Gold flash plated (RoSH compliant) (1) : Nickel barrier gold flash plated (RoHS compliant) 2

3 All non-rohs products have been discontinued, or FH will be Series.5 discontinued soon. mm Please Pitch, check 1.2 the products mm above status on the the board, Hirose website Flexible RoHS search Printed at Circuit & Flexible Flat or contact Cable your ZIF Hirose Connectors sales representative. Connector Dimensions A±.15 Lot No. indicator.5 B Number of contacts (.15).15 G G 2.±.15 (1) A** Polarizing mark indicator (.45) Number of contacts indicator (C: FPC insertion slot dimension) (.15) F D±.1 F (12 ) (1.8) 1 2.5±.1 a.15max.55±.1 (1.1) 1.7±.2 2.2±.15.5± ±.1.±.1.15MAX 1 2 Notes The coplanarity of each terminal lead is within.1 max. The contact terminal lead position indicates the dimension from the bottom a surface of the insulator body. Difference of each terminal lead is within.1 max. Slight variations in color of the plastic compounds do not affect form, fit or function of the connector. Unit: mm Part Number CL No. Number of Contacts A B C D RoHS FH-6S-.5SH (**) FH-9S-.5SH (**) FH-1S-.5SH (**) FH-12S-.5SH (**) FH-14S-.5SH (**) FH-19S-.5SH (**) FH-2S-.5SH (**) FH-26S-.5SH (**) FH-28S-.5SH (**) FH-S-.5SH (**) FH-2S-.5SH (**) FH-6S-.5SH (**) FH-4S-.5SH (**) FH-45S-.5SH (**) ** ** ** ** ** ** ** ** ** ** ** ** ** ** YES (Note 1) Note 1: (**) : Plating specification. Refer to ordering information. Note 2: Tape-and-reel packaging (5, pieces/reel). Order by number of reels.

4 All non-rohs FH products Series.5 have been discontinued, mm Pitch, or will 1.2 be discontinued mm above soon. the Please board, check the Flexible products Printed status on the Circuit Hirose website & Flexible RoHS search Flat at Cable ZIF Connectors or contact your Hirose sales representative. BRecommended PCB mounting pattern and metal mask dimensions.65±.5.5 B Number of contacts.±.5(land).1 H.±.5(Metal mask) H (.2).8±.5 2.8±.5 (.15) (2.15) (2.45) J±.1 K±.1 (.2) (.2) (.15) (A) BRecommended FPC dimensions L±.5.5±.7 B±..5±..5±.(FPC).±.(FFC) 2-R.2 <under pos.>.±.5 <over 1 pos.>.±. E 2.±.(Exposed area).min(stiffener) Note 1: Polyimide and a thermally hardened adhesive is recommended as the materials for the stiffener. Note 2: If the stiffener is less than. mm, E dimension must be.5 mm min. Part Number FH-6S-.5SH (**) FH-9S-.5SH (**) FH-1S-.5SH (**) FH-12S-.5SH (**) FH-14S-.5SH (**) FH-19S-.5SH (**) FH-2S-.5SH (**) FH-26S-.5SH (**) FH-28S-.5SH (**) FH-S-.5SH (**) FH-2S-.5SH (**) FH-6S-.5SH (**) FH-4S-.5SH (**) FH-45S-.5SH (**) Unit: mm CL No. Number of Contacts A B J K L ** ** ** ** ** ** ** ** ** ** ** ** ** **

5 All non-rohs products have been discontinued, or FH will be Series.5 discontinued soon. mm Please Pitch, check 1.2 the products mm above status on the the board, Hirose website Flexible RoHS search Printed at Circuit & Flexible Flat or contact Cable your ZIF Hirose Connectors sales representative. BPackaging Specifications Embossed Carrier Tape Dimensions (Tape width up to 24mm) (1.7) 4±.1 2±.15 (.) 8±.1 Ø (Q) N±.1 M±. 1.75±.1 () (.8) (1) Flat surface for placement with automatic equipment Unreeling direction Embossed Carrier Tape Dimensions (Tape width 2mm and over) (1.7) 4±.1 2±.15 (.) 8±.1 Ø (Q) N±.1 P± ±.1 M±. Unreeling direction () (.8) (1) Flat surface for placement with automatic equipment Unit: mm Part Number FH-6S-.5SH (**) FH-9S-.5SH (**) FH-1S-.5SH (**) FH-12S-.5SH (**) FH-14S-.5SH (**) FH-19S-.5SH (**) FH-2S-.5SH (**) FH-26S-.5SH (**) FH-28S-.5SH (**) FH-S-.5SH (**) FH-2S-.5SH (**) FH-6S-.5SH (**) FH-4S-.5SH (**) FH-45S-.5SH (**) CL No. Number of Contacts M N P Q ** ** ** ** ** ** ** ** ** ** ** ** ** ** R S

6 All non-rohs FH products Series.5 have been discontinued, mm Pitch, or will 1.2 be discontinued mm above soon. the Please board, check the Flexible products Printed status on the Circuit Hirose website & Flexible RoHS search Flat at Cable ZIF Connectors or contact your Hirose sales representative. Reel Dimensions (Ø1) (R:INSIDE) (Ø8) (Ø8) (S:OUTSIDE) End section Mounting section Lead section (4 mm min.) Blank section (1 pockets min.) Embossed carrier tape Blank section (1 pockets min.) Top cover tape Note: 5, pieces per reel. Embossed tape 2 mm or wider will have perforated feed holes on two sides. 6

7 All non-rohs products have been discontinued, or FH will be Series.5 discontinued soon. mm Please Pitch, check 1.2 the products mm above status on the the board, Hirose website Flexible RoHS search Printed at Circuit & Flexible Flat or contact Cable your ZIF Hirose Connectors sales representative. BRecommended Temperature Profile Using Lead-free Solder paste Temperature (ç) ç 2ç MAX ç 2ç HRS test conditions Solder method : Reflow, IR/hot air (Nihon Den-netsu Co., Ltd. s Part Number: SENSBY NR-2) Environment : Room air Solder composition : Paste, 96.5%Sn/.%Ag/.5%Cu (Senju Metal Industry, Co., Ltd. s Part Number: M75-GRN6-K2-V) Test board : Glass epoxy mm 5mm.8mm thick Land dimensions : Contacts lead.mm.65mm Metal fittings.55mm.8mm Metal mask : Contacts lead.mm.65mm.1mm thick Metal fittings.55mm.8mm.1mm thick 5 Start ç (6 sec.) 9 to 12 sec. Preheating (6 sec.) Sodering This temperature profile is based on the above conditions. In individual applications the actual temperature may vary, depending on solder paste type, volume/thickness and board size/thickness. Consult your solder paste and equipment manufacturer for specific recommendations. Time (Seconds) 7

8 All non-rohs FH products Series.5 have been discontinued, mm Pitch, or will 1.2 be discontinued mm above soon. the Please board, check the Flexible products Printed status on the Circuit Hirose website & Flexible RoHS search Flat at Cable ZIF Connectors or contact your Hirose sales representative. BFH Series FPC/FFC Construction (Recommended Specifications) 1. Using Single-sided FPC Material Name Covering film layer Cover adhesive Surface treatment Copper foil Base adhesive Base film Reinforcement material adhesive Stiffener Material Polyimide 1 mil thick Nickel under plated 1 to 5μm / Gold plated.2μm Cu 1oz Polyimide 1 mil thick Heat-hardened adhesive Polyimide 7 mil thick Total Thickness (μm) Using Double-sided FPC Material Name Covering film layer Cover adhesive Surface treatment Through-hole copper Copper foil Base adhesive Base film Base adhesive Copper foil Cover adhesive Covering film layer Reinforcement material adhesive Stiffener Material Polyimide 1 mil thick Nickel under plated 1 to 5μm / Gold plated.2μm Cu Cu 1/2oz Polyimide 1 mil thick Cu 1/2oz Polyimide 1 mil thick Heat-hardened adhesive Polyimide 4 mil thick Total Thickness (μm) Using FFC Material Name Material Thickness (μm) Polyester film 12 Adhesive polyester thermoplastic type Gold plated, soft copper film 5 Adhesive Polyester Polyester 12 Adhesive Polyester Stiffener Polyester 188 Total 295 π Practical tolerance of thickness dimension is ±2 μm To prevent release of the FPC due to it's bending, use of double sided FPC with copper foil on the back side is NOT RECOMMENDED. 8

9 All non-rohs products have been discontinued, or FH will be Series.5 discontinued soon. mm Please Pitch, check 1.2 the products mm above status on the the board, Hirose website Flexible RoHS search Printed at Circuit & Flexible Flat or contact Cable your ZIF Hirose Connectors sales representative. BOperation and Precautions Operation 1.FPC insertion procedure. Connector installed on the board. 1 Lift up the actuator. Use thumb or index finger. 2 Fully insert the FPC in the connector parallel to mounting surface, with the exposed conductive traces facing down. FPC conductor surface (Bottom side) Rotate down the actuator until firmly closed. It is critical that the inserted FPC is not moved and remains fully inserted. 2.FPC removal 1 Lift up the actuator. Carefully withdraw the FPC. 9

10 All non-rohs FH products Series.5 have been discontinued, mm Pitch, or will 1.2 be discontinued mm above soon. the Please board, check the Flexible products Printed status on the Circuit Hirose website & Flexible RoHS search Flat at Cable ZIF Connectors or contact your Hirose sales representative. Precautions Exercise care when handling connectors. Follow recommendations given below. PC board flexing SPC board connector mounting area The connectors are straight within.1 mm max. Make sure that the PC board connector mounting area flatness can accept the connector terminals without causing any failure of the solder joints. SHandling before mounting on PCB Insertion of the FPC or operation of the actuator prior to mounting on the PCB is NOT RECOMMENDED. SPC Board handling Exercise caution when handling boards with the connectors installed. Do not apply any forces affecting soldered joints. Connector PCB Precautions When Inserting or Removing FPC Pay attention to the following points when inserting FPC. SActuator operation 1 Do not apply excessive force when opening the actuator prior to FPC insertion. When opening make sure that the force is applied only to the actuator itself, avoiding touching of the contacts. Damege to the contacts Damage to the contacts 2 Axis of rotation (12 ) Axis of rotation Assure free rotation of the actuator The actuator will rotate 12 degrees maximum. Do not force it to rotate further. 12 1

11 All non-rohs products have been discontinued, or FH will be Series.5 discontinued soon. mm Please Pitch, check 1.2 the products mm above status on the the board, Hirose website Flexible RoHS search Printed at Circuit & Flexible Flat or contact Cable your ZIF Hirose Connectors sales representative. Precautions 4 When operating the actuator, do so at the center portion. 5 As illustrated, do not attempt removal or repositioning of the actuator. S FPC Insertionq The FPC should be aligned parallel with the board surface and perpendicular with the connector (as shown), then completely inserted. Actuator Perpendicular with the connector FPC To assure correct electrical and mechanical connection do not insert FPC at angle. It must be fully inserted. Make sure that the FPC is NOT MOVED during the closing of the actuator. SFPC Insertionw When inserting the FPC, do not forcefully rub against the bottom surface of the connector insertion entrance. Doing so will result in the contacts and FPC making strong contact and may cause deformation of the contacts, peeling of the FPC conductor, and other problems. Peeling of FPC conductor 11

12 All non-rohs FH products Series.5 have been discontinued, mm Pitch, or will 1.2 be discontinued mm above soon. the Please board, check the Flexible products Printed status on the Circuit Hirose website & Flexible RoHS search Flat at Cable ZIF Connectors or contact your Hirose sales representative. Precautions SVerification of the fully closed actuator. The actuator should be fully closed (as illustrated) and the FPC held firmly in the connector. Do not press against the actuator when is fully closed. Max force applied to the fully closed actuator should not exceed 1 N. Routing the FPC (FPC fully inserted/ actuator closed) SFPC Load Do not apply force in excess of.15n max. in the upward direction (as illustrated). Do not bend the FPC too close to the actuator. Load:.15N max. Removing the FPC Rotate the actuator to the open position (maximum open angle of 12 ). Carefully withdraw the FPC. 12 Other Precautions SHand Soldering Precautions When hand soldering: 1 Do not perform reflow or hand soldering with the FPC inserted in the connector. 2 Do not apply excessive heat or touch the soldering iron anywhere other than the connector leads. Do not use excessive amount of solder or flux compounds. Operation of the actuator and contacts may be affected by excessive amounts of solder or flux compounds. 5-2,OSAKI 5-CHOME,SHINAGAWA-KU,TOKYO ,JAPAN PHONE: , FAX: The contents of this catalog are current as of date of publication. Contents are subject to change without notice for the purpose of improvements.